Search Documents

By Kenneth Cottingham

The number of wells drilled in Ohio in 1943 was slightly in excess of the number drilled in 1942. Compared with the average annual completions for the five years preceding, the year 1943 was short 11 per cent, hut the average initial volume of gas wells was considerably improved. In 1942 the average initial open flow per gas well was 668 M cu. ft., whereas in 1943 the average was 913 M cu. ft. Although no large gas-producing areas were discovered during the year under review, some 30 small pools were found in 17 of the counties of eastern Ohio. These new pools averaged about 300 acres each, and most of them were not extensions but were separate pools adjacent to older production. The Clinton sand furnished most of these discoveries, although six were from the Berea, one was Newburg, and three were shallow sands. No discoveries were made outside former producing counties, and there was no new development the Trenton area of western Ohio. The number of oil wells decreased from 181 drilled in 1942, to 170 in the year 1943. The production of Pennsylvania-grade oil increased 7644 bbl. The total Corning production, however, decreased 91,325 bbl. The present price of Corning-grade oil, $1.31 per bbl., is too low, in the opinion of the operator, to justify exploration. Until something is done in correcting the price level of Corning grade, the production probably will continue to decline. The oil industry in Ohio is making a concentrated effort toward increased production and improved methods of recovering Pennsylvania-grade oil, and a.s this report is written a research and engineering program is being formulated for the benefit and information of the various producers of that grade in Ohio.

Jan 1, 1944

During the past eight years a vigorous drilling campaign resulted in large increases in the reserves of both copper and silver-lead-zinc ores.As a result the Company initiated an increased production programme.Some major capital works have been completed, others are in progress and more are needed to achieve the proposed daily throughput of 14,400 tons. The increased ore potential justified a copper refinery which has been constructed at Townsville. The increased production rate achieved to date, combined with improved techniques and greater mechanization, is assisting the Company to combat the general inflationary trends caused by increased costs for labour and materials.INTRODUCTION"Today we are armed with better weapons in our fight for lowered costs and greater efficiency, but we must not flag in our efforts to improve." Such was the resolution expressed by Mr. K. B. Gross, then General Manager of the Company, in his review lecture delivered to the First Ordinary Meeting of The Australasian Institute of Mining and Metallurgy at Mount Isa on 18th August, 1952. This present review of the period 1952 to 1960 records our efforts to fulfil this resolution. At the th:ne of Mr. Gross's statement,copper production was commencing in earnest. Although the importance of Mount Isa's copper orebodies was well recognized, the major discoveries which led to Mount Isa's emergence as Australia's premier copper mining and smelting operation were not known. These ore discoveries and their subsequent development are the major factors which warrant a further review of the Company's progress.The increased magnitude of the Company's operations is illustrated on graphs of Tons of Ore Treated (Fig. 1), Metals in Products (Fig. 2), Water Consumption (Fig. 3)...

Jan 1, 1961

By Claude H. P. Lupis, John F. Elliott

The classic Siez~erts' technique has been employed to determine the solubility of oxygen in liquid pure silver and the effect on the oxygen solubility of solute metal additions to liquid silver. The results indicate that oxygen deviates slightly from Sieverts' law in pure silver as = 3.9. Gold, platinum, md palladium decrease the solubility of oxygen in silver. First-order free energy, enthalpy, md entropy interaction coefficients are determined from the data. An important aspect in the establishment of the formalisms to be applied to represent the thermody-namic behavior of components of solutions is the accuracy of the experimentally determined thermody-namic properties. Wagner developed the first-order free energy interaction coefficient.' Recent papers2'3 extend the treatment formally to other thermodynamic properties and define the second- and higher-order interaction coefficients. A current communication4 considers in some depth the requirements and limitations imposed because of experimental error on the use of several formalisms now under active consideration in the field. This communication reports the results of an experimental study of the behavior of oxygen in liquid silver alloys that was carried out concurrently with the development of Refs. 2 and 3 with the hope of providing sufficiently precise information so that enthalpy and entropy interaction coefficients could be determined. THE EXPERIMENTS The Sieverts technique was employed using an improved design of the reaction bulb over that developed originally by Humbert5 and subsequently improved by pehlke6 and Weinstein.7 The Vycor reaction bulb as shown in Fig. 1 was air-cooled and contained a port for the thermocouple angling off to one side and a vertical port for connections to the gas supply and

Jan 1, 1969

By Balesh W. Konda, Andrew B. Cecala, George W. Klinowski

Methane ignitions continue to be a major concern to the longwall mining industry. In spite of numerous advances in technology over the past decade, there has not been a measurable reduction in the number of longwall face ignitions. These ignitions will continue to be a problem as deeper and gassier seams are mined, as production rates are increased through numerous improvements in longwall mining equipment, and as the output of the workforce increases due to improved management-labor relations. It is necessary to know methane liberations, emissions, and flow patterns in order to effectively deal with it and to design control technology to reduce the occurrence of longwall face ignitions. A cooperative research project between the Bureau of Mines and the Canada Centre for Mineral and Energy Technology (CANMET) has been established to address longwall methane problems. The initial direction of this work was to look at methane flow patterns during the entire longwall mining process, and more specifically to examine and compare methane levels and flow patterns for advance and retreat methods of longwall mining. Both advance and retreat longwall mining is practiced in the Sydney coal fields in Nova Scotia. In 1986, a study was performed on advancing longwall panels at the Lingan Colliery, and a similar study was recently completed at the Phalen Colliery on a retreating panel. Methane monitors were placed at various locations along the face, intake, return, and bleeder airways. Handheld methane monitors were also used upstream and downstream of the shearer mining machine. This setup allowed a determination of methane sources on the longwall panels, including: liberation from cutting with the shearer mining machine, emissions from the coal seam along the face, emissions from the gob area, and methane already in the intake air. The results from both studies are reported and the differences between the two longwall mining methods compared.

Jan 1, 1989

By Stewart Coleman, Thomas W. Moore, H. D. Wilde

It is recognized that in the early days of the petroleum industry oil was produced with practically no scientific or fundamental knowledge of the laws and principles governing its extraction from the ground. Only a few, if any, of those exploiting the oil resources made any effort to collect accurate scientific information. There was little need for it, for as is frequently the case where the supply of a natural resource appears inexhaustible and is greater than the demand, large profits were possible from merely skimming the surface with little regard to the efficiency or thoroughness with which the oil was obtained. With this policy in force, great quantities of gas were wasted and when the reservoirs ceased producing by natural means they still contained a large fraetion of the oil originally in them. The present tendency in the industry is toward conserving existing oil reserves. In order that greater percentages of the oil present in the ground may be recovered, efforts are being made to improve production methods and to rework depleted fields. If the production methods are to be improved intelligently it is essential that the fundamental laws be known and understood, consequently large amounts of money and effort are being spent in gathering data that will serve to define and interpret these laws. A great deal of attention is being focussed on the study of the motion of oil through an oil-bearing sand, the forces that cause it to move and the factors that affect its motion. It is recognized that one of the important factors is pressure, but its quantitative effect is not known. In a given field the rate of production declines with time and so does the rock pressure. Furthermore, a comparison of different fields shows, as a

Jan 1, 1930

By R. Tessier, R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. The paper presents findings in the on-going testing of various sizes and shapes of grinding media. Breakage rates are used as an aid to assess the effect of grinding media. Results of empirical and phenomenological analyses demonstrate the importance of adequate selection of media sizes on the milling operation.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mine near Bathurst, New-Brunswick. The No. 12 ore body is an extremely fine grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite. The operation is currently processing 10,500 tonnes of ore per day in conventional crushing, grinding, differential flotation and dewatering circuits. Details on the circuit can be found elsewhere (e.g. Hendriks and Ounpuu, 1985; Grant et al., 1991).The mill has operated for more than 25 years and despite the past milling experience, there has been much disagreement as to the required grind size. Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37µm) and averaged slightly over 71%in1992. Results from mineralogical analysis (Petruk and Schnarr,1981; Coleman, 1988), Brunswick metallurgical laboratory (Grant et al., 1991; Shannon et al., 1992) and Lakefield pilot plant tests (Hendriks, 1984; Hendriks and Ounpuu, 1985) clearly indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15-25µm range."

Jan 1, 1993

By Y Pan

The recycling of steel is a crucial aspect of the shift toward a sustainable metals industry. The emphasis on steel recycling through the introduction of the scrap based mini-mill concept is also matched with a desire for greater product quality and reduced environmental impact, which, in turn, has generated important innovations. There have been significant advances in the technology for recycling steel over the last 20 years and this paper will provide an overview of these developments and discuss future directions in steel recycling including scrap management, control of tramp elements, electric arc furnace technology and ladle metallurgy.

Jan 1, 2004

By J. L. Jernegan

In a former paper laid before the Institute, entitled Lead and Silver Smelting in Chicago, I endeavored to give a description of the manner in which argentiferous lead ores from the far West were treated in that city, and also described the method employed in the desilverization of the silver-lead produced from the ores. It will perhaps be remembered, that very siliceous ores, principally from the Emma mine, Utah, containing over 40 per cent. of silicic acid, were then being treated at the works of the Chicago Silver Smelting and Refining Company in the reverberatory furnace, with the use of metallic iron, in the form of borings, as a precipitating medium for the lead ; and that the extraction of the silver from the resulting bullion was effected by the Balbach process. The Swansea Works, also the works at Brighton, just outside of this city, and those of S. P. Lunt, were at that time treating ore of a similar character by the same method. The inadequacy of the process for the ores then under treatment was, in a manner, pointed out by me in the paper above referred to. Since the time of its writing, many and important improvements have been made in the metallurgical treatment of western ores in Chicago. Most ores are now roasted previous to reduction, and the latter operation is conducted in the shaftfurnace instead of the reverberatory. Such is the fact at least at the Swansea Works, the largest in the city, and here it was where the first steps were taken in this direction. In selecting these works as the subject of this paper, I am in hopes that the description given of the varions metallurgical operations, as they are there now conducted, will serve to give an idea of the improvements introduced

By Samuel Daniels

Aluminum-base alloys containing small amounts of copper and magnesium possess but ordinary physical properties as sand cast, but may be treated to give a remarkable range of tensile values and of Brinell hardness. The high-copper (4.5 per cent.) duralumins must be given a protracted treatment which in nature resembles the malleableizing of white cast iron; the low-copper (2.25 per cent.) duralumins develop an excellent combination of strength and ductility with a treatment which requires a maximum of 5 hr. to be completed. THE wrought alloys of aluminum with small amounts of copper and of magnesium have, with the development of the automotive and aircraft industries, sprung into prominence through the medium of duralumin; but the cast alloys remained in the background because their possibilities in the heat-treated condition were either not recognized or not fully investigated. In 1919, the Bureau of Standards published a preliminary survey1 of this field, which pointed out that, in general, the ultimate strength and the percentage of elongation of the alloys of aluminum with and without magnesium could be improved by so simple a treatment as heating to 932° F. (500° C.) for 2 hr., cooling in, air, and aging at room temperature for several days. British investigators, too, working with chill-cast material, found that " considerable improvement in the mechanical properties of copper-aluminum alloys' may be obtained from suitable heat treatment applied to castings."2 Jeffries and Gibson3 made the first contribution to the literature dealing exclusively with the heat treatment of sand-cast aluminum-base alloys, describing the effect of small additions or of combinations of copper, magnesium, and iron on the response to a short heat treatment comprising heating at 932° F. in a

Jan 7, 1924

By J. L. Jernegan

IN a former paper laid before the Institute, entitled Lead and Silver Smelting in Chicago, I endeavored to give a description of the manner in which argentiferous lead ores from the far West were treated in that city, and also described the method employed in the desilverization of the silver-lead produced from the ores. It will perhaps be remembered, that very siliceous ores, principally from the Emma mine, Utah, containing over 40 per cent. of silicic acid, were then being treated at the works of the Chicago Silver Smelting and Refining Company in the reverberatory furnace, with the use of metallic iron, in the form of borings, as a precipitating medium for the lead ; and that the extraction of the silver from the resulting bullion was effected by the Balbach process. The Swansea Works, also the works at Brighton, just outside of this city, and those of S. P. Lunt, were at that time treating ore of a similar character by the same method. The inadequacy of the process for the ores then under treatment was, in a manner, pointed out by me in the paper above referred to. Since the time of its writing, many and important improvements have been made in the metallurgical treatment of Western ores in Chicago. Most ores are now roasted previous to reduction, and the latter operation is conducted in the shaft-furnace instead of the reverberatory. Such is the fact at least at the Swansea Works, the largest in the city, and here it was where the first steps were taken in this direction. In selecting these works as the subject of this paper, I am in hopes that the description given of the various metallurgical operations, as they are there now conducted, will serve to give an idea of the improvements introduced

Jan 1, 1876

By Iain Finnie

This report is in three parts. The first part presents a review of theoretical models which have been developed to study removal operations for various types of materials. In the second part, a brief summary is given of coal cutting research. The majority of this work has been carried out in Britain using chisel type bits rather than the conical picks which are in general use in this country. However, a comparison of specific energies measured for conical picks in the laboratory and in the mine shows very encouraging correspondence. In the third part of the report, analytical models for coal cutting by picks are suggested. An extension of the British "tensile breakage" theory, developed for chisels, is given for picks. The role of crushing and cutting in coal removal is discussed as a theory which combines the two processes is shown to give reasonable predictions for specific energy requirements. Finally, directions in which the existing theory could be improved are presented and the need for further research is emphasized.

Jan 1, 1977

By So-Yeong Lee, Moosang Lee, Seung Hwan Ahn, Ho-Sang Sohn, Jongshin Chang

It is necessary to understand the characteristics, phase changes and chemical reactions of flue dusts introduced from a furnace to an off-gas line in order to achieve the stable operation and the improvement. This study is to develop the dust reaction model for chemical reactions of dusts in an uptake shaft of smelting furnace and a waste heat boiler. Phase equilibria and reaction paths in this system were determined by thermodynamic calculation with experimental and industrial data. The oxidation reaction rate of dusts was determined by the gas film mass transfer controlling. And the sulfation reaction rate was evaluated by the unreacted shrinking core model. Kinetic parameters were estimated by reference data including industrial ones. The present study with the developed model shows various effects of temperatures, dust particle sizes, and O2 gas partial pressures on dust reactions. INTRODUCTION The flue dusts from a copper smelting furnace move along a furnace off-gas stream into an uptake shaft and a waste heat boiler (WHB) and electrostatic precipitator(s). It is necessary to control the dust quality in order to stabilize the operation because the sticking behaviors differ depending on the phase of dusts. Phase changes of dusts are caused by chemical reactions at given conditions such as temperature and partial pressure of gases. Therefore, it is required to understand the phase changes and chemical reactions of dusts in order to perform the improvement and stable operation. The present study carried out the investigation to understand their fundamental knowledge. Especially, this study was focused on the kinetics of chemical reactions of flue dusts, developed the model. In particular, the scope of development and utilization of the model was defined as the uptake shaft of the Mitsubishi S furnace and the S-WHB radiation section in the Onsan smelter. Information needed for the modeling work referred to data from these processes.

Jan 1, 2019

By Randolph A. Pax

"The internal operation of a tumbling mill is a very hostile environment and precludes the sustainable operation of internal sensors to measure the mechanisms of charge motion and breakage events. Instead indirect methodologies are required to expand the current understanding developed within a framework of perfect mixing of the mill contents. A number of measurement approaches have been successfully used to explore the operation of SAG mills including strain instrumented lifter bolts, mill shell strain measurement and thermal (energy balance) of operating mills.Early acoustics measurement was developed by Hardinge using a 'microphone' located close to the expected toe location. This signal was an indicator of the mill fill. Improvements were implemented with the use of two microphones straddling the toe location to try to increase the sensitivity of the measurement and reduce ambiguities. Further improvements included a filtered signal indicative of steel interactions. Unfortunately, the mechanisms of signal generation and the complexity of the processes do not provide a consistent signal.In recent years, advanced acoustic measurement using arrays of microphones utilising signal processing techniques have been implemented as SmartNoise and validated on over 30 mills. This paper will discuss the results obtained with signals such as water holdup, mill shell steel hits and two each of the toe and shoulder angles. An estimate of the internal mill component wear rates is also accessible.Advanced acoustic measurements with wide bandwidths when combined with physics models and process understanding has achieved a step change in the understanding of the dynamic internal operation of a tumbling mills on time scales of 80 ms. These techniques have been used extensively on SAG mills, but have also been applied to FAG and ball mills. Acoustic measurement is used for the rapid diagnosis of mill conditions and holistic control for optimisation and stability."

Jan 1, 2016

By Francisco Sena Leite, Vincius Miranda, PhD Machado Leite, PhD Pinto, Raquel Carvalhinha, Alexandre Julio, Dorival de Carvalho

Rock blasting, in particularly the drilling process, is one of the first processes in the stage of rock fragmentation and plays a fundamental role by influencing all the following stages. Given its importance, some proposals to optimize this process have been presented over the last few years. These proposals, while having different approaches, aim (in a large part) to minimize the costs of drilling and blasting respecting the limits of fragmentation required by primary crushing. Reviewing some recent articles leads us to an enriching experience, since the authors of these articles clearly model the problem, but do not address the mathematical solution of these models, which in turn, given their non-linear nature, have no directly and easy solution. Simple and even robust optimizers present in the market show different results and often do not converge to a single solution. To address this problem, an adapted gradient heuristicbased model was developed to try to find optimum values. Heuristics search for values of stemming, subdrilling, burden and spacing that minimize the costs of blasting and drilling. This search, which by the nature of the heuristic moves the solution in the direction of the gradient with maximum decrease to find optimal solution, found values that in turn, when compared with values presented by market solutions not only equaled them as, in some situations, even improved the proposed solution. The algorithm was tested and validated on the field, and although the results have already been presented in papers published in the last year by the authors of this paper, it is now presented with its mathematical formulation and comparison with the other solutions. This approach is expected to be able to improve (and even demystify) the process of pattern expansion and be the basis for future work in the continuation of the optimization process.

Jan 1, 2019

By S. C. Westerfeld

The original patent for the gyratory crusher was granted to Philetus W. Gates in 1881. This first crusher was used by the Buffalo Cement Co. At the time these early gyratory crushers were developed all mining and quarrying, either underground or open pit, was done by hand; tonnages generally were small and product specifications simple and liberal. Likewise plants were small and demands for small product sizes practically nonexistent. In addition to substantial amounts of hand labor, the available material handling equipment was small, simple, and not suited to handling large run of mine ore. Mine can, cable ways, or belt conveyon transporting crushed material to the mill had limited capacity per hour. At the turn of the century the largest Gates crusher, the No. 9, had a receiving opening of 21 x 48 in. with a three-arm spider and a 21 x 80-in. opening with a two-arm spider. The steam shovel began to change the entire picture of open pit quarrying. As a result of the use of steam shovels around 1910 crushers with 48-in. receiving openings were built; thus it can be seen that the basic gyratory crusher was developed prior to World War I. The improvement of the internal combustion engine and the use of pneumatic tires created a new set of operating conditions. Early mines were small, using shrinkage stoping and small mine can. The capacity of material handling was small, limiting the size of the largest piece and the feed rate. Improved material handling resulted in more and more large open pit mines with large shovels and a tremendous increase in the size of off road or mine haul trucks or rail can. Primary gyratory crushers also increased with receiving openings as large as 60 in. and connected hp of 1,000.

Jan 1, 1985

By Lar Liljeblad

"As demands upon the earth's natural resources continue to grow, exploration companies, mining organizations and others face the problem of the need to tackle increasingly more difficult strata to open up new reserves. Innovations in materials technology and tool design have steadily improved this capability, but none perhaps so drastically as a recently introduced cemented carbide in which tool wear resistance and/or toughness can be tailored precisely to the user's drilling needs.Introduction Until about forty years ago, the bulk of rock-drilling operations had to be carried out with hardened steels. Short life between re-grinds was common especially in abrasive rock formations. Shortly after World War II, Sandvik, Sweden, pioneered the development of sintered (cemented) carbide-tipped steel tools as a means of improving drill tool life. The new material was a composite of tungsten carbide and cobalt, the latter acting as a 'cement' to bind the wear-resistant carbide grains together, and the composite, in turn, was brazed to the steel. The immediate effect was a 100-fold increase in the service life of the tool.Intractable ProblemsWhile the carbide-tipped tools served the mining and quarrying industries admirably there were, nonetheless, some seemingly intractable limitations. The greater the wear resistance of the material - the quality for which it is selected - the more brittle it is. Also, rocks vary widely in hardness and abrasiveness and no single tool, either in terms of material or shape, meets every need. Specifically, for fast penetration of non-abrasive rock, toughness must be combined with a relatively sharp tool prome. Highly abrasive rock, on the other hand, demands a substantially broad area of extremely wear-resistant material on the tool if long bit life is to be assured. Between these extremes there are innumerable variations in rock"

Jan 1, 1991

By S Doyle

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Macraes gold mine in Otago, New Zealand, is developed along the central portion of the Hyde-Macraes Shear Zone (HMSZ), which dips gently to the NE, and is traceable over 30 km of strike, before disappearing under tertiary cover. Mineralisation is most intensely developed along the hanging wall shear, which defines the upper limit of the shear zone, although significant packages of quartz vein arrays and mineralised shears occur sporadically beneath the hanging wall shear.The Macraes gold mine is now in its 25th year of operation, well beyond the projected mine life at the time of commissioning in 1990, and currently contains over triple the measured and indicated resource inventory that was defined at start up. The extended mine life and resource growth has been driven by exploration and resource development success, efficient low-cost mining and processing, improving gold price, as well as an ethos of continuous improvement.The emphasis of Oceanagold’s exploration and resource development has shifted over time; from hanging-wall-focused mapping, soil sampling and step-out drilling, through exploitation of previously drilled stockwork mineralisation, to the pursuit of blind, higher-grade underground targets.Mineralisation within the HMSZ remains open at depth, and the regional potential has not been fully tested. Given the relatively low-grade of gold mineralisation at Macraes, the consideration of tungsten as a supplementary co-product provides an exciting opportunity.CITATION:Moore, J and Doyle, S, 2015. Resource definition in the world-class Macraes gold mine, New Zealand, in Proceedings PACRIM 2015 Congress, pp 557–564 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Marcia Harris, Richard Mainiero

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

Jan 1, 2004

By Richard J. Mainiero, Marcia L. Harris

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

By G. H. Blackwell, A. J. Sinclair

"The main components of a ""PC” -based mineral inventory system are described in a sequence common to many real reserve/ resource estimation projects and in the practical context of problems and decision-making typically encountered in such studies. Some components are designed particuarly to improve the geostatistical instructional capability of the package. An important part of this approach involves the use of widely available software for data manipulation and evaluation in the design of a mineral inventory study progressing to mine design and feasibility. A variety of more or- less fixed routines written in high level languages provide acceptable computational speeds on a personal computer. These critical segments are linked by simple, short, compiled Basic programs easily adjustable to various data configurations and needs. IntroductionGeostatistical mineral inventory estimation has progressed greatly since its slow dissemination during the 1960s. The mining industry generally has accepted the benefits of the technique, notably the quantification of grade and geology, an indication of error in grade estimation, and of the mined volume / grade variance relationship (Clark, 1979, Isaacs and Srivastava, 1989).Acceptance has been slowed, first by complexities of geostatistical theory and second by a bewildering variety of computer systems and applications programs. Continuing improvements in education will facilitate a better understanding of the underlying theory.The purpose of this paper is to describe, in a practical context, the development of a geostatistical-based approach to reserve/resource estimation. The approach integrates various existing commercial software packages with a wide selection of programs developed by the authors for personal computers which estimate mineral inventories and educate users in the techniques applied; that is, the QMIN system.It is hoped that the approach presented here will convince mining and geological engineers concerned with resource estimation, of the soundness of geostatistical methods and its broad potential to their problems."

Jan 1, 1992