Search Documents

By Eric L. Trist

The objective of this contract was to review the results of the Rushton Mining experiment in work organization and design, to explore the extension of knowledge gained from Rushton to other underground coal mines, and to conduct a search for a potential mine site for a demonstration project. The primary focus of the contract was on a search process to provide the research team with the opportunity to evaluate the different potential experimental sites, in order to select one or more with the highest potential for success. This search process also provides the various levels of union and company officials the opportunity to fully understand the context of the research before making a decision on whether to participate. While the search project failed in its attempt to locate a specific mine site, the research team believes that this is not a rejection of the actual project but rather extreme caution because of the uncertainty within the UMWA.

Jan 1, 1978

By W. W. Adams

The first full year of the second World War for the United States presented a picture of the metal-and nonmetal-mining 4 industry which, without proper analysis and explanation, would convey a distorted view of achievements during 1942, especially because employment at gold and silver (lode and placer) mines-the largest group-declined to such an extent that the over-all totals for the country were reduced even though increases were made at mines producing copper, lead-zinc, iron, miscellaneous metals, and non-metals. A complete panorama of the metal-and nonmetal-mining industry, exclusive of coal mining, reveals a decrease in the number of men employed, the man-hours of employment, and the accident-frequency rates. Were the gold and silver (lode and placer) mines to be considered as a separate category; it would be seen that the number of men employed at all the other groups of mines increased appreciably over 1941. These other increases must be considered important, since these mines produced the vital war minerals that made valuable contributions to the military successes of the United States and its Allies during the year. A separate analysis of each of the various groups of mines may be found elsewhere in this bulletin. For the purpose of maintaining continuity in this series of bulletins, however, the discussion in this introduction will be confined to the entire metal-and nonmetal-mining industry (excluding coal mining, for which a separate bulletin, No. 462, has been published).

Jan 1, 1945

By Johan Svard

"Two years of field testing have shown that blasting results are improved both in surface and underground applications when Nitro Nobel electronic detonators are used. The delay times canbe chosen with an accuracy of 1 millisecond over the entire time range (1 to 6250 ms). Since ordinary.high explosives have detonation velocities of up to 6000 metres/second, these high velocities make accurate and flexible delay times very interesting."

Jan 1, 1992

By Ian Vaz, Takefumi Takuma, Rafael Holcombe, Chris DellAringa

"This paper will discuss the successful installation of seawalls for the first phase of a project in Long Beach in California known as the Naples Island Permanent Seawall Repair – Phase 1. How an unconventional method of pile driving resulted in the reduction of the duration of the project while using less space and maintaining minimal noise impacts to accommodate neighbors will also be discussed. Included in the paper will be how non-vibratory equipment used on this project also significantly minimized the risk of disturbances as well as settlement on residential properties; which in turn greatly reduced the risk of damage to existing structures. The first phase of a 6-phase project along a section of the canals with tight clearances and proximity to residents included the installation of a 1,912 linear-foot steel sheet pile wall system in front of the existing deteriorating walls from January until March 2015.INTRODUCTIONThis project was located in the Naples Island neighborhood of Long Beach in southern Los Angeles County, California. After 80 years of the same seawall structures lining the canals of this beautiful neighborhood, the City of Long Beach Department of Public Works decided that it was time to better protect the area’s multi-million dollar homes by repairing its crumbling seawalls. The City realized that the walls will only become worse due in part to several concerns, including bending failure for the already deflecting walls. According to the City, certain sections of the walls had a significant risk of global failure if the area experienced a “moderate” near-source earthquake (City of Long Beach, CA, 2014b). Although the seawalls were in need of major repair, this would not be simple. Due to the tight clearances of the seawalls between the homes and canals, installation would be difficult with heavy, conventional construction equipment.Phase 1 of the project involved installing sheet piles on the water side in front of existing and aging vertical concrete seawalls between the Ravenna and Toledo Bridges along the Rivo Alto Canal. See Figure 1 for the General Plan for Phase 1. Financing for this project by the City’s Tidelands Capital Improvement’s Division allowed the construction to begin in a timely manner. However, the challenges for the City included regulatory restraints that further complicated the construction in terms of the duration of the project due in part to numerous regulations from several regulatory agencies."

Jan 1, 2016

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018

By T Hicks

Designers of mining facilities play a significant role in defining the overall mine greenhouse gas emissions performance. This demands an appreciation of all the greenhouse gas emissions sources, including Scope 3 emissions, which will form an increasing fraction of the emissions as we transition our generation sources to renewable energy. Traditionally overland conveyors are designed to operate as fast as practical, and through this approach, achieve relative minimisation of: conveyor belt tensions; belt width; mechanical equipment masses; structural steel quantities; and concrete quantities. It is well understood that higher belt speeds reduce capital cost and improve project economics. Operating at higher speeds introduces operating costs through system energy losses and increased wear rates. This paper assesses the life cycle greenhouse gas emissions for a typical iron ore overland conveyor to demonstrate how the design criteria and engineering decisions impact greenhouse gas emissions and project economics. An analysis of the decarbonisation potential and project economics using a range of operational parameters has been completed, developing a marginal abatement cost for each system configuration, creating a basis for integration of low emission overland conveyor designs as part of the broader facility decarbonisation strategy.

Sep 1, 2024

By Ruan Chi, Zhenyue Zhang, Zhengyan He

In order to understand what governs the leaching of exchangeable rare earth (RE) and impurities and enhance the RE leaching process, the effects of the concentration of ammonium sulfate, pH and leaching temperature on the migration of RE and aluminum (Al) during the leaching of weathered crust elution-deposited rare earth ore was studied. The elution curves for ammonium ion (NH4 +) were also studied to reduce the consumption of the leaching agent. It was found that a high concentration of leaching agent can enhance the leaching process of RE and Al, reduce the breakthrough volume of NH4 + and more rapidly obtain the equilibrium of NH4 +. However, excessive leaching agent can both increase the cost and the burden on the environment. There is almost no variation on the elution curves of RE and Al in the pH range of 4-8 and control of the pH of the leaching agent can be omitted. It is better for the leaching work to be done in summer since higher temperatures can enhance the RE leaching process and improve the use ratio of ammonium. Using 0.1 mol/L ammonium sulfate for leaching 250 g RE ore, 95.42% RE extraction can be obtained when the volume of leachate is 102.6 mL. At this moment, only 18.17% of NH4 + is used to exchange RE and 49.22% of NH4 + is left in the leachate that can be reused as leaching agent by replenishing ammonium sulfate. The results of our studies can provide theoretical guidance for high efficiency and low consumption exploitation of RE ores.

Jan 1, 2016

By I. Peerawattuk

Growing demand for Li-based battery technologies is leading to an unprecedented growth in the lithium industry. Although innovation in battery technologies has pushed lithium into the spotlight, lithium was not always known for its application in batteries. The primary use of lithium—prior to the introduction of commercial lithium-ion batteries in the early 2000s—was in the ceramics, glass, grease, and the medical industry. Before being converted into usable forms, lithium products must be upgraded from the raw material. Processes for recovering lithium may involve: thermal treatment, water leaching, solar evaporation, ion exchange, carbonation, and electrodialysis. Presented, is a historical review of lithium applications and the different techniques of converting lithium-rich minerals and brines into usable products with additional discussion on future lithium extraction processes.

By K. Lillkung, J. Kourunen, M. Latva-Kokko

"Carbon-in-leach (CIL) and carbon-in-pulp (CIP) processes utilize activated carbon to adsorb solubilized gold for recovery. Due to carbon attrition and non-ideal carbon management, however, some of the gold is lost in carbon fines and to the solution. The carbon attrition mechanism inside CIL/CIP reactors is mainly abrasion-related. This is critical to gold loss since gold loading takes place predominantly in the outer shell of the carbon particles. Thus fine carbon dust has a relatively high gold content and such a small particle size that it cannot be captured with safety screens. The attrition rate depends on ore and carbon characteristics, but it is always proportional to the mixing power intensity. This rate can be minimized by continuous suspension level measurement and control of agitation speed. In addition, a novel tank bottom structure can significantly reduce the required mixing power input compared to a flat bottom tank. A major challenge in carbon management is infrequent and inaccurate measurement of carbon concentration in the reactors. In order to reduce soluble gold losses by means of improved carbon management, Outotec has been developing a continuous in-situ measurement for carbon concentration that is tolerant to changes in slurry density.INTRODUCTION Cyanide leaching has been utilized since the late 19th century as a standard technology for hydrometallurgical gold production. Since then, gold and silver recovery rates have increased due to technological development, but very similar recovery methods are still being used. The original recovery method was to use zinc precipitation – similar to the Merrill-Crowe process, which is still common for feed materials with low throughput and high silver content. However, in most cases, activated carbon recovery is preferred due to its improved efficiency. The carbon-in-pulp process (CIP) and its modification, carbon-in-leach (CIL), have a lower residual soluble gold level and are not similarly affected by soluble base metals. The main alternative for the use of carbon is ion exchange resins. The principle of resin processes is similar to the CIL/CIP processes, with a different type of adsorbent material. Carbon processes are usually preferred over resin processes due to the significantly higher cost of resin material and the possibility to use simpler, well-established technology with carbon processes."

Jan 1, 2017

By Charles W. Merrill

The U .S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reducing demand. This paper examines possible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Jan 1, 1965

By Charles W. Merrill

The U.S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reducing demand. This paper examines possible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Jan 1, 1965

By K. J. Martchek

"This introductory presentation will highlight recent efforts to quantify the positive value of recycling metals such as aluminum, magnesium, lead, zinc, nickel and copper in relation to the three pillars of ""sustainable development"" - environmental protection, economic development and improve social consequences.This presentation will provide an overview of life cycle assessment profiles increasingly being utilized by customers, regulators and environmental advocacy groups to holistically evaluate the environmental performance of materials and products. The environmental profiles of prodi.lcts containing recycled metal will be presented based on rules established by the International Organization for Standardization (ISO).Significant to the life cycle profile of metal products is recent confirmation. that recycling has the potential to reduce materials production energy consumption by 95% for aluminum, 80""/o for magnesium and lead, 75% for zinc, and 70% for copper. Furthermore, . ""metals are eminently and repeatedly recyclable, while maintaining all their properties (1 ). "" Their durability relative to many hydrocarbon based materials enhance .their life cycle performance. However, the persistence of metals when dispersed into our natural environmental makes recovery and recycling particularly important Overall, when considering life cycle effects, recycling is critical to a sustainable future for metal products.Finally, regional and international regulations will be highlighted which will effect the efficient recovery and recycle of metals and their overall contribution to environinental protection, economic development and the enhancement of society."

Jan 1, 2000

By J. W. Evans

Mathematical modeling has now become a standard technique in the development of new technology and the improvement of existing technology in the processing industries. Physical modeling has a longer history but a smaller following at present. The paper reviews some examples of the application of both types of modeling in non-ferrous metal extraction, particularly within the copper and aluminum industries. The objective is to show that well founded models can lead to results that have practical consequence in scaleup, design and operation.

Jan 1, 1993

By L. Zhou, L. Yuan, D. Bahrami, Y. Xue

Underground mine accidents, such as mine fires, remain a health and safety risk to mine workers. Researchers at the National Institute for Occupational Safety and Health (NIOSH) are developing a data-driven, predictive model for characterizing the location and size of unknown underground fires. This study examines applying a machine learning-based model to predict fire size and location in a large underground metal mine based on hypothetical scenarios on the model performance. The results show that the size and location of an unknown fire can be determined with over 80% and 90% accuracy, respectively, and potentially help to reduce the risk of hazardous conditions for emergency response.

Feb 1, 2024

By J. A. Scott, K. Moreau, H. Shang

"Trials of automated technology at underground mine sites around the world have reported increased production and the potential for lower energy consumption. Autonomous mining eliminates a range of delays related to operator downtime and travel to the workface and facilitates continuous operation in conditions that are unsafe for workers. Automation also introduces complexities and safety hazards arising from equipment–personnel interactions; automated processes must be isolated from other stope-cycle–related activities such as production drilling, development, loading, and backfilling, poten¬tially requiring changes to the mine design to maintain an efficient and safe operation. This paper reviews and discusses the implementation of automated equipment in deep underground mining operations and the challenges and advantages associated with the technology. ¦ KEYWORDS Automated equipment, Emissions reduction, Energy, Productivity, Sustainability, Technology, Underground mines RÉSUMÉ Des essais de technologies automatisées dans des sites miniers souterrains aux quatre coins du monde ont indiqué une production accrue et la possibilité de réduire la consommation d’énergie. L’exploitation minière autonome élimine tout un éventail de retards liés aux temps d’immobilisation des opérateurs et aux déplacements vers le front de taille, et facilite l’exploitation continue dans des conditions qui s’avèrent peu sécurisées pour les travailleurs. L’automatisation introduit également des complexités et des risques pour la sécurité, qui surviennent en raison des interactions entre l’équipement et le personnel. On recommande d’isoler les procédés automatisés des autres activités liées au cycle des chantiers telles que le forage de production, le développement, le chargement et le remblai, ce qui pourrait entraîner des changements au niveau de la conception de la mine afin de préserver rendement et sécurité dans l’exploitation. Cet article examine et aborde la mise en oeuvre de l’équipement automatisé dans des exploitations minières souterraines profondes, ainsi que les enjeux et les avantages associés à cette technologie. ¦ MOTS CLÉS durabilité, énergie, équipement automatisé, mines souterraines, productivité, réduction des émissions, technologieINTRODUCTION As the mining industry continues to exhaust easily accessible orebodies, the need for efficient, deep (typically below 2,500 m) mine operations increases (Atlas Copco, 2013a); however, the mining process can become economically infeasible at great depths because operation costs drastically increase. This has resulted in investigations into automating mining operations as the industry strives for improved productivity (Schunnesson, Gustafson, & Kumar, 2009) and ways to remove personnel from hazardous work areas."

Jan 1, 2019

By R. K. Singhal

A variety of mining equipment is used in the mining of oil sands by surface mining. This includes bucket wheel excavators, draglines, hydraulic shovels and off-highway trucks. This paper examines the existing mining schemes and equipment used Peculiarities of oil sands surface mining and their influence on equipment selection, utilization and mining schemes are described. Recent developments undertaken to improve mine productivity are also dealt with together with some notes on proposed measures to obtain further gains in productivity.

Jan 1, 1985

By Jon C. Volkwein

The Bureau of Mines, Foster-Miller Inc., and Beaver Creek Coal Co. have evaluated the ability of a new system to ventilate a 40-ft-deep cut. A remote-control continuous-mining machine, in a 7-ft-thick seam, with exhausting brattice was fitted with an improved sprayfan system plus additional forward and reverse pointing sprays. Static and dynamic tests using tracer gas were conducted in a full-scale model and under-ground to measure the effectiveness of exhaust face ventilation for various deep-cutting mine and spray configurations. When compared to a lO-ft primary ventilation brattice, the extended-cut spray system consistently provided better face ventilation at all configurations up to and including a 40-ft brattice setback. The system also provided good dust protection and visibility for the machine operator. Another safety advantage is the elimination of the need to set temporary roof supports to maintain the ventilation brattice.

Jan 1, 1985

By Charles L. Harness

Fifty years ago, the belief that "fillers" were added to paints for the sole purpose of diluting and cheapening the pigment may have been justified; but paint technology has made tremendous progress since that time, and today both the manufacturer and the consumer know that the judicious use of fillers may add desirable properties to a paint that cannot be introduced in any other way. A growing respect for these accessory materials has led to the use of the more euphemistic term "extender." The names "extender" and "filler" are to a considerable degree synonymous. The newer term, "extender," is adopted in this paper, though it is actually no more descriptive than the older name. Stewart's3/ definition of extender is: "A cheap pigment, usually of an inert type, used to extend or increase the bulk of a paint, thus reducing its unit cost. Extenders are also used to adjust the consistency of a paint and to let down colored pigments of great tinting strength. The use of an extender in a paint does not necessarily mean the resultant product will be inferior. In fact, extenders sometimes, improve -certain characteristics of a film." All extenders are not cheap, as, for example, wet-ground mica and diatomite. Research in the, use of extenders (also sometimes called "inerts") has been one of the host active branches of study in the paint field; and many thousands of dollars have been spent in establishing the physical and chemical characteristics required of various natural mineral extenders for numerous paint formulas

Jan 1, 1943

By D. Emadi

The ASTM B108 Mould and a Modified Mould were used to cast test bars under a variety of conditions: mould and pouring temperatures, mould coating and tilt. Mechanical properties were determined in the as-cast and heat-treated conditions. The ASTM Mould is less sensitive to casting variables. Enlarging the gating system and adding additional gates to the ASTM mould can improve properties in the tilt position. The reproducibility of properties in as-cast and T6 heat treated bars was investigated.

Jan 1, 2004

By S A. Ravishankar, W Perez

Flotation is one of the main concentration processes to purify kaolin clay via the removal of naturally occurring impurity minerals containing Ti and Fe. Currently, there are two types of collector chemistries used in the industry to float coloured impurity minerals. These are traditional tall oil fatty acids (TOFA) and specialty hydroxamate (AHX) based collectors. AHX based collectors have long been known to be the most selective collectors to float Ti and Fe based coloured impurity minerals (CIMs) as compared to TOFA based systems. AHX based collectors provide, not only improved selectivity and simplified process, but also more importantly, make it possible to treat certain kaolin resources that do not respond to standard TOFA systems. However, the relatively higher cost of straight AHX collectors has restricted broader application of these collectors in kaolin clay and other oxide flotation applications for a long time. Recent technological advancements, in both making and formulating AHX products more economically, increased the usage of these collectors in kaolin applications. Modified AHX products offer more economical alternatives and process options to provide high purity kaolin clay products for specialty applications based on cost-performance criteria. In this paper, the flotation performance of a series of newly developed AHX formulations is provided along with the characteristics of AHX flotation in general. In addition, flotation performance of earlier AHX collectors is provided based on published literature as background data.

Jan 1, 2005