Search Documents

By R. Letsaole, H. Mabowa, J. Sehat, J. Tshilongo, T. Rampfumedzi, N. Ntsasa, A. Mkhohlakal1

This study explores the use of co-collectors to enhance the recovery and determination of rhodium during fire assay with lead collection, followed by acid dissolution using conventional hot plate methods. Rhodium, a critical platinum group metal, poses analytical challenges due to its low natural abundance and complex chemistry. Among the co-collectors tested, palladium and tellurium demonstrated significantly improved rhodium recoveries, ranging between 100% and 120%, whereas silver resulted in poor recovery and higher error margins. These findings highlight that co-collectors can enhance the efficiency and sensitivity of platinum group metal analysis, although their effectiveness is dependent on the chemical interaction with the target element. Acid dissolution was essential to ensure complete digestion of prills prior to analysis, enabling accurate quantification of rhodium. Overall, the findings suggest that palladium and tellurium are effective co-collectors for rhodium determination in fire assay, while silver and lead flux alone are unsuitable. This work provides important insight into optimising fire assay procedures for reliable rhodium analysis, with potential benefits for platinum group metals recovery and economic evaluation.

Mar 6, 2026

By Bernard Y. Saltie

The White Pine orebody is characterized by a high lateral stress or highly faulted and joined conditions. Because of these difficult conditions roof support has always been a main concern. Mechanical bolts were widely used in the early seventies; however, it became apparent that major improvements in ground control were required if safe operation at White Pine was to be continued. The first step was taken in 1973-1974 with the testing of resin bolting. Record of caves and roof-falls with either type of support demonstrated superiority of resin bolting versus mechanical bolting - Safety was dramatically improved which was the absolute first consideration; however resin bolting was still more expensive than mechanical bolting. In order to generalize resin bolt installation, the second step was therefore to acquire special roof bolters compatible with resin bolting. The machine was to enhance the safety of the operation. This was achieved by the acquisition of the Secoma bolting machine equipped with an automatic bolting turret. Being a "hands off" operation the safety of the operator is total. Using a fixed taped attachment of the drill steel on the chuck a front guide and an automatic regulator torque thrust on the steel drilling in small diameter was possible. Being a fully automatic process only one operator is required per machine versus two operators with the conventional machines. The two main objectives were reached enabling the extension of resin bolting to the whole mine.

Jan 1, 1980

By C. A. Cole

This work consists of research in cable fault location and the construction of four field-test units based on the research. Swept-frequency sounding of mine cables with RF signals has been the technique most thoroughly investigated. The swept-frequency technique is supplemented with a form of moving target indication (MTI) to provide a method for locating the position of a technician along a cable and relative to a suspected fault. Separate, more limited investigations involved high-voltage time domain reflectometry and acoustical probing of mine cables. Particular areas of research included microprocessor-based control of the swept-frequency system, a microprocessor-based fast Fourier trans-form for spectral analysis, RF synthesizers, transmit-receive switches, RF receivers, cable dispersion-compensation techniques, low-voltage multielement display systems, and techniques for injecting or recovering RF energy through cable walls in support of clamp-on fault locators.

Jan 1, 1982

By Yuexin Han, Zehong Wang, Fujia Yu, Wanzhong Yin, Xinchao Wei

Bauxite is the main raw material in alumina and refractory industries. China has plentiful bauxite resources, most of which belong to the diaspore type bauxite with characteristics of high aluminum content, high silicon content and low ratio of alumina and silica (A/S). The resources with A/S 4-7 account for more than 60% of the total resource reserves of bauxite. Therefore improving the A/S through bauxite desilication is the key task of bauxite concentration in China. Normally the grinding fineness of 80-90% - 0.074mm is required in the bauxite flotation process. Thus fine grinding of bauxite ores is necessary, which leads to the high energy consumption. In the meanwhile, bauxite ores are easy to produce slime during grinding processes. The large amount of slime produced in fine grinding greatly worsens the process environment of bauxite flotation, affects the separation performance and results in the loss of metal. Also, fine grinding makes the flotation concentrate difficult to dewater, while the water content in the flotation concentrate must be removed by distillation in the subsequent alumina dissolution process, causing the increase of energy consumption and cost in the production of alumina. In this study, the selective grinding behaviors were examined with Henan Bauxite as feed. Separation of alumina and silica at a coarser grinding fineness was achieved and new route was explored to enhance the desilication in bauxite concentration to improve the A/S of bauxite concentrate.

Jan 1, 2003

By H. Hejny

Given the current status of political discussion in Europe about raw materials issues, the sustainable development of the extractive industry and the reduction of its environmental and societal footprint are among the key topics in this discussion. In this context, the European Commission approved the EO-MINERS project (Earth Observation for Monitoring and Observing Environmental and Societal Impacts of Mineral Resources Exploration and Exploitation). The overall aim of EO-MINERS is to bring into play EO-based methods and tools to facilitate and improve interaction between the mineral extractive industry, authorities, and the society in view of its sustainable development while improving its societal acceptability. Developing generic, standardised and reliable EO-based products to monitor the environmental and societal footprint of mining projects is the way chosen by EO-MINERS to improve this interaction, along with the organisation of tripartite meetings gathering all relevant stakeholders. The project uses existing EO knowledge and carries out new developments on three demonstration sites (Sokolov lignite mining area, Czech Republic, Witbank coal field, South Africa, Makmal gold mine, Kyrgyzstan) to further evaluate and demonstrate the capabilities of integrated EObased methods and tools in monitoring the environmental and societal footprints of the extractive industry during all phases of a mining project, from the exploration to the exploitation and closure stages. It contributes providing reliable and objective information about affected ecosystems, populations and societies, to serve as a basis for a sound ?trialogue? between corporate stakeholders, governmental organisations and societal stakeholders. The project already developed a set of consolidated indicators based upon previous knowledge about mining-related issues along with interviews of national, regional, and local stakeholders. These indicators reflect known environmental and societal issues at mining sites as well as the interest of various relevant stakeholder groups. The process described in the EO-MINERS project ? policy assessment > indicator identification > choice of suitable EO tools able to serve monitoring task > monitoring by EO tools > making available objective information for fair dialogue among stakeholders ? is generally applicable to all stages of a mining project. The key to success will be the right choice of indicators addressing the problem and subsequently the right choice of suitable EO tools and finally the willingness of all stakeholders to find a common solution. To this end, the EO-MINERS project organises site-specific ?trialogue? workshops at each demonstrations site, which aim to provide relevant information in adequate quality to the stakeholders as common ground for discussions. Local stakeholders, including mining companies, regulatory bodies, and community representatives are invited to participate in these workshops where the relevance of the developed EO-based products to environmental and societal impact assessment will be discussed. The presentation will discuss results obtained during these trialogue workshops, as well as the success and difficulties and reluctances encountered. The project will further indicate ways and means how the EO products and other project results may be used for monitoring purposes in all phases of a mine.

Aug 1, 2013

The U.S. economy and, consequently, the demand for minerals grew at more moderate rates in 1995 compared with stronger performances the previous year. Demand for metals such as steel and copper was relatively stable. For example, the decline in steel consumed in motor vehicle manufacturing (reflecting lower vehicle sales) for the first half of 1995 was offset by an increase in steel consumed in construction during the same period. More detailed information on events, trends, and issues in the mineral and material sector Is presented below and in the commodity sections that follow. Overall Performance The value of processed materials of mineral origin produced in the United States during 1995 was estimated to be $395 billion, an increase of almost 10% compared with 1994. The estimated value of U.S. raw nonfuel minerals production in 1995 was $38 billion, about 7% more than in 1994. The value of U.S. minerals production has increased in 30 of the last 35 years.

Jan 1, 1996

By C. Frenzel, N. Blechschmidt

"INTRODUCTION There is no doubt about the time and effort companies put in establishing and maintaining their equipment. However, the question about how these companies can map the benefits comes up. Neither do they have the tools to quantify the benefit of their action, nor do they have the tools to know the actual quality of their current maintenance system. The resources used in the process seem futile to observers. It seems impossible to trace improvements and to get information about the impact of actions in retrospect. Improvements in maintenance performance cannot be recognised by management or shareholders. Thus the necessity for measuring the performance of maintenance systems is given. In this paper ConMoto is systematically showing the strengths and weaknesses of many companies' maintenance management and is providing field-tested proven design elements for measuring maintenance systems and implementing Value Oriented Maintenance. Considering only business assets in production facilities and related machinery out of all investment goods in Europe, you reach a value of around 9.7 trillion euros in 2008. In Germany alone the equipment replacement value amounted to about 1.9 trillion euros [8,10,11,13]. If you calculate a cross sector maintenance costs rate of 4.8 % (corresponding to the average value identified in this study), direct maintenance costs in European production locations add up to over 450 billion euros per year [3]. These figures speak for themselves. Yet maintenance is not only of enormous significance for European enterprises. Our experiences show that maintenance and asset management, particularly sustainability issues, are also increasingly moving to the forefront in the BRIC states, in the Middle East and in many emerging countries. First of all, in order to meet the resulting high quality and cost related requirements of maintenance systems, a comprehensive overview of the issue is needed. This overview is provided by a detailed analysis of 83 companies and production plants from various sectors – with amazing results. SIGNIFICANCE OF MAINTENANCE Current studies show the high financial significance of maintenance and asset management. According to the market study in the Asset Manager [9], in industrialised countries about 10 to 15 per cent of the labour force are employed in maintenance and facility management tasks. In Europe about 40 to50 million people are directly and indirectly involved in retaining the value of machinery, plants, buildings, transport systems and infrastructure facilities. A glance at the costs side also demonstrates the great relevance of maintenance. EU-wide annual direct maintenance costs amount to a total of more than 1,500 billion euros. In Germany alone they are about 250 billion euros. This impressive total is considerably exceeded by indirect maintenance costs caused by technical failures. Indirect costs are estimated to be five times higher (Figure 1). [7,12,14]"

Jan 1, 2018

By Narasimha Mangadoddy, Teja Reddy Vakamalla

"Vertical hydrocyclones are very common in most of the comminution circuits. Inclined cyclones are also found for specific mineral processing applications. In this work, Computational Fluid Dynamics (CFD) technique and experiments are used to find the reasons behind the inclinations effect on hydrocyclone performance characteristics. The water and silica slurry experiments are conducted with 75 mm hydrocyclone at different inclined positions (0-600) to the vertical plane. Corresponding two-phase numerical simulations are performed with Volume of Fluid (VOF) model coupled with Large Eddy Simulation (LES) turbulence model. Multiphase simulations are carried out with Algebraic Slip Mixture model modified with lift, drag forces and Newtonian rheology model corrected with fines for various feed solids concentration. A raise in the under flow solids percentage, cut diameter and a reduction in the water split is observed with the inclination. Electrical Resistance Tomography (ERT) and High Speed Video (HSV) data is used to cross validate the inclined cyclone’s CFD air-core and solids concentration data. Predicted efficiency curves are found in a close agreement with experiments for all the inclinations. Comparison of experimental and predicted flow data clearly follows trend with the literature. Key words: Hydrocyclone, CFD, ERT, inclination, water splitINTRODUCTIONHydrocyclones are devices used to separate or classify particles based on particle size difference in the water medium. Their usage is very wide in chemical, petroleum, mineral and bio industries due to its structural simplicity, high throughput, small volume, low cost and maintenance. Cyclone mainly consists of a cylindrical section followed by a conical section attached to a single feed inlet and two product outlets named vortex finder and spigot. It works on the principle of centrifugal sedimentation. The slurry is fed tangentially to the hydrocyclone, in which larger particles are moved towards the wall and separated by centrifugal forces to the underflow. Smaller size particles follow liquid due to drag forces to the overflow. With its simple structure, the flow behavior inside the hydrocyclone is quite complex. Vertical cyclones are common in practice in most of the comminution circuits. Horizontal cyclones can be found in extreme cases which are for installation convenience rather than for process reasons. Inclined cyclones are also present for specific mineral processing applications. In coal preparation plants, dense medium cyclones are operated near to horizontal inclination of 20 degrees to allow large spigot sizes for sinks removal, self-drain of contents during shutdown. In the phosphate removal, dense medium cyclones are inclined with an angle between 0-90 degrees for better separation of ore and tailings (Liu Feng et al., 2006). Even in the clusters, hydrocyclones are mounted with an inclination around the feed distributor for uniform distribution of slurry and under flow collection. It is believed in mineral processing industry that inclined cyclones would fetch the benefit in number of ways while classifying the material by size. Gravity influences the cyclone performance through the air core size and position variations in large cyclones. It also favours the cyclone operation at coarser cut points without varying any other design and operating parameters. Minimizing fines misplacement to underflow can be achieved with inclination."

Jan 1, 2016

By Y. Maeda

Kosaka Smelter is a copper smelter located at the nothern part of Japan? and has been treating. complex sulfide concentrates using flash smelting technology for a long time. The flash smelting technology has an advantage in the point of controllability of matte grade and heat balance in the reaction shaft. But the disadvantage of this process, is that the dust generation ratio is high compared with other smelting process such as injection smelting technology. This reason why is that the flash smelting process is the oxidation process for the fine sulfide concentrates applying flash reaction in the oxygen enriched stream In addition of this disadvantage, the sulfide concentrates contains much volatile impurities is resulted the dust; eneration ratio more. This paper outlines the recent improvement of the flash reaction in the furnace and the behavior of impurities in Kosaka Smelter.

Jan 1, 1998

By Y Potvin

Risk assessment in the mining industry is currently a topic of great interest with risk methodologies being increasingly applied beyond the traditional areas of finance and feasibility to analyses of risks due to various physical hazards including chemical, electrical, mechanical and geotechnical sources. The application of risk analysis and evaluation techniques to the management of personnel safety is being promoted by both industry and regulators but, particularly for geotechnical hazards, often there are inadequate databases for a meaningful quantitative calculation of risk. In Western Australia over the decade 1987 - 1997, the annual fatality rate for underground mining has averaged at approximately 1.3 in 1000 employees with rockfalls/rockbursts accounting for over half of these deaths (Prevention of Mining Fatalities Taskforce, 1997). Recent improvements have been made since this time, perhaps halving the annual fatality rate, mainly due to industry improving ground control measures and implementing various recommendations from the Prevention of Mining Fatalities Taskforce (1997). However there still remain a large number of unknowns when trying to address the complex area of geotechnical risk in mining. Risk calculations require information about the source of the hazard, the people or assets exposed to the hazard (the æelements at riskÆ) and the effects on these vulnerable elements if the hazard actually occurs (the potential consequences). To date, little information has been available on the exposure of mining personnel and equipment to underground hazards other than occupational safety studies on chemicals, heat, dust, etc. This paper concentrates on underground geotechnical risks and presents a data collection and rating system for the exposure of both the underground workforce and equipment to rockfalls and rockbursts. The methodology considers exposure times, personnel protection levels and hazard proximities to give exposure ratings for the major underground mining activities and hence rate different locations within a mine. This exposure methodology is then applied to the workforce and production/ development cycles in an actual WA underground mine, creating a snapshot map of differing levels of personnel exposure across the mine.

Jan 1, 2003

By Percival Roberts

It may seem necessary to offer an apology for presenting for consideration a process which is conspicuous by its absence in the literature of the Institute, and which may be thought by some to belong to the past in metallurgy, and to have been already superseded. But the large capital invested in puddling calls for a careful consideration of the question whether the time has certainly arrived when the puddling furnace must be replaced by the converter and open-hearth furnace. May there not still be a place for puddled iron alongside of molten iron and steel, and is not the improvement of the puddling process itself worthy the attention of engineers equally with the Bessemer and open-hearth processes? The changes involved in the conversion of pig iron into wrought iron are well understood and need only be briefly alluded to. The patent of Henry Cort bears the date of 1784. Since that time * the improvements in the process have mainly consisted in the replacement of sand by iron bottoms by Samuel Baldwyn Rogers in 1818, and the still more recent substitution of iron oxide for the refractory materials used for the rides and bridge of the hearth, which distinguishes the wet or boiling process from the dry or pnddling process. Chemically, the process consists in the removal of the metalloids from the pig iron, a result effected mainly by the iron oxide. Silicon is first oxidized, then the phosphorus, and finally the carbon. The silicic and phosphoric acids produced pass into the cinder and the carbonic oxide burns as it escapes from the bath of metal. It is interesting in this connection to note the effect of temperature on the removal of the phosphorus from the iron. As is well known, no phosphorus is eliminated under the oxidizing influences prevailing in the Bessemer converter, while from 70 to 80 per cent. is removed in puddling. But we find, if in working cold short irons

Jan 1, 1880

By Percival Roberts

IT may seem necessary to offer an apology for presenting for consideration a process which is conspicuous by its absence in the literature of the Institute, and which may be thought by some to belong to the past in metallurgy, and to have been already superseded. But the large capital invested in puddling calls for a careful consideration of the question whether the time has certainly arrived when the puddling furnace must be replaced by the converter and open-hearth furnace. May there not still be a place for puddled iron alongside of molten iron and steel, and is not the improvement of the puddling process itself worthy the attention of engineers equally with the Bessemer and open-hearth processes? The changes involved in the conversion of pig iron into wrought iron are well understood and need only be briefly alluded to. The patent of Henry Cort bears the date of 1784. Since that time the improvements in the process have mainly consisted in the replacement of sand by iron bottoms by Samuel Baldwyn Rogers in 1818, and the still more recent substitution of iron oxide for the refractory materials used for the rides and bridge of the hearth, which distinguishes the wet or boiling process from the dry or paddling process. Chemically, the process consists in the removal of the metalloids from the pig iron, a result effected mainly by the iron oxide. Silicon is first oxidized, then the phosphorus, and finally the carbon. The silicic and phosphoric acids produced pass into the cinder and the carbonic oxide burns as it escapes from the bath of metal. It is interesting in this connection to note the effect of temperature on the removal of the phosphorus from the iron. As is well known, no phosphorus is eliminated under the oxidizing influences prevailing in the Bessemer converter, while from 70 to 80 per cent. is removed in puddling. But we find, if in working cold short irons

Jan 1, 1880

By Rudolf Gahl

Some time ago the Detroit Copper Mining Co. had to decide the question whether it would pay to re-treat slime-tailings, and several machines were tested in order to ascertain the type of construction which would give the greatest saving. In previous tests on the ore of this company, several tables proved far inferior to the Frue vanner, and for this reason they did not receive any serious consideration. In the late tests, however, one table was found to surpass the vanner in the percentage of saving made. The Frue vanner used in these tests had been adjusted approximately to the slope which the slime-vanners in the concentrator of the Detroit Copper Co. had at that time, about 2 in. between the inside of the wooden posts, or 0.272 in. per ft. It had not been determined, however, if this slope was the most economical one for treating the slime-feed in the mill, or for re-treating the tailings from the slime-vanners, and I was instructed to ascertain by test-runs, under different conditions, the best adjustments for the work to be done. In order to determine if a change in the adjustments of the machines would improve the results, it seemed sufficient to continue running the tests between the vanner and the table before mentioned, keeping the feed and all other conditions the same, but varying the adjustments of the vanner from run to run. I employed a vanner-man of long experience to operate these machines, who expressed the opinion that a slope between 28 and 2.5 in. between the posts (0.323 and 0.340 in. per ft.) would give the best results. Some runs made this way gave a considerable improvement. While for a slope of 2 in. (0.272 in. per ft.) the saving had been only 40.5 per cent. of that of the table, it was 49.2 per cent. for 2.5 in. (0.340 in. per ft.) slope. A decrease of

Jan 1, 1910

"Acid resistant brick lined autoclaves and related vessels are utilized in pressure oxidation for the recovery of gold, copper, and other metals. The combination of the corrosion resistant membrane, acid resistant brick, mortar and steel shell is a composite system that requires a sophisticated stress analysis. In order to obtain meaningful results both the model and physical properties of the materials must be carefully selected. Evaluation of the calculated results requires an understanding of both the failure mechanisms of ceramics and experience with the performance of existing lining systems.INTRODUCTIONAcid brick lining systems are used in pressure oxidation autoclaves and related vessels to provide thermal and mechanical protection for corrosion resistant membranes that are applied directly to the interior of the vessel shell. The acid brick and mortar must be resistant to the process conditions and must provide a mechanically reliable structure.The construction of lined vessels incorporates a wide range of materials that can include the carbon steel vessel, austenitic weld overlay, lead lining, organic membrane, ceramic brick, mortars and other alloy components. The physical properties of the materials can vary by orders of magnitude and when combined in the construction of the lined vessel create a complex composite structure. The materials may be bonded together or act independently of each other. Stresses are induced into the lined vessel include pressure, thermal expansion, chemical expansion and mechanical loads.The complexity of these systems makes it is very difficult to account for all of the variables in the structural analysis of lined vessels. Historically calculations were simplified and designers primarily relied on experience with previous applications.The greatly improved tools for Finite Element Analysis (FEA) available today allow for detailed calculation of the stresses imposed on the vessel shell and lining. Koning & Lauzon (2004) presented a paper on design fundamentals including a discussion on the application of FEA methods at Pressure Hydrometallurgy 2004 in Banff. When a designer carefully constructs a model and selects the correct materials properties for the calculations, meaningful and useful results can be achieved."

Jan 1, 2012

By W. H. Adams

One of the most attractive subjects for technical writers is the gigantic industry of the manufacture of sulphuric acid. This is no doubt, natural when we take into account that it has grown in this country during the past twenty years, from a production of 60,000 tons in the year 1867, to that of nearly 450,000 tons in 1887. We may well excuse much of the literature which but repeats the same old story, as it serves to bring to the public notice, at proper intervals, the hidden resources of our land; and this constant application of essential truths will sooner or later be the means of freeing us from dependence upon the Old World for necessary chemical products. The present increase in manufacture of this acid in the United States is almost wholly from pyrites ores, which we have in unlimited quantities close at hand. The largest consumption of such acid is for treatment of other native products, petroleum, rock-phosphates, etc.; and, considering the knowledge we have gained during the past twenty years, it is safe to say that the industry is but fairly established, and the causes which have operated to place us in our present proud position are but natural incentives for a further growth and an increased consumption of the many other undiscovered or undeveloped resources of our American soi1. In one of his earlier editions Muspratt says: " It would seem that the manufacture of sulphuric acid, though as extensively carried on as any other business, yet seems to be the least understood; and the ignorance of some manufacturers appears to be only equalled by that of writers, who, in their description of the production of this acid, give figures of apparatus, and vaunt as improvements, things which have been exploded for years. It is possible to find in the works of eminent men drawings of apparatus, for the production of sulphuric acid, which never could possibly have worked one day—some, in fact, could never have worked at all."

Jan 1, 1888

By B Dold

Western Europe is a dynamic region, with an emerging co-operation between the individual nations both politically, economically, technically and scientifically. The European Union, today with 15 member States and with a range of central European States applying for membership, is a catalyst for this Cupertino, using a combination of EU funds, for financing research initiatives, and legislation to enhance development of technology and environmental performance. Europe is a major net importer of metals but with a large potential for own production, in particular in the accession countries. The metals and mining sector is furthermore identified as having a large potential to generate wealth both in todayÆs EU and in the future, widened Union. This paper provides a chart of examples on the many research initiatives presently underway in Europe, addressing environmental issues related to mining. The list of programmes and projects does not claim to be complete; it is rather an illustration on the wideness of the approach, describing various ways for transboundary Cupertino. The approach taken by many of the programmes goes beyond the strict ARD scientific area and therefore only a limited number of the many programmes can be identified as ARD research programmes. Also national programmes, without EU funding, are operating, eg in Sweden, Germany, and UK. The picture is continuously changing with new programmes being commissioned and old ones being completed.

Jan 1, 2003

By A. B. Hooker

Since man first mined underground, there has been need for adequate illumination; this need has never been fully supplied. At first, suitable lamps were not available. Gradually they have been developed, but along with that development the need for better and better lamps has continued owing to the following conditions and factors: 1. Increasing hazards from gas and dust ignitions. 2. The speeding of operations with mechanized mining, which necessitates greater visibility. 3. A demand that cleaner coal be loaded, which requires higher levels of illumination. 4. The cost of compensation for injuries that has created a demand for better illumination and safer lamps. Use of better lamps has been retarded by: 1. Prejudice and resistance to change on the part of the workers in some districts. 2. The cost and upkeep of the lamps. 3. The present types of lamps, while a great improvement over the old lamps, do not entirely fulfill the requirements for a safe and efficient light for underground workers.

Jan 1, 1938

By M J. Newton

As part of the AMIRA P843 project Keeney and Walters (2008) describe how the principal components analysis (PCA) method can be used to identify classes of samples with similar metallurgical characteristics. However PCA does not take account of the location of each sample in 3D space. This paper describes a study to analyse the spatial distributions of the classes and determine appropriate modelling methods to control the estimation of the comminution parameters and mill performance indices into a 3D block model. This includes but is not restricted to geostatistical techniques that are used for grade modelling. The starting point for the study is the class definitions and the regression models for estimating the comminution parameters and performance indices. Each sample is assigned a class and the spatial distribution of each class has been analysed using different techniques including the calculation of variograms. This establishes whether the classes can be used as domain control for estimation into the block model – a procedure similar to using geological rock type domains for controlling the estimation of grades for a resource model. However, standard geostatistical estimation methods such as ordinary kriging assume that the variable being estimated is additive or linear. This assumption is valid for variables such as grade but this is not necessarily the case for the comminution parameters or the performance indices. Therefore the estimation procedure must either use variables that are definitely additive or the effect of potential non-additivity must be tested and accounted for where possible.The results of the study show how performance indices such as recovery, throughput and specific power can be estimated into the block model. This model is then combined with the geological model to provide a multi-parametric model that is used to optimise the mine planning and scheduling activities which can lead to significant improvements in NPV.

Sep 5, 2011

By B. Genc

Safety in South African mines is a subject of significant interest, since many mining companies are experiencing production deficits due to safety-related stoppages. In this paper, safety data from the South African platinum mining sector is analysed for the period 2006 to 2010. The data was obtained from company annual reports as well as the Department of Mineral Resources, and analysis in the study is limited to injury and fatality data only. The overall safety performances of companies in the sector are compared, and opportunities for benchmarking and recognising potential sources of best practice amongst platinum miners are identified. Improving safety usually incurs a cost, and mining companies are particularly conscious of the importance of controlling costs. However, cost considerations often deal only with direct costs, and it has been shown that indirect costs are usually far more significant. Therefore, a greater safety spend will usually result in the creation of value for the mine since it will reduce the indirect costs associated with accidents. The results of some recent research in this area are presented. In this light, where available, the financial performances of mining companies in the sector, obtained from published annual results, are included in the benchmarking exercise to determine whether there is any correlation with safety performance.

Jan 1, 2012

By M. Mpofu, B. Maphalala, S. Khan, S. Ngobese, D. Roberts

This paper details an assessment of stemming practices at a South African opencast coal mine and their influence on ground vibration and air blast. Quantitative and qualitative analysis methods were used for the study. The parameters assessed for the quantitative analyses included stemming length, stemming material type, blast-hole depth, burden, and spacing. Pre-blast data from the mine was analysed to determine the deviation between actual and mine design stemming parameters. Mine design stemming length was also compared to the rule-of-thumb stemming lengths. Peak particle velocity (ground vibration) and air blast data from seismograph stations around the mine was analysed to determine the correlation between stemming length and excessive ground vibration and air blast. The qualitative analysis involved observations of blasting procedures at the mine to determine compliance with mine procedures. Some level of non-compliance of actual stemming parameters to design stemming parameters was found, which initially suggested that non-compliance may have contributed to excessive air blast. However, further analysis of the seismograph results indicated no direct correlation between stemming length and excessive air blast and ground vibration. Since stemming parameters are interrelated, it is crucial that all blasting procedures, including stemming, are executed in accordance with best practice, and recorded accurately. There is a need for digital systems for capturing on-bench blasting parameters, as the currently used manual data recording and reporting systems are inefficient and prone to error. Improvements to blast designs are possible through efficient and accurate data recording and reporting systems.

Jan 1, 2021