Search Documents

By J. J. Forbes

The original organic act establishing the Federal Bureau of Mines in 1910 and the amended act of 1913 indicated that promotion of the health and safety of mine workers was to be ore of the chief functions4/ of the Bureau. Many of the field and laboratory studies pursued by the Bureau are designed to improve conditions under dish minors must work. As the Bureau has no legal authority to enforce safety rules, it must rely upon cooperation of employer, employees, State mining or other departments, and labor organizations for success in promulgating its finding and making recommendations. The staff of the Safety Division, which is essentially a service organization of the Bureau, is composed of 28 safety instructors, 29 engineers, 18 clersk, and 7 others engaged in promotion of an educational program in an effort to improve conditions in the mining industry. The work is directed from 14 safety stations in the United States and 1 in Alaska. The work of the personnel, of the mine safety car that operates in. the anthracite region of Pennsylvania was supervised and directed by the district engineer in charge of the Wilkes-Barre (Pa.) Safety Station.

Jan 1, 1940

By J. W. Freeman, D. N. Frey

Fundamental reasons for the improvement in creep resistance of an austenitic alloy by cold working were investigated mainly by X-ray diffraction. The creep resistance was found to be improved by the internal stresses in the lattice of the alloy induced by the cold work. THIS investigation was concerned with the fundamental reasons for improvement in creep resistance of an austenitic alloy as a result of cold working. Also, the investigation was carried out to elucidate the conditions under which cold working could be expected to improve the creep resistance. To achieve these ends, creep resistance and internal structure were correlated for a variety of cold-worked conditions. Since the aim of the investigation was not to obtain specific and extensive information on any one alloy, creep testing was done with a single stress at 1200°F. Structural studies were carried out primarily with X-ray diffraction characteristics. The alloy used, low carbon N-155, was selected on the basis of being representative of at least some of the alloys used in gas turbines. Low carbon N-155 alloy in the form of %-in. sq bar stock was used in this investigation. The chemical composition, in percent, was: C, 0.13; Mn, 1.43; Si, 0.34; Cr, 20.73; Ni, 18.92; Co, 19.65; Mo, 3.05; W, 1.98; Cb, 0.98; N, 0.14; and Fe, balance. The bar stock was produced from a 13-in. sq billet, finished to 7/s in. round cornered square between 2060" and 1910°F. Prior to use in this particular investigation, the bar stock was solution-treated 1 hr at 2200°F and water quenched. This procedure was used in order to put the stock in a condition where effects of prior processing were minimized. Experimental Procedure The specific approach to the problem was twofold. First, the influence of cold working, under various conditions, on the creep rate under a single stress at 1200°F and on the internal structure was in part determined. Second, the effect of annealing at various times and temperatures on the creep rate and internal structure of the cold-worked samples was in part evaluated. The first step was basic to the investigation—creep resistance and structure were to be correlated. The second step was taken to see if the annealed samples showed some internal changes which could also be correlated with changes in creep resistance. This it was felt would facilitate solution of the basic problem. The creep and structural studies were carried out on samples reduced approximately 5, 15, and 40 pct at room temperature and 15 pct at temperatures up to 2200 °F. Annealing of various of the samples was done at 1200°, 1400°, 1600°, and 1800°F for time periods up to 1000 hr. Studies of the annealed samples were concentrated on materials rolled approximately 5, 15, and 40 pct at room temperature and 15 pct at 1400°F. The creep tests were carried out at 1200°F under 40,000 psi, the latter being approximately the 1000 hr rupture stress of the material

Jan 1, 1952

By Leo F. Reinartz

Part III of a four-part series on the history of steelmaking in the US, describes furnace developments, improvements during the last few decades, and the contribution of the AIME. THE invention of the dolomite machine was a great boon to the open-hearth furnaceman. By speeding up bottom making, it helped to increase tons per hour and decrease cost. The first homemade unit was built and operated before 1925 at the South Side works of Jones & Laughlin Steel Corp., Pittsburgh The first commercial machine, similar to those known today, was built for the Donner Steel Co., Buffalo, N. Y., in 1925. Heavy slab buckstays, 6 in. by 15 in., supplanted lighter I-beam buckstays as furnace framework in the middle 1920's. They greatly improved the rigidity of the furnace binding. Although the first sloping back wall had been in- stalled prior to 1920 on a small basic open-hearth foundry furnace at Columbus, Ohio, the impetus to install such back walls universally in ingots shops came after S. Naismith installed the first one on an open-hearth furnace at Illinois Steel Company's South works in June 1924. Before that event, back- wall life had already been improved somewhat by the use of chrome rock or metal-encased basic brick. Here again, these changes heralded major for- ward steps in furnace design, decreased costs, in- creased production, and improved safety and working conditions on the back standing of the furnace. Fuels Up to 1930, a number of different kinds of fuel were used to melt and refine steel in American open hearth furnaces. During World War I, powdered coal was used in a few plants as an open-hearth fuel, but because of the high sulfur and ash content in the coals, many operational difficulties arose. There were also dust, explosion, and accident hazards, so that after the War its use was discontinued. In some steel-manufacturing centers, natural gas was available as a fuel and gave good performance. In most steel-manufacturing centers, operators had to rely on producer gas made from bituminous coals in producer gas houses. Low-sulfur low-ash, high-fusion coals required for the manufacture of such gas were not readily available. The quality of producer gas was uncertain. The gas had to be pre-heated. Maintenance problems connected with the use of this fuel were serious. Tons per hour per month was unsatisfactory. Although petroleum had been first discovered by Edwin L. Drake at Titusville, Pa., in 1859, it was not until the early 1930's that heavy fuel oil residues for open-hearth use began to appear on the market. They were cheap; the calorific value was high, and it was not necessary to pass this fuel through the checkers to preheat it. Various plants began to use such oil as an open-hearth fuel. Others used it in combinations with tar, coke-oven, and/or blast-furnace gases. Because of its low calorific value, blast-furnace gas had to be preheated in the checkers. These fuels were cleaner and more dependable than producer gas. The dirty gas house adjacent to the open-hearth shop was no longer needed, and

Jan 1, 1961

By L. Lariviere, M. Grenier, R. Khalili, D. Shook

A mineral processing facility near Montreal, CEZinc, Noranda Inc., has recently implemented a leading-edge intranet solution for monitoring the performance of plant operations, and providing condition-based maintenance. This innovative multi-faceted software implementation incorporates: web-delivered plant information systems; area-wide control loop performance assessment (using sophisticated algorithms to evaluate poorly performing controllers); and integrated alarm management functions.The system has enabled a project to improve plant operations through better process control. Maintenance technicians, engineers, supervisors and managers all can see the performance of the controllers, and the performance of the plant itself, through webdelivered graphics and reports. Information is combined from many sources, real-time, historical, relational and analytical, to provide a complete picture of plant operation.The web-based solution centralizes the administration of user access, and simplifies the deployment of several different kinds of information to many desktops. It is an extensible system that allows users to create and share their own web pages and data views.The paper will discuss the solution architecture and the improvements the IT, operations, maintenance, and engineering groups have experienced, and overall benefits to the facility.

Jan 1, 2003

By T. McCallum, C. Cooper, C. Lewis

"Following a successful solvent extraction (SX) pilot plant demonstration in 2016, CYANEX® 600 has been used commercially to recover molybdenum from concentrate leach liquor since March 2017. Consistent with the piloting results, the commercial plant has achieved expected molybdenum recovery, a significant reduction in base consumption, and a step-change improvement in physical performance. This paper highlights the optimization activities and plant performance from startup through normal operation. INTRODUCTION Historically, tertiary amines have been the most commonly used extractant for molybdenum and rhenium recovery. Tertiary amines utilize a protonation of the ligand combined with an anion exchange mechanism as proposed in equations (1-2). R3N + H+ ???R3NH + (1) 4R3NH+ + Mo8O264- ???(R3NH+)4Mo8O264- (2) In addition to the transfer of Mo and Re, the amine transfers acid and other anions to the strip liquor. The undesirable transfer of other species increases base consumption during stripping, impacting operating costs. Additionally, lower solubility of molybdenum-amine complexes create operational challenges, resulting in diminished physical performance. The presence of colloidal Si in concentrate leach liquors and the formation of Pickering Emulsions adds to the physical plant performance challenges with the amine extractant. CYANEX® 600, a phosphinic acid-based extractant, uses a cation exchange mechanism proposed by equation (3). 2(H2R2) + MoO22+ ??(HR2)2MoO2 + 2H+ (3) The cationic exchange mechanism eliminates chemical transfer of acid and other anionic impurities and avoids some of the physical challenges of the amine extractant (emulsion and 3rd phase formation). In addition, the reagent offers high selectivity for Mo over Re, which may be desirable in certain moly pressure oxidation (POX) flowsheets. Alkali base (ammonium hydroxide, sodium hydroxide, sodium carbonate, etc.) is used for molybdenum stripping. Therefore, reduction or elimination of chemical acid transfer from extract can significantly reduce base consumption in strip. Extensive laboratory and pilot plant testing was completed to evaluate the use of CYANEX® 600 for molybdenum recovery at Freeport-McMoRan’s Bagdad operation. The test work and pilot demonstration confirmed a reduction in base consumption along with improved selectivity. In addition, the evaluation highlighted a step-change improvement in physical performance over the incumbent amine extractant. The decision was made to convert the commercial operation to CYANEX® 600 in March 2017."

Jan 1, 2018

By Campbell Robertson

The evolution of electronic detonators in commercial mining, construction and demolition has been a transformative journey, characterized by technological innovation, enhanced safety measures and improved precision. This abstract explores the historical progression and key advancements in electronic detonator technology highlighting its impact on the industry as well as the challenges in deploying these types of technologies. Electronic detonators represent a significant departure from traditional initiation systems offering precise timing capabilities and improved reliability and safety. The early development of electronic detonators can be traced back to the late 20th century with the introduction of basic electronic initiation systems. These early iterations provided a glimpse into the potential for greater control and accuracy in blasting operations. As technology progressed, electronic detonators underwent significant refinement incorporating advanced features such as programmable delay times, multiple firing sequences, expanded blast size and enhanced communication capabilities. These advancements revolutionized the way explosives are deployed in mining and demolition applications enabling engineers to tailor blasts to specific geological or environmental conditions and structural requirements. One of the most notable developments in electronic detonator technology is the integration of microprocessor-based control systems. These systems allow for precise calibration of detonation parameters, including timing, sequence, and energy distribution. By leveraging microprocessor technology electronic detonators have become increasingly sophisticated offering unprecedented levels of precision and safety in blasting operations. The advent of wireless communication technologies has further augmented the capabilities of electronic detonators. Wireless detonation systems enable remote initiation and real-time monitoring of blasting operations enhancing safety by reducing the need for personnel in hazardous environments. The evolution of electronic detonators has also been driven by a growing emphasis on sustainability and environmental stewardship. Modern electronic detonation systems are designed, amongst other objectives, to minimize environmental impact, achieve optimal fragmentation outcomes and reduced misfire rates during blasting. These advancements not only improve safety for workers and surrounding communities but also contribute to a more sustainable approach to mining and/or demolition activities. In conclusion, the evolution of electronic detonators has transformed the landscape of commercial mining and demolition offering unprecedented levels of data integration, precision, safety, and environmental responsibility. As technology continues to advance, electronic detonators are poised to play an even greater role in shaping the future of blasting and explosives engineering.

Jan 21, 2025

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery ? Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery ? Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2012

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Bradley Johnson

Introduction Since its creation in 1910, the Bureau of Mines has conducted a wide-ranging program of research on mining technology. Over the years, the Bureau has perhaps become best known for its accomplishments in mine health and safety technology, a field that has been the object of much public attention. Nevertheless, the Bureau's program in other areas of mining technology has always been strong and remains so today. A distinguishing feature of the current effort is its tendency to concentrate on high-risk, high-gain projects. Throughout the federal research establishment, the Administration's policy has been to phase out short-term research that could be performed by private industry, in favor of long-terms projects that industry cannot usually afford to fund. This tendency is evident in the following account of the highlights of the Bureau's current mining technology research program. Underground Mining Technology Fragmentation. Research studies on fragmentation have focused on nonexplosive concepts. If successfully developed, these concepts would lend themselves to continuous automated operation and reduce time and costs of fragmentation in underground mines. A special laboratory-scale device to investigate ripper cutting was designed and fabricated in 1982. Experiments were conducted with large drag cutters to develop an efficient cutting technique for hard rock. Tests were successfully conducted with 76- and 152-mm (3¬and 6-in.) bits in rocks up to 138-MPa (20,000-psi) compressive strength. Because of the success of these initial tests, larger-scale proof-of-concept tests are planned. To prepare for these tests, a tester capable of cutting a 1.8-m (6-ft) opening was fabricated. This device will allow ripper cutting to be carried out at full scale, and will also allow mucking and holddown requirements to be investigated. Preliminary estimates indicate that this concept has the potential to double excavation rates while reducing costs up to 30%. Mobile Hydraulic Monitor. A mobile hydraulic monitor system was designed, fabricated, and used to mine the St. Peter sandstone at an average rate of 22 t/h (25 stph) from a face in Martin-Marietta's foundry sand mine at Clayton, IA. A slurry transport system worked in tandem with jet cutting, resulting in a continuous mining and transport system. Problems with spray from the jet hitting the sandstone showed that a remote-controlled mobile monitor was needed at a station 15 m (50 ft) from the face, so the operator would have a clear view of the face and be safely out of the backwash. Crushers. Research on crushing systems to improve efficiency in underground mines is continuing. Final testing of a low-profile, portable crusher for underground applications has begun. A system for handling oversize feed to the crusher was conceived and tested. Underground crushing systems, portable enough to be kept near the face, offer considerable improvement in materials handling because main haulage by conveyor is often less costly. Hoists. Research to increase hoisting efficiency and speed and to reduce energy requirements has led to experimental ore skips. The skips feature guide rollers to improve riding characteristics, bearing improvement at critical locations, and weight savings of about 1.8 t (2 st). An experimental aluminum skip was installed last year at Kerr McGee's Church Rock mine. Performance is being monitored under production conditions. A portable service hoist for low-cost, efficient movement of men and supplies in raises between mine levels was designed, fabricated, and tested on the surface. The hoist has maximum equipment payload of 570 kg (1,250 lb) at

Jan 11, 1983

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By M. L. Maniocha

Most magnesia, MgO, whether of natural or synthetic origin, is utilized in its dead burned or periclase form as refractory linings for the production of steel. Continued research in refractory science combined with good refractory maintenance and improvements in steel making practice have resulted in decreased use of magnesia. To make up for this loss of business producers of synthetic magnesia have started to manufacture a variety of magnesium based chemicals that are utilized in many diverse industries and applications.

Jan 1, 1997

By W. Todd

The Robbins Company has developed a boring machine, with a rubber packer serving as the gripper system, for blind boring of raises without using drill pipe. This machine is the BorPak and has many applications for use in the mining industry which will improve productivity. In addition to the cost savings, the boring method will lead to increased safety in constructing blind raises. The advantages of using the BorPak in a mining environment will be discussed together with possible applications.

Jan 1, 1994

By Norman] [Seldle

This report describes the development of a mine machinery training system from initial conception through a task and skill analysis, a training system analysis, implementation of a prototype system, and initial validation of the prototype system. The objectives of the training are to improve safety and productivity simultaneously via complete, thorough training. A task and skill analysts was executed for shuttle cars, continuous miners, cutters, loaders, face drills, tractors, and scoops. The prototype training system is for shuttle car operator training.

Jan 1, 1976

By John Griffen

DURING the past year, purchases of coal-preparation equipment and the discussions and plant-scale tests conducted indicate that much attention is being given to better recoveries of coal by preparation plants and improved quality of the finer sizes to widen their market. In the anthracite regions the new equipment was predominantly for the cleaning of the steam sizes, much of it for treating No. 4 and No. 5 buckwheat. The units installed were largely coal-washing tables, Hydrotators, and Menzies cone separators.

Jan 1, 1944

By C. J. Newman, K. Molnar, A. G. Storey, G. Macfarlane

"The Kidd Creek copper smelter started operation in June 1981 using the Mitsubishi Continuous Smelting Process. A steady increase in plant production rates has been demonstrated, and the annual tonnage of concentrate smelted is now double the original design rate. This paper summarizes recent modifications made to increase concentrate feed rates, increase on-line time, reduce copper losses and control the impurity level in anode copper. It includes improvements made to furnace design, improvements to reduce downtime f or boiler cleaning, and improvements made to the acid plant to allow handling of increased gas flowrates and higher gas strengths while maintaining low acid plant emission rates. IntroductionThe Kidd Creek Division of Fal conbridge Limited operates a base-metal mining and metallurgical complex, located in Timmins, Ontario, which includes an underground mine, a 13 500 tonne/day concentrator, a 130000 tonne/year zinc plant and a copper smelter and refinery, The copper smelter and refinery were commissioned in 1981, with an installed capacity of 59 000 tonnes/ year of cathode. The smelter, utilizing the continuous smelting technology of the Mitsubishi Process, has subsequently been expanded in production capacity, and in 1991 produced 113 500 tonnes of blister copper The capacity of the refinery, which uses Onahama No. 3 tankhouse technology, has been increased to 96 000 tonnes/year of cathode. The capacity increase at the smelter has been realized through the input of additional oxygen to both the smelting and converting furnaces, without increasing the process off-gas flowrate through the associated waste heat boilers.In this paper, a brief review of smelter operation and modifications in the period 1982 to 1987 is presented, together with a more detailed discussion of operation during 1988 to 1991, and a discussion of future planned improvements."

Jan 1, 1992

By M. E. C. Snyman, N. Naudé

"Coal fines produced during processing are difficult to dewater and result in a lower quality product and consequent lower value. A South African coal mine experiences severe difficulties with belt filter dewatering operations due to the presence of fines reporting from the thickener underflows. Plant 2 currently handles super-fine particles of size -34 µm and has low belt filter efficiency: excessive moisture retention lowers the product quality and strains downstream processing. It was necessary to determine an alternative method for dewatering these fines. Blending of fine material with coarser material was proposed as a solution. The effect of coal particle size and layering during ultrafines belt filter dewatering was evaluated using various blends of the fine Plant 2 material with coarser Plant 1 material. The best layering arrangement of the two materials and its optimum blend required to achieve reduced filter cake moisture content was determined in practise using a vacuum filter to simulate belt filtration. A blend of the two materials gave improved dewatering efficiency for the belt filters compared with that of the Plant 2 material alone. The best layering configuration was with Plant 2 material at the bottom and Plant 1 material on top. The optimum blend for industrial applications comprised 48% fines from Plant 2. IntroductionFines are produced during the processing of coal. It is estimated that 2 to 3% of run-ofmine coal reports to the ultrafine portion (-100 µm) (le Roux, 2005). The particle size of coal is inversely proportional to the amount of water adsorption, so smaller particles adsorb more moisture. Moisture removal requires either mechanical processes or thermal drying: mechanical processes are less expensive, but the fines still have high moisture retention. Discarding of fines leads to economic losses, so it is essential that they be dewatered so that they can then be sold as a product: fines need to be treated for both resource management and conservation reasons (Kenney, 1994). Removal of free surface moisture from ultrafine coal particles using a belt filter therefore remains a process that needs to be continuously improved. Ultrafine coal originating from a thickener underflow is known to be difficult to dewater owing to factors such as filter cloth blockage and moisture retention due to clogging. Mixing of finer and coarser materials has been proposed to deliver better dewatering efficiency and improved the quality of the recycled water (Kenney, 1994)."

Mar 1, 2019

By F. J. Longworth

FoR a number of years an intensive study has been made to improve the blast-furnace practice at Copperhill not only as to cost% but to provide a good grade of gas for the acid plants. This study took us back to the fundamentals of successful pyrite smelting; namely, a blast furnace working on a clean sulfide ore, free from fines, and the use of quartz high in silica as a flux. In 1919, the quality of the flux was improved and its effect on the metallurgy was very marked. To improve the practice further, it was necessary to work out some method of treatment for the sulfide fines and the siliceous and refractory ores, other than in the blast furnace. A series of milling tests indicated that these products could be successfully treated by differential flotation, and in 1922 plans were made and a flotation plant built. It was estimated that the flotation plant would deliver to the smelter 40 to 50 tons of concentrates per day; the problem was what to do with these concentrates. It was out of the question to attempt to smelt them in a blast furnace because of the dust losses and because our practice demands a charge free from fines for satisfactory operation. There is no custom smelter in the vicinity to which concentrates may be sold, pending the time when the tonnage will be sufficient to warrant roasters and a reverbatory furnace. Sintering and nodulizing were investigated but neither method fitted into our scheme of metallurgy. A close study of the converter practice was then made to see if some method could not be evolved to smelt this tonnage of concentrates in a converter without preliminary treatment. At that time, the converter installation consisted of two 12-ft. Great Falls converters, which were handling 12 to 14 per cent. matte. The heat balance of the converters working with 12 to 14 per cent. matte was more than sufficient to smelt the contemplated tonnage of concentrates but the mechanical difficulties of feeding fines into the Great Falls converter made the use of this type of converter impractical. While there was no opportunity to experiment with the Pierce-Smith converter, equipped with a Garr gun, theoretically it seemed practical

Jan 1, 1925

By K. Norris

"The Campbell mill has undergone numerous changes over the past 43 years. However the rate of change has increased significantly in the last 4 years. A new grinding circuit, carbon-in- pulp circuit, pressure oxidation plant, and column flotation circuit are all new additions. Other changes have occurred in the last 2 years including a large reduction in sodium cyanide consumption, and the introduction of a computer controlled grinding circuit. More improvements are planned in the next 2 years. Some of these improvements include the construction of an effluent treatment plant, and the replacement of filtering and Merrill-Crowe precipitation with carbon-in-leach and electrowinning.Recent changes and improvements to the Campbell mill are a commitment by Campbell mill personnel and Placer Dome Inc. to decrease operating costs, increase gold recovery and gold production, improve industrial hygiene and safety, and meet environmental compliance with current government legislation.INTRODUCTIONThe Campbell Mine has been and continues to be one of Canada's premier gold mines. Campbell Mine is 100% owned and operated by Placer Dome Incorporated. Milling of ore commenced in 1949 at a rate of 300 tons/day producing 58,000 ounces per year of gold. In 1992 Campbell Mine will mill 1340 tons/day of ore at a grade of 0.6 ounces/ton, producing 275,000 ounces of gold at a cash cost of $205.00 Cdn./ounce.This paper discusses some of the changes that have been made to the Campbell mill in the past 4 years. The flowsheet has undergone extensive changes and will continue to change rapidly in the next 2 to 3 years. A simplified flowsheet of the Campbell mill is shown in figure 1."

Jan 1, 1992

By Frank A. Vonesh

In order to reduce the amount of visible, airborne emissions in the Metals Industry, a new Industrial Gas Technology was developed by Air Liquide. This patented technique is called ALECT?, Air Liquide Emission Control Technology. Demonstrations have been conducted for many cutting and lancing operations as well as for hot metal transfer from vessel to vessel. Fume reductions of 90% and greater have been achieved in actual practice. Air Liquide continues to improve the process and the associated control equipment.

Jan 1, 1994

By David Forrester

Subsidence beneath the land surface has traditionally been monitored using the most accurate surveying methods of the day. Over the several hundred years of subsidence investigation, these techniques have improved, and thus the accuracy of subsidence measurements has improved. In circumstances where the subsiding surface is masked by water or rock, novel methods must be developed. This method describes the recent successes of subsidence monitoring using advanced bathymeric techniques in the Sydney Coalfield. In order to obtain subsidence profiles above submarine coal extractions, seafloor bathymetry surveys, run before and after mining, have shown that subsidence profiles can be detected, despite the primitive nature of some of the trials. Very recently, there have been considerable advances in this field, associated with the availablity of high-powered personal computers to control data collection and analyse the results. The recent surveys described in this paper have demonstrated the considerable potential for such methods. This paper describes bathymetric subsidence monitoring developed in the Sydney Coalfield, illustrated with some typical results, and summarizes the findings of the research leading to the development of subsidence design criteria specific to the Sydney Coalfield.

Jan 1, 1996