Search Documents

By Michelia Alba, Ronaldo S. Sampaio, Davi S. Braga, Mathieu Dubé

Climate change is pressuring industries and governments for decarbonization commitments, research, testing, and use of best practices to achieve the target of global warming below 1.5/2 °C. As it accounts for as much as 7% of all global CO2 emissions and 7% of energy consumption, the steel sector needs to address this issue with extended efforts. This paper provides information on the key potential of renewable biochar as an alternative fuel for pellet production. It also summarizes the successful application of biochar in a pioneering case study as the main fuel for a Grate-kiln pellet plant in Brazil, as well as the study of its use to replace coke and anthracite as an additive for iron ore pellets and other possible applications in the steel industry in COREM's precompetitive research & innovation program. The final discussion reveals the large quantity of biochar required by the Brazilian and Quebec scenarios for reducing CO2 emissions of iron ore pelletizing plants.

Jan 1, 2023

By J. B. Gayle

The removal of coal particles from a slurry by flotation is made possible by the formation of stable aggregates with air bubbles of suitable sizes. The formation of such aggregates is theoretically possible only for certain favorable combinations of the solid-liquid-gas interfacial tensions. Because interfacial tensions involving solid phases are not conveniently measurable, a related variable, the contact angle, frequently is used as a measure of the floatability of various materials. Zero angles indicate nonfloatable substances, and large angles indicate substances having a high degree of floatability. During a study of contact angles for coal and substances related to coal in their similarity of response to various physical and chemical treatments, particularly flotation, carbonization, and oxidation, the reproducibility of replicate determinations taken within a 4-hour period was found to be much better than that for comparable results taken over a longer period of time. Consideration of possible causes for these differences led to an investigation of the effects of temperature variations on contact angles. References to literature revealed only a small amount of information, some of it apparently conflicting. Specifically, Sutherland and Wark4/ found that temperature variations "within limits" did not appreciably influence the angles measured for galena conditioned with potassium ethyl xanthate. On the other hand, McGlashan and McLeod5/ presented preliminary data showing that for sphalerite conditioned with potassium ethyl xanthate the angle is maximum at 25° to 35° C., depending on the pH of the system.

Jan 1, 1960

By H Utama, R Heryadi

PT Indo Muro Kencana (PT IMK) is a surface gold and silver mine located in Mt. Muro area, Central Kalimantan province, Indonesia. The mining operations of multiple open pits using combination of excavator and haul truck is operated. This operation is performed in two shifts in a day. The articulated dump truck (ADT) with capacity of 40 t and 60 t deliver ore to the mineral processing plant and discard waste material to the waste dump area. Overall, PT IMK’s mining operation department is consisting of two sections, namely mining operation section and drill and blast section. Firstly, mine operation section is responsible to manage loading, hauling, pit service (mine dewatering, earthwork, road maintenance) and mine operation engineering. Secondly, drill and blast section is in charge to manage drilling and blasting (blast engineering, blasting operation, explosive permit and magazine or explosive storage). Additionally, conventional blasting method (ore-waste blasting) with non-electric initiation system is used and sleep blasting is undertaken as bulk explosive is buried for maximum two days. The first purpose of this paper is to elucidate about role of mining engineer in mining operation department (mining operation engineer and D&B engineer). At this point, mining operation engineering practice (fleet management system, production control and mining manpower management) and also blasting daily practice will be elucidated. Daily blasting practice is consisting of surface blast design, explosive engineering, sleep blast practice and the concept of scaled depth of burial to ensure a safe work environment in blasting activity. Next, the second purpose of this paper is to explore workforce evolution and future skills for mining engineer in surface mining operation. Furthermore, strategy to advance future skills such as mining continuous improvement program, training and skills development for mining engineer (mining operation engineer and D&B engineer) in order to develop their skills is also discussed. It is expected that in the future, these future mining leaders will become new mining leader, for instance mining superintendents, D&B superintendents and mining managers. In conclusion, it is clear that awareness about workforce evolution, professional development, training, skills development, mining economics awareness and mining continuous improvement program are essentially required as professional development for mining engineer (mining operation engineer and D&B engineer), in order to be commercially competitive in their future career and in order to be adapted with future workforce evolution in mining.

Sep 1, 2024

By Herman D. Mendoza

A rapid recovery/recycling process was introduced utilizing the surface-chemical properties of finely dispersed mercury and alumina (Al2O3) fibers in aqueous environment. The conventional method of amalgamation or .ball milling. involves the mixing of a substantial amount of mercury to collect free gold during the grinding stage. In effect, a portion of the mercury is transformed into minute droplets that readily float and disperse in the amalgamation effluent. The fine droplets of mercury in the dispersion readily attached onto the positively charged macroscopic alumina fibers (i.e. = pH 9.8) at conditions pH 3 to 10. When an effluent from settling procedure after an amalgamation-grinding stage is passed through a column-bed packed with alumina fibers, maximum collection of negatively charged finely dispersed mercury occurred at pH 3 to 6. The collection/attachment efficiency was 99.5%. The collected droplets of mercury, which are left in the column-bed of alumina fibers, were subsequently rinsed with alkaline solution at pH 10 to 11.5. At these conditions, both mercury and alumina fibers carry negative surface potentials and resulted in the partial detachment of mercury from the alumina fibers. The detachment efficiency was only 30-35%. The attachment/detachment mechanisms in this study were analyzed using the DLVO theory.

Jan 1, 2003

By G Tsatouhas, R Newell, K Y. Wong

A sulfide ion selective electrode was used to control sulfidiser addition in the flotation testing of a synthetic and a naturally occurring ore containing malachite in order to compare the behaviour of sodium sulfide and calcium polysulfide. Both slug and controlled potential sulfidisation methods of addition were used. Under defined optimum CPS conditions, calcium polysulfide was a more effective sulfidising agent than sodium sulfide on the basis of both capital and operating costs. Surface and solution studies were used to compare the mechanism of each sulfidiser. For calcium polysulfide, XPS showed that polysulfide ions are adsorbed, whereas for sodium sulfide it is the hydrosulfide ions that are adsorbed on the mineral surface. For calcium polysulfide, the CuSx layer was believed to form on the malachite surface, which promoted the flotation of the malachite, by xanthate. Studies of surface morphology of the sulfidised malachite showed that a fairly uniform sulfidised layer is formed with both reagents. The use of sodium sulfide resulted in a thinner initial sulfidised layer compared to polysulfide at equivalent initial sulfur concentration.

Jan 1, 2005

By J. B. Gayle

In a modern blast furnace, production depends, to a large extent, on the rate at which the furnace gases can be forced through the charge. Since these gases must make their way through the voids between particles of coke, ore, and limestone, the size and size distribution of the stock-column materials are of considerable importance. Also, because the coke pieces support the weight of the overburden and provide the majority of the voids through which the gases pass, their ability to withstand the shattering and abrading forces to which they are subjected should be related to the maximum obtainable production for any particular furnace. Although the wide acceptance of this point of view is indicated by the ever-increasing demand for stronger and more uniform blast-furnace cokes, economic considerations demand that a quantitative evaluation of the relation between coke quality and blast-furnace performance be made available to the industry at the earliest possible date. The following studies of size-distribution patterns and breakage processes were, therefore, conducted as a part of a preliminary investigation intended as a basis for future studies of the relation between coke quality and blast-furnace performance. The major findings may be summarized as follows: 1. New evidence for the presence of two independent distributions of sizes in run-of-oven cokes has been obtained, and a method for characterizing and estimating the relative importance of the individual distributions has been demonstrated. This method has also been used to study the different types of degradation taking place during the tumbler test.

Jan 1, 1954

By A. Pearson, Auld. F. A., S. O. Colbeck

"To minimise mine shaft maintenance over the long-term, some potash mine shaft sinking projects have required the provision of a continuous fully welded waterproof steel liner over a substantial depth to achieve zero water ingress. This brings many challenges, including the implementation of a bottom-up construction sequence incorporating extensive waterproof welding and how to ensure the integrity of the welded liner when subject to substantial temperature fluctuations that are likely to occur with a composite steel-concrete liner placed within an artificially frozen shaft excavation. This paper highlights the key challenges and discusses multiple mitigation measures including vertical shaft movement joints and a combined structural-thermal analysis approach. INTRODUCTION Whilst the application of combined steel and concrete shaft liners using a fully welded steel liner is not new and has been used in several previous projects, most notably at Lanigan (Storck, 1968 & Roesner, 1980), recently the need to provide a continuously welded steel waterproof liner for over 800 m length of shaft for a potash mine has been considered. The need for a fully continuous welded steel liner arises from the perceived benefits of providing a fully dry shaft environment to; increase the life expectancy of the shaft; reduce routine maintenance particularly combatting salt accretion and minimising wash down practices; and improve long-term ground stability by preventing salt dissolution. Whereas previous projects have employed discontinuous sections of steel liner, when a fully continuous liner is employed longitudinal shaft strains from thermal changes result in significant deformations that must be either explicitly accommodated or resisted. Note, these thermal vertical expansion forces are more than capable of lifting the shaft collar and head frame structures should they be fixed in place. Typically, shafts are designed to resist vertical forces (collar loads and self-weight) by creating mechanical interlock with the adjacent ground. In competent rock this occurs incrementally with the construction of the shaft liner, and occasional hitch/crib structures are constructed as intermediate foundations to guarantee the transfer of vertical forces at distinct horizons. Usually this means cribs are constructed at first rock head, above the station level, and at the sump, although sometimes additional cribs are formed when entering and exiting weak strata or when a change in shaft liner construction is required."

Jan 1, 2019

By R. Craig McClung

Contrary to other sulfide minerals, where recovery is principally liberation controlled, the recovery of molybdenite is more complex. It is this complexity that initiated a geometallurgical investigation of molybdenites from Bingham Canyon. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes have on recovery. All samples were analyzed using normal mineralogical techniques. The results reveal the presence of two distinctly different types of molybdenite. These have been identified as the two polytypes of molybdenite: i.e. hexagonal (2H); and rhombohedral (3R). The 2H-polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the current pit bottom. The 3R-polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance and are concentrated along the margins of the current pit. Concerning their metallurgical behavior, each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. The 2H-polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This results in the production of a high quality concentrate under normal operating conditions. The 3R-polytype, by comparison, is difficult to grind and kinetically “slower” floating with surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R-polytype, modifications to the normal operating parameters may be necessary to improve recovery. This investigation highlights the necessity for understanding the mineralogical characteristics of any economic mineral(s), as these will have a direct impact on recovery.

By Gunter Fauth

The setting of tasks for the process control of coal cleaning, and in this connection the requirements for instrumentation can be classified into the following three fields: - Monitoring the operation of individual units, or process steps, - Control of units or process steps, - Control of the entire coal cleaning process with the intention of optimizing the operation and the profitability of the process. Instrumentation is affected by the type of cleaning processes. For introduction Figure 1 shows the simplified flow sheet of coal preparation which is usual in the German Ruhr District and in which desirable places for the measurement of ash, moisture and sulfur content are marked. The preparation plant is supplied with run-of-mine coal from the shaft via a homogenization facility. In a first step of primary classifying the raw feed coal is screened at about 10 mm. The raw coarse coal ( = 10 mm) is sorted by jig washers or heavy-medium separators. the raw fine coal (< 10 mm) at first is pneumatically sized at about 0.5 to 0.75 mm. The fines, the aspirated dust, are a finished partial product which will be added to the final metallurgical or steam coal. The material 10 to 0.75 mm subsequently is sorted in fine coal jigs and dewatered in centrifuges. The sludge obtained with the wet cleaning processes is dewatered in thickeners and fed to the flotation. Concentrate and tailings are dewatered by filters or bowl centrifuges and by chamber filter presses or belt filter presses, respectively. The partial products coarse coal, fine coal, flotation concentrate, aspirated dust, and middlings are blended to result in the sellable products metallurgical and steam coal.

Jan 1, 1984

By Chris Harris, Kamal Adham

The use of HCl acid is gaining momentum among hydrometallurgical processes. However, the issue of environmentally efficient and economically viable ways to regenerate HCl acid (from various metal chloride intermediate products) remains a technology and operational challenge. The authors provide a state-of-technology review based on Hatch’s years of testing, design and commissioning experience with high-temperature units (fluid bed and spray roasters), plus the recent efforts in the area of low-temperature HCl regeneration.

Jan 1, 2014

By A. Alwasel

Musculoskeletal disorders (MSDs) threaten the wellbeing and livelihood of a large number of construction workers incurring a significant cost to society. We present a new method to monitor and diagnose MSD risks in the workplace. The sensing unit of the system is an optical encoder encompassed within a non-intrusive exoskeleton to measure the joint angle of interest. This sensor can be applied to ball-and-socket and hinge-type joints of the human body, such as the shoulder, elbow, and knee joints. The system is contactless and does not require markers or cameras. Angle measurements are acquired directly without mathematical post-processing, thereby avoiding numerical noise and drift challenges. The system is a simple, robust, and deployable, but it currently lacks resolution of parallel degrees of freedom.

Aug 1, 2013

By Mavor S.

Further discussion at the Mining Institute of Scotland's general meeting held in Edinburgh, 12 February 1916, with D.W. Mowat, president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1915, vol. L, p.625 and discussed vol. L, pp.92, 433, 468, and 704 included comments by Mowat D.W. and the author's reply

Dec 1, 1916

By A. Yadav, B. Behera, G. S. P. Singh

The size of chain pillars in the Indian geo-mining conditions is primarily decided in accordance with the regulatory provisions. These provisions are of little help for deep longwall workings, exceeding the cover depth of 360 m. Furthermore, these provisions are primarily meant to support pillars in bord and pillar workings. They may not be suitable for the chain pillars owing to a significant difference in layouts and functional requirements. Hence, it is imperative to develop a method to evaluate the stability of the chain pillar considering the complex loading and geo-mining conditions. To this end, a machine learning-based model was developed in this study to assess the stability of the chain pillars under high depth of cover considering the field-representative conditions. The data for this work was generated by conducting a parametric study using a field-validated numerical model. The strength and deformability parameters of the caved, fractured, and continuous deformation zones were established by calibrating the numerical model outcomes against the site-specific field observations. The developed ML model was used to evaluate the influence of pillar width, pillar height, cover depth, abutment angle, face length, coal strength, moduli ratio of the roof and floor strata to the coal seam, and the elastic modulus and unit weight of the overburden on the chain pillar stability. An interesting finding of this study showed that the factor of safety of the chain pillar increased with the increasing abutment angle, which may be indicative of the confining effect of the abutment angle on the pillar. Eventually, the ML model was verified by comparing its outcomes with the calibrated numerical model for a typical longwall working from Indian geo-mining conditions.

Oct 18, 2023

By Steven P. Oman

Large room and pillar mines are characterized by numerous and widespread working places. Ventilation requirements are high since each panel employs men and equipment that work simultaneously in multiple headings. Also, it usually is not feasible to redirect airflow from idle to active panels as the demands of each shift vary so every panel in the mine is fully ventilated at all times. Ventilation requirements will be even higher for mines that are classified as gassy. As a result of these considerations, ventilation systems for room and pillar mines are generally designed to handle large quantities of air. But as mining progresses and the mine be- comes larger, greater demands will be placed on the ventilation system. To insure that adequate ventilation is maintained at these times, ventilation engineers must anticipate problems and plan how best to deal with them.

Jan 1, 1983

By Milka Madahana, John Ekoru

For efficient management of operations, mining companies are required to be able to predict potential scenarios for main market factors. Competitive advantage and value creation are established through managing the value chain well. The mining value chain is usually faced with challenges from various shifts in commodity markets as well as ongoing uncertainties. Therefore, there is a need for accurate analysis of data from the markets, for the prediction of commodities, for instance, Precious Group Metals (PGM). The main objective of this research work is to apply machine learning methodologies with the aim to identify patterns and trends in the Precious Group Metals, and thereafter analyze and predict the future trends of these markets. Numerous machine learning models are applied to a dataset consisting of 15 years of daily price for eight precious metals namely Platinum, Palladium, Rhodium, Ruthenium, Osmium, Indium, Silver, and Gold. The results reveal the patterns and trends within the data sets and that different machine learning methods could be suited for the prediction of market prices for each of the PGMs. The application of an amalgamation of various machine learning methods may result in more accurate predictions of the PGM markets. Accurate prediction of market prices for PGMs will possibly result in unlocking untapped sources of value in the mining industry.

Jun 25, 2023

By N. Mejia, Z. Xiao, D. Fragomini, A. R. Laplante

"The adaptation to platinum-group minerals (PGMs) of a protocol developed to predict gold recovery by gravity is presented. The protocol is based on three different data sets: ore characterization of gravity-recoverable minerals, description of their behaviour in cyclones and ball mills, and performance of recovery units. Examples of these are given. It is shown that the gravity-recoverable PGM (GRPGM) content can be very high. A case study at the Clarabelle mill is presented. Sperrylite is the dominant platinum mineral, and its partition curve is very similar to that of gold, despite its lower density. Its grinding kinetics is significantly higher than for gold. As a result, sperrylite accumulates in finer sizes than native gold, but can still be recovered by gravity or flash flotation. Recovery projections based on gravity recoverable data are presented.BACKGROUNDReliable modeling of gold recovery by gravity or flash flotation from a grinding circuit is based on the ability to describe the properties of gold-bearing particles in the ore, their behaviour in grinding and classification units and the performance of the equipment used for recovery, be it gravity or flotation. This is shown in Figure 1."

Jan 1, 2004

By A. L. Karyakin

The report focuses on the process measurements of the mass of rock in the bucket power shovels and dragline excavators. The mathematical models are suggested of AC and DC electric drives of excavators. These models are a basis for calculation methods of the electric drive electromagnetic torque. The design schemes of mechanical equipment of excavators considered to account the situation of bucket in the plane of the boom. The methods of static moment allocation and identification of the excavator technological operations are developed. The results of the work are experimentally tested on power shovels with bucket capacity of 12 and 18 m3.

Aug 1, 2013

By J. Wong, M. G. Lipsett, L. K. Daneshmend

"Current trends of increased size, complexity, and automation of surface mining equipment necessitate more comprehensive and objective techniques for equipment comparison and selection. The field of reliability analysis provides tools to generate quantitative bases for maintenance and reliability aspects of such comparisons. Results from statistical analyses of failure and repair time data are used to perform the comparison. A case study is presented which analyzes five machines of two different technologies and three different designs.IntroductionThe surface mining industry is currently faced with a rapid evolution in production equipment. The more obvious trend in this evolution is the steady introduction of even larger machines. Parallel, and complementary, to this increase in size is the introduction or adaptation of new technologies. Together, these two trends result in new surface mining equipment designs; these designs are often more complex and may feature technologies that have yet to be proven for the application or at the scale they are now fielded.The prospect of significant automation of open pit equipment is also bound to add complexity to future equipment designs. Semi-automated features, such as drilling controllers (Aquila, 2000), have already been commercialized. Fully autonomous haul trucks have been demonstrated in open pit mines (Jackson and Zoschke, 2000). Design concepts for comprehensive teleoperation of open pit operations have been formulated (Lipsett, 1998).With this rapid availability and deployment of new technology and equipment, managers and maintainers are faced with a multitude of decisions regarding what equipment to acquire and what maintenance strategies to implement. In light of this evolution in mining equipment, it is necessary to develop better methods for making equipment management decisions (Dessureault et al., 1999; Paraszczak, 1999). The incentive for development of such techniques is that a large portion of an open pit mine’s operating cost is maintenance related, as shown in Table 1."

Jan 1, 2000

By N L. Turner, K Ehrig, V Liebezeit, D J. Robinson, L L. Kuhar, N Francis

Conventional industry tests used to determine leach recoveries are often fully monitored and may be time-consuming and expensive. Such tests may be limiting in geometallurgical applications where large numbers of samples are required to be processed for characterisation of an ore deposit. BHP Billiton currently use a fully instrumented leach test for characterisation of Olympic Dam uranium-rich samples. Researchers at the Commonwealth Scientific Research and Industrial Organisation (CSIRO) were approached to develop an alternative to these full-scale leach tests that could allow for the ranking of samples in terms of their leachability. The novel geometallurgical test was required to use samples of small mass and be affordable and rapid.Three leach test protocols were pursued in developing the small-scale tests. Kinetic leach tests were performed using mild conditions at higher pH, low temperature and low oxidation reduction potential, moderate conditions at intermediate pH, temperature and oxidation reduction potential and aggressive conditions at lower pH, higher temperature and higher reduction potential.This paper presents results from 44 leach tests on 11 samples with varying uranium mineralogy. The developed small-scale tests correlate well with data from the more costly conventional industry laboratory tests, indicating the possibility of using this alternative test as a geometallurgical leach proxy. Simple regression analysis confirmed the importance of pH, reduction potential and temperature on uranium extraction. Experimental data were fitted to published leach models to predict uranium leach extraction for a range of operating conditions.The ultimate aim of the test work is to combine a limited number of large-scale calibration tests, a large number of small-scale geometallurgical tests and leach models for geometallurgical sample characterisation and evaluation of a wide range of scenarios or processing options.CITATION:Turner, N L, Kuhar, L L, Francis, N, Liebezeit, V, Ehrig, K and Robinson, D J, 2013. Development and testing of a small-scale uranium leach for geometallurgical applications, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 345-350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluated the effect of bucket orientation and operating parameters on resistive forces and penetration for rubber tire loaders. The work used a 1:16 scale LHD model to test a rubber tire loader (RTL) bucket operating at different levels of tractive effort, speed, digging height, and rake angles in a full factorial design experiment. The work repeated the test on two different muck piles with different particle sizes and used generalized regression modeling to test the association of rake angle, tractive effort, speed, and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort, and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle, and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The observation that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces is a novel contribution that enhances our understanding of RTL loading. The results also show that the effect of speed, tractive effort, and height above the floor all change with changes in particle sizes. This work adds to the literature on the effect of rake angle, height above the floor, tractive effort, and speed on penetration and resistive forces for rubber tire loaders.

Aug 24, 2020