Search Documents

By Donald Little, Larry Unger

This paper will give a detailed insight into hard rock, large diameter surface blasting including some practical tips to improve blasting practices. These tips will be non-technical, of the nuts and bolts type, intended to help the man in the boots. The paper will begin with the importance of communication between the engineering department and the blasters. What looks good on the mine development map might not blast very well. Tight inside corners, 90 degree outside corners, too few rows; are a few of these problems.

Jan 1, 2006

By Michael J. Pazuchanics

This report documents the current status of the U.S. Bureau of Mines ongoing investigation of the use of adaptive signal discrimination (ASD) systems to distinguish between cutting coal and cutting rock. Cutting-tool forces and vibrations were measured in the laboratory using both conical bits and roller cutters in a linear-cutting apparatus for several material samples and two cutting directions. A number of ASD systems consisting of one or more signal classifiers were trained and tested to study how data window size, type of signal feature, and combining (polling) of classifier results influence system performance. The results show that ASD system recognition rates can be improved by increasing data window size, removing air-cutting portions from the signal data, overlapping data windows, and combining (fusing) information at various levels of ASD system operation.

Jan 1, 2010

By Yerkezhan Madenova, Kairat Kalmurzayev

This study intends to demonstrate the engineering application of ground penetrating radar (GPR) that would enable site engineers to prevent the high cost of blind drilling. At the tailing dump located in Zhairem Mining and Processing Plant, the challenge of sheet pile driving is encountered due to the indefinite watertight clay layer deposition depth that serves as a protective layer against groundwater contamination. A numerical model of the soil underlying the tailing dump is built using the existing hole data to compare and confirm the existing geological cross sections for three profile lines along the south and southeast parts of the tailing dump. GPR is employed to investigate the subsoil geological structure and detect the watertight clay layer deposition. On the basis of radargrams tied to the existing borehole data in the numerical model, 21 drill hole locations are suggested to assess and confirm the clay layer depth along profile lines at the tailing dump. The drilling results of the suggested holes confirmed the expected depth of the clay layer. It is concluded that GPR is a practical and economic subsurface mapping method that can prevent the high cost of blind digging of the ground and orient the drilling operations effectively.

Jan 12, 2023

By Richard P. Killmeyer, Carl P. Maronde, W. W. Wen, Peter J. Suardini

Under a cost-shared Department of Energy contract, awarded as part of the Coal Preparation Program&apos;s High Efficiency Preparation subprogram, Custom Coals International will be installing and testing a 227 kglhr micronized-magnetite cycloning circuit in PETC&apos;s Coal Preparation Process Research Facility. The project includes the design, construction, testing, and decommissioning of a fully integrated circuit complete with feed coal classification to remove the minus-30-micron material, dense-medium cycloning of the 300 by 30 micron feed coal using micronized magnetite (<10 microns), and medium recovery via drain & rinse screening and various stages and types of magnetic separation. This paper will describe the micronized-magnetite beneficiation technology and the scope of work for this project including an update on the status of the project, the circuit, and the proposed test plan.

Jan 1, 1995

By J. O. McCaldin, P. Duwez

ALLOTROPIC transformations between 1000° and 1900°C have recently been reported for several metallic elements. Since the proposed transformations are based on limited evidence, it was decided to examine the elements in question as well as some refractory metals by thermal analysis with a photoelectric technique similar to that described by Hug-gins, Roll, and Udin.1 In this method, a lead sulphide cell was used to detect thermal radiation from an electric-resistance heated strip specimen. A thermocouple spot welded to the specimen was used to calibrate the temperature of the system under steady temperature conditions, and recording was accomplished with a cathode ray oscilloscope. In the method used by the present authors, the temperature calibration was omitted and the cathode ray oscilloscope was replaced by a recording galvanometer. This technique, in which electric current passing through the specimen heats it, will be referred to henceforth as Method 1. Another arrangement was required for those cases where the specimen could not be formed into a wire or strip suitable for resistance heating. In such cases the specimen was a sintered compact heated by thermal radiation from a hot tungsten strip, Fig. 1. The specimen was insulated from the heating strip with a thin layer of thoria powder or suspended on 0.004 in. tungsten wires. The take-up spring had just sufficient tension to prevent buckling of the heating strip due to thermal expansion. This technique will be called Method 2. Both methods were tested with specimens of iron and titanium and the well known allotropic transformations, a toy and ? to 8 in iron and a to in titanium, were very clearly detected. Fig. 2 shows one of the records obtained for titanium. For this particular experiment, the iodide titanium specimen was a square rod 0.080 in. on an edge and 3 in. long.

Jan 1, 1955

By G. France

The Blair Athol Coal Mine (BAC) is a large open cut operation in the Bowen Basin of Queensland, Australia. Current mine capacity is about 11 million tonnes per annum(Mtpa) of export coal. On-line analysis at BAC consists of two Coalscan 9500s installed directly on the output of the crusher plant and immediately before the product stockpiles, while a third Coalscan 9500 is installed on the transfer conveyor feeding the train loading bin. The two product Coalscans have a dual purpose. The first is to provide real time coal quality data directly back to the mining operations. The second is that of modeling the product stockpile with accurate on-line information. This modeling enables both production and coal quality personnel to accurately examine the coal quality of each stockpile with a degree of resolution which previously had never been achieved.

Jan 1, 1999

By Wilhelm Brandstätter, Johannes Steiner, Alois Triessnig, Christian Redl

"The results of numerical simulations of bubble detachment from an orifice in a horizontal plate submerged in liquid are presented. The bubbles are created by forcing gas through this orifice into stagnant liquid. The simulations are performed with a two-dimensional incompressible Lattice Boltzmann (LB) scheme. In previous works the same problem was investigated by two-phase simulations in which surface tension effects were considered by an interaction potential formulation between the phases. In contrast, in the present work a volume of fluid (VOF) model consisting of a carrier fluid and a passively advected scalar function for the calculation of gravitational and surface tension forces, respectively, is used. The aims of this study are to examine the applicability of the one-phase LB method to the numerical analysis of bubble formation and to verify the theoretical and experimental predictions of the dependencies of the departure diameter on gravitational forces, surface forces and wettability effects. To this purpose the simulations were performed at different values of gravitational acceleration g, surface tension coefficient s and contact angle ß. Nonlinear fits to the data yield functional dependencies which are in good agreement with the predictions. IntroductionBubble formation behavior is an extensively studied subject, especially in chemical engineering, power industries and metallurgical processing. Knowledge of the underlying physics of bubble motion is, for example, required for the design of chemical reaction towers and agitation tanks. Another important application is the argon gas injection through the wall of the tundish nozzle into liquid steel stream to deter clogging with solid inclusions. Argon bubble motion and its effect on flow depends greatly on different parameters, e.g. gas flow rate and size of the bubbles. Thus, if these bubbles are not managed properly, they can become encapsulated upon solidification and result in undesirable impurities in the material [1, 2]."

Jan 1, 2004

By R. W. Watson

This Bureau of Mines report summarizes some recent results on the sensitivity of various experimental explosive systems using ammonium nitrate (AN) as the oxidizing agent. The sensitivity survey included drop-weight and friction testing and sensitivity to initiation by projectile impact and a No.8 blasting cap. It was found that certain types of AN prills can result in cap-sensitive mixtures when combined with No.2 diesel fuel (Fa); prilled AN mixed with nitromethane also result in cap-sensitive mixtures. Mixtures of AN prills and neat 1-and 2-nitropropane were not cap-sensitive, and the use of powdered or grained aluminum in AN-FO did not adversely affect the sensitivity except possibly to increase its sensitivity to friction.

Jan 1, 1974

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations reluted to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 3’% to 1% S and greater than $28.65/t ($26 per st) for removal below 1% sulfur.

Jan 8, 1987

By Haydn H. Murray

In 1967 a large kaolin deposit was discovered on the Jari River, a tributary of the Amazon, in the territory of Amapa in Brazil. The kaolin occurs in the Barreiras Series of Pliocene age and is part of the Belterra Clay. The kaolin was drilled and tested, and today a modern processing plant is producing over 150,000 tons per year of high quality paper coating clay. Some of the problems associated with the mine development, processing, personnel, and marketing of this remote kaolin deposit are discussed. The mineralogy and physical properties of the Jari kaolin deposit are also described.

Jan 1, 1981

By P. -Q. Wu

A modified electrochemical noise (EN) technique has been applied to monitor corrosion wear of TiN-coated ASP23 steel and TiN-coated AISI 316 stainless steel sliding against corundum in 0.5 M H2SO4. Experimental results show that the EN technique can sensitively detect potential and current variations during a corrosion-wear process. Corrosion-wear mechanisms of TiN coatings depend on their substrate properties. If the substrate is passive, such as AISI 316 stainless steel, the potential and current variations reflect the properties of the coating. Depassivation and repassivation alternately take place on the tribo-activated wear area during the steady-state phase. If the substrate is active, such as ASP23 tool steel, the electrochemical noise is dominated by dissolution of the substrate at the pinholes and the hydrogen evolution all over the exposed surface.

Jan 1, 2005

By Jr. Sillers

This is the sixth report of investigations in cooperation with the steel industry to establish the technological acceptability of electrolytic manganese in steelmaking processes. The bulk of the .electrolytic manganese used in these tests was produced by the Bureau Of Mines from domestic ores at its Boulder City, Nev., pilot plant by the process developed by the Bureau. Electrolytic manganese for the first series of tests made in 1940 was supplied by the Electro manganese Corp., Knoxville, Tenn. The first report dealt with the application of electrolytic manganese to the manufacture of stainless.steel;9 the second with tests in acid electric and acid open-hearth low and medium carbon-steel castings; the third with its use in rimmed and? killed low-carbon steels; the fourth with its application to the manufacture of stainless steel as well as the Timken 16-25-6 alloy for gas turbines; and the fifth with tests in acid and basic electric steel foundry practice and basic steel ingot production.

Jan 1, 1948

By J. D. Davis

THIS REPORT gives results of an investi¬gation of the carbonizing properties of coals from Pittsburgh bed, Jamison No. 9 mine, Marion County, W. Va., and from Upper Freeport bed, Bull Run No. 1 mine, Preston County, W. Va. The study included Bureau of Mines-American Gas Association tests at 800° and 900° C. and various chemical and physical tests designed to evaluate the plastic, expanding, and agglutinating properties of coal. A blend of each coal was carbonized in the 500-pound slot oven. The carbonization sample of Pittsburgh coal contained 2.7 percent moisture, 35.8 percent volatile matter, 54.4 percent fixed carbon, 7.1 percent ash, and 0.9 percent sulfur. It contained 60.9 percent fixed carbon on the dry, mineral-matter-free basis and had a heating value of 14,780 B. t. u. per pound on the moist, mineral-matter-free basis. It therefore ranks as high-volatile A bituminous and was blended with low-volatile Pocahontas No. 3 coal. Upper Freeport coal contained 2.8 percent moisture, 27.7 percent volatile matter, 60.9 percent fixed carbon, 8.6 percent ash, and 1.0 percent sulfur, as carbonized. It contained 69.5 percent fixed carbon on the dry, mineral-matter-free basis and therefore ranks as medium-volatile bituminous. It was blended with high-volatile A Pittsburgh coal from Allegheny County Pa.

Jan 1, 1952

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. [Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.]

By R. Quintero

The HYL Direct Reduction Process was the first in the world to operate successfully at industrial scale. The results were so innovative and attractive that other steelmaking companies acquired licenses for the HYL Process. Now in its 40th year of commercial operation, the HYL process has evolved into a modem, highly efficient and economical technology -HYL III. The technology offers high productivity, minimum energy and water consumption, electricity co-generation, raw material flexibility, premium quality DRI/HBI, and is highly versatile for meeting the specific needs of each user. A historical review as well as recent developments and future plans are presented in this paper.

Jan 1, 1998

By David L. Bickel

Stress-relief techniques and instrumentation have been developed through many years of research in the Bureau of Mines and successfully used to determine the in situ state of stress in rock. This report describes the Bureau&apos;s three-component borehole deformation gauge and the drilling equipment and accessories used with it. Operation and calibration procedures for the deformation gauge are discussed in detail, along with site selection and overcoring procedures. Information and references included in this publication provide a guide to the Bureau&apos;s cover-coring method for determining rock stress.

Jan 1, 1985

By R. C. Buehl

A pyrometallurgical process for recovering manganese from open-hearth furnace slags or low-grade manganiferous iron ores is described. The slag or ore is smelted in a blast furnace to produce spiegeleisen; the speigeleisen is then blown with air in a basic converter to give an oxide slag. This slag product contains 60 to 75 percent manganous oxide and may be considered a synthetic manganese ore. In the smelting operations coke rates for five test periods ranged from 3,255 to 4,130 lb per ton of spiegeleisen. The recovery of manganese in the spiegeleisen varied from 60 to 76 percent. Recovery increased to 83 percent when the open-hearth slag feed to the blast furnace was diluted with a high-? grade iron ore sinter to facilitate smelting. In blowing the spiegeleisen a cyclic procedure was developed that gave nearly 90 percent recovery of manganese in the slag product (synthetic ore) yet prevented excessive contamination of the slag by phosphorus and iron. The overall recovery of manganese was about 75 percent when iron ore sinter was used with the open-hearth slag in the smelting step. The metal remaining after oxidizing the manganese from the spiegeleisen contained approximately 3.5 percent phosphorus. It was refined in a basic converter by blowing with air in the presence of lime" A high--grade iron and a basic phosphate slag were produced.

Jan 1, 1965

By V. Bonilla-Sierra, M. Elmouttie, L. Scholtès, F. V. Donzé

In the presence of joint sets sub-parallel to a slope face, the stability of the rock mass is controlled by the shear strength of the joints. On one hand, if the joints are persistent their shear strength can be assessed according to Mohr-Coulomb criterion, assuming appropriate values for the cohesion and the friction angle on the joint surface. On the other hand, if the joints are non-persistent with their continuity being interrupted by the presence of rock bridges, their shear strength will increase considerably. In this latter case, the contribution of the rock bridges to the shear strength of the joint has to be accounted for in order to better assess the stability of the rock mass. A numerical analysis of the progressive failure of a rock slope involving a non-persistent joint has been set up based upon simulations performed using a Discrete Element Method (DEM) algorithm specifically enhanced for the modeling of jointed rock masses. Pre-existing discontinuities are explicitly accounted for in the model by using a modified contact logic that ensures an explicit and constitutive mechanical behavior of the joint planes. In addition, rock bridges can be spatially distributed along these joint planes following a prescribed probabilistic technique. Jennings’ formulation (Jennings, 1970) is considered as one of the first rock slope analysis that evaluates the shear resistance to sliding as a weighted combination of the shear resistance of the intact rock and the joint planes. The validity of this formulation is discussed in the present study. Contrary to the Jennings’ formulation, we show that tensile failure is an important mechanism, particularly as the dip angle of the sliding plane increases.

Jan 1, 2015

By S. J. Schatzel, K. M. Ajayi, Z. Khademian

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine creating safety concerns. To provide recommendations for developing guidelines that ensure a safe co-existence of longwall mining and unconventional shale gas production, this study evaluates the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach using a discrete fracture network (DFN) model. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements. The results show that a decrease in fracture aperture (potentially due to longwall-induced stress in the likely vicinity of the breach location) reduces the potential gas flow to the mine by a significantly higher proportion. A 50% decrease in the aperture of the fracture that directly transports the gas from the casing breach location reduces the gas flow to the mine by over 70%. Similarly, changes in the fracture water saturation level significantly affect the gas flow. In all cases, the potential gas flow to the mine is higher if the casing breach occurs at an increased gas well pressure. These findings provide critical information regarding the impact of each of the parameters associated with gas flow in the event of a shale gas casing breach near a longwall mine and could help towards the development of guidelines to ensure a safe coexistence of both industries.

Mar 2, 2022

By Wayne A. Van Voast

Many coal beds that will be mined in southeastern Montana are aquifers that provide essential local water supplies. Mine cuts along aquifer outcrops create almost imperceptible piezometric changes. Monitoring near such operations at Colstrip has detected almost no water-level declines in observation wells. Mine cuts between outcrops induce rapid storage depletion and associated piezometric depressions. One such cut near Decker induced 1,250 m3/day of flow from storage and created a piezometric depression of 3 meters or more as far as 1,500 meters from the mine. No wells have yet become non-productive but losses of some are inevitable as operations expand. Alternative supplies are available from aquifers stratigraphically below the disturbed materials. Effluents from active mines are chemically similar to other area waters because they are mixtures or ground waters entering the mine cuts. Occasional high concentrations of nitrate do occur, however, as residuals from explosives. Spoils generally consist of confined aquifers of wasted coal and coarse rubble at their bases, overlain by finer-grained sand, silt, and clay. Hydraulic conductivities and storage coefficients are comparable with those of undisturbed confined aquifers. Water quality in mined lands is highly diverse because of diverse spoils lithologies and poorly-established ground-water circulation. Ground water in spoils is more mineralized than in the coal beds and chemically resembles waters from sandstone aquifers. Hydrologic effects of mining will not be catastrophic or widespread but may have local significance. Most notable changes will be in water quality; availability will not be permanently reduced.

Jan 1, 1978