Search Documents

By Allen J. Johnson

Anthracite coals have been divided into three groups: (I) meta-anthracite, a high-carbon coal that is usually very slow to kindle and difficult to burn, at least on conventional equipment; (2) anthracite, a high-carbon low-volatile coal of widely accepted value as both a domestic and industrial fuel; and (3) semianthracite, a coal lying between anthracite and bituminous coal in carbon and volatile content, and also, generally speaking, in burning characteristics. Anthracite Groupings The technical differentiation between these groups, as defined by the A.S.A.-A.S.T.M. Sectional Committee on the Classification of Coals, is as shown in Table I. Tables 2 and 3 show typical analyses of anthracites and semianthracites and Figs. I to 3 show graphically the range of analytical samples. Table 4 shows the commercial sizes of coals. Meta-anthracite and Graphitic Anthracite Typical analyses from virtually every field in the United States indicate that there are few if any extensive deposits of meta-anthracite. Some of the anthracites of Rhode Island contain almost negligible quantities of volatile and would thus fall into the meta-anthracite grouping on a basis of analyses alone. However, their other characteristics indicate that it is doubtful whether they should be considered as fuels at all, but rather as graphite. In fact, this material is being mined for use as foundry facings and furnace linings.4 A typical analysis of Fenners Lodge graphite,4 from Rhode Island, is: graphitic carbon, 55.9 per cent; silica (ash), 40.6; sulphur, 1.6; moisture, 1.9; volatile, o. Other Rhode Island coals possess percentages of volatile that would throw them into the normal anthracite rather than the meta-anthracite class. However, this "volatile" is nearly all noncombustible,3,4 being composed almost entirely of carbon dioxide and inert gases, therefore its definition as volatile is open to discussion, leaving the exact classification of the fuel a moot question. One factor is certain, Rhode Island coal is so different from nor-mal anthracite in both analysis and burning characteristics that it should have a

Jan 1, 1944

By B. M. Thethwayo

Graphite blocks are currently used in the concentrate - slag zone in primary PGM smelters, and can possibly be extended to the matte zone. This project evaluates the interaction between synthetic matte and graphite blocks on a laboratory scale. Static crucible tests were performed where graphite crucibles (prepared from standard and high-grade graphite) were filled with synthetic matte (27.7 per cent S ? 46.1 per cent Fe ? 17.0 per cent Ni ? 9.2 per cent Cu) and heated to 1550°C for different time periods (1?5 days). Matte penetration was evaluated using a SEM, while graphite dissolution was evaluated by measuring the carbon content of the matte with a LECO carbon analyser. Matte penetrated into standard grade graphite up to approximately 2 mm, while matte infiltration into the high grade graphite was limited to the immediate hot face. The saturation solubility of graphite in the synthetic matte at 1550°C was 0.43 per cent. Copper, iron, nickel, and sulphur were detected in an accretion that formed in the water-cooled part of the furnace. This accretion consists of mainly Cu-S and Cu-Fe-S based phases.

Jan 1, 2012

By Gianni O. Chieruzzi

A 400 MW, gas-fed power plant on floating piles and piled raft foundations was constructed in the Province of Moskovskaya, Russia in 2008. The subsurface is characterized by fill underlain by loose to medium dense alluvial deposits, with peat and clay interbeds, a stiff to hard, highly plastic, silty clay stratum of glacial origin, and a stratum of very dense, varved interbeds of sand and silt. More than 800, drilled concrete piles were constructed at the site. The pile length ranged from 15 to 23 meters below existing surface grade, and the pile diameter ranged from 0.9 to 1 meter. Initial analyses by others predicted total power plant settlements of 3 to 4 cm when subjected to the permanent loading conditions. Under a peer review process for the equipment supplier, subsurface investigation and testing were performed to verify the consolidation parameters used for foundation design of the power plant foundation. The parameters obtained in this investigation were used in the 3-D finite-element model ELPLA as inputs for the settlement analysis of the turbine building and power island. The ELPA analyses predicted settlements on the order of 7 cm over a period of 30 years. The actual settlements after two years of monitoring were compared against the model predictions. The rate of settlement and the recompression index were both underestimated in our model. The measured settlements have enabled us to calibrate both of these model parameters so that the model better matches the data.

By P. R. Brito-Parada, A. Norori-McCormac

Positron emission particle tracking (PEPT) has become an important tool for flotation research, as it is able to resolve directly the behaviour of particles in laboratory scale flotation vessels. The first applications of PEPT to flotation showed only the motion of an individual particle in the pulp and the froth, but nonetheless allowed interpretations of behaviour not previously possible. Since then, PEPT measurement and data analysis techniques have improved significantly and now ensure a high level of confidence in the particle behaviour obtained. In particular, statistical analysis of long-duration experiments allows time-averaged data to be collated, ensuring spatial accuracy and allowing rigorous comparison of different conditions. It will be shown that these PEPT techniques can be used to compare directly the effect of operating conditions and particle properties in a laboratory flotation system. Particle tracks will be illustrated, as well as analyses of particle speeds, average flow streamlines and occupancy that show marked differences in behaviour near the interface and impeller.

Jan 1, 2015

By Ross I. Kelly

Carbonate rocks are widespread throughout Ontario and provide raw material for more uses than perhaps any other rock type. The principal carbonate rocks that are used by industry in Ontario are Paleozoic era limestone and dolostone. Limestone is a sedimentary rock that is composed mainly of the mineral calcite (CaCO,) while dolostone, also a sedimentary rock, is composed mostly of dolomite [CaMg (CO,),l. The majority of the province's limestone and dolostone extraction occurs from Paleozoic era rocks located in southern Ontario. Calcite and dolomite are also found in Precambrian marbles, calcite veins and carbonatites, however, utilization of these rocks by industry has been less common. Calcite and dolomite-rich rocks are utilized for a wide variety of uses including raw materials for cement and lime manufacture, chemical and metallurgical stone, fillers and construction aggregates (Derry, Michener, Booth and Wahl and OGS 1989a). For some uses chemical and physical requirements are very important. In the manufacture of glass, for instance, the chemical requirements of source materials are very important and very stringent. In other uses physical criteria such as whiteness may be more important. Although carbonate rocks are quite plentiful within the province, deposits that contain high concentrations of calcite or dolomite are somewhat limited. For that reason, this paper focuses on deposits that are known to, or may contain, a high percentage of calcite and/or dolomite. The paper emphasizes potential sedimentary limestone and dolostone resources, as these are the carbonate rocks most commonly utilized by industry in Ontario.

Jan 1, 2001

By A. Tabereaux

The reduction of perfluorocarbon (PFC) emissions from aluminum electrolytic cells is a key issue in reducing greenhouse gases at all aluminum smelters, The emission of tetrafluoromethane (CF4) and hexafluoroethane (C2F6) gases during anode effects at smelters can be calculated using two different methods; anode effect-minutes slope and anode effect overvoltage, This work demonstrates that the optimum method depends to a large extent on the type of anode effect kill algorithm utilized at each smelter, CF4 emissions vary widely from aluminum cells depending on the type of anode effect kill method utilized; fast, aggressive anode bridge movements vs. slower, moderate anode bridge movements.

Jan 1, 2005

By W. Ferreira

Steel is produced in a basic oxygen furnace from hot metal obtained from a blast furnace. A sintered iron ore with good hightemperature properties (strength and permeability) should be used as feed to the blast furnace. The quality of this sintered ore depends on the reactivity of the iron ore used as feed to the sinter plant during the lime assimilation step in the sintering process. The penetration test is the standard method for evaluating the reactivity of iron ore with lime. It is, however, difficult to determine the exact depth of penetration from the standard test. A new test method is proposed that allows automatic evaluation of iron ores in terms of lime assimilation with increasing temperature. A comparison of the coefficients of variation for the new and standard methods for each ore type demonstrates that the results of the new test are more reproducible and more precise than those of the standard method. The test is also less time-consuming and easier to implement.

Jan 1, 2014

By Thomas D. Henderson, Wayne R. Hopkins, Arthur Lynch

Brought on stream in 1975, the 10,000-tpd copper oxide processing plant of Anamax Mining Co. at Twin Buttes, Ariz., is now at design capacity. Based on acid agitation leaching, solvent ion exchange, and electrowinning, the Anamax plant bridges an ore to metal gap by producing mine site copper cathodes from lime-bearing oxidized feed. Until recently, such material was considered submarginal because copper recovery was uneconomic using conventional methods. The new Twin Buttes oxide plant, the largest of its kind in North America, is one stage in the expansion of Anamax, a joint venture owned equally by The Anaconda Co. and Amax Inc. Other phases include an accelerated stripping program in the pit, an expansion of the sulfide concentrator from 32,000 to 40,000 tpd, and construction of a 57 MW diesel generating station for the oxide plant. Once the basic oxide flowsheet had been selected, Anamax awarded a contract to a joint venture of Arthur G. McKee and Co.' (Western Knapp Engineering Div.) and Davy Powergas' (a member of the Davy International group). The contract covered process design, engi¬neering, procurement, and construction. The property, identified by Banner Mining Co. in the 1950s and developed by Anaconda, was put into production in 1965 as an open pit mine equipped with a 32,000-tpd sulfide flotation concentrator. The Twin Buttes mine has since become one of the largest earth¬moving operations in the world, excavating some 10 tons of waste per ton of ore. At the original sulfide mill feed rate, the mining fleet moved 375,000 tpd of material (225,000 tpd alluvium and 150,000 tpd of rock). The most significant copper mineral in the ore body is chalcopyrite, which is scattered in pockets of weak mineralization. Cap oxidation has progressed to depths of several hundred feet, principally as chryso¬colla. Present estimates place minable reserves at 347 million tons of sulfide ore grading 0.6% copper and 55 million tons of oxide ore grading 0.9% recoverable copper from 1.25% total copper. The nonre¬coverable fraction is composed of native copper and insoluble copper oxides and sulfides. The oxide ore has been partially stripped, and 25 million tons having a copper content greater than 0.6% have been stockpiled. The stripping of oxide ore to expose sulfides will continue for several years. The copper oxide studies launched by Banner Mining in the 1950s were continued by Anaconda. Process routes investigated included: acid leaching; cyanide leaching; segregation roasting; chlorination, oxidation, and reduction; flotation in combination with leaching; cal¬cite flotation plus leaching; copper oxide flotation; and sulfidization flotation. By late 1968 test work favored a low temperature roast followed by an ammonia-ammonium carbonate leach of the ore. During this period, acid leaching had been discounted because of excessive con¬sumption of expensive acid by the high limestone ore matrix. Restric¬tive SO2 emission controls in 1971 suggested an increase in acid production and availability at a lower cost. Research then switched to acid leaching, resulting in development of the present flowsheet. Mechanically agitated leaching in a cascaded series of tanks was selected in preference to vat leaching after piloting a stirred-tank system. Preliminary testing of vat leaching indicated that inter-vat solution clarification problems could be caused by gas evolution from leaching of high limestone ore. Lack of research time for resolution of this problem, plus success of the pilot agitation system, dictated the final flowsheet selection. In 1973 Anamax decided to proceed with agitation acid leaching to produce liquor for a solvent ion exchange (SIX) and electrowinning (EW) installation. At that time, such systems were proving their eco¬nomic viability, and they allowed direct recovery of high quality cath odes while bypassing the smelting and refining of lower grade cement copper precipitates. The Anamax oxide plant processes a grade of about 1% recovera¬ble copper from stockpiled sources and new mine production. Unit operations include size reduction, agitation leaching, countercurrent decantation washing of residue, pH adjustment of solution, clarifica¬tion, solvent ion exchange, and electrowinning of copper, with a mini¬mum of environmental impact. The feed to the primary crushers is composed of: 1) -10-in. stockpiled oxide ore, which has passed through the mine crusher and has been grade-segregated to allow blending for a consistent feed material. 2) -4-ft ROM oxide ore stockpiled in the early mining operation. 3) -10-in. ore currently being mined. Ore is delivered in 100-ton mine trucks to a dump pocket, where an apron feeder transfers the ore to an inclined 6-in. fixed grizzly. The grizzly oversize passes through a 48 x 60-in. primary jaw crusher, where it is reduced to -6 in. The fixed grizzly undersize and the crusher product are conveyed to a 4-in. vibrating grizzly. Oversize from this grizzly reports to a 7-ft Standard cone crusher, where it is reduced to -1 in. The crusher product and the vibrating grizzly undersize are conveyed to two 8 x 20-ft double-deck vibrating screens that operate in closed circuit with two 7-ft short head cone crushers. Screen undersize (-1/2 in.) is delivered to a covered conical fine ore stockpile with a designed live capacity of 15,000 st. Beneath the stockpile are ten Pioche belt feeders feeding two conveyor belts that supply the milling circuits. Each group of five feeders has two variable speed and three fixed speed drives. Grinding to 95% -48 mesh is done in two parallel lines, each consisting of an 111/1 x 18S -ft rod mill and a 12' x 30-ft ball mill in open circuit. Water is added to maintain a pulp density of 72% solids in the mills. Further water additions are made to the ball mill discharge sumps to create a 60% solids slurry for transfer to the leaching reactors. The nominal grinding rate is 440 tph solids. A splitter box on the product from the mills separates the incoming slurry into two streams, one for the leaching reactors and the other for the pH adjustment reactors. This split is determined by the lime content of the feed material and the pH of solution entering the pH adjustment reactors. Five 30-ft diam by 31-ft high mechanically agitated, rubber-lined leach tanks are arranged in cascade, with gravity transfer from one to another by enclosed launders. Concentrated sulfuric acid (93.2%) from storage is added to the pulp principally at the first leach tank, and the reacted slurry leaving the cascade after a 5-hr residence time at 50% solids is pumped to countercurrent decantation (CCD) wash thickeners.' At this point, most of the soluble copper has been leached from the ore. Up to 250 lb of sulfuric acid is consumed per ton of ore, the acid being supplied in tank cars from a nearby smelter. Leached slurry at 50% solids is washed countercurrently with return raffinate from the SIX plant in a series of four Doff-Oliver center caisson, 400-ft diam thickeners. Solids advance from thickeners No. I through No. 4 to the tailings dam. SIX raffinate advances from thickener No. 4 to thickener No. l, where a pregnant solution overflows to pH adjustment. To optimize solvent extraction, the pH of the pregnant solution from CCD thickener No. I is adjusted from 1.5 to 2.5 by adding unreacted ground slurry (split from the grinding circuit) to the preg¬nant overflow of No. I CCD thickener. The resulting slurry is retained for 45 min in three mechanically agitated leach tanks. CO, generated during leach and pH adjustment is ducted to a demister, where entrained acid droplets are removed. The cleaned CO, and the No. 4 CCD underflow are the only effluents from the plant. The underflow of No. 4 thickener mixes with tailings from the sulfide concentrator and is neutralized. Slurry exits the pH adjustment vessels at about 10% solids and

Jan 1, 1985

By Benj. Lazer

Multiple seam mining has been studied and writ- ten about extensively in the past and in the latest review of the subject in 1956 David Stemple covered it exhaustively. The present discussion has to do with only one phase of the problem-"The effects on upper seams when the lower seams have been mined first." The study presented here is based on observations made in mining operations in southern West Virginia and adjoining areas of Virginia and Kentucky during the past 43 years. These observations are largely confined to the Pocahontas coalfields of southern West Virginia which have, since 1883, produced well over one billion tons of coal from an area of about 300 sq miles and where multiple seam mining has been active, or is now active, at more than 40 operations. The observations and conclusions as to the effects on upper seams when lower seams have previously been mined are therefore related only to the local coalfields in the area of the three states named but I believe that they can be applied generally to other coalfields.

Jan 9, 1965

By Andhra Pradesh, Nagarajkumar B. V

As a part of Mumbai City Mega Drinking Water Project at Amar Mahal Tunnel-1 Ghatkopar East Mumbai, drinking water tunnels were proposed by MCGM from Amar Mahal to Trombay reservoirs, Amar Mahal to Wadala and further up to Parel. The pipeline has to be underground and laid at a depth of 5.5m. The initial proposal was to provide sheet piling to enable the safe excavation and installation of underground pipeline. However, installation of sheetpiles was practically not feasible due to the existing soil strata for driving the sheet piles. Hence, it was proposed to install micropiles instead of sheet piles. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with temporary struts for shoring protection works in this project.

Sep 1, 2022

By Henry B. Estabrooks

As was the case with many other mining companies, the management of Tennessee Copper Company' viewed with some interest reports in various trade and technical journals of the successful use of ammonium nitrate-fuel oil mixtures as an explosive in coal stripping., construction, open pit mining and finally in underground salt mines. The apparently simple transition from the "interested" stage to a point where in excess of 80% of the ex¬plosives used is ammonium nitrate may be of interest. The Tennessee Copper Company operates five mines in the "Copper Basin" of Polk County which lies on the extreme southeast corner of Tennessee. The ore is a massive sulfide principally pyrrhotite and pyrite with some tough lime silicates as gangue while the walls are greywacke interbedded with schist. Average total production is 28,000 tons per 5-day week and an average of 422 feet of development per week. Development work consists of 8'x 8?, 6?x 7?, 5'x 7? and 4'x 6? drifts driven with drifter drills using 1-5/8" carbide detachable bits and 5'x 5' raises driven with stopers using 1-5/8" bits.

Jan 1, 1962

By S. Norman Kesten

The Galena mine is located astride the Polaris fault in the Coeur d'Alene district of northern Idaho. The surface installations are about a mile up Lake Gulch, the mouth of which is about 2.4 km (1 112 miles) west of the old town of Wallace. The mine had its beginnings when the first claims were located in the early boom days of the district in the 1880s and when the first underground ore bodies were opened up in 1917. During the ensuing 14 years, ore was mined from which were recovered 5.4 Mkg (12 million lb) of lead and almost 14.2 Mg (112 million oz) of silver. Workings consisted principally of a vertical shaft from surface to the 800 level and an offset underground shaft to the 1600 level, together with extensive lateral openings. High-grade silver-copper ore was discovered near the Silver Standard fault in the Sunshine mine, a few miles to the west, on the 1700 level in 1930. By 1937, the Sunshine and adjacent mines were producing silver-copper ore on a regular basis. In 1943 additional ore of a similar type was found along the Chester fault, to the east of the principal Sunshine workings. The interest of American Smelting and Refining Co. (renamed ASARCO in 1975) was aroused and the company's geologists determined that the Galena mine, idle since 1931, provided a geological environment in which similar ore might be found. After negotiations were initiated with the owners of the property, Callahan Zinc-Lead Co., the property in question was deeded to Callahan's wholly owned subsidiary, Vulcan Silver-Lead.

Jan 1, 1990

By G. L. Neumann

In October 1949 the College Park Branch of the Mining Division instituted a survey of the New England pegmatites. Many of the New England pegmatite deposits were superficially examined, and the Bumpus quarry in Albany, Oxford County, Maine (see fig. 1), was selected for a diamond-drill exploratory-development project to supply information for developing more economical mining methods and no increasing production of beryl and other scarce minerals associated with pegmatitic intrusives. The Bumpus quarry has been mined intermittently by three operators since it was opened in 1927. At the time of drilling, the vein or dike (see figs. 2 and 3) had been mined to a depth of 60 feet for a strike length of 280 feet. The dike averages 40 feet in thickness and dips 50 degrees southeast. The Bureau of Mines drilled seven diamond-drill holes between September 27 and November 27, 1950. These holes showed that the dike persists for at least 350 feet to the east and probably 200 foot to the west of the present excavation. The drilling also indicated that the dip, as exposed at the surface, continued unchanged at 500 to a depth of at least 50 foot below the pit. The dike was not delineated, although it fingered out as pegmatite interbanded with Granite, diorite, and gneiss in diamond-drill hole B-4, approximately 250 feet west of the pit. Further drilling will be necessary to find the extent of this pegmatite dike and to determine the safest and most economic mining system.

Jan 1, 1952

By P. Oghazi

It is possible to have traceability in the mining industry, by parameters and signatures like particle mineralogy, mineral association, texture and mineral liberation. The study is on an apatite-iron ore deposit at Malmberget, Sweden, and characterizes an ore body both mineralogically and texturally in a quantitative manner by using analytical methods like optical microscopy, microprobe (EMPA) and an automatic SEM based system, Particle Texture Analysis (PTA). The mineralogy was evaluated by PTA and characterized by modal mineralogy, mineral liberation and mineral associations. Magnetite has a simple outline and straight grain boundaries and the gangue minerals have a finer particle size with a more complicated texture. The PTA analysis also shows that apatite is associated to magnetite as mixed particles, while smaller grains of magnetite are inclusions in feldspar. Result from particle texture analysis shows that there is a connection which link to the mine-to-mill context, and it may be used to create traceability. This link is not the associations of the main ore mineral magnetite, nor the modal mineralogy. Instead, it is the mineral associations of contaminating minerals (apatite and feldspar) that appear to be most promising since they survive from mine to mill. The modal mineralogy may be used to understand how contaminated minerals break into or out of particles size fraction during grinding.

Jan 1, 2010

By Q. X. Li

The state discharge standard for arsenic-containing wastewater which is the first kind of pollution is less than 0.5 mg/L. In fact, in a certain company, the acidic arsenic-containing wastewater in non-ferrous smelting was as high as 860 mg/L, which is far beyond the state discharge standard. Obviously, the direct release of this wastewater without further treatment would result in great hazards to the ecological environment. To aim directly at the characteristics of acidic arsenic-containing wastewater, in this study, two steps of treatment including oxidation-flocculation and removal fluoride by mixing alkaline neutralization were suggested. Through analyzing various influencing factors in treatment effects, the optimum technical conditions were obtained. The sediments after treating were recyclable and the secondary pollutions can be avoided. Moreover, the results also show that, all indexes of the effluent after treating are lower than the First Grade Standard of Integrated Wastewater Discharge (GB 8978-1996). This novel method has advantages of short flow sheet, easy operation and low cost.

Jan 1, 2014

By Junji Shibata

It is important to recover and reuse the metal values contained in various industrial wastes in a viewpoint of environmental preservation. Most of industrial products are made through the processes to separate impurities in raw materials, solid and liquid wastes being necessarily discharged as industrial wastes. Chemical methods such as solvent extraction, ion exchange and membrane, and physical methods such as heavy media separation, magnetic separation and electrostatic separation are considered as the methods for separation and recovery of the metal values from the wastes. In this paper, some examples of the application of solvent extraction to the treatment of wastes are introduced. The treatment of solid wastes such as Ni-Co alloy scrap, Sm-Co alloy scrap, fly ash and flue dust, and liquid wastes such as plating solution, the rinse water, etching solution and pickling solution are accomplished using solvent extraction technique.

Jan 1, 1996

By Ashish Kumar, Khadija Said, Ulupi Mishra, Sekhar Bhattacharyya

Using battery-powered equipment in underground mining can improve safety, advance automation, and reduce greenhouse emissions. In this context, rechargeable lithium- ion batteries (LIBs) have a competitive edge due to their high Coulombic efficiency, superior energy density, and extended cycling stability. However, several conditions must be met for their safe operation. Their failure can cause thermal runaway (TR), which poses a significant safety risk in underground mines. Despite studies having investigated this phenomenon using physics-based models, limited research has used deep learning to predict its implications. This study aims to bridge this gap by characterizing LIB TR under dynamic airflow through simulations and predicting temperatures using two of the most common recurrent neural networks: long short-term memory (LSTM) and gated recurrent units (GRU).

Feb 22, 2026

By Pathik Deb Mallik, Shyamal K. Mitra, Rajiv Kishore, Shuvranshu Rout, Manos De

"This paper presents a case study on the design and construction of a deep underground pit structure constructed inside almost a century old existing plant building. The complexity and challenge for the design and construction lay in executing the work in a difficult subsoil condition especially the presence of deep mica schist. The limited space availability in the existing plant for construction work without hampering regular production in other adjoining areas of the plant made the execution more challenging. Experience with difficult subsoil and proximity to old foundations entailed a non-conventional engineering approach while ensuring complete safety in spite of maintaining the normal operation.INTRODUCTIONTata Steel Processing and Distribution Limited (TSPDL) is a subsidiary unit of Tata Steel Limited (TSL) having a CR processing facility inside the premises of Tata Steel Limited. TSPDL intended to install equipment for a new slitting line inside the existing shed including construction of very deep structure called “loop pit” where the strips from cut CR sheets collect in the form of loops and are recovered as scrap. The entire plant is located within the shed of existing plant. The construction of all foundations including the loop pit is to be executed in the limited area without disturbance to normal production work in balance areas of the plant and also maintain safety and integrity of existing structures.The existing shed is an old structure constructed approximately 80 years ago. The building column foundations are gravity type design of brick masonry supporting only the vertical load from the columns. This type of foundation designed with no eccentricity of loading provides no allowance for implementing any foundation stabilizing design. The present project required civil construction for the new equipment foundations safely within this area."

Jan 1, 2015

By C. K. Leith, W. J. NEAD

(Glen Summit Meeting, June, 1911.) . ONE Of the most significant developments in the iron industry in recent years has been the discovery and opening of enormous reserves of low-grade ore in eastern and northeastern Cuba. The two principal fields are the Mayari and the Moa, situated on Nipe bay, in the Province of Oriente. A less well-known district of the same type is that of Baracoa, at the east of the island, and another is in Camaguey province in central Cuba. In the comprehensive estimates of the iron-ore reserves of the world, published during the summer of 1910 by the International Geological Congress in Sweden,' these Cuban deposits are estimated at about 2,000,000,000 tons. Certain it is that the reserve is a large one. The Spanish-American Iron Co., the Juragua Iron Co. (Bethlehem Steel Co.), the U. S. Steel Corporation, and others have been active in this exploration.. The Spanish-American Iron Co. has established a port for the handling of these ores at Felton, has built a railway 16 miles to the ore-fields, and has opened up deposits for steam-shovel mining. Its expenditures have reached an aggregate of about $6,000,000 in preparation for the handling of these ores. Shipment of the ore to Sparrow's Point, Md., has begun and may be expected to rise to a considerable amount in the near future. The ore reaches this point at a cost per unit of iron considerably lower than Lake Superior ores, and the presence of a low percentage of nickel gives a desirable steel. It is not the purpose of this article to consider these ores from a commercial stand-point, but rather to discuss their-origin. If our conclusions are correct, they throw light on the character of the deposits which should have some commercial significance. 1 The Iron Ore Resources of the World, an inquiry made upon the initiative of the Executive Committee of the Eleventh International Geological Congress, Stockholm, vol. ii., p. 795 (1910).

Mar 1, 1911

By Barry L. Warner

This program involves testing to determine whether a fire hazard exists when the exposed wood surface area of timber in a mine passageway equals 40 percent of the surrounding strata surface, excluding the sill. Twelve full scale fire tests were conducted in a simulated mine passageways, using kerosene pan fires as the ignition source. The tests included three timber sizes, plus one test with roof lagging, two wood types, plus one test with treated timbers, and two ventilation air velocities. The results show air velocity to be an important factor in the occurrence of flame propagation, and that the 40 percent surface area ratio of wood to surrounding strata appears to b0. a valid criteria for fire safety at 150 fpm, but not at 350 fpm.

Jan 1, 1975