Search Documents

By B. Markovic

Performance of mineral filler particles in ceramic applications can be enhanced markedly by adsorbing polymers of optimum molecular structure and dosage. In a recent work by Chen and Somasundaran (1997), a novel scheme of controlled polymer adsorption was used to produce nanocomposites of unique core-shell designs. Towards this purpose, adsorption and desorption behavior of selected polyacrylic acids (PAA) on three minerals; alumina, titania, and silicon carbide, was examined as a function of relevant parameters. Adsorption of P AA was found to depend on polymer molecular weight, pH, as well as solids loading. Specifically, the adsorption density was found to increase with increase in polymer molecular weight for non-porous alumina while it was found to decrease in the case of porous alumina. This is attributed to the inaccessibility of the pores to the larger polymers. An unexpected finding was the change in the adsorption density of PAA with solids loadings. PAA adsorbs on silicon carbide only at low pH values when the particles have very low surface charge suggesting that the adsorption in this case is controlled by electrostatic forces. Using polyacrylic acid as bridging agent between the alumina fillers (core) and nanosize alumina or titania particles (shells), controlled layer by layer deposition of nanoparticle on the core particle surface could be obtained.

Jan 1, 1997

THE Company's smelting equipment consists of three blast furnaces, supplied with blast from two sets of vertical piston blowers, each capable of delivering 8000 cub. ft. of air per minute at a pressure of 60 oz. per sq. in. Each blower is belt-driven by a 1:30 h.p. motor. The maximum speed of the blowing engine is 35 r.p.m.No. 1, the largest of the three blast furnaces, has a crucible area of 49.5 sq. ft., and measures 11 ft. 6 in. x 5 ft. at the tuyeres.From tapping floor to feed floor measures 35 ft. 9 in., and holds, when full, 100 tons of charge. Blast enters through thirteen 3-m. tuyeres at 60-oz. pressure. Working normally, this furnace is capable of treating :300 tons of charge, exclusive of returned slag and coke, per 24: hours, with an output of 100 tons of lead. Tapped slag flows into a C.l. forehearth mounted on wheels, where any lead and matte is caught, and the slag overflows into a 3-ton cast-iron pot, in which it is drawn away by an electric locomotive and poured over the dump.

Jan 1, 1918

By Thomas M. Barczak

The engineering of a support system is driven largely by economics. The goal is to provide effective support at minimal cost. For this reason, wood has been extensively used as a support material for centuries. The cost of timber for mining applications has risen by more than 50% in the past 5 years and is likely to continue to increase as the supply diminishes and further environmental restrictions are placed on timber harvesting. The increased cost and lack of high strength wood in the Western United States has provided incentives to improve the utilization of wood and to develop alternative support materials. This U.S. Bureau of Mines' (USBM) report discusses the basic engineering requirements for the application of various materials for supplemental roof support construction and provides an overview of support systems that use materials other than wood. A comparison of support performance and cost for various material constructions is made to assist the mine operator in support selection. The scope of materials discussed in the report include: (1) conventional mine timber loaded perpendicular to the grain, (2) parallel to the grain timber loading, (3) steel fiber reinforced and air entrained concrete, (4) steel, (5) granular fill materials, and (6) combinations of these as composite support structures. The range of support systems analyzed include wood and concrete cribs, concrete columns and props, steel beams, friction props, and several novel support concepts.

Jan 1, 1994

By Antonio Fabiano de Oliveira

The aim of the present research work is to study the influence of hard chrome covered skin pass cold rolling rolls using 2D/3D surface topography, i.e. roughness characterization. The common stochastic structure Shot Blast Texturing (SBT) does not meet all requirements related to the production line regards to the finished product. The Hard Chrome layer, applied on these SBT rolls, can improve the sheet surface quality and is of fundamental interest mainly for those steel mills that do not have another alternative to new surface structures such as those that may be provided by the EDT, LT, EBT, etc. methods. The function of the generated surfaces, obtained by these different methods is going to influence the tribological properties during the subsequent forming processes. On the other hand, they can increase the product final cost or require large investments to obtain such surfaces. The results here presented are in accordance with other recently published research work, showing that there is a relationship between these parameters, and that further detailed studies are needed.

Aug 17, 2017

"The 100,000 volt sub-station at Butte is located near the center of the district in which the power is distributed. The sub-station building is 150 feet by 50 feet in plan and 50 feet high. It is a brick walled, steel framed structure with concrete floors and roof.There are installed at present four banks of single-phase transformers, rated at 3,600 k-w. per bank and connected in delta on both high and low tension sides. They step the voltage down from 102,000 to 2,500, at which voltage it is distributed to customers. The transformers are installed in fireproof compartments, entirely shut off from the rest of the building by brick walls and opening only out of doors. The transformers are mounted on wheels and can readily be run out onto a flat car, which stands on a track running parallel with the building in front of the row of transformer compartments. This arrangement furnishes a convenient method of handling the transformers, both at the time of installation and afterward, in case it is necessary to make repairs."

Jan 1, 1913

By J. Mark Richardson

The use of an integrated software package to simulate and optimize the performance of mineral processing circuits is illustrated by three examples. Each represents application of the software and associated techniques to optimization of an existing plant. In the first example, a South-western U. S. copper company employs the method to simulate and improve performance in crushing, screening and SAG milling. A second copper producer evaluates equipment changes and flowsheet alternatives in a closed-circuit ball mill-cyclone operation. A Southeastern U. S. aluminum refinery optimizes performance of a dry milling and classification circuit for production of carbon particles used in anode casting. Graphical and tabular data describe the circuits simulated and the results achieved in each example.

Jan 1, 1990

By R. J. Allan

"CANADA HAS A GREATER LAKE AREA than any other country. Discountin the Great Lakes, this fresh-water area, mainly in the Canadian Shield, is listed as approximately 300,000 sq. mi. Densities of lakes range up to 7,500 in a 5,294-sq. mi. area of the Shield, southwest of Reindeer Lake, Saskatchewan. Five areas chosen randomly from the Shield (Figure 1) contained sufficient lakes to provide samples at a density of at least one per 10 sq. mi. Regional geochemical surveys in the Appalachian area (Nova Scotia, Boyle et al., 1958; New Brunswick, Boyle et al., 1966) and in the Cordilleran area (Yukon, Gleeson, 1965) of Canada and in many other areas of the world have relied heavily on analyses of stream sediments. These surveys show that sampling of material related to the drainage system reflects the over-all trace element content of the rocks and surficial deposits in the drainage basin. In the Shield, the classic types of dendritic (and other) stream systems found elsewhere in the world are very rare. However, impeded and disorganized stream systems that abound with lakes can provide the exploration geochemist with an ideal composite drainage system sample in the form of lake sediment. This paper attempts to demonstrate the feasibility of, and review the theory and problems involved in, the use of lake sediment as a regional geochemical exploration medium. Most of the references to field examples are taken from a regional survey using lake bottom sediment as the sample medium over 1,500 sq. mi of the Coppermine basalt group and adjacent rocks (Figure 2). During this regional survey, detailed sampling of several lakes was carried out and the results are referred to at appropriate places in the text."

Jan 1, 1971

By Jorge Madias

O trabalho está centrado na análise comparativa de normas de vinte paises/regiões sobre vergalhão, escolhidos levando em conta os principais paises productores, exportadores, e consumidores deste produto para a construção civil. São comparadas as propriedades mecânicas: limite de escoamento, resistência à tração, elongamento à rotura, elongamento uniforme, relação escoamento/tração), a análise química, testes especiais como fadiga e adherência e outros ítens. Tambén é tida em conta a evolução dos quesitos das normas ao longo do tempo. O foco é o comportamento anti seismo do vergalhão.

Oct 30, 2017

By Jaime Herrero, Santiago Gómez, Pablo Segarra, José Ángel Sanchidrián

This paper presents a mathematical model for the study of the 2D movement of blast bench faces based on the high-speed video analysis of three blasts at El Aljibe quarry (Spain) recorded at 2,000 frames per second. In these blasts, a set of bags of 0.75 × 0.75 m were placed in front of a selected blasthole defining a reference plane in which to study the kinematics of the movement. The burdens range from 3.86 m to 5.54 m, with a bench height of 12–13 m. An affine transformation system was calculated to convert coordinates from the video images into actual spatial coordinates. The problem is established from a multi-objective minimization approach in order to simultaneously optimize two defined objectives: trajectory fitting using Total Least Squares regression, and time–displacement regression using Ordinary Least Squares. Muti-objective minimization formulation produces Pareto plots of non-dominated solutions, i.e., optimal combinations of initial velocities and response times, (i.e. time between detonation and the onset of bench face motion). From the Pareto frontier, the most balanced solution is selected. Blast response time lasts only a few milliseconds and appears so brief at the frame rate used that it is difficult to detect visually. In this context, the bi-objective optimization-based approach proves to be a more robust tool than frame-by frame survey for quantifying such a rapid event while also maintaining a strong performance in the trajectory fitting task. Root Mean Square Error (RMSE) for the two minimizations average 0.22 m and 0.13 m, respectively. The initial velocities obtained range from 4 to 17 m/s, and the response times 0.7 ms to 21.7 ms. An analytical model is also presented for predicting fragments initial velocity and response time as functions of blast geometry and rock mass properties, explaining approximately 87% of the total variability.

Jan 26, 2026

By A. D. Zunkel

Increasing amounts of electric arc furnace dust (EAFD) are being generated worldwide as more steel is produced from electric furnace melting of galvanized steel scrap. In most countries, the management of this material is a costly technical, economic, and legal problem for minimill steelmakers. Many technologies and processes are being developed and implemented worldwide to manage this material to recover contained zinc, lead, and iron values and render it nonhazardous. These processes are pyrometallurgical, hydrometallurgical, or hybrid in nature. Some produce zinc oxide, some zinc metal, some lead metal, and some lead cement. Some are successful, some have failed, many are dormant. or abandoned, and others continue to be developed and emerge. This paper updates the current status of 20-30 processes in various stages of commercial application and development used worldwide to manage EAFD and recover its nonferrous, particularly zinc and lead, and ferrous values.

Jan 1, 2000

By F. R. Camisani-Calzolari

Surface defects on continuously cast slabs require treatment by grinding. This extra phase in the process causes lower throughput of final product and extra energy costs. The elimination of slab treatment after casting implies that slabs can be direct rolled or hot charged, resulting in higher throughput and lower energy costs. To increase the number of slabs that can be direct rolled or hot charged, defects have to be predicted before a slab has completed the casting process. Transversal and longitudinal cracking, casting powder entrapment and other inclusions, bleeders, deep and uneven oscillation marks, stop marks and depressions are the defects thatare considered for prediction. A structure with two models is proposed. The first model describes the effect of mould level, water inlet temperature and casting speed (MV?manipulated variables) on 38 thermocouple temperatures (IV?intermediate variable). Casting speed is a manipulated variable while mould level and water inlet temperature are treated as measured disturbances. This model is known as the MV to IV model, and is used to control the occurrence of defects. The second model describes the effect of the thermocouple temperatures on the defects at different positions and locations on the slabs (OV?output variables). This model is known as the IV to OV model and is the predictor of defects. The models are determined using time-series methods in the form of auto regression with exogenous input using data of approximately 500 slabs cast over a period of 6 months. The models are validated using plant data from 44 slabs gathered three years later, with good results. As an example, published results give a sensitivity and specificity of 61.5 per cent and 75 per cent respectively for longitudinal cracks on validation data, while the presented method gives 63.6 per cent and 93.5 percent, respectively. The IV to OV model is used in an inversion to determine the optimal thermocouple temperatures for each slab width. Keywords: Continuous casting, model, defect, prediction, direct rolling, hot charging, goodness-of-fit, correlation, time-series, soft sensor, ARX.

Jan 1, 2003

By V. Blet

Rare earth elements (REE) are regarded today as highly critical raw materials but currently lack suitable recycling processes. A combined hydro- and pyrometallurgical process aimed at REE recovery from used NdFeB permanent magnets was recently developed by the CEA. The process integrates the physico-chemical treatment of magnets, followed by a solvent extraction step for the recovery and intra-REE separation using a selective extractant. A subsequent pyrometallurgical treatment via molten chloride salt electrolysis allowed the isolation of pure Dy metal. Technical-economic assessment and life-cycle analysis were also conducted. Following this first successful demonstration, a new project aimed at the recovery of REE from end-of-life nickel-metal-hydride batteries is currently being developed in association with industrial and academic partners. The project aims at evaluating from an experimental and economic perspective different processes converging at the production of value-added products such as cermet materials for catalytic applications, purified REO concentrates, or metallic alloys.

By W G. Brese

The attention of the world is being focused on the spectacular rise of elemental sulphur production in Alberta. In the short space of a decade, production has increased from less than 10,000 long tons, in 1952, to al-most 1,000,000 long tons in 1962. Moreover, 1963 sulphur production is expected to rise by 50 per cent to approximately 1,500,000 long tons, and further increases are forecast for ensuing years. The reason for this dramatic in-crease in elemental sulphur production, particularly in the last year or two, is that Alberta elemental sulphur is recovered in association with the production of sour natural gas. When very large volumes of natural gas began moving to U.S. markets in the latter part of 1961, the resultant increase in sour gas production led to a marked increase in the production of sulphur. Consequently, Canada, mainly on the strength of sulphur produced in Alberta, will soon become the second largest producer of sulphur in the Free World

Jan 1, 1963

By M J. Gillespie, P D. Erskine

Mine site rehabilitation generally includes the re-shaping of overburden to create a final landform, manipulation of substrates and subsequent revegetation. Due to the wide range of environmental variables that influence rehabilitation progression, having clearly-stated final land-use goals and ongoing significant contributions to the planning process, from prefeasibility through to mine closure, is essential for achieving stable landforms and sustainable rehabilitated communities. Two examples of rehabilitation processes in the phosphate rich region of North West Queensland are used to illustrate some of the possible benefits of early planning and communication of rehabilitation requirements.Approximately 160 km south of Mount Isa, Incitec Pivot Limited operates a 35 year old open cut mine at Phosphate Hill. Monitoring of rehabilitation areas and selected analogue sites is undertaken annually, but the initial landform design, substrate management and species selection has created a difficult environment for revegetated areas to successfully establish. Constant management input (such as weed management, erosion control, supplementary seeding, etc) will, therefore, be required over a long time frame.The second example uses exploratory drilling and historic costean pits at Legend International HoldingÆs Paradise South site, 135 km north of Mount Isa, to determine the success of natural vegetation colonisation on waste rock and compacted soils, and the effects of cattle grazing on recolonisation. This information can be used by planners of the mine life to inform possible end-land use decisions and proposed completion criteria.In a semi-arid environment such as North West Queensland, the creation of a post-mine landscape suitable for nature conservation and/or grazing can be an arduous task. The input from environmental personnel at all stages of the mining process will positively impact upon the quality of the resulting rehabilitation and ensure undesirable legacy issues are minimised.CITATION:Gillespie, M J and Erskine, P D, 2012. Importance of early rehabilitation planning - Case studies from North West Queensland, in Proceedings Life-of-Mine 2012 , pp 187-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By A. Sand

A 2-dimensional computational model based on the discrete element method (DEM) is utilized for modeling of stamp-charged coke making. In this process, a large volume of coal is compacted to one single coal cake before entering the coke oven. Cake densification and mechanical strength development are key factors for the subsequent production of a high-quality coke. An approach is introduced for model calibration utilizing multiple control parameters obtained from a laboratory-scale stamping device. Experimental data on stamper rebound amplitude, attenuation and peak force are compared with simulation output in a pairwise manner by constructing a criteria space, which allows identification of model settings best satisfying the control parameters. The calibration procedure carried out by multiple criteria comparison aided model parameter selection for reproducing stamper behavior in response to the properties of the cake subjected to compaction. This modeling and calibration procedure offers possibilities for numerically studying the densification and mechanical strength development of coal cakes. However, the approach is also more widely applicable to other compaction processes.

Feb 27, 2013

By A. J. Antony Chettupuzha

During a construction project, it is important to ensure that accurate and pertinent knowledge is delivered on time to appropriate personnel. The criticality of documents exchanged or referred to by various parties, evolves over the course of the project lifecycle. Determining the criticality of documents at different stages of the project can aid companies with managing the flow of information in an organized manner, while providing for the detection of potentially disruptive, erroneous material that could result in delays and costs. Therefore, it is crucial to determine documents which have the potential to disrupt a process (by virtue of being incorrect versions etc.) so that they may be isolated or prevented from entering or interfering with the active flow of information in a project, while also ensuring standard revisions of documents are recognized and accessed accordingly. Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project. Analyzing an EPPM system may yield information about the criticality of certain documents within an activity, as well as isolate characteristics peculiar to documents which can assist in risk mitigation. We propose methodology that identifies such critical documents.

Aug 1, 2013

"A fire design innovation of the concrete lining of the Ohio River Bridges East End Crossing Tunnel has been developed. As a result from a fire suppression and tunnel ventilation system, the project design Heat Release Rate (HRR) was able to be constrained from 300 MW to about 50 MW. With this reduced HRR, concrete lining without passive fire protection may be acceptable, if the tunnel concrete lining will not result in explosive spalling during the designed fire event. Concrete explosive spalling test was proposed to verify this assumption. Since no standard concrete fire explosive spalling testing procedure exists, a project specific testing procedure was developed and fire tests conducted. From fire test results, it is concluded that the proposed tunnel concrete lining, in conjunction with the proposed fire suppressing and ventilation system, will not experience explosive spalling and does not require a passive fire protection system. INTRODUCTION The Ohio River Bridge East End Crossing Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The Tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining consists of 16 inches cast-in-place concrete lining and 20 inches invert slab, with a waterproofing system around the tunnel perimeter. Two (2) tunnel side drains and one (1) invert drain were provided for each tube. This paper describes the rational in assessing fire design requirements of the tunnel final concrete lining, to answer the question whether a passive fire protection system is needed or not."

Jan 1, 2016

By J. G. Russell

The valuation of known mineral re-serves entails the economic evaluation of the mining enterprise and the valuation of other assets employed, including mining and processing plant and intangible assets. A case study approach analyzes two reserve situations: ownership of reserves (phosphate rock), and leasing of reserve lands (kaolin). The appraisal of the physical property is outlined, along with the economic analysis of the operation. The discounted net cash flow approach is used to value the enterprise, leading to value of the reserves after correlation with other assets employed.

Jan 1, 1989

By John A. Herbst

The Mineral Processing Industry needs accurate Production Simulators for the design of future plants and expansions. To achieve this, these simulators should not only provide an accurate portrayal of the dynamics of individual pieces of equipment they should include the impact of discrete stochastic events such as scheduled and unscheduled maintenance so the relationships between availability, equipment sizes, and plant capacity are understood. To provide such a tool accurate dynamic Population Balance Models need to be combined with solid discrete event modeling. The current paper provides a description of how these two disparate modeling techniques were combined and the associated benefits from this combination. Keywords: dynamic plant simulation, population balance models, discrete event models, prefeasibility and feasibility studies, plant design and expansion

Sep 1, 2012

By G. Akdogan, I. J. Geldenhuys, Q. G. Reynolds

Efficient recovery of titanium from titaniferous magnetite ores continues to be a promising, yet unrealised opportunity, despite significant occurrences of titaniferous magnetite deposits worldwide and the existence of established industrial-scale practices. Current smelting processes only recover iron and vanadium, while the titanium is discarded in the waste slag. These slags are stockpiled and present massive environmental challenges, while still containing value as residual iron, vanadium and titanium. The complex mineralisation of these deposits does not allow for a significant opportunity to separate the titanium and magnetite minerals through normal physical upgrading processes. An upgrading process is therefore required to derive economic value. An efficient process technology could create an opportunity to unlock all three valuable commodities. South Africa’s Bushveld Complex, the largest known deposit of its kind in the world, is known for the high vanadium content but is also associated with relatively high concentrations of titaniferous magnetite. The quality of the Bushveld Complex was one of the drivers for the establishment of the Highveld Steel and Vanadium Company in the mid-1960s. The unfortunate demise of Highveld Steel and Vanadium created an opportunity to review current practices and evaluate the best available process for this complex ore in the context of the three elements of interest. Past and current processes, the nature of these deposits and the potential to recover titanium are assessed to highlight the potential of fluxless smelting of titaniferous magnetite to produce a titania-rich slag as feedstock to the pigment, titanium metal industry in conjunction with recovery of iron and vanadium. Ilmenite smelting practices are proposed as a suitable alternative to achieve the goal, namely sustainable processing. Keywords: Titaniferous magnetite, titanomagnetite, smelting, titania slags, comprehensive processing

Jan 1, 2020