Search Documents

By Henry Louis

THE work performed by the Royal Commission on Mining Subsidence is likely to prove of permanent value, less perhaps for the conclusions it has reached and for the recommendations it has based upon these than for the admirable exposition which it affords of the law concerning mining subsidence and of the legal status of the person who has suffered damage by reason of such subsidence, as also of him whose working has caused the damage. The Commission was appointed by Royal Warrant in the middle of 1925 and delivered its final report in the middle of 1927. The terms of reference to the Commission were as follows: "To consider the operation of the law relating to the support of the surface of the land, and of buildings or works on or under the surface, by underlying or adjacent minerals; to enquire into the extent and gravity of the damage caused by subsidence owing to the extraction of minerals and the incidence of the resulting liability; and to report what steps should be taken, by legislation or otherwise, to remedy, equitably to all persons concerned, any defects or hardships that may be found to arise in existing conditions."

Jan 1, 1929

By S. K. Kawatra, S. J. Ripke, T. C. Eisele

"An estimated 600,000 tons of bentonite clay are used annually in the U. S. as binder for production of iron ore concentrate pellets. Since this is a significant cost item for the plants, and the addition of bentonite to the pellets contributes undesirable silica into the finished pellets, there is considerable incentive for finding methods to reduce bentonite use. One way to reduce bentonite levels is to selectively use those bentonites that are most effective in this application, so that a lower dosage will still produce a sufficiently strong pellet. Unfortunately, there are no satisfactory methods available for accurately predicting which bentonites are actually most effective, short of using them to actually make pellets. One of the popular methods for attempting to evaluate bentonites is the “Plate Water Absorption” (PWA) test. While some plant operators accept the PWA results as indicating the relative quality of bentonites, others disagree and claim that, over a fairly broad range of values, PWA does not correlate with bentonite performance.Since both Ca+2 and Mg+2 ions are known to reduce the swelling and water absorption capacity of bentonite, it was believed that the presence of these ions in plant recycle water could be changing the bentonite performance. Since the standard PWA test uses only distilled water for its measurements, it could not detect these effects. Experiments were therefore carried out on a number of different bentonites using a modified PWA tests, with plant recycle water replacing the distilled water. These experiments showed little effect of the plant water on the PWA value, and chemical analysis of the water showed that the levels of dissolved salts were quite low.Water and accompanying salts were then extracted from a magnetite concentrate filter cake by rinsing with distilled water. Analysis of this water showed an extremely high level of dissolved salts, particularly salts of calcium and magnesium. When concentrations were compared with the recycle water from the plant filters, it was determined that levels of Ca+2 and Mg+2 retained in the filter cake were over 500 times higher than levels in the recycle water. This extreme elevation of soluble salts in the filter cake is believed to be due to adsorption of these ions into the electrical double layer of the magnetite particles."

Jan 1, 2003

By Matthew John M. Krane, Christopher J. Vreeman, J. David Schloz

"A continuum mixture model of the direct chill casting process is used to model the transport phenomena and solidification behavior in the Direct Chill casting of an Al - 6 wt% Cu billet using Wagstaffs AirslipTM process. The model, which includes the transport of free-floating solid particles, can simulate the effect of a grain refiner on macrosegregation and fluid flow. Numerical predictions of sump profiles and composition and temperature fields are presented. Two 45 cm diameter billets were cast under production conditions with and without grain refiner. Temperature and composition measurements and sump profiles are compared to the numerical results. The comparison shows excellent agreement for the grain refined case. It is believed that an incorrect model assumption prevents good agreement in the non-grain refined billet. IntroductionDirect chill casting is a semi-continuous process in which molten aluminum enters the top of a water-cooled mold, is cooled, and forms a solid ingot drawn out below (Figure l(b)). The molten aluminum begins to solidify due to the cooling effect of the mold wall. As the ingot is withdrawn from the bottom of the mold, water jets impinge on the surface, directly cooling the billet and forming a solid layer around a liquid melt, commonly referred to as the sump.A particular defect that occurs in a wide range of casting processes, including the direct chill (DC) casting of aluminum alloys, is macrosegregation, the uncontrolled redistribution of alloying elements on the scale of the ingot during solidification. Macrosegregation in DC cast ingots can produce non-uniform mechanical properties [l], which affects the behavior of the metal during downstream forming and heat treat operations."

Jan 1, 2001

By J. C. Gathje

Newmont acquired the Phoenix Project through the acquisition of Battle Mountain Gold in 2000. Shortly after the acquisition, Newmont Metallurgical Services (NMS) and Nevada Operations began development work on a process to Pressure Oxidize (PDX) precious metal rich copper concentrates from Phoenix using the Lone Tree PDX facilities at Valmy, Nevada. The high precious metals content of the Phoenix concentrate - Au up to -300 g/t and especially Ag, up to -1700 g/t - led Newmont to the development of a High Temperature PDX process that achieves high cyanide leach recovery of Au and Ag, from the PDX solids, without the requirement for a messy and expensive "lime boil" or sulphate destruction process. Base metals content in Phoenix concentrates range from: 15-25 % for Cu, 1-10 % for Zn and 0-2 % for Pb. Excellent solution extraction of Cu and Zn is achieved while Pb is precipitated in the PDX residue. In addition to achieving high Au and Ag recovery this process produces very clean PDX discharge liquors that require minimum effort to remove contaminant metals and PDX solids that have superior settling and filtration characteristics. All of these factors contribute to lower capital and operating costs for the overall process. This paper describes the laboratory and PDX pilot plant developments for this process.

Jan 1, 2004

By Jin-yan TIE, Ke-xin JIAO, Qian Li, Hai-bin ZUO, Jian-Liang Zhang, Meng SHEN

This paper designs three factors such as temperature, pH, conductivity and three levels of orthogonal test. Temperature is a significant factor. However PH and conductivity are not significant through poor analysis. Further research is conducted on the temperature. Temperature stability is 50 . Suitable water velocity is 2.3m/s, which is calculated based on the largest part of the heat flux intensity and the corresponding water temperature should be controlled with 1.5. Meanwhile, water velocity increased has little effect on the heat transfer capabilities.

Jan 1, 2015

By E. Goodwin

"Maclaren Forest Products Inc.Lime is commonly used for the neutralization of acid, and the removal of heavy metals in mine waste waters. However, the precipitation of heavy metals as hydroxides must take place under conditions of controlled pH, to produce minimum concentrations of dissolved metals. An account is presented explaining the concepts applied to lime-treatment processes at Bell Mine during the period of a supernatant discharge to Babine Lake; October 18, 1982to January 25, 1983. IntroductionBell Mine of Maclaren Forest Products Inc., Babine Mining Division, an open-pit copper mine, is located on Newman Peninsula, Babine Lake approximately 65 kilometres northeast of the town of Smithers, British Columbia (Fig. 1).A depressed market for copper metal in 1982 forced a management decision to suspend operations at the mine for an indefinite period from October 3 I, 1982. For some time prior to the mine closing date, mine management was concerned about the increasing level of supernatant in the tailings pond , and its possible effects on the stability of the dam when cycloning of mill tailings ceased. Consideration of these potential hazards led to an application being filed with the Provincial Waste Management for a permit to discharge the excess water to Babine Lake. This large lake, an important link with several significant salmon spawning sites, is a major contributor to the British Columbia commercial fishing industry. Jurisdiction for the environmental affairs in the area is shared by the Department of Fisheries and Oceans, the Environmental Protection Service, and the Provincial Waste Management Branch. These agencies were directly concerned in the formulation of discharge permit following joint consultation, and exchange of information with the company on environmental concerns. An approval was finally granted to discharge approximately 1,000,000 cubic metres of supernatant from the tailings impoundment at Bell Mine into Hagan Arm, Babine Lake from October 18, 1982 with a daily discharge not to exceed 9000 cubic metres. Provisions were made that a particular discharge procedure be followed, and that the company would be responsible for setting up a sampling and monitoring program to safeguard the quality of the effluent."

Jan 1, 1986

By Osamu Taki

The innovative Soil-Cement Mixed Wall Technique emerged in Japan and obtained recognition in the engineering and construction communities in the 1980's. This technique was introduced to the United States in 1986. It was accepted as the most credible construction technique by the U.S. Bureau of Reclamation for ground stabilization and cutoff wall work in the Jackson Lake Dam Project, Wyoming in 1987 and 1988. It was also accepted as a remediation technique by U.S. EPA for a Superfund Innovative Technology Evaluation (SITE) demonstration on in-situ solidification/ stabilization. The Soil-Cement Mixed Wall Technique consists of mixing in-place soils with cement grout or other reagent slurries using multiple axis augers and mixing paddles to construct overlapped soil-cement columns. The overlapped column panel is then extended to form an underground continuous soil-cement wall for use as a cutoff wall or a structural diaphragm wall for groundwater control and excavation support. By arranging the column panels in various configurations, the technique becomes a versatile tool for stabilization of soft or liquefiable soils.

Jan 1, 1990

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved.

Jan 1, 1979

By M. F. Goudge

BRUCITE associated with highly metamorphosed Precambrian limestone was discovered in the vicinity of Rutherglen in northern Ontario by the writer during field work on the limestones of that district in 1937, and later was identified in similar limestone at Bryson and Wakefield, Quebec. The brucite occurs as granules disseminated through the limestone (Figure 1) and comprises from 20 to 35 per cent of the rock. Such rocks may be referred to as predazzites or pencatites, depending on the proportions of the constituent minerals. In this paper, however, the general term brucitic limestone is used to designate limestone containing brucite. In none of the deposits does the magnesia content of the rock approach that of magnesite, and in the deposits near Bryson and Wakefield the magnesia content is only that of dolomite. Therefore, without some method of concentrating the brucite, the deposits would be of little or no more value as a source of magnesia than is ordinary pure dolomite, which is abundant in many parts of Canada. Investigations in the laboratories of the Bureau of Mines have, however, resulted in the development of a method whereby, from certain of the deposits, pure calcined brucite, or magnesia, in granular form can be obtained, apparently at a cost that will enable it to compete in eastern Canada with imported magnesia. The granular magnesia so obtained appears to be highly suitable for use in basic refractories, for making magnesium metal, and for various other purposes for which magnesia is commonly used. Prospecting in the neighbourhoods of the original discoveries has resulted in a number of other deposits being found in each of the three areas, and there is now apparently available s1.dficient brucitic limestone of a grade that will lend itself to commercial exploitation to supply for many years a large part of the present and prospective Canadian market for magnesia and its products. Furthermore, it is expected that additional deposits will be discovered as prospectors and others become more familiar with the appearance of brucitic limestone.

Jan 1, 1940

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselrnan Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo.

Jan 1, 1949

By S Grobler, T Fares

Understanding the real utilisation of the available volumetric capacity of a conveyor is key to unlocking latent capacity or ‘debottlenecking’ existing plant. Conveyors are typically designed on the basis of conservative density and ore surcharge angle specifications, and consequently there is often latent volumetric capacity available.Laser scanning measurements of conveyor ore profiles has been undertaken on iron ore conveyors to gain an understanding of the actual surcharge angle and the available edge clearances. Iron ore producers seeking to extract maximum production from their assets have used these measurements to debottleneck existing plant and to revise the design criteria for future plant. The benefit is that latent capacity of existing plant can be unlocked and smaller and cheaper conveyors can be designed for future plant, maximising the return on capital. This paper describes the measurements and results.CITATION:Fares, T and Grobler, S, 2015. Laser scanning of conveyor ore profiles, in Proceedings Iron Ore 2015, pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Jack I. Paige

The devitrification of lithium silicate glasses was studied to determine the effect of annealing temperature, composition, and additives on nucleation and crystallization. High-purity glasses, prepared from reagent-grade chemicals, had close to optical quality when prepared by a vacuum induction melting method developed during this research, The progress of devitrification was traced by differential thermal analysis and thermal expansion for those lithium metasilicate-silica compositions containing 80 to 90 percent silica. Microscopic studies of glasses partially devitrified at various temperatures and annealing times indicated that the primary initial mode of formation of individual crystals ,vas from densely crystalline zones that filled in as crystallization advanced Of the additives tested, calcium, potassium, and sodium helped promote devitrification with the least cracking or surface deformation. Tin oxide was most effective in reducing volume contrast ion during devitrification, but was not ClS effective in preventing cracking as calcium or potassium additions.

Jan 1, 1965

By Bert S. Hall

"The purpose of this paper is to review the evidence at hand concerning the earliest centuries of cast iron in Europe, from roughly 1400 A.D. until the second half of the sixteenth century. For the most part it is concerned with the relationship between two technologies which emerged first in China and then later appear in Western lands, gunpowder weapons and iron founding. We should not assume, as I hope to show later in this discussion, that weapons constituted the only product for which the iron founder had any market, but it is clearly true that attempts to produce weapons constituted the most severe technical challenge for the early founder. Firearms appear for the first time in Europe in the 1320s and develop into significant weapons on the field of battle by the end of the century. Theirs is a complex history, subject neither to easy summary treatment nor to simplified models of development. I hope to be able, through the analysis of the evidence concerning cast iron, to show that one important strand in the fabric of gunpowder's history concerns the materials from which cannon could be made. This question is subject to a number of shades of meaning, because ""cannon"" can be made for many purposes under a profusion of different names, and under sharply varying conditions of use. As a result, the question of materials is frequently really a question of competing materials, and involves a complex set of factors, of which production costs and the ultimate safety of the user seem the most important. Judged in this manner cast iron was an important but unsatisfactory metal for weapons purposes until 1543, at which time English founders learned to make iron muzzle-loading cannon which could rival bronze ordnance in most important performance criteria, but which cost much less to produce. With that event, the history of cast iron and the history of weapons entered into the close relationship that persisted until the advent of rifled artillery made of steel in the middle of the nineteenth century."

Jan 1, 1999

By G. K. Derby

Paper presents project results investigating current techniques for dragline wire rope removal and the development of less hazardous means of performing the task. The cannon is the most prevalent method used in American surface mines. A cannon test program was conducted that used 40-and 50-grain primer cord to establish force produced using a 56-pound projectile. Socketlwedges were separated to establish separation force data. Two alternative removal methods, pendulum ram and portable hydraulic pusher, were developed and tested. Both provide sufficient force to effect separations under normal conditions on draglines with up to 78- cubic yard buckets.

Jan 1, 1984

"A cationic surfactant, tetradecyl tributyl phosphonium chloride (TTPC), was first used as a collector. Flotation characteristics of muscovite using TTPC have been investigated through flotation tests. And dodecyl trimethyl ammonium chloride (DTAC) was tested for comparison. Their adsorption mechanisms on muscovite surface were clarified using zeta potential measurement, DFT calculation and molecular dynamics (MD). The flotation results indicate that the recovery of muscovite decreases when the pH increases in the presence of surfactants. When a maximum of recovery was reached, the dosage of TTPC was 2×10-5mol/L which was half of that of DTAC. Zeta potential measurements confirm that the TTPC displays a stronger collecting power than DTAC and is a superior collector for the muscovite flotation. DFT calculation and MD simulations show that TTPC interacts with the muscovite mainly through electrostatic attraction and hydrogen-bonding. The conclusions drawn from purely theoretical computations matched remarkably well with the experimental results. Keywords: Quaternary phosphonium salts; Flotation collectors; Flotation INTRODUCTION Muscovite mica is widespread in igneous, sedimentary and metamorphic rocks. It has the general composition KAl2(AlSi3O10)(OH)2. Muscovite mica exhibits perfect cleavage along the (001) plane, which exposes interlayer potassium ions[1-3]. In aqueous suspensions, the potassium ions readily enter into solution, leading to the development of a net negative charge on the (001) plane[4-6]. The surface of the muscovite mica is negatively charged at all pH > 1[7]. Due to the negative charge surface over the whole pH range of 2–12, the muscovite mica would not be expected to respond to anionic collectors in the absence of an activator. Conversely, the mineral is readily recovered using cationic collectors. However, until now, various amines and their derivatives (with N atoms as the center) are still the only available cationic collectors which still had their shortcomings such as weak selectivity, low flotation speed. Since few types of cationic collectors could be used, in some sense, the limitations of collectors are increasing significantly and the cationic flotation is facing more and more challenges. Quaternary phosphonium salts, as novel cationic surfactants, are widely used in antimicrobial, catalysis and surface modification field due to their biological activities, hydrogen bonding capability, stability and superior group electrical property[8-10]. There are a number of processes where quaternary phosphonium salt surfactants have shown better properties than quaternary ammonium salts and amines. Although the adsorption of quaternary phosphonium salt surfactants at the bacterium–liquid interface has been studied thoroughly, the case of adsorption in mineral surface has not been investigated thus far."

Jan 1, 2016

Classification within the Inferred Resource category is based on geological judgement and the balance of extrapolation versus interpolation that the Competent Person is prepared to accept. These resources are typically drilled at spacings well in excess of the geostatistical range and at a density that is non-uniform. In many cases, a substantial proportion of the available data will be historical, and should be considered with more recent data sources. The provision of a robust geological model will increase the confidence in any resource estimate, and should be viewed as a critical component. The definition of Inferred Resources is of great importance to vein gold projects, since Indicated and Measured Resources generally require costly underground development for delineation. Indeed, many gold vein operations possess substantial quantities of Inferred Resources (>75 per cent) in their resource inventory both at project start-up and during production. This contribution explores a number of the key issues when using the Inferred Resource category and presents four recent case studies.

Jan 1, 2006

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By Michael P. Hardy

The report described improvements and applications of the Hybrid Computer facility. Improvements implemented under U.S.B.M. Contract H0252035 included expansion of the capability to model nonlinear seam behavior, installation of a color video output display monitor, and further development of software capabilities. To demonstrate the capability of the system, firstly, the influence of nonlinear seam behavior response to the occurrence of coal mine bumps was fully investigated and secondly, the effect of improper mining sequence on bump occurrence was demonstrated. In addition, the system was applied to the analysis of a series of practical coal mine problems. Mines in three coal seams were analysed to investigate the parameters which contribute to the occurrence of coal mine bumps.

Jan 1, 1977

By H Asche

The Melbourne Metro project has evolved from the Victorian Transport Plan. MM1 is the second major phase of the proposed separation of Melbourne’s radial railway system, creating a line that will operate independently across the metropolitan region. The central section will run beneath the inner suburbs and the central city. The initial project comprises nearly 8 km of twin bore tunnels, three cavern stations and two cut and cover stations, as well as a dive structure and connections with the existing rail system. This paper describes the development of the geological model, a modification of the rock mass classification system derived during the EastLink project and the influence of the geology on the design of the tunnels and stations for the Department of Transport’s business case.The majority of the tunnelling will be in the siltstone and sandstone bedrock. This material has been extensively folded, sheared and intersected by igneous intrusions. A revised rock mass classification system has been developed for the Melbourne Formation to assist in identifying the important engineering properties of the rock and to rationalise the support types required.The Metro’s tunnel alignment crosses the Yarra Delta deposits in the lower reaches of the Moonee Ponds Creek and again at the Yarra itself near Princes Bridge. These deposits vary in extent and thickness over very short distances. The investigation of these materials has been carried out using conventional drilling techniques in conjunction with sonic drilling methods.Over the central section of the Metro, the positions of the new station are determined largely by transport planning requirements and urban development opportunities. However, the stations, and the tunnels, have been the subject of studies, optimising exercises, and selection processes to arrive at the concept design. This paper describes the influence of the varied geology on the development of the design, and the identification and management of the risks in tunnelling under the centre of Melbourne.

Mar 8, 2011

By Joseph M. Pugliese

This work was done by the Bureau of Mines to provide quarry operators with an uncomplicated, first-approximation method for designing blast patterns, considering geologic structure, and to show the valid use of the technique by comparing drill and blast pattern dimensions used in the quarry with those determined by the presented method. The author visited 12 limestone and dolomite quarries in Ohio (Adam, Crawford, and Highland Counties), Wisconsin (Milwaukee, Racine, and Waukesha Counties), and Minnesota (Fillmore, Olmsted, and Wabasha Counties); observed the blasting practices; studied the major geologic features; and after discussion with the quarry managers, foremen, and blasters, compared the quarry blasting patterns with those as calculated by the empirical formulas (after R. L. Ash), with geologic structural considerations. When geologic structure such as bedding, jointing, folding, and caves, as well as explosive properties and field performance characteristics are accounted for in a manner suggested by the research, the presented empirical formulas may be used as a good first approximation. The included steps in planning a blast design and generalized blast patterns should be of help to the quarry operator. Design changes are recommended for those quarries where problems are occurring.

Jan 1, 1972