Search Documents

By Samer R. Rabab?ah

As part of the PHX Sky TrainTM project at Phoenix Sky Harbor International Airport in Phoenix, Arizona, the existing traffic lanes at the 44th Street underpass below the Union Pacific Railroad (UPRR) Bridge will be shifted to accommodate the people mover guideway. The proposed reconfiguration and reconstruction of 44th Street required the utilization of micropiles and permeation grouting to resist the lateral forces induced by cutting into the slope below the existing bridge abutment footing. This paper discusses the evaluation of the existing bridge abutment, including analysis of the original foundation system, and design, installation and testing of a new micropile-supported retaining wall to support the cut slope below the existing bridge abutment foundation. A monitoring program was implemented during construction to evaluate the short- and long-term performance of the bridge abutment. Instrumentation included survey monitoring points, inclinometers, tiltmeters and crack gauges. A micropile load testing program was conducted to verify design assumptions concerning micropile axial and lateral loading. Numerical analyses (using PLAXIS software) were performed to predict the short- and long-term behavior of both the abutment wall and the bridge foundations. Movement data collected from the monitoring program indicate that the wall and bridge foundations are performing satisfactorily and within the general bounds of predicted movements. The results from the numerical modeling using PLAXIS software showed that the proposed solution is deemed adequate to provide the needed global stability with an acceptable factor of safety, along with acceptable deformation.

Jan 1, 2011

By F. D. Rosi, C. H. Mathews

THE plastic properties of face-centered cubic metals below room temperature present a field of investigation which has not been extensively ex-plored. The work by Schmid and Boas1 has demonstrated the importance of temperature upon such properties as strain hardening and critical resolved shear stress. The work by Yamaguchi2 upon the shear stress as related to the number of slip bands accentuates the necessity for further experiments of a similar nature. The approach to a mechanical equation of state from the standpoint of thermal fluctuations and activation energies by Becker3 and more recently by Kauzmann4 further emphasizes the need for a quantitative and more comprehensive analysis of the dependence of fundamental plastic properties on temperature. The purpose of the present work was to investigate specifically: (1) The gross shape of the stress-strain curves at several temperatures, (2) the change in the critical shear stress as a function of temperature, and (3) the number and appearance of slip bands as a function of strain and temperature. Preparation of Specimens Single-crystal specimens of 99.996+ pct alumi-num, 1/2 in. in diam and 5 to 6 in. in length, were made by the Bridgman method of gradual solidification from the liquid state. The crystallographic orientation of the single crystals was determined from back-reflection, Laue X-ray photograms ac-cording to the method described by Greninger.6 In most specimens the Laue photograms showed double diffraction spots indicative of the lineage structure type of imperfection, discussed in great detail by Buerger.7 The angular spread of these spots was never observed to exceed 2". Most of the crystals were radiographed to insure against microporosity. In preparing the metal surface for optical microscopy, the following sequence of operations gave good results: The as-cast crystals were turned down in a lathe, 0.001 in. per cut, to obtain a 2.5 in. gauge length. The cold-worked layer resulting from this operation was removed chemically by etching with Tucker's reagent. Then the specimen was polished mechanically through 2/0 metallographic emery paper, after which it was etched again to remove the cold-worked layer resulting from the mechanical treatment. A 48-hr anneal at 580°C ±10°C followed so as to insure an essentially stress-free single crystal. After the annealing treatment, the specimen was electrolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. With a current density of 10 amp per sq dm (decimeter) the time required to obtain a satisfactory surface varied from 10 to 12 min. The polish-ing was carried out for short periods of 2 min to avoid rapid deterioration of the solution as well as to enable the rotation of the specimen 180" for uniformity of polish. It was necessary to place the solution in a bath of dry ice in view of its explosive nature at room temperature. Etching of the electrolytically polished surface was accomplished by using the fuming etch-pit method recommended by Lacombe and Beaujard8 for high-purity aluminum. Method for Tensile Testing A modification of the loading equipment devised by Miller9 was used. In this apparatus, the specimen was suspended from a chain and gimbal arrangement (for axial loading) in a heavy steel framework connected at the bottom to a balanced 6:1 lever and bucket system. Loading of the specimen was accomplished by allowing sand to flow from a reservoir into the bucket suspended from the longer end of the lever-arm at a rate of approximately 3 lb per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire, strain gauge and an SR-4 portable strain indicator (type K), which permits a reading accuracy of 2 microinches per inch. For low-temperature study, the gauge was calibrated by measuring the elastic modulus of an annealed stainless steel rod, which is known to be independent of temperature."

Jan 1, 1951

By E. J. Bruderlin

A METALLURGICAL process to be economically successful must be carried on under proper conditions of control and equipment. The question of equipment is always of primary importance. In the dis-tillation process for the recovery of zinc by retorting, the retort is the all-important piece of equipment. Each retort in a working block must function as a separate unit. Over-all block efficiency is the result of the ability of the individual retort -to withstand the severe conditions of operation for a maximum period of time. Therefore retort manufacture has been an ever present problem with the operator of a zinc-retort-ing plant. During recent years the zinc-plant operator has been faced with rapid changes in the character of the ores and concentrates. Operating costs have increased as a result of the- introduction of the flotation process and the amount of flotation concentrates to be handled. To counteract increasing costs, the operator has found it necessary continually to attempt heavier loading of retorts, until a 45 to 50-lb. charge per cubic foot of retort space has become common practice. Heavy loading has brought about severe firing conditions, which, in turn, have emphasized the necessity for further improving the quality of the retort. Increasing percentages of detrimental impurities in the retort charges have also added to the operator's difficulties.

Jan 1, 1936

By C. Liley

Open cut blasting at the Ernest Henry mine has the potential to cause damage to nearby underground workings. This paper is a case study of the blast vibration management project which was conducted to ensure pit blasting did not adversely affect the stability of upper production levels or cause damage to the underground primary fan units.

Jan 1, 2012

By A. J. Abraham, K. E. Seitz, J. D. Humphrey

Caterpillar has led the way for sound reduction in off highway trucks (OHT) used for mining. In 2000 Caterpillar introduced the 793CXQ sound reduction OHT (Figure 4) to meet local noise level demands in the Hunter Valley near Sydney, Australia. The sound level of the mining equipment in the Hunter Valley is being reduced to pre-serve the quality of life for the residents of the area. To meet the levels established required a major redesign of the 793C, as a result the sound power level was reduced by 9 dB (A), which is a less than 1/8the original sound level.

Jan 1, 2004

By James Gayley

(Wilkes-Barre Meeting, June, 1911.) THE paper presented to the Institute in 1910, by H. 0. Hofman, on Recent Progress in Blast Roasting,1 has called the attention of the iron industry to the adaptability of these processes to the reclamation of by-products such as flue-dust and blue billy, and the better preparation of concentrates and fine ores for use in blast-furnaces. The waste of valuable iron-ore through the production of flue-dust has increased at an enormous rate, and much of it has in reality been wasted as far as future recovery is concerned. Only in recent years has a possible future value been recognized, and the material stored. The increased use of Mesabi ores, which carry considerable fine ore, is principally responsible for the great increase in the production of flue-dust. The amount of fine material that is carried over depends on the fineness of the material and the velocity of the gases, and also to a very great extent on the regularity or irregularity of the working of the furnace. Attempts to recover a part of this loss have been made by recharging a portion of the production into the furnace, but as this material has been once carried out from the furnace, it is naturally in good shape to be carried out again. A recent practice at some works, is to soak the flue-dust thoroughly with water to give it more cohesiveness, but by many this is considered of doubtful advantage in the furnace, and the gases are in consequence heavily laden with moisture. There are vast deposits of magnetic iron-ores in the United States and Canada that are too low in iron for use at the present time, but which can be economically concentrated into very rich material ; in many cases the fineness of crushing necessary to secure proper concentration has prevented their

Aug 1, 1911

By Jinung Do, Sung-Ryul Kim, Juhyung Lee

"Model tests have been performed to investigate the vertical, horizontal and cone tip resistances of bucket pile embedded in sand by different installation methods; suction force by pump and jacking force by actuator. Micro-cone penetrometer is used to evaluate the variation of the effective stress inside and outside of the pile after installation. As a result of vertical pull-out test, the jacked pile shows 3 times larger resistance than the suction-installed pile. For horizontal pull-out test, the ultimate horizontal capacity and the slope of load-displacement curve on the suction-installed pile decreases by 22% and 40%, respectively, compared to the jacked pile. In cone penetration test, inside cone tip resistance of the suction-installed pile is about 40% smaller than the jacked pile, which indicates that the effective stress is reduced due to upward seepage of bucket pile in sand by suction force. Therefore, installation methods can affect the behavior of the bucket pile significantly.INTRODUCTIONA suction force occurred when bucket pile penetrates into sandy soils induces seepage flow into the bucket pile so downward seepage near the outside of bucket pile causes to increases the effective stress, while upward seepage inside the bucket pile decreases the effective stress (Mahn, 2005; Fig. 1). The effect of induced seepage causes to reduce the penetration resistance during installation. On the other hand, reduced effective stress can decrease the horizontal and vertical capacities of bucket pile by significant disturbance at the tip of the bucket pile due to the flow net. Due to the complexity and difficulty considering the effects of suction installation, many previous researchers generally have neglected the effect of suction installation in their experiments. Therefore in this study, the effects of suction installation on resistance of bucket pile is examined."

Jan 1, 2016

By Scott A. Walker, Gabriel J. Alcantar, Brian Zuckerman, Ramin Golesorkhi

"The new San Francisco 49ers Levi’s Stadium is part of the next generation of sporting facilities. Constructed in Santa Clara, Calif., the new structure has 68,500 open-air bowl seats and includes a 7- story tower housing more than 150 suites. The overall project includes the stadium structure, elevated open pedestrian walkways, commercial community space, three new pedestrian bridges and improvements to the adjacent light rail station. Sustainable design for the project includes a green roof, photovoltaic panel and a ground source geothermal system. Stadium-wide next-generation Wi-Fi capability is another feature. The design-build project team included HNTB (project architect), Magnusson Klemencic Associates (MKA, structural designer) and a joint venture of Turner Construction and Devcon Construction (TDJV, general contractor).During preconstruction, the 49ers’ original design team and the design-build team formed later worked together to facilitate communication and provide continuity. This helped to meet the project’s aggressive schedule. Working directly for the 49ers, with the design-build team, Treadwell & Rollo (T&R) served as the geotechnical engineer of record for the project from preliminary to final design and through construction. Although not contracted directly to TDJV, the stadium ownership encouraged direct interaction between T&R and TDJV and improved responsiveness to geotechnical issues during design and construction.Subsurface ConditionsThe new stadium lies within the Santa Clara Valley, a deep alluviumfilled basin resulting from historic movement on the active and potentially active strike-slip and thrust faults that bind the valley. The valley is filled with Holocene age (approximately 11,000 years old to present) alluvium, consisting of levee and basin deposits, with bedrock more than 750 ft (229 m) beneath existing ground surface. The stadium site is between two of the highly-active faults in California, the Hayward Fault 6.8 mi (11 km) northeast, and the San Andreas Fault about 11.8 mi (19 km) southwest."

Jan 1, 2014

By T J. Beardsmore, N Wyche, D Flint, T J. Griffin

Western Australia (WA) is currently the world’s largest iron ore producer, and mining of its huge reserves and resources of iron ore has become a critical part of the state’s economy and regional development. Iron ore exports from WA have reached 760 Mt/a, corresponding to shipping more than one Mt per turn-of-the-tide from the state’s ports. The iron ore sector dominates all commodities produced in WA, and in 2016 accounted for 77 per cent of the state’s royalty receipts, 56 per cent of mineral and petroleum exports (by value) and 50 per cent of mining industry employment. Expenditure on exploration for iron ore (including that for resource estimation and conversion to ore reserves) has declined markedly, from its record peak of $1100 M in 2012 to $280 M in 2016, placing it second after gold. Foreign investment has been a key element underpinning development of the iron ore industry from the 1960s until today, and will likely continue to be so into the future.CITATION:Flint, D, Wyche, N, Beardsmore, T J and Griffin, T J, 2017. The importance of iron ore to Western Australia’s economy, in Proceedings Iron Ore 2017, pp 7–12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By N. Melnyk

IN the past, the Cadomin Coal Company has opened four mines, all in the same coal seam or its folds. Three of these were opened from river level by horizontal entries or rock tunnels, and the fourth, the present working mine, by vertical shafts. This paper deals largely with some operating phases of this fourth mine, with which the writer has been associated. The seam worked here is a thick, steep, bituminous seam, and the writer feels there is a paucity of published data on the mining of such seams. Possible reasons for this are that such seams do not !end themselves to intensive development or mining, there is little chance to mechanize because of the extreme pitch, and operations are fraught with many problems. In addition, the present operations in this particular seam are being carried on at a level below the former workings, introducing new problems, not en-countered on the upper level. Coal will, without question, long continue to be an important factor in the national economy, and some of the best coal is to be found in thick, steep seams. But with the exhaustion of the easily-mined coal near the outcrops, future coal will have to come more and more from lower levels. At Cadomin there is still considerable coal on the second level, below the old river-workings, and there is a possibility that, in the future, still lower levels will be worked. It is the purpose of this paper to indicate some phases of such lower-level operations and to invite discussion.

Jan 1, 1942

By M. Rudolph, A. van Hall, G. Öktem, S. G. Özkan, A. Hassanzadeh

Despite the four-decade study on ultrasound’s (US) impact on mineral’s floatabilities, there is still not clarity regarding its role in mineral surface wettability. For this purpose, the present investigation endeavours ……the hydrophobicity and floatability characteristics of a chalcopyrite-pyrite-quartz (Cp- Py-Qtz) system in the presence and absence of an ultrasonic pre-treatment. The ultrasonic process was carried out by a sonopuls at a constant frequency of 20 kHz with an adjustable power level from 30 to 200 W. Initially, the impact of sonication time (15, 30, 45, 60 and 90 s as well as 10, 20 and 30 min) and power magnitude (30, 60, 90, 120 and 180 W) were evaluated while the dissolved oxygen, temperature, conductivity and pH were also monitored. Collector-less micro-flotation tests were carried out on the non-pre-treated and the US pre-treated samples at 60 W and 15 s. The samples’ hydrophobicities were determined by the drop shape analysis approach. The dissolved-oxygen level was varied using a mini bench pressurised water reactor to study the effect of O2(aq) concentration on the chalcopyrite and pyrite wettability characteristics. The results showed that the minerals’ hydrophilicities were relatively more sensitive to the sonication’s time than its power that resulted in reducing all three minerals’ hydrophobicities. In addition, it was found that the dissolved-oxygen content and creation of sub-micron sized bubbles led to an improvement on chalcopyrite and pyrite hydrophobicities. Finally, we proved that the Cp’s floatability increased and Qtz’s recovery reduced while being subjected to the ultrasonic irradiation (15 s at 60 W); however, Py’s recovery remained constant. This conclusion confirmed the possibility of a selective separation in ultrasound-assisted copper ore flotation. We recommend that further advanced investigations be conducted, using an X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) to thoroughly understand the surface modifications induced by the ultrasonication

Jan 1, 2020

By Hidenori Okamoto, Katuto Itoh

"Nippon Mining & Metals' Hitachi Refinery refines 40% of the anodes produced at its Saganoseki Smelter & Refinery. Its current annual production stands at 180,000tons.The refinery always endeavors to increase productivity. One of the outcomes of its efforts is an originally developed automatic short-circuit detector used to inspect short-circuits between anode and cathode. The detector is designed to inspect the 56 pairs of anode and cathode in a cell by fluxgate sensors at once. It inspects 564 cells, automatically and un-manned, and gathers data to be put into a computer. The development of the detector led to a reduction of man-power and achieved a detection accuracy superior to that of a hand-held gauss-meter. In addition, statistical and historical processing of the data enabled early detection and early recovery of the cells with poor efficiency.The new system also contributed to raising the refining capacity and reducing the unit steam consumption, because it is possible to inspect even the cells covered with thermal insulation sheets.IntroductionInspection of cells is an important component of the operation management of a tank-house. At the Hitachi Plant, it used to be carried out by two workers who walked on and checked all the cells of its tank-house once a day to find out any short-circuits in the cells, using hand-held gauss-meters. They inspected about 33 thousand pairs of cathodes and anodes a day and removed nodules by hammers. This method had following problems:it needed much manpower.the walk on the cells sometimes deranged electrodes positions.there was radiation-loss connected with the inspection due tothe fact that the workers were obliged to uncover thermal insulation sheets on the cells while inspecting."

Jan 1, 2000

By Nikhil Dhawan, Veeranjaneyulu Rayapudi

This study investigates upgrading of low-grade banded hematite quartzite iron ore (Fe ~31%). Conventional beneficiation was found to be futile. The susceptibility of iron phases to microwave exposure and their selective absorption assists in the liberation of iron values. Microwave exposure of coarse particles at 540 W for 10 min yielded a concentrate with Fe 56.30% and recovery of 50.68%. Conventional carbothermic reduction at 500 °C, 60 min and 9% charcoal yielded a concentrate with Fe 57.6% and iron recovery of 68%. The presence of sufficiently bonded silica leads to an easy formation of a fayalite phase. The microwave reduction design yielded FeG of 57.6%, FeR of 47% and a yield of 24% at an optimal condition of 540 W, 8 min and 6% charcoal. It was found that a small fraction of microwave-irradiated ore-charcoal mixture melted rapidly, and pure ferrite balls were observed within 8 min. An optical micrograph of a ferrite ball reveals the retained austenite and martensite phase.

By B. K. Parekh

Silicon carbide (SiC) can be produced by heating rice hulls to elevated temperature, The product is a mixture of beta crystalline silicon carbide whiskers, particles and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 micron in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean high grade Sic whiskers product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90 percent. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1985

By Donna L. Boreck

In an effort to increase recovery in thick and closely spaced coal seams, the Bureau of Hines, U.S. Department of the Interior, is studying the feasibility of introducing three mining methods-high-face longwall, multi-slice longwall, and longwall caving-in western coal operations. Geology plays a significant role in determining the success of such methods. Some of the factors that will affect development are as follows: (1) thickness and three-dimensional configuration of the seam, (2) cleats, joints, and fractures in the coal and roof rock, (3) roof composition and variability, and (4) coal quality and changes in quality within the seam. Through geologic mapping, the presence of many of these factors is predictable prior to development.

Jan 1, 1987

By Terrence R. Udland, Russell D. Call

"Honored with a DFI 2006 Special Recognition Award, the Four Bears Bridge was constructed across Lake Sakakawea and opened to traffi c in September 2005. The very large lake size and severe winter conditions required an effi cient foundation design capable of resisting extreme ice loading and able to be effi ciently constructed in waters up to 90' deep (27.4m).DESIGNING FOR EFFICIENCYLocated in a remote area of North Dakota, the Four Bears Bridge replacement was a major undertaking for the North Dakota Department of Transportation, with dual goals of providing a new structure that would endure a severe environment, while enhancing the natural beauty of the area. Competing bids would achieve the best price for the owner, challenging the design team to creatively solve the engineering challenges unique to the site. Foundations for North Dakota’s new Four Bears Bridge had to accommodate water level fl uctuations of up to 40 feet (12m), along with extreme ice loading and be effi cient in order to be the low cost solution at the time of bidding. All three major criteria were achieved through the use of an effi cient ‘fl oating’ lost precast concrete cofferdam founded on steel pipe piles, which allowed the contractor to achieve the project schedule. The result is an award-winning bridge that is contextually sensitive to the environment. The bridge aesthetics pay tribute to the Three Affi liated Tribes, the Mandan, Arikara and Hidatsa, who reside on the Fort Berthold Indian Reservation, adjacent to the bridge site.The original Four Bears Bridge was located over the Missouri River near Elbowoods, the native grounds of the Three Affi liated Tribes. Construction of the Garrison Dam in the early 1950’s created Lake Sakakawea, a fl ood control project on the Missouri River, and resulted in the area being fl ooded. The bridge, along with many tribal members, was relocated to a site near New Town. The bridge provides the primary crossing of Lake Sakakawea and is a critically important transportation element for the residents of the Fort Berthold Indian Reservation. The relocated bridge had become functionally obsolete and not replacing it would require a detour of 170 miles (274km). The North Dakota Department of Transportation determined that it should be replaced. In order to achieve the most effective solution, the North Dakota Department of Transportation selected a design team responsible for the creation of competing steel and concrete designs that were competitively bid. The design team was led by Kadrmas Lee & Jackson, with FIGG responsible for the concrete bridge design, while Lichtenstein Consulting and Kadrmas Lee & Jackson completed the alternate steel bridge design."

Jan 1, 2007

By Parry. V. F., John B. Goodman

"INTRODUCTION The Denver region coal field, covering an area of approximately 7,640 square miles, extends from the Wyoming State line to the middle of El Paso County, Colo. The coal in this region is subbituminous in rank. Much of it is used as domestic fuel. During the last decade the production of coal in this field has remained fairly constant at an average of 2,600,000 tons per year. This production has come from 50 to 60 mines, 88 to 90 percent of the production being from the section of the field north of Denver.According to the Standard Specifications for Classification of Coal by Bank of the American Society for Testing Materials 4/ the coals in this region are classified in the Subbituminous B and C group. On the as—mined basis, they contain about 22 percent moisture and average 9,600 B.t.u. per pound. They are noncoking and slack to a variable extent when exposed to the weather. This is characteristic of subbituminous coals."

Aug 1, 1939

By Bülent Erdem, Zekeriya Duran, Tuğba Doğan

The objective of this study was to evaluate the potential health risk associated with exposure of dozer operators to whole-body vibration. Measurements were made on 31 dozers used in different surface mines in Turkey. Predictions of adverse health effects of vibration were based on the standards BS 6841:1987, ISO 2631–1:1997, ISO 2631–5:2004, and the EU Vibration Directive:2002. Operators experienced high and comparable levels of vibration acceleration and dose during all dozer tasks: pushing the material (DOZE), moving forward (FORWARD), moving backward (REVERSE), and ripping (RIP). Specifically, DOZE, FORWARD, REVERSE, and RIP showed high potential of adverse health effects in terms of vibration dose according to the worst-case axis and vector sum criteria and a moderate adverse health effect for acceleration according to the worst-case axis criterion. Operators of large dozers were exposed to lower levels of vibration. However, no statistically significant relationship between vibration exposure levels and the propelling mechanism and the service time of dozers, operator experience, operator age, and ground type was found.

Jun 16, 2022

By Jhon Silva-Castro, Russell Lamont

Understanding the behavior of materials subjected to high strain rate conditions is of fundamental importance to the mining industry. Several stages of the mining process involve high speed loading rates including blasting, scraping, comminution, etc. Technical comprehension of how rocks deform, fracture, and fail under these loads is a fundamental first step required prior to any serious attempts at optimization of the energy utilized for pertinent activities in the mining process. A Split-Hopkinson Pressure Bar (SHPB) was designed and constructed at the University of Kentucky to study the dynamic properties of various types of rocks.

Jan 1, 2017

By Barry L. Warner

This program involves the evaluation of means for suppressing fires on underground coal mine conveyor belts. Full scale conveyor belt fire tests were conducted to determine the requirements of automatically actuated water sprinkler, high expansion foam, and multi-purpose dry powder extinguishing systems, and of various fire detection devices, necessary to adequately protect underground belt heads. The program included the development of a suitable MI scale conveyor belt test fire, conducting of fire tests in which extinguishing and detection systems and equipment were evaluated, and testing to evaluate the effects of the coal mine environment on detection equipment. Preliminary testing conducted to develop a suitable test fire revealed that fire can propagate on some conveyor belting classified as fire-resistant. New fire-resistant PVC and new non-fire resistant rubber belts were used in the full scale fire tests. These tests indicated that a single branch line sprinkler system with relatively low water pressure provides adequate belt head protection. High expansion foam and multi-"purpose dry powder extinguishing systems as presently specified by regulation were found to be suitable for belt head protection, although care is required with powder systems to assure adequate distribution. Thermal type detection devices were found to be most practical for conveyor belt protection, with combustion products and optical detection methods having serious disadvantages.

Jan 1, 1974