Search Documents

By L. Hanschar, C. Bwalya, E. Mokola, K. Musonda, A. Makayi

This paper describes the installation, commissioning and operation of porous plugs featuring nitrogen gas purging in both Anode Furnaces at the Kansanshi Copper Smelter (KCS), a greenfield copper smelter which commenced operation in March 2015. The decision to install porous plugs was taken in November 2016 and the facilities were successfully commissioned on both anode furnaces in October 2017. The project was successful and has demonstrated the following process improvements: 12.2% reduction in main burner fuel consumption Larger average charge size, due to fewer accretions; 17 minute decrease in average refining cycle times Improvements in slag skimming operations Improved casting rates INTRODUCTION Porous plugs The application of porous plug technology in copper smelter anode furnaces is well established around the world. Vukovic and Gamweger (2017) and Wallner (2004) noted that the stirring and mixing action induced by the injection of inert nitrogen gas into the molten copper via porous plugs has potential benefits in the following areas: Homogenization of the temperature and composition of the molten copper resulting in Reduced fuel consumption Less tendency to overheat slag (reduced risk of refractory attack) Less slag produced with a lower degree of oxidation (lower rate of refractory wear) Less tendency for buildups to form Improved environmental performance (produce low sulphur blister at Peirce Smith converters) Elimination of buildups inside the furnace and potential for larger charges per cycle Reduced processing times and potential for shorter cycle times More efficient skimming of anode slag Shorter skimming time Less copper carry over to Peirce Smith converters Very little slag remaining in the furnace (reduced potential for buildups to form)

Jan 1, 2019

By J. V. Byrnark, R. W. von Bitter

The Hibbing Taconite Co. concentrator flowsheet, which is noted for its simplicity, uses single- stage autogenous grinding coupled with two stages of magnetic separation and two stages of size classification to produce a magnetite concentrate. This paper discusses the pilot-plant development of single-stage grinding, the commercial mill grinding performance, and mill liner development. Process innovation discussion includes process control computer implementation, size classification improvements, mill speed changes, magnetic separator improvements, and quality control innovations.

Jan 1, 1987

By James M. Stuckey

In a search for improved methods of upgrading tar obtained by low-temperature carbonization of coal, monoethanolamine (MEA) was found to be effective in extracting tar acids from coal tar distillates derived from a subbitunwous and a lignite coal. Patch extractions showed that both yield and purity of the extracted acids improved with increasing volume ratios of monoethanolamine to tar acid, varied from 1:4 to 8:1. Yield improved, but purity decreased as the concentration of monoethanolamine was changed from 30 to 70 volume-percent, and as the concentration of tar acid in distillate was increased ad from 14 to 45 percent. In a continuous countercurrent extraction employing a double solvent (monoethanolamine and hexane) approximately 80 percent of the tar acids was extracted from 170° to 350° C. tar distillate when using 1.6:1 volume ratios of amine:tar acids. Tar acids isolated from his extract, although of improved purity, contained appreciable quantities of neutral oils and some tar bases. Aqueous monoethanolamine was not effective for extracting the last 10 to 15 percent of tar acids in 170° to 350° C. distillate oil from lignite coal. The highest yield of isolated tar acids and the best recovery of monoethanolamine were obtained by diluting the extract with water and saturating with C02. Some losses of solvent were encountered when aqueous monoethanolamine solutions were heated through decomposition of the amine with the liberation of ammonia.

Jan 1, 1960

By Loren R. Anderson

This Volume documents the use of the Cone Penetrometer data analysis computer programs VERT and HORZ. The programs are interactive in that they prompt the user for input data and allow correction and modification to be made. The programs read data from the results of cone penetrometer soundings and convert the data to values of tan ø. Mean, standard deviation, skew, kurtosis, linear trends and autocorralation are computed by the programs.

Jan 1, 1982

Clean Diesels fuel-borne catalyst, Platinum Plus, helps improve fuel economy for all engines up to 10 percent while reducing particulate emissions by up to 25 percent. When used with a simple diesel oxidation catalyst, particulate emissions can be reduced by 30 to 50 percent. The use of Platinum Plus enhances combustion in the cylinder, burning fuel more completely. This reduces CO2 and other greenhouse gases and lowers total operating costs by improving fuel economy.

Jan 1, 2007

By T M. El Hajj, A C. Chieregati, M T. G C Marques, J M. Braga Jr, H Delboni Jr

"The estimate and control of sampling errors is essential for all mining operations, especially when dealing with strategic materials, such as niobium. This paper is based on a traditional quality assurance and quality control technique used to confirm mineralised intersection zones, and proposes the validation of sampling data using diamond drill twin holes, in order to evaluate and improve the quality of the current data set. The geological model of the niobium mine – located in Araxá, Minas Gerais, Brazil – was built including 77 diamond drill holes of a sampling campaign carried out during the 1970s. There are few records about the collection and preparation procedures of these past samples, making it difficult to estimate the errors associated with their analytical results. Therefore, 11 twin drill holes were drilled to compare their samples against the samples from the 1970s drilling campaign. The new hole locations were chosen as near as possible to the old holes location. The JORC Code, 2012 edition, relates the use of twin holes as a good sampling technique to assess sampling and assay data. Three parameters were considered to validate the 1970s drill hole campaign by the twin drill hole campaign: the difference of the coordinates between the paired holes the difference among the positions of the geological contacts to validate the geologic description the difference between the paired samples grades was calculated to validate the analytical results.The analysis of the grade range variation between sample pairs was based on three techniques: geostatistical interpretation of vertical semivariogram to obtain the nugget effect calculation of the relative difference between duplicates calculation of the error associated with the sampling protocol established according to Pierre Gy’s Theory of Sampling.The results were satisfactory for hole coordinates; however, the ore content showed a high deviation, although this divergence can be explained by the nugget effect. For the lithological intervals, the new results contributed to an effective identification of variations among lithologies, ie brown weathered ore and saprolite. The twin drill holes campaign successfully validated the geological model data, allowing effective mine planning and higher reliability of the reconciliation results.CITATION:Marques, M T G C, El Hajj, T M, Braga Jr, J M, Chieregati, A C and Delboni Jr, H, 2017. Theory of Sampling and geostatistics for twin drill holes analysis in a niobium mine in Araxá, Brazil, Australia, in Proceedings Eighth World Conference on Sampling and Blending, pp 97–106 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By Milan Yekich, Emanuele Cauda, Justin Patts, Cody Wolfe

A worker’s personal exposure to respirable dust in occupational environments has traditionally been monitored using established methodologies which entail the collection of an 8-hour representative sample that is sent away for laboratory analysis. While these methods are very accurate, they only provide information on the average exposure during a specific time period, generally a worker’s shift. The availability of relatively inexpensive aerosol sensors can allow researchers and practitioners to generate real-time data with unprecedented spatial and temporal granularity. Low-cost dust monitors (LCDM) were developed and marketed for air pollution monitoring and are mostly being used to help communities understand their local and even hyper-local air quality. Most of these integrated sensing packages cost less than $300 per unit, in contrast to wearable or area dust monitors specifically built for mining applications which have been around for decades but still average around $5,000 each. At the National Institute for Occupational Safety and Health (NIOSH), we are leveraging the power of high-volume data collection from networks of LCDM to establish baseline respirable hazard levels and to monitor for changes on a seasonal basis as well as following any application of control technologies. We have seen the effective use and advantages of monitoring live data before, during, and after events like shift changes, operational changes, ventilation upgrades, adverse weather events, and machine maintenance. However, many factors have prevented a systematic adoption of LCDMs for exposure monitoring: concern for their analytical performance, the complexity of use, and lack of understanding of their value are some factors. This contribution outlines a one-year case study at a mine in Wisconsin USA, covering the installation, maintenance, data visualizations, and collaboration between NIOSH researchers and the industrial hygiene professionals at the mine.

Feb 1, 2024

By Karl Berger, Roman Schneeweis, Dietrich Mathweis

With increasing demands from customers to provide flat strip with tighter tolerances on material properties, particularly flatness of e.g. martensitic steel grades (M1500), it has become necessary to develop strategies to improve flatness without influencing the tensile properties for such hard steel grades. Usual skin pass mills are not capable to apply sufficient tension and roll force for these kinds of material to improve the flatness. Therefore, alternatives had to be searched for. This paper describes skin pass - / temper – rolling methods from the classical one to new alternatives in order to satisfy the demanding market of higher material properties and idle running mills in rolling plants.

Oct 1, 2019

By Yves Prévost, Guy St-Amant, Guillaume Dion

In 2010, the foreseen increase of copper grade in feed concentrate at the Horne Smelter was a significant challenge to maintain a steady copper flow throughout the process. The Horne Smelter process includes a Noranda Reactor, a Noranda Converter, pyro refining vessels and anode furnaces. Of the many challenges involved, improving the single casting wheel performance was one of the key topics. Its reliability had to be improved to meet the new production objectives, as anode copper production was to increase from 170 000 to 225 000 tonnes/year. A multidisciplinary team was dedicated to improve the casting wheel availability. The improvement project allowed pinpointing failure modes and reviewing operational and maintenance practices. The common understanding developed by the team allowed improving small components with a high gain-to-effort ratio. The project allowed reaching operational targets without any significant investment. INTRODUCTION In operation since 1927, the Horne Smelter, located in Rouyn-Noranda, in Quebec, has undergone several technological changes since its original construction. Built to smelt the Horne mine concentrates, the smelter also accepted some local custom feeds from the first years of operation. When the Horne mines stopped production in 1976, the plant became a 100% custom smelter. With the development of the Noranda Reactor (1973) and Noranda Converter (1997), the Horne smelter increased its productivity and improved its environmental performance. Continuous improvement of the Horne process allowed maintaining a high level of flexibility in the operation of the smelter, while improving its overall capacity.

Jan 1, 2019

By G. Deschênes

In the last 4 years, the high price of silver attracted more interest for improving its extraction. Metallic silver and silver minerals require a high concentration of cyanide and show slow leaching rates and poor extraction. This investigation determined the effects of dissolved oxygen, lead nitrate and a pretreatment on silver leaching from slurry containing quartz mixed with metallic silver and high purity acanthite. Stephanite, pyrargyrite and polybasite were also used in the study. The silver minerals were characterized by chemical assay, X-ray diffraction analysis (XRD), image analysis (MP-SEM-IPS) and electron microprobe analysis (EMPA). Increased dissolved oxygen of the slurry produced the fastest silver leaching kinetics. The leaching of silver from high purity acanthite was determined under various conditions and compared to a new process called ?CANMET Enhanced Leaching Process (CELP). For a slurry containing acanthite, a 23% improvement (from 76% to 99%) in silver extraction was obtained with the CELP. In presence of pyrargyrite and polybasite, silver extraction increased from 75% to 90% and 86% to 99% respectively using the CELP. No improvement was obtained for the slurry with stephanite (99% extraction in 72 hours). However, the sliver leaching rate was much faster with the CELP. XPS analysis of individual silver mineral particles showed that CELP leached surfaces were considerably more oxidized relative to the conventional cyanidation leached surfaces. Leaching of two gold/silver ores indicated that the efficiency of the CELP increased with the refractoriness of the sample. Gold extractions were comparable for the two technologies while silver extraction improved up to 5% (70g/t) for the CELP. The final leach solutions contained lower concentrations of copper, which consequently reduces the effluent treatment costs.

Jan 1, 2014

By Y. R. Murthy, S. Angadi, A. K. Bhatnagar, S. K. Tripathy, L. O. Filippov

Dolomite is an essential raw material for the refractory industry, a flux in the iron and steel industry and also for the extraction of magnesium metal. Generally, particle size reduction, screening and classification are used for the preparation of the high-grade sized material for different applications, whereas low-grade fine fractions are not utilised. These fines or low-grade overburdens are dumped at the mine site for future utilisation, which creates environmental issues along with inadequate space management. In the present investigation, a detailed study was carried out to decrease the silica content of the low-grade dolomite fines from Gomardih , India, containing 28.6% CaO and 20.1% MgO along with 8.3% silica. Different process flow sheet options were evaluated with a combination of dry classifier, wet classifier, gravity concentrators as well as flotation. Different process variables were assessed along with mineralogical characterisation to optimise the process for efficient rejection of siliceous gangue minerals. Results indicated that dolomite, calcite and quartz are the major mineral phases present in the ore along with other minor minerals. It was concluded that two-stage flotation was an effective process for the reduction of silica up to below 1% after grinding to a particle size below 212 μm. A process flow sheet with a combination of gravitation air classifier and flotation can produce a concentrate with silica content below 4.5%. Keywords: Dolomite, flux, dry classification, flotation, characterisation, beneficiation

Jan 1, 2020

By Klaus M. Hahn, Kurt Aasly, Jutta Lennartz, Hermann Wotruba, Ben Snook, Przemyslaw B. Kowalczuk, Rolf Arne Kleiv

"Seafloor massive sulphide (SMS) deposits have been identified as important marine metal resources for the future. However, literature on mineral processing of SMS is currently limited, and to date, no research has been published on processing of SMS from either active or inactive hydrothermal vent fields on the Arctic Mid-Ocean Ridge. In this paper, individual SMS rock samples from the Loki’s Castle area were tested. Chalcopyrite, isocubanite and sphalerite represented the main copper and zinc bearing minerals in the SMS samples, whereas the gangue consisted of barite and silica. Based on the X-ray transmission response (XRT), i.e. differences in the atomic number of elements in tested samples, and using portable XRF (PXRF) values of elemental composition, individual particles were classified as a either product (low barium / high to low silicon / high copper and zinc) or waste (high barium / high silicon / low copper and zinc). The classification was based on the elemental composition of the samples with the cut-off grade equal to 0.5% for copper. It was shown that the XRT discrimination analysis correlated well with elemental (PXRF) data classification. The results clearly indicate that X-ray transmission sensor-based sorting can be used a useful technique for preconcentration of SMS rock samples. INTRODUCTION Due to different compositions of investigated samples, sensor-based sorting is a useful technique for preconcentration of different materials. The aim of using sensor-based sorting is to upgrade an ore by reducing the quantity of overall waste material reporting to the next processing stage. This can be achieved by eliminating (reducing) the waste fraction. By applying sensor-based sorting, the energy consumption for particle comminution as well as the required process water and reagents can be decreased. The total volume of the waste rejection leads to a proportional reduction in the total energy costs (Lessard et al., 2014, 2016)."

Jan 1, 2018

By M. M. Tilman

A series of alloys was laboratory prepared by adding up to 4 weight-percent cobalt to the basic composition of type AM 350 (AISI 633) stainless steel. Aging curves were established for each alloy at 750° F, 850° F, and 950° F for lengths of time up to 100 hours. A series of annealed steels containing as much as 1 weight-percent cobalt was cold-rolled 50 percent and aged for 3 hours at 850° F. No improvement in hardness due to cobalt was observed in the steels transformed by heat treatment. Slight improvements in hardness were observed in the steels transformed by cold working.

Jan 1, 1968

By S. H. Ash

For many years the Federal Bureau of Mines has been investigating fires and explosions in mines, tunnels, buildings, and hazardous processes of various kinds. Means and methods for controlling and extinguishing mine fires and preventing explosions and other accidents in many hazardous processes require the collection and analysis of samples of the atmospheres surrounding the sources of ignition. Complex mixtures of gases often encountered in mines, tunnels, and industrial processes may well presage imminent danger from explosions. This report discusses some practicable methods of utilizing the analyses of samples of complex mixtures of gases in their application to the many problems that arise from their presence.

Jan 1, 1948

By Jeff Kravitz, John Kovac, Wayne Duerr

Since 198 1, Federal mining law has required every miner working in underground coal mines to have a self-contained, self-rescuer (SCSR) available for use in emergencies. Some miners that have escaped from fires using SCSR's have reported that they had to remove their mouthpiece to talk during escape, thus compromising the protection afforded by the SCSR. If miners are in thick smoke during an escape, they may have trouble if they become separated from their group. The visibility can be so poor that separation can occur at very short distances. To address this problem, two-way, FM radios were built into the SCSR to improve the ability to communicate should the miners be separated over relatively short distances. The SCSR prototypes built and used in testing included both two-way radios and improved mouthpieces. Comparison studies were conducted using combinations of the new and old mouthpieces, and trials using the radio or not using the radio. Subjective judgments indicate that communication ability was significantly improved using the prototype devices. Communication problems have been encountered with teams using standard voice- powered communications systems. Mine rescue teams perform rescue and recovery work under extremely hazardous conditions, life lines are a standard part of mine rescue team equipment. Leaky feeder and quasi-leaky feeder life line communications systems provide significant improvements over standard systems. These improved systems allow all members of the team to communicate with each other and their base of operations. These innovations will significantly enhance the safety of mine rescue operations.

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By B K. Da, S A. Balaji, G P. Roy, T K. Dutta

The raw material handling complex at the Durgapur steel plant provides iron ore, crushed coke and flux to two sinter plants. Either some facilities were not envisaged or not properly designed before the project stage which caused problems during operation of the plant. The absence of an in situ roll turning facility, used to increase maintenance activities for disassembly, transportation of rolls to central machine shop and assembly of rolls, led to decreased crusher availability and increased activities for the maintenance crew. The provision of a smaller vibro feeder/screen in place of a suitable sized screen caused jamming of the screen deck, adversely affecting screening efficiency and the crushing index of crushed coke. Some design modifications and developmental work was undertaken, such as the development and installation of an in situ roll turning facility in the existing limited space, achieving low feed (0.1 - 0.2 mm/rev), lower cutting speed of 30 - 40 m/minute for 350 BHN hard roll, which was also a difficult engineering challenge to bring within the tolerable limit of vibration. This was successfully achieved. Modifications to the screen deck, introduction of differential speed crushing and modification to the vibro screen and vibro feeder for uniform distribution of feed have been incorporated. These innovative design modifications to the in situ roll turning have led to a drastic decrease in maintenance activities and an improvement in the crushing index. Modifications to the screen have resulted in the elimination of jamming and improved screening. Modifications to the vibro screen before the primary crushers and to the vibro feeder before the secondary crushers have prevented excessive wear in the central portion of rolls, ultimately leading to increased roll life. Incorporation of differential speed crushing has resulted in an increased crushing index and decreased generation of micro fines. All the above modifications have led to distinct improvements in equipment availability, increased roll life and a decrease in maintenance activities and improvement in crushed coke granulametry, ultimately resulting in improved productivity and quality of iron ore agglomeration at the sinter plant. The innovative design modifications mentioned above are discussed in detail in this paper.

Jan 1, 2005

By Chris Doyle

From 1997-2000. PT INCO undertook the Fourth Line Expansion Project (FLEX) to increase annual production rates from 90-100 to 150 Mlbs Ni/year (68,000 MT Ni/yr). In 2003, PT INCO nickel production underwent a major sustainable step jump that finally exceeded the targeted rate. This paper presents the changes that led to this achievement. The focus of mining changed. Improving Ni grade was important but only if electric furnace feed met target chemistry so that on-specification slag could be produced. The intensity of diamond core drilling for exploration was dramatically upgraded, mine planning strategy was totally re- vamped and an ore chemistry quality assurance team was formed. In the processing plant, measurement systems were upgraded for better control. Teamwork between sections vastly improved. The final step jump in production occurred when the fifth hydro-electric power generator was added to the furnace grid to allow the power-starved furnaces to cruise in operation at 70+ MW. Keywords: Free cash flow, Ore Chemistry, Measure, Control, Improve

Jan 1, 2004

By V. M. Paretsky

The basic work conducted by Prof. A.Yazawa has demonstrated that in order to ensure single- stage white metal production by autogenous smelting of copper sulfide raw materials, it is most favorable to use highly basic slags, in particular oxide systems CaO-FeO-Fe2O3-SiO2. The special studies have been conducted in the Gintsvetrnet Institute to investigate the composition and structure of slags produced on a semi-commercial scale when testing the KFP and FBP processes for white metal smelting. as well as the slag obtained in a full-scale KFP furnace at the Almalyk copper smelter. The investigations conducted have demonstrated why production of high-grade matte or white metal is associated with lower loss of copper in slag in a series: silicate slag I silicate-calcium slag I ferrite-calcium slag.

Jan 1, 2003