Search Documents

By G. R. St. Pierre, S. W. Gilby

The equilibrium vapors established over Fe-Cr-Ni alloys containing up to 50 pct Cr at 1600°C were determined by collecting the effusate from thoria Knud-sen cells. From these data, the activities of iron and nickel in the ternary alloys have been calculated. In a separate set of measurements, a mass spectrometer was used to determine the activities of the three components in a series of Fe-Cr-Ni alloys. In binary Ni-Cr melts, the activity coefficient of chromium referred to pure solid chromium as standard state is less than one at low chromium contents but is greater than one for melts containing more than 30 at. pct Cr. For Ni-Cr melts containing less than 10 at. pct Cr, In ?Cr = 0.15-0.92 N2. Ternary activity diagrams for Fe-Cr-Ni alloys are presented. In iron-rich alloys, the interactions between the three components are negligible; however, in nickel-rich alloys, the three principal interactions have significant positive values. THE activities of components in binary Fe-Ni alloys have been measured both in the solid solution1-3 and liquid solution4-6 temperature ranges. The determination for Fe-Ni melts have been made by three different methods: transpiration,4 Knudsen-cell effusion with analysis of an accumulated condensate,' and Knudsen-cell effusion with direct measurements of relative component intensities by mass spectrometric methods.6 The results obtained by the three different methods in three different laboratories are in excellent agreement and considerable confidence is placed in the activity coefficients for Fe-Ni melts. At 1600°C, the activity coefficients in dilute solution are ?°Ni = 0.66 and ?oFe = 0.40 for the pure liquid components as standard states. Measurements made on solid solution Fe-Cr alloys7-10 indicate that the component activities are slightly greater than ideal. The measured activities in iron-rich Fe-Cr liquid alloy11-16 indicate almost ideal behavior for this system. The recommended activity coefficient of chromium in dilute solution in liquid iron at 1600o C, ?oCr, is 1.18 when referred to pure solid chromium as standard state and 1.04 when referred to pure undercooled liquid chromium as standard state." The conversion factor of 1.14 is based on a melting point of 1857°C and an enthalpy of melting of 4047 cal per g at. for chromium.21,37 The activity coefficient of iron in dilute solution in liquid chromium has not been measured. Activity measurements on solid Ni-Cr alloys have been made by several investigators.17-20 During the review of this manuscript, Fruehan12 published the results of a study on liquid Ni-Cr alloys at 1600°C. He used galvanic cells22 with ZrO2(CaO) as the electrolyte and Cr/Cr2O3 for the reference electrode. His results indicate that ?oCr in nickel at 1600°C is about 1.01 when referred to pure solid chromium and about 0.89 when referred to pure undercooled liquid chromium as standard state. The activity coefficient of nickel in liquid chromium is unknown. The compositions of vapors freely evaporating from some molten Fe-Cr-Ni alloys have been measured by Lyubimov, Granovskaya, and Berenstein.23 Their results, combined with known vapor pressures, indicate strong positive deviation for chromium in iron-rich alloys and strong negative deviation for chromium in nickel-rich alloys. EXPERIMENTAL PROCEDURES This research was undertaken to determine the activities of components in ternary Fe-Cr-Ni melts containing up to 50 at. pct Cr. At the initiation of the research, we decided to use a Knudsen-cell method wherein a portion of the effusing vapor is condensed on a cold plate.' The composition of the equilibrium vapor for each alloy composition is determined in this method by holding the system under constant conditions for a period of time sufficient to collect enough condensate on the cold plate for chemical analysis. The activities of components in ternary alloys can be calculated from such vapor composition determinations by Eq. [1].24

Jan 1, 1970

By M. Bhartia

India is the 5th largest producer of steel in the world and is slated to produce more than 180 Mt by 2020. Expectedly about 50 % of this would be through the Blast furnace route and the rest through Sponge iron / DRI route. Considering that there will not be any major change in iron making technology by that time, the Blast operation would require lump ore (10-40mm) with around 64% Fe grade and sinter fines (<10mm) with 60% Fe (min) as its feed. DRI process would need calibrated ore of size 5-18 mm as the most suitable size of feed. It is also expected that of the total requirement of ore for the DRI route a significant part would be DRI pellets. In India, there is considerable debate going on regarding the technology to be adopted for the processing of iron ore and there is a lack of clear consensus. The above scenario indicates that the processing requirement of iron ore in the country would involve both washing technology as well as beneficiation technology. CDE Asia Ltd is in the forefront of iron ore processing in the country and the experience gained by the company over the last few years of functioning has led the company to believe that route to be adopted depends on the end product requirement and the starting grade of the feed. Keeping in mind the nature of the feed required for the Blast furnace & DRI operation; it is obvious that good washing technology would be highly beneficial to the iron ore industry. Depending on the grade of ore available the limits of washing will be decided and equipment for lump ore beneficiation such as jigs could be incorporated into the washing circuit. Scrubbing of ore either before washing or selectively scrubbing the lumps could be necessary. Very low grade ore and jig rejects would be required to be totally ground and beneficiated for the production of pellet feed in order to utilize the iron ore resources entirely. Another source of ore for pelletisation would be slimes generated from the washing process as well as the huge quantities already available in the tailings dams in the operating mines. Deslimimg and magnetic route of beneficiation could release at 30-40% of the Fe locked up in these tailings ponds/dams. The paper describes the concept with examples from operating plants and proposes how the adoption could be engineered through test work and proper plan of integration. Keywords: washing, beneficiation, iron ore, lumps, sinter fines, pellets, jigs, screens, evowash, nanowash, thickeners, log washers, drum scrubbers

Sep 1, 2012

By Gregg Hodges, Fred Schoenbrunn, Steve Slottee, Chad McCleary

"In December, 1999 Stillwater Mining Company (SMC) commissioned a new paste /cement backfill plant to supplement the existing sand backfill system for the cut and fill mining operation at it’s Nye, Montana mine. The new plant uses the Baker Process Deep Cone TM Paste Thickener to thicken the total concentrator tailings from 30% solids slurry to a 71% solids paste. This paper describes both general paste formation concepts and the evolution of the SMC paste plant operation from original design criteria, through problem solving and plant modifications, to the operation of the existing plant.Although the original process design was not effective for consistently producing and delivering acceptable paste to the stopes for backfill, SMC was able to make the mechanical and process modifications which allow the plant to now produce and deliver an acceptable product to the stopes. Ongoing test work is targeted at increasing the pumping range of the system, increasing the paste solids concentration from the Deep Cone Paste Thickener and reducing the operating and maintenance costs of the system.INTRODUCTIONThe authors would like to thank both Stillwater Mining Company (SMC) and Baker Process for their assistance in the preparation of this paper. Stillwater Mining Company chose not to participate directly in this paper due to time constraints, but was very helpful in answering questions concerning their approach to problem solving and specific details with regard to engineering criteria.This paper will begin with a general review of the technical and mechanical concepts in paste formation and then focus on the overall design, start-up and problem solving process for the paste backfill operation at SMC’s mine and concentrator near Nye, Montana."

Jan 1, 2001

By M. J. Lukhele

Paper written on project work carried out in partial fulfilment of B. Tech (Mining Engineering) degree A number of high wall mining methods were developed over the years to mine coal reserves exposed on the high walls created during surface mining. The auger mining system was initially developed in the early 1940s in the United States of America. High wall mining is a method of recovering coal from seam exposed either by mechanical excavation methods or natural erosions. This is usually associated with strip-mining (opencast) where the stripping ratio is high and uneconomical to mine using the opencast mining method. This paper discusses the surface auger mining as deployed at Rietspruit Mine Services Proprietary Limited.

Jan 1, 2002

By T. Plikas, T. Porretta, M. Al-Dojayli, B. Pretorius, J. Woloshyn, H. Ghorbani

"Water-cooled ducts represent an integral part of high temperature off-gas systems in metallurgical processes. Typically, off-gas enters these ducts at significantly elevated temperatures; therefore, water cooling may be required to maintain the duct skin temperature within allowable design limits. These off-gases are typically of high mineral content that could lead to dust buildup, and there is a possibility of slag buildup / molten metal splashing. Therefore, dust cleaning provisions may be necessary in order to remove or minimize accretion on the duct wall, which could otherwise impact the water cooling and the system process efficiency. These ducts may have complex geometry and experience a wide range of loading, including gravity loads, water and gas pressures, cyclic thermal loading and dynamic impact forces. Consequently, the thermo-mechanical assessment of such water-cooled ducts is critical and requires consideration phenomena such as high temperature gradients, potential nucleate boiling, thermal ratcheting and fatigue failures. Such assessment is not comprehensively covered by design-by-rule design codes and guidelines due to its complexity. This paper presents a successful implementation example of design-by-analysis methodology to improve the design and extend the life of a water-cooled furnace transition duct using Computational Fluid Dynamics (CFD) and Finite Element Analysis (FEA).INTRODUCTION Water-cooling represents an important part of high temperature off-gas systems in metallurgical processes. Typical temperatures of the off-gas in the furnace uptake are in excess of 1400°C, and thus there is a need to maintain the water-cooled duct and jacket skin temperatures within their material allowable design limits. Water-cooled channels have been used effectively in arc furnace roof design (Sosonkin et al., 1972; Smolyarenko and Khainson, 1988) and other furnaces as well as in furnace fuming jackets (Scholey et al., 1994). The design of these systems was based on one-dimensional analysis to ensure sufficient cooling is available under extreme furnace conditions (Smolyarenko and Khainson, 1988; Scholey et al., 1994). With advancement in furnace and fuming system designs, water-cooled duct designs have become more complicated in geometry. Numerical techniques, such as three-dimensional fluid flow and heat transfer modeling, are therefore needed to more accurately calculate water velocity, temperature and convective heat transfer coefficients in the water-cooled channels (Haywood et al., 2002; Henning et al., 2010). This is of particular importance around geometric corners where stagnant water flow may lead to local nucleate boiling at the critical heat flux, causing hot spots (Bergman et al., 2011). High wall skin temperatures increase the risk of failures due to thermal stresses as well as increasing corrosion rates (Gelfi et al., 2012), leading to costly equipment downtime and potential safety risks."

Jan 1, 2017

By James F. Archibald, Ferri Hassani, Jacques Nantel, David O. DeGagné

Operators depend upon the success of backfilling programs to ensure that mine activities run continuously (Archibald et al, 1993) where backfilling is an integral part of the mining cycle. In order to ensure that the backfill is prepared and delivered to the stope possessing the required engineering properties, as designed, and that the backfilling process is safe, mine operators at all stages of the backfilling system must be adequately trained for their tasks and be aware of how their work affects other backfilling stages, both up- and down-stream of their station. Mine operator training is primarily based on learning on-the-job from experienced supervisors or training personnel. Classroom training and the availability of reference manuals are less common. While in use by many industries for some time now, computer-based training (CBT) is becoming more readily accepted by the mining industry for a wide variety of training. It is not intended to replace on-the-job training, but to augment it. CBT offers many advantages to enhance operator learning by utilizing multimedia presentations, interactions and on-line testing to teach complex concepts and relationships. Discussions with many operations revealed that there is an industry need for a backfill guide for frontline operator training and as a reference manual for operators and mine engineers. Sponsored by the mining industry and the CIM, "Mine Backfill, An Operator&apos;s Guide" has been developed by the Departments of Mining Engineering at Queen&apos;s University and McGill University to fulfil this need. "Mine Backfill, An Operator&apos;s Guide" is an interactive multimedia package that incorporates high quality colour images, animations, sound, and video with text to review the main backfill methods employed in Canada, including hydraulic/slurry, paste and rock fill. The Guide is divided into training and reference primer sections. When in training mode, the operator is guided through a presentation of common mining and backfill practices and technologies so that he/she may become more familiar with different aspects of backfill processes. To ensure that key concepts have been learned during training, the operator will be tested after each section using a series of multiple choice and true/false questions. When in reference mode, alternatively, the operator may browse through the information in a more detailed and independent fashion through a series of interactive menus. The Guide focuses on the following main topics: resources, surface preparation, distribution, stope activities, health and safety, and quality control. Special features included in the Operator&apos;s Guide are a Buyer&apos;s Guide, a Trouble Shooting Guide, and an interactive glossary of backfill and mining terms. Concepts in interactive and computer-based learning are also reviewed in this paper.

Jan 1, 2001

By D. H. Mullen, S. M. Runke, J. B. Cunningham

"SUMMARYThe coarse-grained granitic pegmatities of the United States have long been a source of many important industrial minerals, because of this, they have been studied intensively by geologists, mining engineers, and metallurgists. These studies have amassed a rather astounding array of published and unpublished information.Correlation of geological studies between individual pegmatites, as well as between major districts, has brought forth some semblance of order to the knowledge of the structure and Mineralogical composition of those highly complex and irregular deposits, making it possible to classify certain prgmatitites and pegmatitec zones into several groups of associated minerals; based upon the presence or absence of the minor minerals of beryllium and lithium. This classification or grouping of minerals, with the methods that have been developed for recovering certain of these minerals, makes possible a systematic approach to the winning of many of the industrially important minerals from pegmatite rock by a single integrated process.As the coarse-grained granitic pegmatites are composed primarily of,feldspar, quartz, and muscovite, the methods developed for separating and recovering them, as well as those methods developed for separating and recovering such minor minerals as spodumene and lepidolite, are important contributions to the over-all problem of pegmatite treatment. Some of these methods have been demonstrated in the laboratory only, whereas others have progressed beyond the laboratory stage arid are being employed in commercial operations.Recent laboratory investigations at Rapid City, employing both these early developments and the mineral groupings, have demonstrated that a single integrated process can recover muscovite, feldspar; and. quartz from the rejects of hand-sorting a typical muscovite-feldspar-quartz material. Employing a newly developed procedure for the flotation of beryl, the investigations have also demonstrated the possibility of recovering the beryl, in addition to muscovite, feldspar, and quartz, by an integrated process from a typical berylliferous pegmatitic material in which all of these minerals are present."

Dec 1, 1952

By A. E. Kehew

Earth resistivity surveys using the Wenner electrode configuration were made in unmined areas and reclaimed spoils at three surface lignite mines in western North Dakota. The study sites were the Center, Indian Head, and Falkirk Mines. Automatic interpretation of the curves was accomplished with the method of Zohdy and Bisdorf (1975). Overburden materials become more homogeneous with respect to resistivity during the mining and reclamation process. The spoils curves show localized hetero-geneities probably related to discontinuous moisture content variations in the spoils. Consistent resistivity differences in spoils occur between mines with over-burdens of different mineralogic compositions. Groundwater chemical composition in terms of total-dissolved-solids (TDS) is inversely correlated (r=-0.61) with apparent resistivity at the 80-foot spacing from a survey centered at a piezometer screened near the base of the spoils. Better inverse correlation is probably pre-vented by high variability in TDS within the spoils groundwater. A useful predictive relationship may be the plot of mean apparent resistivity at the 80-foot spacing for ar. entire mine against mean TDS for all wells in spoils at that mine. Data from more mines are needed to test the hypothesis.

Jan 1, 1982

By Samuel Hoyt

THE hardness of annealed copper has been given in the literature and is easily obtained by any of the standard methods of hardness testing. It is not our intention to correct published values or to add to them, but to describe tests of two bars of annealed electrolytic copper in which the methods of Meyer&apos;s analysis were employed. MEYER&apos;S ANALYSIS OF BALL INDENTATION TEST The ball indentation test is probably the most valuable hardness test we now have but, as it is carried out in the Brinell or Rockwell test, the result may be seriously in error without the operator suspecting such to be the case. This condition results from the isolated and uncontrolled nature of the measurement. The accuracy depends on the accuracy of the equipment and the care and skill used in the operations; there is nothing in the impression diameter, which is all that is measured, to indicate the presence of error. Meyer&apos;s analysis supplies a control of the measurements that goes far toward eliminating unsuspected errors. The principles of this work maybe obtained from elsewhere.1 As this subject has not received the attention of this Institute, it may be well to summarize the more important points as follows.

Jan 2, 1926

By Do-Hyeong Kim, Jong-Jin Pak, Jung-Mock Jang, Min-Kyu Paek

"Thermodynamic relations among Mn, Al and N in liquid iron were studied by measuring the effect of Mn on the solubility product of AlN in liquid Fe-Mn-Al-N alloys in the temperature range from 1773 to 1873 K. The critical Al and N contents for AlN formation were determined by the metal-nitride-gas equilibration technique over wide ranges of melt composition and temperature. The effects of Mn on N solubility in Fe-Mn and Fe-Mn-Al melts containing Mn up to 26 mass% were separately determined in the same temperature range. The experimental results were thermodynamically analyzed using the Wagner's formalism to estimate the critical Al and N contents for the onset of A1N formation. The validity was checked by the observation of inclusion evolution in Fe-20%Mn-1.5%Al-0.6%C-0.3%Si-0.012%N melt during cooling and solidification.IntroductionRecently, high manganese steels such as Twinning Induced Plasticity (TWIP) steels have been developed as next generation steels because of their high formability as well as excellent strength and ductility.[1•2l In these steel grades, a large amount of Mn (15-20 mass%) and Al (1-2 mass%) are added to liquid steels, and such high Mn and Al concentration bring the great challenges to the steelmaking and casting processes. Mn significantly increases the N solubility in liquid iron and the AlN inclusions can be easily formed at such high Al concentrations due to high affinity of Al and Mn with N in liquid steels. Although the AlN inclusion is known to be a dominating and considered as a detrimental phase for the hot ductility of steels,l3l thermodynamics of AlN formation in high Mn-Al alloyed liquid steels was not well known.Moreover, the melting point of these steels decreases down to near 1623 K as increasing Mn content up to 20 mass%. However, most of thermodynamic data has been measured at the steelmaking temperature around 1873 K. Even at steelmaking temperature, there are huge scatters in thermodynamic interactions of Mn and Al on N in liquid iron. The nitrogen solubility in Fe-Mn alloy melts has been measured using the Sieverts' method[4l and the samplinij method[5-7J in the temperature range of 1813 to 1973 K. In the authors' recent study,[8•9 the N solubility in Fe-Al alloy melts was measured using the sampling method in the temperature range of 1823 to 1973 K. However, the simultaneous effect of Mn and Al at high concentrations on Nin liquid Fe-Mn-Al-N alloys is still not known. Also, there remains uncertainty about the temperature dependence of the interaction parameter of Mn on N in liquid Fe-Mn alloys. Therefore, it is worthwhile to check the temperature dependence of this parameter at a low temperature near the melting point of Fe-Mn alloys. There have been few studies on the characterization of non-metallic"

Jan 1, 2014

By Jon Hurt, Brent Meins, David Vardiman

"Two test blasts were conducted at the Sanford Underground Research Facility to establish optimum blast designs and to limit blast effects on existing research rooms and equipment in preparation for the largest deep underground excavation in North America. Located on the 4850 Level (4,850 ft below the surface)at the former Homestake Mine in Lead, SD, this excavation is part of the U.S. Department of Energy’sLong-Baseline Neutrino Facility that will house particle detectors for the international Deep Underground Neutrino Experiment hosted by Fermilab. A large array of seismographs was deployedthroughout the 4850 Level to measure ground vibrations and airblast pressures in tunnel drifts and in lab spaces."

Jan 1, 2017

By M. J. Blattman

The problem of measuring the amount of rock removed during a given time interval is faced by most milling operations. Many methods have been developed with varying degrees of success, dependent upon the mining method and the availability of usable data. The Rosebud Mine has been in production for nearly two years, employing several techniques to estimate monthly production from underground production stopes. The use of three-dimensional solids generated from survey data has greatly improved the reliability and confidence of monthly production reports. The authors will summarize the methodology currently being utilized at Rosebud.

Jan 1, 1999

By A. W. Gauger

WITHOUT QUESTION the Commonwealth of Pennsylvania contains the most remarkable coal deposits of the whole world. Within its borders ,are to be found excellent coals ranging in rank from the high volatile bituminous of the western part of &apos;the state through the low volatile or semi-bituminous of central Pennsylvania to that aristocrat of solid fuels, anthracite, found in the East. . . . But while other states and even the Federa1 Government have recognized the needs of the coal industry, Pennsylvania has not. Though bituminous coal represents one of the most important industries in the state, far more important in annual productive wealth than agriculture, for example, hundreds, of thousands of dollars have been spent on agricultural research whereas little or nothing has been spent on coal investigation.

Jan 1, 1932

By Babu K. V., Samyukta P.

The energy demand in India is expected to show increasing growth in the next few decades. The oil companies in India are revamping the existing oil refineries as well as constructing new refineries across the country to meet the energy demands. Most of the refineries in India are located along the coastal region because of the ease of transporting crude materials. Considering the criticality of the structures as well as soil conditions in the coastal region, pile foundations are used in refinery plants. In India, non-displacement piles in the form of bored cast-in-situ piles are used to support structures. In a few circumstances, displacement piles in the form of driven cast-in-situ piles are also being used to support critical structures. This study presents the performance of non-displacement and displacement piles for similar ground conditions at the same project location. The pile load test results have shown that the settlement observed for displacement piles is lower than compared to non- displacement piles for a given loading and soil conditions. This shows that the performance of displacement piles is slightly better in comparison with that of non-displacement piles.

Sep 1, 2022

By Herbert D. Drechsler

The objective of this paper is to identify the components of income above that necessary to keep a mine in production and relate those components to the profits of a mining firm. This is a discussion of "Economic Rent". Economic rent is the payment to the factors of production -- capital, labour, entreprenuer and the owner of the mineral deposit -- above the minimum necessary to keep all of these factors cooperating in the production of minerals from a particular deposit. THE SOURCE OF ECONOMIC RENT IN THE MINING INDUSTRY In the mining business each mine has a unique cost of production unrelated to any other mine. The cost of production is developed from many factors such as the technical characteristics of the deposit: depth of deposit, depth of overburden, areal extent, and type of deposit. Furthermore, there are locational factors which also alter cost of production. For example, identical mineral deposits located in Zambia or in the southwest U.S.A. would have different capital and operating costs. These differences occur because of different qualities of labour, ease of acquisition of operating supplies or investment capital and other similar factors. To explain the source of rent, we shall use ideas developed by Alfred Marshall and Kenneth Boulding. Suppose a meteorite with special qualities exploded over earth and sent showers of small meteorites to the ground in various places. At some point in time, people learned of the special qualities of these meteorites and a demand arose and one mine was started. Suppose further that the cost of production to produce these meteorites was different for each deposit. Probably the lowest unit cost mine would commence production because if a higher unit cost mine started-up, eventually someone would discover a deposit that had a lower unit cost of production. The lower unit cost mine would take over the market and the high unit cost mine would cease production. The cost curve for the first mine would look like the following Figure 1. [ ] The output for the first mine is on the horizontal axis with the cost per ton on the vertical axis. The curve labelled AC I is the average total cost of production over the range of possible production that could occur at the property. The total costs are composed of variable costs, which are dependent on output and fixed costs, which are dependent on time. For example, the cost of operating supplies would be a variable cost and normal profit would be a fixed cost.1 The opportunity cost of the investment would also be part of the fixed costs. In our example, all factors of production, are receiving the minimum necessary payment that will keep the mine operating. The average total cost curve is U-shaped because at zero output, the meteorite mine has no variable costs, only fixed costs which, on a unit basis, obviously are very high. To produce a small output of meteorites, the mining firm adds

Jan 1, 1985

By A. González

Arsenic is one of the main contaminants present in Chilean copper concentrates and its abatement represents a challenge for the process metallurgy, particularly under the strong environmental requirements in the global community. The possibility to form ferric arsenate directly from a gas phase by means of a heterogeneous reaction between an arsenic gas bearing and iron oxide was studied at laboratory scale. A thermodynamical analysis for the system Fe-As-O-S has been initially made, in order to obtain the stability conditions for the ferric arsenate or other FeAsyO2 type compounds. Experiments were made using an hematite sample suspended in a thermogravimetric device. AS4O6 gas generated from solid AS2O3 that was passed through the iron oxide sample and its instantaneous weight change was recorded directly. A kinetic study for the AS4O6 volatilization was made to control the gas composition. A chemical control between 300 and 600°C with an apparent activation energy of around 14 Kcal/mol As2O3 was determined. The samples after the reactions were chemically and XRD analysed. Arsenates detected corresponds to complex compounds. Results shows a dependence on temperature and oxygen content in the gas phase. The kinetics for iron arsenates formation is slow, reaching an arsenic capture of 6% after 80 minutes of reaction when an oxygen content of 50% is fed continuously at 800°C and 3,56% As in the gas. Experiences made at the same temperature but under higher oxygen content in a closed reactor, allowed arsenic capture close to 60%. For higher temperatures the capture is considerably lower.

Jan 1, 2003

By I. S. Blair

The Mufulira smelter (1, 2,&apos; 3, 4,) is one of three smelters situated on the Zambian Copperbelt to treat concentrates and other intermediate products produced in the area. Two mining companies, Roan Consolidated Mines Limited (RCM) and Nchanga Consolidated Copper Mines Limited (NCCM) each have 51% Zambia Government participation. RCM operates two smelters, one at its Mufulira Division and the other at its Luanshya Dl vision. NCCM operates one smelter at its Rokana Division (5). The Mufulira smelter was commissioned in 1937 with two reverberatory furnaces and four converters. The final product, blister copper, was cast from a holding furnace. In 1952 two anode furnaces and a common casting wheel were installed to feed a new and adjacent electrolytic refinery. In 1956 the smelter was extended to accommodate increasing production from the new Chibuluma mine and expansion at Mufulira mine. A third reverberatory furnace, a fifth converter and duplicate anode processing and casting facility were added. The Copperbelt smelters suffered a loss of production potential when higher ash content coals were used in reverberatory smelting furnaces from 1966 onwards. This, and the planned production increases from Mufulira and other RCM mines, indicated a smelting shortfall of 55,000 tonnes of copper a year in the combined capacity of the RCM smelters.

Jan 1, 1976

By D. G. Hattingh, A Els-Botes

"Considerable information is available on the factors influencing the iron-zinc reaction rate at 450° C of low carbon steels, in comparison there is a scarcity _of similar fundamental information of spheroidal graphite irons. This can be attributed to the more complex microstructure and ferrous alloy chemical analysis of spheroidal graphite irons. Hot-dip galvanizers have identified the complexity in controlling and predicting the thickness of the galvanized coating formed on commercial cast irons, which has serious financial implications for both the galvanizer and customer.Commercial hot-dip galvanizing has been in use for over 160 years and yet an elementary understanding of the dynamics associated with the hot-dip galvanizing of spheroidal graphite cast iron is still insufficient. To allow the. process to become a modem surface engineering technology, the fundamental aspects of the process must be thoroughly understood.When a clean iron or steel article is dipped into the molten zinc, zinc initially solidifies around the steel or iron. As heat is transferred to the article form the bath, this initial solidified zinc layer remelts and a series of iron-zinc alloy is formed by the reaction of the zinc with the surface of the article; on removal from the bath, some of the molten zinc is taken out on top of the alloy layers. At normal galvanizing temperature (450 °C), the reaction between iron and zinc is usually parabolic with time. The rate of reaction is rapid at first but then slows down and the coating thickness does not increase greatly if the article is immersed in the bath for longer times(1)."

Jan 1, 2000

By M. Jahazi, J. Gholipour

Design and manufacturing of parts using hydroforming process require knowledge about material behaviour and tribological effects during hydroforming. Lubrication is one of the key issues in successfully hydroform the tubes. A Ni-based super alloy tube with 50.8 mm (2 inches) outer diameter and 0.9 mm (0.035 inches) thickness is considered for this research to study the effect of lubricants on the formability of the tubes. Hydroforming of a hollow compressor blade is considered for this project. A combination of press forming and hydroforming is employed to produce the part. LS-DYNA, an explicit dynamic finite element code, is used to model the experiments. Different lubricants are modeled using different coefficient of friction in the model. Predicted results for strain distribution at a critical section of the tube are extracted for each case to evaluate the effect of different lubricants on the process.

Jan 1, 2006

By Claude Lorenson

"The Spyrometer™ imaging pyrometer brings new dimension of imaging capabilities to temperature measurement technology by combining a high temperature video camera with scanning optical pyrometry. This gives the operators the ability to observe process conditions while measuring the temperature of virtually any object or region in the field of view. Since the lens tube of the camera can be air or water cooled, it is possible to see inside furnaces giving a very good view of many different types of metallurgical processes. Specific benefits in process knowledge and maintenance tasks for furnaces in different types of metal industries are discussed.1-Principles of Imaging PyrometryLens tube, camera and processorImaging pyrometry is the combination of video imaging and computer-driven pyrometry that measures the temperature of certain zones (selected by the operator) within the image viewed on the monitor screen. To obtain a detailed image of the metallurgical process under observance, it is necessary to place the optical objective of the camera close to the process. The Spyrometer™ (which is Quadtek's tradename for its imaging pyrometer) objective is housed in a lens tube that is cooled and permits insertion inside the vessel of interest. The length of the lens tube is chosen on the basis of making sure that the tip of the tube is just beyond the refractories lining the inside of the furnace. In most pyrometallurgical processes, we have found that the most reliable system set-up uses a water cooled shroud to cool the lens tube optics. A sapphire window provides maximum protection from the environment. Even in the case of the water cooled version, there is an air purge for the lens that keeps the objective clean and protects against hot metal splashes."

Jan 1, 1997