Search Documents

A four monthly period was analysed for each retreating longwall face which indicated that output increased from 1140 tonnes/day for Longwall 1, to 1620 tonnes/day for Longwall 2 and to 2090 tonnes/day for Longwall 3. An output of 2500 tonnes/day should be achieved from the new Longwall 4, largely due to the improved tailgate corner design and despite a continuing lump coal problem. The evolutionary trend is a feature of longwall mining; the evolution occurring both with mining and mechanical design at the colliery itself and with the longwall equipment offered by manufacturers. The trend is towards simplicity, increased strength and capacity, simplified maintenance and increase relia- bility.

Jan 1, 1976

By K. Taylor

In surface coal mining, the performance of a shovel through blasted muck is one of the key performance indicators of the blast. Historically, performance has been measured qualitatively based on operator feedback or visuals of the muckpile. More complete shovel data, such as loading times and GPS location, is available from most fleet dispatch systems that are already in place at most truck and shovel operations. With some database and analysis skill, the drill and blast team can take advantage of this data to make targeted improvements to drill and blast designs. An area typically known to cause trouble for shovel operators at this operation are blast boundaries. Blast patterns with and without design changes along the boundaries were studied in this case study. The instantaneous loading times for each shovel pass were analyzed for 75 blasts across two subsequent benches with similar firing direction and shovel paths. The benches were split into three categories: Main body of pattern, boundary with design change, and boundary with no design change. The loading times from the main body of the patterns and where the design change was utilized in the boundary had similar prevalence of good loading times. However, boundary areas without the deign change had approximately 2% more prevalence of poor loading times compared to the main boundary of the pattern. Improving the dig rates through the boundaries up to the average loading time would result in approximately 280 hours taken off the total loading time for one bench. By quantifying the shovel’s performance by GPS location, the drill and blast team can decide how much of a design change is needed, can target precisely only the areas that require it and measure the impact of any changes made

Jan 1, 2024

The process of hydraulic transport through pipelines, world-wide well known for the trans- port of fine-grain solids is also being used to a greater extent in mining for the handling of 1rimarily coarse-grain solid - water mixtures r the removal of, for instance Coal and waste mixtures after coal winning rising hydraulic monitors, lings for backfilling underground and :her tailings and flotation waste to A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining P',search Company) in Essen-Kray, GFR, to ¦urther improve this technology. The unit was :fanned and built by Krupp Industrie- and +hibau of Duisburg in cooperation with i r

Jan 1, 1980

The theme of the conference is "excellence", an epithet of special significance in tertiary education. It appears in the mission statements, goals and plans to achieve them of most, and quite possibly all, tertiary institutions in Australia. In the context of excellence, this paper examines the current statue of professional education in the principal mining industry related discipline of Mining Engineering. It furthermore, identifies and discusses a number of special problems in mining education that the tertiary sector has long endured. Some of these problems are becoming acute, and solutions will have to be found soon in order for the industry to be assured of the supply of well motivated and appropriately qualified young engineers and scientists necessary to achieve and maintain the excellent to which it aspires.

Jan 1, 1989

By David Bequette, Ray D. Peterson, Cynthia K. Belt

"With a need to cut production costs in the metals industry, cost savings from energy efficiency improvements are critical. Opportunities can be found by reviewing furnace systems and practices so that the melting and holding processes operate at the highest energy efficiency. Many of the changes can be implemented with a minimum of expense or capital investment. This paper will review several low cost methods to optimize energy efficiency on reverberatory melting or holding furnaces. These five methods (furnace utilization, idle procedures, fire rate, controls, furnace pressure) will be explained and information given to implement these changes. Included are several rules-of-thumb and benchmarks for aluminum reverb furnaces.IntroductionEnergy can be a significant portion of the total manufacturing costs for metals and materials manufacturing involving thermal processing such as heat treating, melting, and high temperature processing. Natural gas prices have dramatically varied over the last few years. While no one can foresee the future, prices are expected to increase from the current low prices. More recently, emphasis is being put on the reduction of greenhouse gases with the potential of additional costs to industry.One of the first steps in an energy management program is to measure the energy usage of the process [1]. The results are typically understood in relation to the mass melted in kWh / mT [BTU / lb]. For the purposes of this paper, furnace energy efficiency is calculated over a month or even a year and thus includes hold times. This efficiency is typically different from the values quoted by furnace manufacturers. Those values are for limited short term tests at highutilization.Once you know the performance for your furnaces, these should be compared to industry benchmarks. For aluminum melt furnaces with cold air burner systems, a benchmark value or goal is 1800-2000 BTU/lb [1160-1290 kWh/mt], though some of the best have reached 1600 BTU/lb [1030 kWh/mt]. Furnaces with regenerative burners can attain 1100-1200 BTU/lb [710- 775 kWh/mt]. There are some designs of multi-chamber furnaces or oxygen furnaces that have improved on these numbers, perhaps as low as 950 BTU/lb [615 kWh/mt]. Typically, as the degree of sophistication and energy efficiency of the furnace increases, so does the cost."

Jan 1, 2010

By M Astorga, J Jackson, J Gaunt

The Ban Houayxai mine (BHX) is a relatively low-grade, low-cost, open pit gold-silver deposit in Laos operated by Phu Bia Mining, a subsidiary of PanAust. The ore production rate at BHX is 4.5 Mt/a, with direct tipping to a semi-autogenous grinding/ball mill circuit with a carbon-in-leach process plant. Approximately 100 000 oz of gold is produced per annum.The operation is located in mountainous terrain with minimal run-of-mine stockpiling. This results in limited capacity for blending from stockpile, with the mill instead reliant upon direct feed ex-pit. Since commissioning in 2012, the plant has seen significant variation in milling rates due to variability in the feed properties of the oxide, transition and primary ores. As part of an ongoing continuous improvement program, an integrated approach was initiated, focusing on maintaining and enhancing production in the future as the proportion of harder primary ore increases. This will specifically focus on direct blending from the loading face using the ore properties and blast fragmentation to maintain mill throughput.This approach was based on the concept of physical assets management, commencing with improving information and knowledge of the condition of the orebody through modelling the characteristics, variability and performance of the feed for processes relevant to throughput. These models are used to support both mine and process plant production planning.The key ore feed characteristics and parameters modelled for the life-of-mine are blastability index, powder factor, crushability or impact resistance and grindability. These predictive spatial models were based on the data from diamond drill holes used in resource definition and geotechnical drilling programs by integrating geotechnical, geological, geochemical and metallurgical data.At the early stages of implementation, the models are being utilised for ore blending decisions to provide guidance and support for budgeting, long-term mine planning, blast design for mill feed and providing the mill with an expectation of performance.CITATION:Jackson, J, Gaunt, J and Astorga, M, 2014. Predicting mill ore feed variability using integrated geotechnical/geometallurgical models, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 165–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By P Toor

Due to the high energy consumption of milling, it is desirable to improve the efficiency of this process. One alternative to reduce energy and material consumption while optimising production yield in mill operation is through balanced design and selection of liners. Over-design of liners leads to increased life but at a cost to grinding performance, a relationship which to date has not been studied closely. This paper provides a description of this process of liner life cycle optimization and presents initial results from the first of two life cycles being studied for a 32 foot (ft) SAG mill. The use of commercially proven high resolution laser scanning based liner shape information provided by the MillMapper® software correlated with well controlled site surveys at various points in the liner life was used as the basis for comparison. The survey data was modelled in JKSimMet to provide direct comparisons of mill performance. This potentially provides a methodology for the design of liners that maintain a favourable shape for the majority of liner life, yielding desirable production parameters such as lower specific energy consumption and higher throughput, while at the same time maintaining practical liner life cycles.

Aug 8, 2011

By Y. Luo

"It is generally known that spontaneous combustion potential is a function of coal rank, with low-rank coals having high susceptibility to self-ignition and high-rank coals having low potential. To establish this functional relationship and use it as an engineering tool to identify the propensity of coal to self-heat, both rank and spontaneous combustion potential should be quantified. ASTM D388 is normally used to classify coals by rank, but this classification system can only serve a qualitative analysis. To classify coals by their potential for spontaneous combustion, the self-heating temperature (SHT) method originally developed by the U.S. Bureau of Mines (USBM) was used by Litton and Page (1994) to correlate coal rank with spontaneous combustion potential. In that method, the SHTs of coal determined by an adiabatic experiment are linked with proximate analysis results through a proposed concept known as the “moist fuel ratio.” This ratio is a function of moisture, volatile matter and fixed carbon, all of which have widely different content percentages in different ranks of coal and have strong relationships with coal rank. However, the method is highly empirical, and there is large standard deviation between experimental data and calculated results. The equation correlating the coal quality parameters to determine SHT should be improved with more experimental data.This paper reports on the development of a new system for predicting the spontaneous combustion potential of U.S. coals, based on coal composition data from the U.S. Geological Survey’s coal quality database. First, the user is provided with a quantified classification of coal rank. Second, based on experimental SHT data covering a wide range of ranks from lignite to low-volatile bituminous coal, the original USBM correlation for predicting SHT is improved for the respective rank of coal. The relationship between the rank and SHT of U.S. coals was developed and plotted. The plot diagram can be used for a quick estimate of the SHT of a U.S. coal and as a cost-effective tool for the initial risk assessment of a new mine development."

Jan 1, 2015

By K Jupp, T J. Howard

Cliffs Natural Resources Pty Ltd (CNR) operates iron ore mines in the Koolyanobbing region of Western Australia. Ore is mined from three locations, separated by many kilometres. The ore is stockpiled at these locations, according to an in-house ore classification system (based on grade and source) and then trucked to the crushing and screening plant at Koolyanobbing. Lump and fines products are railed to Esperance for ship loading and export to Asian customers. CNR prides itself on the relatively low inter-shipment grade variability of the products. The Koolyanobbing crusher is fed using a daily blend plan, generated to maintain lump and fines product grades within acceptable tolerance ranges around targets. Achieving low variability requires predicting lump and fines grades as accurately as practical from the estimated head grades of the ROM ores potentially going into the blend. The grade prediction model may be either a direct prediction of crushed lump and fines grades and lump percentage, or be split into two stages: the bias between blasthole estimated head grade and crusher head grade and then the lump-fines algorithm for splitting the head grade between lump and fines products. The lump-fines algorithm comprises the percentage of lump and the difference between the lump and fines grades. We describe a weighted least squares (WLS) regression model for predicting crusher grades and lump proportion from the estimated head grade for Fe, P, SiO2, Al2O3, Mn and S. The method is applied to CNR production data, where the regression model explains approximately 60 per cent of the variance in the crushed ore grade, for both lump and fines. A further small but significant improvement in prediction can be achieved by including the ore classification data in the model. The regression errors exhibit strong positive serial correlation, indicating trends in grade error across multiple blend records. To compensate for the longer-term error, an exponentially smoothed model was developed and applied to the daily grade blend errors. This gave an increase in the longer-term variance explained and therefore an improvement in grade prediction.

Jan 1, 2009

By Frederick H. McDowell

Notwithstanding the rapidly increasing use of copper, due to the extension of its applications within the last few years, the fact of its continued steady decline in price stands prominently forward. Nor have we far to look for the cause. The opening up of the vast copper-deposits of our Western States and territories is the metallurgical event of the last five years. We must not forget, in looking at the new field, the changed conditions under which the metallurgist must work, as compared with the previous history of copper-smelting. Until quite recently, the copper-plants of the country were few in number; and the concentration of industry implied in this circumstance, allowed many practices which must be considered as inapplicable to the conditions offered at the many mines which have of late become such important factors in our copper-production. Thus the old style of smelting the ore for matte in brick furnaces, involving great expense and time in their construction, while deservedly losing repute even in its old strongholds, in comparison with water-jacketed smelters, is still in some cases adhered to. But to put up such furnaces at Western mines would be out of the question. The large and continual need of brick for relining and repairs acts as an effectual bar, when such furnaces come into competition with the light, portable, and easily managed water-jacketed smelters of improved types. It is owing to the present unusual activity, manifested in the opening up of new copper-properties and the erection of plants for working them, that any improvement in furnace-construction is of especial interest and importance. The method in which processes are copied without variation in the rapid growth of metallurgical interests, has already been strikingly exemplified in the history of

Jan 1, 1885

By Gerhard W. Heinrich, Gerald V. Schroeder, Daniel A. Murphy, Daniel F. Suarez, Jamie B. Beauchamp

"Washwater 'Finger' sprays were installed and tested in the copper/nickel separation circuit at Strathcona Mill to improve flotation capacities and related metallurgical performances. The new spray design features submerged sideways introduction of wash water into the flotation froth through nozzles at the end of vertical pipes which are suspended from a header above the froth. This maximizes the effective cross sectional area of flotation vessels while maintaining effective froth cleaning and a desirably high density of the concentrate slurry. The plant tests gave increases of copper concentrate production rates of 17% to 20% for conventional cells and 16% to 20% in column flotation at target grades of 29% to 30% copper and of less than 0.5% nickel. Basic considerations and concepts of tests and evaluation procedures are described.IntroductionMeeting flotation concentrate grade targets at maximum production rates and recoveries is a challenge all too familiar to operators of base metal ore concentrators. Frothwashing is an option to improve grade/recovery performance by minimizing entrainment of impurities into the concentrate, which is commonly known since the sixties (Kaya & Laplante, 1989). It has been recommended for the flotation of sulphides and industrial minerals alike (Kaya & Laplante, 1989; Miller, 1969; Heinrich, 1989) and has found its ultimate application in flotation columns (Finch & Dobby, 1990). The washwater addition in a flotation column is most evenly distributed over the column's cross-sectional area thus ensuring almost complete displacement of feed water from the froth by a countercurrent washwater flow -provided, a positive bias is maintained. Therefore, flotation columns are ideal for cleaning flotation. However, there is usually less room for boosting the concentrate production capacity by increasing airflow or slurry level then with conventional cells because of the smaller cross-sectional area available."

Jan 1, 1994

A variety of algorithms and methods are being used by the mining industry today to map mineral resource for reserve estimation. The traditional methods including Polygonal, Sectional and Inverse Distance methods are relatively easy to understand and implement. They have served industry well for several decades and should continue to do so for the large bulk mineable deposits with very regular geometries with relatively small variation in grade.

Jan 1, 1992

By A. A. Millar

THE output of coal from the Province of Alberta reached its peak; in the year 1928, when 7,334,179 tons were produced. Following this, a steady decline was recorded, and in 1930 a low mark of 4,564, 290 tons was made. Since that time, however, the tendency has been upward, and this year (1937) 5,551,682 tons were produced, compared with 5,696, 375 tons in 1936 and 5,462,973 tons in 1935. The value of the output in 1937 was $14,434,969, against $14, 720,004 in 1936. The coals of Alberta have been classed under three heads, viz., domestic, sub-bituminous, and bituminous The domestic (or lignite) and the sub-bituminous coals are used chiefly for domestic purposes, with the possible exception of the smaller sizes and the output of the two stripping pits at Stereo and Coal Valley The bituminous output is used mainly by the railways, for locomotive purposes, which, in 1937, accounted for 80.6 per? cenr of the total sales of bituminous coal. A fair proportion is sold for stationary engine and steam purposes and, in 1937, 25,000 tons were used in making briquettes at plants operated by the Canmore Coal Company, Limited, and Brazeau Collieries, Limited. The International Coal & Coke Company, Limited, used 99,500 tons in their plant at Coleman, for making coke. The bulk of the 66,000 tons of coke produced was sold for use at the smelter at Trail, B.C.

Jan 1, 1938

By E. Pardo-Igúzquiza, R. A. Olea

The bootstrap is a computer-intensive resampling method for estimating the uncertainty of complex statistical models. We expand on an application of the bootstrap for inferring semivariogram parameters and their uncertainty. The model fitted to the median of the bootstrap distribution of the experimental semivariogram is proposed as an estimator of the semivariogram. The proposed application is not restricted to normal data and the estimator is resistant to outliers. Improvements are more significant for data-sets with less than 100 observations, which are those for which semivariogram model inference is the most difficult. The application is illustrated by using it to characterize a synthetic random field for which the true semivariogram type and parameters are known.

Jan 1, 2015

By M Rauer

With a worldwide growing population the demand for higher living standards, food and the development of new technology is rapidly rising. To allow for a continuous growth, larger quantities of minerals and raw materials are needed at a faster pace. Different methods have been developed to access or tap ore more quickly, such as improved drill and blast operations, mechanical mining methods using equipment such as roadheaders (RH), longwall miners and other technical equipment. Another possibility to access and develop mines faster is the use of a tunnel boring machine (TBM).The historical usage of TBMs is surprisingly long, but the opportunity for technology adoption by the majority of worldwide mining companies remains largely untapped. Dozens of full face TBMs have been used by mines around the world, including two that will begin operation soon in Australia. TBMs have been used to safely and rapidly gain access to the orebody, or to expand access to the orebody to increase output by running a TBM along the edge of the orebody for several kilometres. These machines have also been used for ventilation and for conveyor tunnels for ore removal. They have been used to quickly excavate long and winding declines giving access to an orebody at several levels in a short period of time.Tunnel boring technology can be used for mine declines, mine access tunnels and all sorts of different mine designs and set-ups. TBM technology simply needs to be adapted to the mine conditions and, if manufacturers are involved early on in the planning process for mine development, the operation can be very successful. In some cases, historically typical mine designs may need to be re-thought.One mine, the Stillwater Platinum mine in Nye, Montana, is currently employing its fourth TBM in 25 years. Two were used to create tunnels running alongside the orebody, rapidly expanding access to the orebody in many locations for increased output. Two were used to create parallel access tunnels to a mine expansion at the East Boulder orebody; one tunnel is for conveyor haulage and the other for vehicular access. TBMs have been employed successfully many times to rapidly drive vehicular decline tunnels to multiple mine levels, such as at the San Manuel – Magma Copper mine in the USA. While TBM technology may not seem to be optimal for every mine, these success stories show that the method can provide vast benefits for the right projects.Early use of TBMs in extremely hard rock metal mines, in the 1960s and 1970s, had limited success since performance was low. However there have been great improvements made over the years in the strength of rock which can be excavated by TBMs with high performance. Other important improvements involve the provision of a safe work environment, safely and rapidly supporting the rock and predicting geology ahead of the TBM.This paper will briefly note the more than 20 TBM mining projects and highlight some notable successes. It will then go on to give a status report on the two active TBM mining projects in Australia and the difference between a TBM operation versus other excavation methods such as drill and blast (D&B) or RH excavation.CITATION:Rauer, M, 2014. Tunnel boring machines in mines – a?brief review of past use with a status report on use today in Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 663–670 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By A. Gillis, J. Keyes

"This is a prelirr1inary report on automatic control at East Malartic Gold Mines.After installation of the cyclones in the East Malartic grinding circuit, the interest was aroused in the automatic control system for the circuit. Investigations were made as to the possibilities of such an installation. This resulted in a preliminary survey of the circuit by Milltronics Ltd and an analysis of the circuit by Mines Branch personnel. A study of the investigation and analysis indicated that a cost reduction and improved efficiency could be expected by the installation of an automatic control system in the grinding circuit. It was also indicated tl1at such installation should pay for itself within a year. This was the point that sold management on such installation. The need of three operators was expected to be eliminated .The installation was to consist of a central control panel, microphoncs on each mill, regulation of feed rate, pneumatic valves for addition of solt1tions, density control of the cyclone overflow, which is a grinding circuit product, rod mill feed box plugging detector and a conveyer weightometer for tonnage indication and control.As well as the elimination of one man per sl1ift, other benefits which were to be received but unable to estimate were: 1) More tonnage per clay by operation of the mills at the proper capacities. 2) Lower grinding costs. Less under-loading should result in less steel wear and lower pumping cost. In the condition of overloading, a coarser grind is obtained resulting in greater impeller and liner wear. The overloading and underloading showed up on the n1icropl1oncs. 3) An improvement in the recovery as a result of less over-load. The tailings loss from a coarser grind are not as frequent."

Jan 1, 1965

By Fernando Concha

"Thickening development and innovation in the 20th Century occurred in two decades periods. From 1900 to 1920, Dorr invented the continuous thickener and the first method of thickener design was proposed by Coe & Clevenger. From 1920 to 1940, the operating variables of continuous thickening were discovered by Comings at the University of Illinois. From 1940 to 1960, the first theory of sedimentation was proposed by Kynch and several authors, Talmage and Fitch, Ysioka and Hasset used this theory to develop new thickener design methods. From 1960 to 1980 Shannon and Tory demonstrated that this theory applied exactly for the sedimentation for small rigid spheres in water and Scott showed that it is not valid for flocculated suspensions. From 1970 to 1990 the phenomenological theory of thickening was developed based on the theory of mixtures. Papers by Kos, Bascur, Thacker and Lavelle, Concha and Bascur, Concha and Barrientos, Auzeris, Buscal and White, Landman, White and Buscal show the application of this theory to thickening and Adorjan presented the first thickener design method based on this theory. In 1980s the mathematical analysis and solutions of Kynch’s model for batch and continuous thickeners was obtained by Bustos. The new Century brought solution to the phenomenological thickening model which was applied to thickener design, simulation and control. The method of thickener parameter determination was improved by designing new laboratory and on-line instruments and advanced control strategies was designed and validated in plants. Structural thickener design produced improved feedwells and feed dilution mechanism, stronger raking mechanism and different thickener shapes according to new ambient requirements, such as high rate thickener and paste thickeners that increase the water recovery. New challenges include better flocculation and advanced control strategies."

Jan 1, 2014

By J. A. Musselman, J. B. Cheatham

In recent years considerable effort has been expended in the search for new ways of drilling into the earth's crust and for improvements of existing methods. A number of novel techniques have been explored such as explosive, flame, electric arc, abrasive jet, chemical, and various percussion-type dri1ls.l Some of the new methods are useful in isolated situations, but rotary drilling continues to be the most versatile and generally economical method for rock drilling. An understanding of rock failure during drilling can lead to improved rotary drilling techniques and to the development of new methods. Experiments 2-4 have shown that rock strength and ductility increase with increasing pressure; therefore, meaningful experimental investigations should be carried out under conditions similar to those encountered at the depths to which oil wells are drilled. The action of a roller-cone bit is not pure rolling in all cases but frequently involves gouging and scraping action. However, vertical penetration of a horizontal rock surface by a single punch has served as a first approximation of the rock/bit tooth interaction during drilling.5,6 In these experiments semi-infinite smooth rock surfaces are indented by steel tools with configurations having various degrees of dullness. Both static and dynamic tests have been investigated; however, static loading provides a good approximation of the loading rates occurring during rotary drilling. As a more realistic approximation to actual drilling conditions, chip generation must also be considered. Recently, studies have been made of indexing or chipping from a bit tooth to a previously formed crater.7-9 The purpose of the present investigation is to study indexed penetrations in greater detail. Fig. 1-A illustrates the general problem. Pittman and Cheatham 10,11 have used plastic limit analysis to study the idealized plane-strain indexing problem for a material having a linear Coulomb-

Jan 1, 1972

By Heyes GW, Orrock GI

The fine grained complex orebody at Elura contains galena, silver and sphalerite in a matrix which is mostly pyrite; sulphides account for about 90% of the orebody. A differential flotation circuit is operated to con- centrate lead and silver in the first section and zinc in the second. The metallurgical performance to date indicates the need for improvement. The lead section has been sampled in detail to comprehensively assess its overall performance and to define problems associated with lead and silver flotation. The substantial amount of pyrite in the feed dominated the perfor- mance of each stage of the separation. It was responsible for extensive dilution of all concentrates and, as a consequence, for very large circulating loads. The rougher concentrate contained 68% pyrite some of which was rejected through the three stages of cleaning to 39% in the final concen- trate. However, this was still sufficient to hold the assay of this product below 45% Pb. Size by size behaviour shows that flotation rates of the valuable minerals, as characterised by their rate coefficients, were low through- out the circuit. There was a significant deterioration in these rates between rougher and cleaner I stages which resulted in large circulating loads between these stages. There was practically no recovery of coarse valu- able minerals to the final concentrate. The dilution of the final concen- trate by non-sulphide gangue was not a major problem. If the recovery of the galena and silver in the +38¦m size range could be raised to that of the - 381Lm size range, galena recovery would rise from 78% to 86% and silver recovery would improve from 46% to 59%. The Pb grade of the final concentrate would remain the same.

Jan 1, 1988