Search Documents

By J. A. Herbst

In spite of potential theoretical and economic advantages of large-diameter ball mills, many manufacturers elect not to build these mills owing to what is perceived as an excessively large design risk. This risk results from the fact that traditional predictions for mill-scale-up to large diameters are not always accurate. It is apparent that alternative methods of analysis and scale-up are required. Recent studies have shown that detailed population balance models which account for important grinding subprocesses, i.e., grinding kinetics, material transport, and classification, are capable of predicting the performance of small- and intermediate diameter mills (up to 4.3 m (14 ft)) from small-scale batch tests. These same models are used in the current study to predict the performance of a "borderline" large ball mill (4.7x5.5 m) at Asarco's Sacaton operation, a ball mill (5.0x5.8 m) at Kennecott's Chino operation, and one of the world's largest ball mills (5.5x6.1 m), at Cities Service Pinto Valley operation. Model parameters required for scale-up have been estimated in a 380-mm diameter batch mill. Predictions are compared with the results of detailed plant sampling in the three plants. For the Sacaton and Chino operations, the error of the predictions was found to be less than 2.5%, while the corresponding error for the Pinto Valley operation was less than 2.7%. It is concluded that proper representation of the major subprocesses of grinding in the model equation is the key to achieving accurate scale-up. Of special importance is the need to account for the size distribution of the grinding media and the influence of the size distribution environment in the mill on grinding kinetics.

Jan 1, 1983

By Myles G. Hyams

A mining project is proposed for the state of Pahang, Malaysia. The proposal involves the mining of a sulphidic ore body and initial processing to form a sulphide concentrate which will be transported to a roaster/acid plant for the production of sulphuric acid. An outline is presented on the potential environmental impacts of the project which have been assessed by superimposing project infrastructure and processes on to the physical, biological and social environment during the early design and planning stage of the project. The potential impacts eliminated by engineering design and the techniques employed are presented. However, there are a number of potential impacts that require careful consideration and planning for long term management. These include surface water drainage, waste rock leachate, tailings disposal and the social environment. Environmental management designed to minimise or alleviate these impacts as a result of project implementation concludes the paper.

Jan 1, 1991

By Jürgen Antrekowitsch, Harald Osthof, Stefan Steinlechner

"In the case of feasibility assessments or feasibility studies, an important point of discussion is often how to calculate the capital (CAPEX) and operating expenditure (OPEX) of a plant. Generally, there is also the request to know how the CAPEX varies when the size of the plant is increased. Nowadays, many databases give an indication of specific equipment costs in relation to the production rate. These data are based on cost information from equipment suppliers and have to be continuously updated by the owner of the database. The approach presented here is a model which allows sizing of process equipment, for example a leach tank, based on process data in combination with the calculation of mechanical properties. Furthermore, it calculates the CAPEX based on construction material cost and adequate machining surcharges. Thus, a single cost model for a leach tank is adequate for both copper and other hydrometallurgical plants and stays valid with changing construction material prices. To summarize, the advantage of this model is the more versatile approach and thus the flexibility due to the inclusion of design aspects, process and mechanical engineering aspects and an updatable database. The database, which is in regard to material cost and is the basis for the cost estimation, is easily updatable from commonly accessible data. This model thus approaches the procedures of an engineering company when designing a plant and executing a cost calculation. INTRODUCTION Hydrometallurgy nowadays plays an important role in processing of primary and secondary resources. In copper metallurgy, hydrometallurgy accounts for roughly 20 % of worldwide primary production, especially in the case of oxide or low copper-containing ores. Zinc smelters changed their method of production from a pyrometallurgical-dominated concept decades ago to mainly hydrometallurgical routes today. Gold production processes using leaching, especially, have a long history without any development which would not be competitive if not based on hydrometallurgical concepts (Pawlek, 1983; Winnacker-Küchler, 2006)."

Jan 1, 2015

By G W. Wilson

Rehabilitation of tailings impoundments is one of the most challenging aspects in mine closure, as not only does the potential for producing leachate pose a challenge to the rehabilitation designer, but also other aspects such as stability and settlement must be considered. The water balance of a tailings impoundment is unique in the sense that it usually hosts a pond that in turn causes a phreatic surface in the impoundment. The position of the phreatic surface defines the saturated and unsaturated zones in the impoundment, which of course varies spatially and temporally. Predictive modelling for this hydrologic system becomes difficult, as numerical models capable of analysing the combined saturated/unsaturated zones are not adequately refined to accurately solve the flux boundary problem for infiltration at the surface of the tailings. This paper describes the development of a flux boundary model that enabled accurate modelling of the unsaturated zone in the tailings impoundment at Kidston Gold Mine, Queensland, Australia. The technique made it possible to accurately predict the spatial variation of infiltration to the tailings as a result of the presence of the phreatic table. The conceptual model defines the boundaries for the Kidston tailings dam, based on a generalised cross-section through the dam. Firstly the shape of the top boundary is described as a function of the particle size of the tailings associated with particle segregation that occurs due to the hydraulic placement of tailings. This function was rigorously tested using in situ infiltration tests and laboratory materials testing. Defining the bottom boundary of the section, ie the phreatic level was done by physically monitoring the phreatic level with 42 piezometers strategically located on the tailings dam. Analysis of this data led to the fixing of this bottom boundary through the introduction of a function that mimicked the shape of the phreatic level. The material properties of the surface layer, specifically the saturated permeability that would govern the infiltration/exfiltration rates of moisture through the top boundary layer were defined on the basis of extensive field and laboratory material testing. A function for the saturated permeability was developed on the principles of particle segregation. Finally a procedure is described for the application of the new conceptual model for the evaluation of the spatial infiltration to a tailings surface using the rigorous one dimensional surface flux boundary code SoilCover. The solution of the calculation described above was then used as the top boundary condition in conventional three dimensional saturated/ unsaturated flow codes, and verified against measured seepage rates from the tailings impoundment under drains. It was concluded that the developed spatial flux function was in deed a most rigorous representation of reality. Although the methodology presented here was applied to the Kidston tailings impoundment only, the authors believe that the principles are directly transferable to any tailings impoundment that has a varying phreatic zone thickness due to the presence of a pond. The mathematical equations describing the typical cross-section would be site specific, but the approach and ultimate solution methodology would be directly transferable.

Jan 1, 2003

By Matthew Preedy, Anthony Pooley, Mike Wongkaew, Dirk Bakker, Raghu Bhargava

Sound Transit’s ST3 program will add 62 miles of light rail to the Puget Sound area, including connections to the neighborhoods of West Seattle currently anticipated by 2031 and Ballard by 2036. These connections include considerations for both elevated and tunnel alternatives, as well as a new downtown tunnel for which different configurations are being considered with potentially very different construction logistics and risk profiles. This paper describes the latest developments in the ongoing evaluation process that will inform the consideration of different tunnel and station construction methods, technical and operational challenges and contracting methodologies, including construction of deep stations in dense urban environments.

Jun 13, 2021

By O. E. Polter, W. J. N. Fernando

Smelter-grade alumina is usually produced by the calcination of gibbsite. The ideal energy requirements for the calcination of gibbsite have been analysed and compared with the actual energy consumption of some industrial calcination processes. The consumption of most of these is considerably in excess of the ideal. Methods suggested for calcining dry gibbsite feeds which claim energy savings of 10-14% consume 26-34% more than the ideal energy requirement for dry feeds. This study indicates that it should be possible to recover appreciably more energy, giving further improvements in fuel efficiency, both in existing gibbsite calcination processes and in methods that have been proposed for the stagewise calcination of dry gibbsite

Jun 13, 1905

By R. R. Tatiya

The selection of a mining method for a particular deposit must be based on certain technical and economic criteria. This can be interpreted as maximizing extraction and productivity while maintaining safe working conditions and minimum costs. The methodology developed here examines some of these aspects. The proposed methodology was tested on copper deposits that could be mined by underground stoping methods such as sublevel stoping, cut-and-fill stoping and their variants. In general, it provides a practical approach to both method selection and optimum stope design for base-metal deposits.

Jan 1, 1998

By Sukumar Bandopadhyay

In recent years, research in the field of artificial intelligence (AI) has had many important successes. Among the most significant of these has been the development of powerful new computer software known as the "expert systems". Expert system programs designed to provide expert-level consultative advice in mineral exploration (Duda et al, 1981), scientific (Feigenbaum, Buchanan and Lederburg, 1971) and medical (Shortliffe, 1976) problem solving are generally acknowledged to be among the forerunners of this research. As the decision makers virtually in all fields face a more complex and involved world within which to operate, the need for some decision support is also becoming urgent. Thus applications of expert systems continue to spread out reaching problems that, because of their dimensions or particular aspects, set more demand on the decision methodologies. To meet these new requirements, many activities which were performed in the past by the domain expert or engineer must become automated. Furthermore, previous research (Dawes and Corrigan, 1974; Dawes, 1979) has shown that automating an expert's decision rules often provide better decision than the expert does. For large systems it would be very useful (or even necessary) to have formal tools, allowing one for example, to automatically discover inconsistencies, contradictions or redundancies, or to identify the possibilities of wrong lines of reasoning in the decision process.

Jan 1, 1990

THERE are many kinds and varieties of earth* that are used for the loam compositions for making the moulds for casting bronze, brass, or other metals. Since this is a very necessary thing, you must try to have the best kind and one that resists the fire well. It must be disposed to receive the metals well, must make a neat casting, and must not shrink or break with cracks on drying or baking. Aside from actual trial, I believe that there is little that can help you, since the clay in itself has no color or [77] visible sign that I know of to show how satisfactory it is. Understand that their colors are no less varied than their natures, for, as you see, one is white, one black, one yellow, and another red. Perhaps none will show by its color that it is good for this work, yet it might also happen that all colors are good. But all that I can say about it is to show you by their effects how the good ones should be in their nature; and so by trial you will choose among those that come into your hands. All earths are either sandy or tufaceous, either argillaceous and lean or pasty with unctuous viscosity. The lean ones make the loam powdery and without toughness and hold together poorly by themselves when they are dry. The unctuous and viscous ones shrink and break. Becoming smaller by shrinking, they often twist the forms and they stick together badly. They swell up again in the fire and produce works that are neither exact-a nor neat. Therefore, the good ones must be those that are neither unctuous nor lean, neither wholly tender nor rough, and with a grain that is fine, without pebbles or shells. When applied to a work they easily dry out without fractures and, when dry, hold their own shape well. Above all they must resist the fire well. These are usually of a yellow or red color, but whatever their color may be, the color does not force me to say that the yellow are really better than the black, and the red than the white or gray. Their quality depends on what trial shows. Thus, to summarize, whenever you have to do this work, you must try to have the best clay that you can, because it is to be the foundation of

Jan 1, 1942

By Jacek Paraszczak

As the deposits located closer to the surface are getting depleted, more and more Canadian mines produce ore from considerable depths. Deep mining represents a number of serious challenges including high rock temperature. Conventional diesel powered loadhaul- dump machines and trucks so widely used in metal mines constitute an additional source of heat and noxious gases. Due to this, they have a substantial adverse impact on a quantity of fresh air required and a cost of ventilation, particularly since the mines have to meet more and more stringent regulations in this respect. In this context, the paper examines possible alternatives for diesel powered equipment, both these commercially available as those at the stages of prototypes or under development. They are reviewed with regards to their principles, required infrastructure, stage of technology development and its progress. The questions of their flexibility, practicality and economic viability are also addressed. Following the above a potential for their implementation and possible benefits (if any) in the conditions of deep Canadian mines is discussed. The paper concludes with short to medium term predictions concerning the most promising drive alternatives for vehicles destined to operate in deep metal mines.

Feb 1, 2008

The Bureau of Mines is responsible for a broad spectrum of programs for meeting the diverse and changing mineral resource needs of the Nation. These programs are managed by the Director and two Deputy Directors, who formulate general policy and program direction from the Washington, D.C., headquarters. A senior advisory staff, consisting of the Chief Staff Officer, Chief Scientist, and Chief Mining Engineer, provides advice and consultation to the Director on a wide range of scientific and technical matters and acts on behalf of the Director to maintain liaisons with other government agencies, mineral industries, and professional societies. Bureau program activities are classified into two major functions: (1) Developing new and improved technology that will make the production and processing of minerals more efficient, safer and more healthful for mineral workers and the public, and more compatible with a quality environment.

Jan 1, 1980

By T. A. Postolski, A. J. Sinclair

"Abstract- Two examples are used to describe how geological features impact on the development of semi-variogram models to be used for geostatistical resource/reserve estimation of porphyry-type deposits. In the Main zone of the Huckleberry porphyry copper deposit, mineralization is concentrated in fracture zones localized in volcanic rocks, along the eastern and southern margins of a granitic stock. Mineralized volcanic rocks can be subdivided into three separate domains, each with its own preferred direction of mineralization that is reflected in contoured Cu diagrams and semivariograms.The East zone at Huckleberry deposit, spatially distinct from the Main zone, is controlled by a fracture zone elongate roughly east-westerly and bounded on the south by a major fault (easterly striking and steeply dipping) across which there is a dramatic drop in grades. The eastern part of the East zone appears to be coaxial with a large intrusive body; the western part contains a small, elongate dike-like intrusion. Contoured Cu values for many levels suggest that the principal direction of geological elongation of the east and west domains of the East zone differs significantly. Independently derived semi-variogram models for each domain are different and reflect this difference in trend.In both Main and East zones of the Huckleberry deposit, block estimates by ordinary kriging are significantly different using a domain-specific semi-variogram model than using a deposit-general semi-variogram model. The domain-specific estimates are deemed better because they are based on local controls of mineralization and have less conditional bias than those generated by the depositgeneral semi-variogram model."

Jan 1, 1998

By F. A. Penning

Improved skips, with lightweight cylindrical bodies, have made a significant contribution to advancing mine hoisting technology. New concept skips of aluminum bodies with rubber lining; fiberglas bodies with polyurethane liners have been designed and fabricated for field testing at an operating mine. New design, adjustable guide rollers have shown improved ride characteristics with noticeably less wear. Major reductions have been made in stress levels and stress concentrations. Field experience has shown the practicality of the approach. Guide alignment has been measured using the Guide Alignment Measuring System (GAMS). Analysis has been applied to interpret the data. Field measurements in an operating shaft and a test tower have shown the agreement in data from GAMS and plumb wires. Reproducibility has been demonstrated. The data are useful to realign shafts, to use as s maintenance tool, and to evaluate the maximum safe hoisting speeds. The surveys are made at several hundred feet per minute and the system is self-contained. Dynamics of skip-guide interaction has been analyzed using the computer program SKIP II. The effects of speed, weight, type of guides, kind of misalignment have been studied. Resonance has been demonstrated and factors that eliminate resonance have been identified. Data from the GAMS surveys are applicable to the SKIP II program. Interaction between the hoist rope and the mine conveyance has also been studied. Computer programs and closed-form solutions are presented. Economic impact of lightweight skips is presented for an existing mine and for a new mine. Reduction in rope size has a profound effect when using a lightweight skip for the same capacity. Increased productivity can be realized by keeping maximum rope pull the same while increasing skip capacity. Examples and charts project the significant savings in capital expenditure for new installations.

Jan 1, 1985

By LaPoint D. J.

Copper deposits in sandstones are excellent targets for open pit mines using SX-EW extraction and processing methods. The mineralogy consists of chalcocite as the primary sulfide and copper carbonates and sulfates in the zone of oxidation. Two general deposit types are recognized: early diagenetic copper deposits that are associated with the reddening of the surrounding sediments, and epigenetic deposits that are associated with the migration of copper-rich basinal fluids along faults into permeable reservoir beds with a source of reductant. Epigenetic copper deposits are more likely to contain enough tonnage to be economic.

Jan 1, 1996

The mining industry continues to experience a skills shortage and this is having an impact on the ability of mining companies to operate sustainably. Apart from a few exceptions, there is a dearth of geologists, mining engineers, metallurgists as well as environmental scientists and other professionals in the global mining industry. This relates to both quantity and quality. It makes good business sense for mining companies to employ local professionals rather than expensive expatriate staff. In some cases a mining company could employ more than 10 local mining engineers for the cost of one expatriate. However, in many countries local professionals are not always equipped professionally to work on mine sites. The result is that many companies are not operated optimally due to human resources gaps. In some cases, particularly in key areas such as mine planning, this threatens the sustainability of the operation or at the very least results in sub-optimal resource utilisation. This paper briefly presents some of the issues and strategies being implemented and that might be implemented to maintain a sustainable supply of quality minerals graduates to the industry in 2011 and beyond.

Jan 1, 2011

By Maurice Deul

Limestone can be used effectively in treating acid mine water. Aside from a lower cost than for other treatment agents, limestone has the advantages of easy storage and effectiveness even when impure and in slack sizes. Limestone incorporated into waste piles in layers or as riprap can inhibit acid formation; limestone rubble packed in a mine entry offers promise in formation of a low-cost autogenous resilient seal.

Jan 1, 1974

By Nicholas Kyriazi

Significant portions of the present Federal regulations for certification of closed-circuit breathing apparatus (42 CFR 84) are not quantitative. The human-subject testing portion of the regulations specifies activities rather than metabolic work rates; however, heavy human subjects have higher oxygen consumption, CO2 production, and ventilation rates than lighter human subjects performing the same activities. This means that apparatus certified using different human subjects have effectively passed different tests. In addition, apparatus performance is monitored only during selected intervals of testing, and always during rest, rather than during the entire performance period. Further, testing is arbitrarily terminated at specific rated durations, leaving unknown the performance during the remaining duration. Duration itself is misleading to users who believe that the apparatus will last a certain time no matter how much they weigh or how hard they work. The actual duration obtained from an apparatus, however, is highly variable, being inversely proportional to the work rate at which it is used. In this report, recommendations are made to (1) replace the present regulations for certification of closed-circuit breathing apparatus with quantitative tests specifying metabolic work rate rather than activity,(2) continuously monitor relevant physiological stressors, (3) continue testing until exhaustion of the oxygen source, and (4) classify closed-circuit breathing apparatus by quantity of usable oxygen, i.e., capacity, rather than by duration. Physiology-based stressor levels are suggested as well.

Jan 1, 1999

Upon subduction, water is liberated from the sediments and the porous struc- ture of the oceanic crust and from de- hydration of minerals for redistribution and chemical reaction. A survey of pro- cesses which are likely to occur along the subducting plate reveals that water may well be basic in subduction induced gas generation, magma formation and ore deposition. In analogy to the industrial water gas process, reaction of water with car- bonaceous matter, in subducted sediments is likely to yield substantial volumes of hydrogen and carbon dioxide. While water and carbon dioxide appear to play a determining role in the development of differentiated magmas, hydrogen will react with metal sulfides and sulfur to form hydrogen sulfide which is essential in sulfide ore depo- sition. A survey of possible metal extrac- tion chemistry along subduction suggests a stepwise solubilization of metals from sediments and oceanic crust, and a poten tial accumulation of dissolved metals in zones of characteristic composition. The metal spectrum in ore deposits at near surface appears to reflect the com- position of the solution in the respec- tive subduction zone. A tendency for preferential solubi- lization of copper at subductidn level, from among the transition metals, an in- creasing generation of hydrogen sulfide in the sane direction and partition effects as well as sulfide precipitation characteristics lead to enrichment in copper and to its selective deposition in the direction towards the trench as observed in S. Latin America. A postscript deals with the formation of native copper.

Jan 1, 1986

By J. I. Paige, T. T. Campbell, A. W. Henderson, H. M. Harris

The chlorination of ilmenite concentrates and slags to produce Tic14 suitable for pigment or metal production was investigated by the Bureau of Mines along with the dechlorination of byproduct iron chloride to produce chlorine for recycle and iron oxide., Ilmenite concentrates or slag powders were fed into the bottom of a fluidized coke bed at 1,050º C using chlorine flow rates up to 20 l/min in a 10.2-cm-dim reactor. Tests showed that >95 percent of the various ilmenite concentrates reacted at optimum conditions, and recovery of TiC14 ranged from 95 to 100 percent of stoichiometric. Impurity dusts were removed from the vapors by cyclones and a fiberglass cloth filter. Iron chloride was condensed as a powder with less than 0.4 percent insoluble material. The TiC14 was collected in refrigerated condensers. Iron chloride was dechlorinated at 500º to 550º C by reaction with oxygen in a 16.5-cm-dim reactor using a fluidized bed of Fe2O3. Optimum processing was attained with a FeC13 feed containing 25 wt-pct Fe203 granules treated with 2 wt-pct NaCl catalyst; Under the above conditions, off gas chlorine concentrations of 62 to 90 wt-pct were obtained. During 2- and 3-day tests with technical-grade FeC13, conversion of FeC13 was 94 to 97 percent, chlorine concentrations were 76 to 90 wt-pct, and up to 92 pct of the stoichio- metric Fe203 was removed in the primary reactor discharge. Chlorine

Jan 1, 1976

The key concepts relating to the calculation of recoverable reserves for selective mining in open pit gold operations are discussed. While the general concepts are relevant to a wide range of gold ore bodies, their application is specific to particular ore bodies.The important factors contributing to the recoverable reserves aregeology, mining method, dilution, ore loss, sampling methods and theultimate bench height used in production.The implications of current methods of computing recoverable reservesare reviewed and some alternative approaches to recoverable reservecomputation based on production experience are presented.

Jan 1, 1986