Search Documents

By Josh Swank

Albert Einstein once said, ?the important thing is not to stop questioning.? In the mining industry, a lack of inquisitiveness may lead to a blissful ignorance but it certainly will not increase efficiencies. While one may claim necessity is the mother of invention, questioning and analyzing how methods and systems can be improved is the catalyst to discovering necessities. Understandably, when working in the middle of Canada?s oil sands, where trucks operate around the clock every day of the year, it is nearly impossible to pull the nose from the grindstone long enough to provide thorough analysis. But, fortunately, some manufacturers/inventors have assisted by examining the process and the ensuing headaches within this application.

Jan 1, 2013

By K. Ronald Chapman, Claus Ludwig, Doug Jenevein

"In the spring of 2005 Schnabel Foundation Company completed a $15.2 million Design/Build subcontract to underpin 11 structures, and provide 202,800 square feet of earth retention for the Reno Transportation Rail Access Corridor (ReTRAC) project in Reno, Nevada. Schnabel’s work was part of a Design/Build contract to depress a railroad alignment through downtown Reno. The depressed section was 2.2 miles long, 54 ft wide, and up to 35 ft deep (3.5 km long, 16.5m wide and up to 10.7m deep). The trench structure was required to be watertight. SUBCONTRACT WORK OVERVIEWEleven buildings along the track alignment required underpinning. Three types of underpinning were used, designated Type 1, Type 2 and Type 3.At four buildings the trench retaining walls were to be located directly under the exterior footings. This alignment eliminated traditional underpinning and cut-off wall techniques that could normally be used to support structures. Type 1 underpinning was used at these buildings. This underpinning system consisted of a combination of permeation grouting, hand-dug piers, and permanent tiebacks. This underpinning system became the new watertight trench walls.Five buildings were located a few feet behind the trench walls, and their exterior walls were supported by continuous footings. Type 2 micropile/pile cap underpinning (patent pending) was used to support these buildings.The remaining two buildings were also located a few feet behind the trench walls, but they had column footings along the exterior walls. At these structures traditional micropile underpinning was provided through the existing footings. This is described as Type 3 underpinning.Temporary earth retention was required on both sides of the trench along most of the alignment. This shoring supported frontage roads, private property and surcharge from the temporary railroad shoofly running parallel to one side of the trench.SUBSURFACE CONDITIONSThe soil along the trench alignment consisted of river outwash deposits. The top 2 to 18 feet (0.6m to 5.5m) generally consisted of flood plain silt and sand deposits, or fine-grained fills. These fine-grained soils are underlain by the Tahoe Outwash Formation which consists of interbedded layers of sand; sand and gravel; and sand, gravel, cobbles and boulders. Some of these layers encountered during construction consisted of 30 to 50 percent cobbles and boulders, with some boulders up to eight feet in diameter.A major challenge to the design and construction of the trench structures and the underpinning was the ground water table which was 10 feet (3m) above subgrade in the deepest portions of the trench. Based on specification restrictions, temporary and permanent dewatering was not feasible. As a result, the selected design and construction methods had to consider three water conditions: the anticipated groundwater level during construction (CGW), the groundwater level for permanent design (DGW), and an additional special design condition with water at street grade."

Jan 1, 2006

By P. E. Nolan

The disproportionation of carbon monoxide is an important aspect of reduction processes, in the production of carbon filaments for composites, and in the removal of CO from CO,. It can also be a hindrance, causing carbon fouling of equipment and metal dusting. The reaction is thermodynamically favored at lower temperatures, but it occurs slowly. Catalysis of the reaction by transition metals has been examined. A materials science approach to the selection of a catalyst material and of optimum operating conditions is being taken in the present work. Of particular interest is characterization of a catalyst that can be repeatedly regenerated to prevent deactivation in long term use. Experimental data on a less studied catalyst, ruthenium, are reported.

Jan 1, 1992

By Jorge Castillo

This paper presents a dynamic analyses of heap leach pad stability under high phreatic levels and various levels of seismic loading. The dynamic analysis were conducted as fully non-linear two dimensional analyses with fully coupled liquefaction triggering using the Fast Lagrangian Analysis of Continua (FLAC) computer code. Also, the geotechnical parameters, appropriate earthquake record selection and modification, model calibration, numerical analyses and results are discussed.

Sep 12, 2005

The effect of composition on electrical conductivity (resistivity), viscosity and liquidus temperature of the slags encountered in electric smelting of PGM-containing suphide concentrates is reviewed along with the relationsip between slag composition, slag-matte separation and metal losses to slag. Optimization of slag composition at furnace temperature is attempted on the basis of opposite and parabolic trends of the viscosity-conductivity relationships of the slags. The importance of surface tension of slags is emphasized using available and estimated information, which are grouped into a useful correlation. These values are coupled with or incorporated into slag viscosity plots to illustrate the correlation between the two factors which influence slag-matte separation as well as refractory attack. The electrode in the slag-resistance furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power. The obvious parameters are the size and positioning in the slag bath, which are defined by slag resistivity, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles, which in turn affect flow conditions. Thus the flow of slag and matte isdiscussed in conjunction with the furnace geometry, stirring action of the electrodes, buoyancy and electromagnetic effects. The action of the electric furnace as a settler is discussed. The rectangular furnace is considered as a channel reactor in this analysis and the action of the electrodes is described to indicate a balanced settling rate in the area of electrode action. Discussion of the design and production capacity of the electric furnace with reference to operating current, power input, furnace dimensions and electrode size are based on considerations derived mainly from slag properties such as its resistivity, viscosity and liquidus temperature.

Jan 1, 2004

By C. J. Pritchard, R. D. Jacksha, K. V. Raj, C. B. Sunderman

In underground metal/nonmetal mines, repeated localized short-term exposure to high levels of airborne contaminants can become a serious health issue. Currently, there are no common mechanisms to control or mitigate these short-term high exposures to contaminants. To improve miners’ health and safety, the U.S. National Institute for Occupational Safety and Health’s Spokane Mining Research Division (SMRD) is developing a smart monitoring and control (SMAC) system for the real-time monitoring of mine air quality, with integrated countermeasures to reduce high concentrations of airborne contaminants in localized sections of mines. To develop and test a SMAC system capable of being implemented in an underground mine, SMRD researchers built a test apparatus incorporating a fan, louver, ducting and sensors combined with atmospheric monitoring and control software. This system will institute effective countermeasures to reduce contaminant levels, improving miner safety and health.

Jan 1, 2018

By M. S. Diederichs, G. Walton

"Developments in understanding the brittle fracture of rock over the past two decades ultimately led to the acceptance of a cohesion-weakening-friction-strengthening model as an appropriate strategy for the modelling of spalling using a continuum approach. This strength model has been used to replicate observed failure depths and geometries for a number of case studies in the literature, most notably the AECL Underground Research Laboratory in Manitoba. One thing which these case studies typically ignore, however, is the influence of rock dilatancy on the evolution of brittle failure. Physically, this phenomenon is the volumetric expansion of the rock due to fracture opening; numerically, this phenomenon is captured by the flow rule, which is often characterized by the dilation angle, ?. Accurately modelling rock dilatancy in conjunction with strength evolution is necessary both to predict the magnitude and distribution of ground displacements, as well as the exact depth and shape of the fracturing zone. Both of these factors can have significant implications for support design. This paper is focussed on presenting some of the recent developments in this field in the context of a number of numerical modelling case studies. Initially, a new model for the dilatancy of brittle rock is presented, as well as some representative data and model parameters for different rock types. Next, several case studies of highly stressed tunnels and shafts are presented. The results of continuum numerical models are presented to demonstrate the ability of the back analyses to match observed in-situ measurements and obtained. The predictive capabilities of the material model are also highlighted for cases where sufficient “a priori” information (such as laboratory compression testing data) are available. The issues of model nonuniqueness and strain-localization/bifurcation are also addressed."

Jan 1, 2015

By H. C. Fuller

Depletion of iron ore in the Nation's large deposits has directed attention to other sources. One of these is the titaniferous iron ore of the Iron Mountain, Wyo., area. Tests were made to determine the feasibility of smelting this ore, which contains about 20 percent titanium dioxide (Ti02), in an electric-arc furnace to produce pig iron. Initial tests, which were made in a 30-pound-capacity induction furnace, demonstrated that the iron could be easily reduced to metal and that limestone was a suitable and effective flux. Larger scale tests then were made in a 50-pound-capacity electric-arc furnace to obtain the more detailed information necessary for the planned continuous operation of a still larger arc furnace. The principal facts determined by preliminary batch-smelting studies were that (1) 9 pounds of limestone flux was required for each 100 pounds of ore smelted, (2) expensive coke was not required because coal proved to be a satisfactory reductant (near stoichiometric carbon was optimum), and (3) overreduction, which produced a viscous slag, must be avoided.

Jan 1, 1961

By Anthony P. Makuch

Dynatec Corporation is an integrated mining services company, providing mine development, operations management, engineering, drilling and metallurgical services to the North American mining industry. Dynatec was the contract operator of the Ken Snyder Mine in Midas, Nevada from start of production in January 1999 to September 2001. This paper summarizes Dynatec?s experience and approach to the use of longhole stoping methods for mining to widths of 1.3 to 2 metres in a steeply dipping narrow vein orebody.

Oct 1, 2001

By Charles Hardy

ACTIVATED alumina is an aluminous material which may be 1 classified chemically as a partially dehydrated aluminum trihydrate having a high porosity and a perma¬nent physical structure. In general, it may be employed effectively and economically for the complete removal of water vapor from gases and vapors; for the selective adsorption of certain as especially those of the higher boiling points, and as a catalyst or catalyst carrier. Other forms of alumna are available and may be employed similarly but not so effectively nor can reactivation be accomplished with uniformity over many cycles without deterioration. The adsorption-reactivation cycle of activated alumina can be repeated many times without any apparent depreciation ill

Jan 1, 1934

By W. J. Boone

Experimental determinations were made of vapor-liquid equilibria data for a helium-nitrogen-methane system. A mixture composition was chosen to approximate the crude helium to be produced Or conservation that will eventually be further refined to obtain pure helium. Although there are publications of studies of the vapor-liquid equilibria of helium-nitrogen, helium-methane, and nitrogen-methane binary systems, there is little indication of work done on the ternary system of helium-nitrogen-methane. The experimental data presented in this report supplement the information available for the binary systems. The equilibrium vapor-liquid data and equilibrium vaporization coefficients are presented in tabular form. Graphs are employed to show an extensive amount of the data.

Jan 1, 1963

By Jr. Sayre

Results of studies of reservoir and wax-precipitation temperatures relating to wax deposition in the reservoir of the Bradford oil field are presented in this report. During 1949 and 1950 Bureau of Mines engineers made temperature measurements in 42 wells, which indicate that the Bradford Third-sand temperatures range from 59.7° F., at 1,150 feet, to 71.9° F., at 2,040 feet. Reservoir temperatures measured at the same depths in newly drilled wells and oil-producing wells differed as much as 4.5u F. Injection-well temperatures measured during water injection showed that the temperature of the water entering the sand was 11.5° F. lower than reservoir temperatures before injection. The cooling in the formation resulting froth the injection of low-temperature water was 11.5° F. in the vicinity of the injection-well bore, and a maximum of 2.1° F. 200 feet from the injection well. Sand temperature, after 5 months of water injection, was reduced 1.5° F. 90 feet from water-injection wells. The temperature at which wax begins to precipitate from solution in crude oil was determined at atmospheric pressure for 26 samples and ranged from 51° to 67° F. Oil samples from wells producing no water had wax-precipitation temperatures ranging from 51° to 58° F. and wax contents from 2.20 to 2.97 weight percent, whereas the samples from wells producing water and oil had wax precipitation temperatures ranging from 580 to 67° F. and wax contents from 2.57 to 3.42 weight percent .

Jan 1, 1952

By M L, G Maddocks, A Ferrier, ers, A Forbes

Evolution’s Mount Rawdon Operation (MRO) produces gold and silver through open pit mining methods. The mining operations are scheduled to be completed in FY24 (Financial Year 2024), after which low-grade stockpiles will be processed until the end of FY27. As part of MRO’s Progressive Rehabilitation and Closure Plan (PRCP), RGS Environmental Consultants (RGS) and Deswik were engaged to develop the final landform surface and a whole of site probabilistic water balance/water quality (WB/WQ) model to evaluate the viability of several closure options with respect to water quality in the various site water storages, particularly the final void which will form a pit lake. This case study details the closure option which included (amongst other things) covering the final landforms and directing water toward or away from the final void post closure. Closure and rehabilitation for MRO had previously been planned and evaluated on a ‘domain’ basis. Furthermore, the rehabilitation plans and final water management plans for the Tailings Storage Facility (TSF), Waste Rock Storage Facility (WRSF) and other domains were not coordinated, possibly resulting in competitive rehabilitation material requirements at the commencement of closure activities. An assumption was that a legacy non-acid forming (NAF) stockpile would provide sufficient material to both supplement ex-pit material for the construction of the TSF embankment raises and to complete all closure activities, but the volumes available and the volumes required to complete the closure activities had not been quantified.

Aug 2, 2023

The surface area that mining requires is a minuscule fraction of the total land mass of the United States, according to the US Bureau of Mines' latest report "Land Utilization and Reclamation in the Mining Industry, 1930-71." During the 42-year period from 1930 to 1971, the mining industry utilized 3.65 million acres-only 0.16% of a total 2.27 billion acres of land-and reclaimed 1.46 mil- lion acres, or 40% of what it used. Which leaves, as still unreclaimed, 0.096% of the nation's total land mass.

Jan 10, 1974

By Fengyu Ren, Kunpeng Yu, Gideon Chitomb, Qiangqiang Gao, Liqiang Ma, Jiangtao Zhai, Ichhuy Ngo

The penetration of rock fragments of overlying strata causes advanced ore dilution during drawing. The results of numerical and physical experiments showed that the proposed numerical simulation was applicable and the microscopic parameters of the model were reliable. The penetration under the variables of particle diameter ratio, density ratio, overlying strata thickness, and particle morphology was clarified. The penetration was quantitatively characterized by the discharge amount and the dilution rate. The experimental results showed that the diameter ratio and density ratio had a significant influence on the penetration. On the irregular shape of particles, the penetration is weakened. The overlying strata thickness had little effect on the penetration. This study could provide a theoretical basis for the full section uniform drawing, avoiding advanced ore dilution and further optimization of recovery rate.

Nov 13, 2023

By L Smith, R Beckie

An intermediate scale (8 m + 8 m + 5 m high) constructed waste rock pile experiment was built upon a contiguous grid of 16 gravity drainage lysimeters to investigate the flow of water in unsaturated waste rock. Average net infiltration to the uncovered waste rock pile is 55 per cent of precipitation. Large rainfall events have net infiltration of 55 per cent to 85 per cent. Net infiltration estimates range from 23 to 120 per cent of precipitation between lysimeters. Small-scale lysimeters of less than 4 m2 area are shown to be poor predictors of net infiltration for uncovered waste rock. The appropriate size for lysimeters increases with increasing flow rate. The residence time distribution has an estimated median value of 3.0 to 3.9 years under average infiltration conditions. Water flows within the fine grained matrix, within larger pores (macropores), and in matrix free areas of the pile. In situ tracer concentrations vary between pore sizes, and between spatially distinct areas of the pile, indicating water geochemistry may also be variable. Water samples collected from in situ soil water samplers are dominated by the most mobile water fractions. In situ measurements of water content and matric suction are compared to the measured outflow. The data indicate the focusing of flow in spatially distinct areas can make in situ instrumentation a poor (non-conservative) predictor of volumetric water flow.

Jan 1, 2003

By L. Tafaghodi, A. Hosseinpour

"Silicon is considered as the most appropriate semiconductor material for manufacturing solar cells because of its natural abundance and being nontoxic. The transferable knowledge and technology from the electronics industry and the long history of silicon-based semiconductors are also assisting the domination of silicon as the most common semiconductor material. Developing an environmentally and economically viable process for producing solar grade silicon has been one of the main challenges in the silicon industry in the past few years. Metallurgical refining processes have received significant attention because of their high productivity and low cost. Slag refining is one of the purification methods which is based on oxidation of the impurity elements, followed by its dissolution into a slag phase. This article presents a review of various slag refining processes that have been employed for purification of silicon and silicon alloys. SiO2, CaO, CaF2, CaCl2, Al2O3, MgO and Na2O are the major components of the slags used for silicon refining. These slags can be classified into three main categories including binary, ternary and quaternary slags.INTRODUCTION Silicon can be categorized into three different grades based on its application or purity: metallurgical grade silicon (MG-Si) with purity of ~98 %, solar grade silicon (SoG-Si) with purity of ~99.99999 % and semiconductor grade silicon (SeG-Si) which has the purity of 99.9999999 % (Johnston & Barati, 2010; Krystad, Tang, & Tranell, 2012; Tang, Øvrelid, Tranell, & Tangstad, 2009). Producing SeG-Si is carried out through an energy-intensive and complicated process named Siemens. This purification process is relatively slow and involves using toxic and corrosive reagents (e.g. Trichlorosilane). At present the majority of SoG-Si is produced via Siemens or Siemens-like processes and there is very limited production via processes dedicated to SoG-Si. Because of the difference in silicon specifications required in microelectronics and photovoltaic industry, and the cost and energy associated with the Siemens process, an interest has emerged to develop technologies dedicated to producing low cost SoG-Si (Istratov et al., 2003; Johnston, Khajavi, Li, Sokhanvaran, & Barati, 2012; Mitrašinovic, D'Souza, & Utigard, 2012; Wu et al., 2012)."

Jan 1, 2017

The Newcrest Mining Limited Telfer Gold Mine consists of an underground sublevel cave (SLC) operation located 734 m directly below active open pit operations. Open pit and underground current production rates are 50 million and 5.7 million tonnes per anum (Mt/a) respectively. The SLC was initiated in late 2006 with breakthrough planned to occur on the 5484 bench of the west wall in late 2009. Risk to the south ramp was identified during this time, resulting in the construction of the north ramp. The SLC was continually tracked from initiation with a suite of monitoring systems and managed with a Major Hazard Management Plan (MHMP) and associated Trigger Action and Response Plans (TARP). At breakthrough the eastern limb of the cave was located within a 70 m horizontal distance from the south ramp. The south ramp was closed in October 2009 due to significant slope deformation, extensive cracking in the berms and batters between the ramp and breakthrough bench and a major failure 250 m to the north of the cave breakthrough. Wall response was first identified from slope deformation measurements taken by the wall monitoring radar in May 2009, at which point the SLC was 160 m from breakthrough. The impact of the SLC on the slope is a unique case with the monitoring systems in place able to provide data on the slope reaction to the SLC progression. This paper will discuss the management of the south ramp such as the early interpretation of risk associated with cave breakthrough, monitoring systems implemented to track the cave progression and wall deformation, data integration and interpretation and risk management. Following the closure of the south ramp further instrumentation programs and risk assessments were conducted to determine the risk of re-opening this haulage route. The outcomes of this program will also be presented.

Nov 25, 2010

By A. Güney

Currently, recycling technologies use relatively homogeneous plastics because hand-sorting waste feed is too expensive. Many promising technologies for separating mixed thermoplastics are being investigated, but they are still uneconomical and unreliable. Burning plastics for recycling is not used because of poisonous gases released when their burning. PET and PVC cannot be separated using conventional gravity separation techniques because their specific gravities overlap; PET density changes from 1.33 g/cc to 1.37 g/cc and PVC density is between 1.32 g/cc and 1.37 g/cc. For this reason, plastic recycling needs new techniques. Among these techniques froth flotation, also used in mineral processing, can be useful for its cost and simplicity. In this method, a plastic is selected from mixture, tried to regain its natural property, hydrophobicity. In this study the experiments were applied by using plasticizer reagents to make the selected plastics hydrophobic and us-ing NaOH to render the other hydrophilic. Post-consumed PET and PVC are evaluated by concerning the effects of selected parameters (particle size, concentration of plasticizer reagent, amount of NaOH, conditioning time and the effect of conditioning temperature). At the end of the experiments, optimum parameters for selective flotation of PET from PVC was found as particle size of -4.76 + 3.36 mm, NaOH amount of 30 kg/t, conditioning temperature of 75°C, conditioning time of 30 minutes, reagent amount of 300 mg/L. Consequently, PET was re-covered with 99.7% purity and 57% efficiency.

Jan 1, 2014

By M. Board, C. Alexander, M. Ramström, W. Johnson

"Hecla - Lucky Friday is an underground mine that has been in operation for 75 years and produces from depths over 2.3 kilometers (7,500 ft) below the surface. Technical issues at this depth include high rock temperature and seismicity. The use of new innovative mechanization is being examined for ore production. Principal advantages of mechanization are the reduced exposure of personnel, reduced seismic triggers, and increased efficiency. Lucky Friday has partnered with Atlas Copco to design, build, test, and deploy a mechanical miner for primary ore production. We will discuss the background, concept, development and deployment strategy for a mechanical miner. BACKGROUND The Coeur d’Alene mining district in northern Idaho was first discovered over 130 years ago and has been the most prolific silver producer in the US. The Lucky Friday mine of Hecla Mining Company (Figure 1) is the oldest (76 years) and deepest mine in the district, producing approximately 725 tonne per day (800 tons per day) from narrow, vertical lead-zinc-silver veins. Cut and fill stoping is currently employed at depths to about 2.3 km (7,500 ft) below ground surface, making it one of the three deepest mines in the western hemisphere. The #4 Shaft, a winze collared at approximately 1.8 km (5,900 ft) below surface and extending to a depth of nearly 2.9 km (9,600 ft), was recently completed to exploit the high-grade 30 Vein, whose resource has been identified to at least 3 km (9,700 ft) in depth.As with other deep mines worldwide, a number of challenging engineering issues occur, including: high in situ rock stress, squeezing ground, seismicity, high in situ rock temperature that requires refrigeration, diesel equipment that generates diesel particulate matter (DPM) requiring high ventilation airflow rates, and long travel times for worker transport to mining areas."

Jan 1, 2018