Search Documents

By W. R. SHAHAN, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation on the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). 

By F. Ajersch, P: Tsantrizos, K: Shanker

"TiN films have been deposited on various substrates by a novel reactive plasma technology. In this process, a nitrogen source (NH3 or N2) and TiCl4 are reacted in the jet of a plasma torch, and are deposited onto a substrate forming TiN films at a high growth rate ( > 2µm/min). It was found that the process parameters strongly affect the microstructure, thickness, density, and growth rate of the TiN films. These parameters include source of nitrogen (NH3 or N2, N/Ti ratio, temperature of substrate, and spray distance. In general, it was found that thick and dense coatings were deposited when the N:Ti ratio was kept low, and the substrate temperature was high. Also, for the series of conditions investigated, NH3 was found to give much better results than N2•. The limitations and advantages of this technique are also discussed in this paper.IntroductionTiN is an extremely hard material and is used in many wear applications, particularly as a protective coating on cutting tools to extend their Iife(1.2). Owing to its excellent chemical stability, TiN is also frequently used as a diffusion barrier in the electronics industry for sub-micron Al/TiN/Si ohmic contact systems (3) or as a coating on high-temperature resistant alloys in gas turbine applications (4), based on its good resistance to oxidation. Other applications include decorative coatings in the jewelry industry, and specialized applications such as solar energy absorbers and transparent heat mirrors(5).TiN films can be deposited/formed using various techniques. The main techniques of deposition are CVD (Chemical Vapour Deposition) and PVD (Physical Vapour Deposition). Each of these techniques can have many variations in equipment characteristics, reactants as well as a range of process parameters (pressure and temperature). In the CVD process, TiN is generally deposited onto a heated substrate where a chemical reaction takes place. The reaction can be one of reduction(6) (e.g.: TiCI4 + 0.5N2 + 2H2 --> TiN + 4HCI), of thermal decomposition(7) (e.g. decomposition of titanium dialkylamide), or of displacement (e.g. TiCI4 + NH3 --> TiN + 3HCI + 0.5CI2)' The displacement and reduction reactions are the most common."

Jan 1, 1994

By Parker C. J, Mikula P. A

The excavation for the Sydney Opera House Parking Station comprises a large donut shaped underground cavern with a central sandstone pillar. The maximum effective roof span is about 19 m and the rock cover is between 7 m and 8 m. Permanent support for the roof and the various services tunnels consists of a combination of tensioned anchors, and untensioned dowels, and mesh with shortcrete and fibrecrete as the final lining. Steel sets were installed at main intersections.Fundamental to the design philosophy for excavation of these spans at such shallow rock cover was the use of monitoring to check on the adequacy of the installed support. Prior to excavation, extensometers, inclinometers, piezometers and surface settlement survey stations were installed. Underground survey stations, anchor load cells and shotcrete pressure cells were installed as excavation proceeded. Excavation commenced at the crown using an initial heading and three widening stages. Geological mapping during excavation confirmed borehole expectations, namely sandstone beds 1 to 4 m thick interbedded with thin shale units. Bedding plane contacts varied over short distances from tight partings to thick brecciated seams. Jointing was subvertical and joints tended to be bed-limited.

Jan 1, 1993

By P. Braga, A. Chaves, S. França, A. Luz

"In Brazil, there are no official reserves of molybdenum, and the unofficial reserves are modest. Therefore, the molybdenum ore (molybdenite) produced as a co-product or by-product of emerald mining in the region of Campo Formoso, BA, has arisen as the only economic option. The flotation process is commonly used in Brazil for the recovery of molybdenite from emerald mining tailings, but it produces low-content molybdenite concentrates, thereby resulting in a product with low economic value. The molybdenite concentrate produced in Campo Formoso contains 83.5% MoS2 (50% Mo), which is less than the international standard product that contains > 90% MoS2 (54% Mo).This low value is due to the presence of talc, which is a naturally hydrophobic mineral that is also floated with the molybdenite during the flotation process. Separability studies were done in a Partridge-Smith cell using dextrin and quebracho as a molybdenite depressor in solution at different concentrations and pH values to produce a technical-grade concentrate (i.e., 90% MoS2). These basic studies were accompanied by measurements of the zeta potential and contact angle, which was determined by the capillary rise method. The results of these floatability studies were used in bench flotation tests, which were performed in a Denver laboratory flotation cell. A molybdenite concentrate of 93.4% MoS2 was obtained when dextrin was used at a concentration of 100 g/t."

Jan 1, 2014

By Brian Penney

"The Iron Ore Company of Canada (IOCC} has mined and processed an iron deposit in Western Labrador along the Labrador-Quebec border since the early 1960' s. Current capacity is approximately 19 million tonnes of concentrate, 70% of which is converted to pellets at these facilities.The ore deposits are located in hills rising 150 to 300 meters above the adjacent lakes, and most of them are covered by very little overburden. The iron minerals are mainly specular hematite and magnetite hosted in a quartz formation. Crude ore averages 40% Fe that is concentrated to 65.5% Fe. IOCC is an extensive operation extending from Labrador City NF to Sept-Iles Quebec. It consists of open pit mining, concentrating, pelletizing, railway, and dock loading facilities.The Concentrator liberates iron from the silica by crushing and grinding the ore to -14 mesh (-1190 microns}. Ground ore is concentrated in spirals and filtered for transportation. Spiral tailings are treated in a Magnetic Recovery Plant (Mag Plant} that recovers lost magnetite. Mag Plant tailings are treated in a Hematite Spiral Plant (Hem Plant} that scavenges fine iron remaining in this stream.This report deals with ongoing iron recovery initiatives within the ConcentratorIron Losses in the ConcentratorIron recovery at IOCC is approximately 70.5%. This compares with recoveries that range from 65% to 86% for other iron mines in our area. Other world large iron ore producers dig and ship concentrate quality ore directly out of the ground and have an effective recovery of 100%. With increasing costs for labour, equipment, and supplies an increase in iron recovery is required to keep the operation viable.More than 90% of our iron concentrate is produced by gravity separation using spirals. The physical characteristics of the iron minerals that most effect recovery are mineral grain size and degree of liberation. We divide ground ore into three size categories -coarse, intermediate, and fines. A brief description of each size fraction follows:"

Jan 1, 1996

By C. Swart

Automation technologies are increasingly adopted in different mines world-wide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHDs at Noranda?s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHDs and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda?s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Jan 1, 2002

By J. Helton, J. L. Bellanca, M. McNinch, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Accident data indicates that mobile haulage poses a significant pinning, crushing, and striking risk. Proximity detection systems (PDSs) have the potential to protect mineworkers from these risks. However, unintended consequences of mobile PDSs can undermine the safety benefit they provide. Soliciting iterative user input can improve the design process. Users help provide a critical understanding of how mobile PDSs may hinder normal operation and endanger mineworkers. Researchers explored users’ perspectives by conducting interviews with mineworkers from seven mines that have installed mobile PDSs on some of their haulage equipment. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance, and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure, and risk. Mineworkers also suggested that improved task compatibility, training, logistics, and PDS performance might help address some of these identified issues. This paper also gives additional insights into mobile PDS design and implementation. INTRODUCTION Pinning, crushing, and striking accidents are a large problem in underground coal mines, especially for mobile haulage. Between 1984 and 2014 there were 179 non-fatal and 42 fatal pinning, crushing, and striking accidents involving mobile haulage vehicles, including coal hauling machines and scoops [1]. Proximity detection systems (PDSs)—automated systems that decelerate and stop a vehicle in order to prevent a collision—have the potential to protect mineworkers in these situations. In fact, PDSs are now required on all place change continuous mining machines as of March 16, 2018, as a result of the final rule published in January 2015 (30 CFR 75.1732) [2]. To address mobile haulage, later in 2015 the Mine Safety and Health Administration (MSHA) also proposed a new rule that would require PDSs on mobile haulage vehicles [3]. Though there has been no additional actions related to the proposed rule and it is not currently required, mobile PDS can still help to save lives. MSHA estimates that the adoption of mobile PDSs could prevent approximately 70 injuries and 15 fatalities over the next 10 years [4]. As of June 2015, the underground coal industry had already equipped 155 of the 2,116 mobile haulage vehicles in use [1]. In order to capitalize on the projected safety gains afforded by PDSs, it is important that the systems are designed and implemented effectively. Along with others, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been exploring PDSs for more than two decades [5-7]. Throughout this time, NIOSH has also held several stakeholder meetings (2010, 2014, 2016, and 2017) in order to disseminate information and provide an opportunity to discuss on ongoing issues and concerns. Despite some progress, human factors remain a key concern. Previous research examined mineworkers’ attitudes towards PDSs on continuous mining machines [8] as well as how continuous miner operators’ perceptions of risk have changed as a result of PDSs [7]. However, stakeholders have still expressed a need to better understand how mobile PDSs affect the mining process, the mineworker, and whether and how they may present previously unidentified risks.

Jan 1, 2019

By A. Navarra, F. Mucciardi, H. Marambio, R. Parra, F. Oyarzún

"Discrete event simulation (DES) is an appropriate framework for the plant-wide analysis of copper smelters. These smelters apply a common set of chemical reactions: copper-iron sulfides are blasted with oxygen-enriched air, sending the iron into a slag phase and the sulfur into the offgas. Moreover, conventional copper smelters exhibit similar operational dynamics: a smelting furnace operates continually, feeding into an alternating set of converters that produce batches of blister copper. The thermochemical and operational commonalities of copper smelters are integrated within the DES framework. This serves as a common basis to begin evaluating the system dynamics of individual smelters. For complex problems, the simulation framework should be developed in phases, incorporating feedback from different personnel who have complementary perspectives. Sample computations are provided in this paper based on the Hernán Videla Lira smelter, whose production is constrained by meteorological conditions. IntroductionWorld copper production is approximately 18.5 million t/y (Brininstool, 2015), worth $80 billion a year. Out of this total, 75 percent comes from the pyrometallurgical processing of sulfide minerals (Fig. 1), which occurs in copper smelters. The remaining 25 percent is from the hydrometallurgical treatment of oxides and complex ores (Rotuska and Chmielewski, 2008), which uses solvent extraction and electrowinning.The current paper describes the pyrometallurgical processing, recognizing that the underlying thermodynamics and kinetics are well known (Degterov and Pelton, 1999), with the notable exception of minor element transport, such as arsenic (As), antimony (Sb), bismuth (Bi), silver (Ag), gold (Au). The latter is an ongoing area of research, as smelters are faced with increasingly complex ores (Devia, Wilkomirsky and Parra, 2012; Swinbourne and Kho, 2012). This paper focuses on the system dynamics of copper smelter operations, which has received considerably less attention than the chemical thermodynamics and kinetics.Smelter engineers and managers may contribute to the sustainability of their plant by improving their understanding of operational system dynamics. Indeed, we have prompted smelter improvement projects (Navarra, 2016; Navarra et al., 2016; Navarra and Mendoza, 2013) simply by adapting methodologies that are commonly used in other sectors. These previous works incorporate principles from computer-integrated manufacturing (Groover, 2000) and theory of constraints (Dettmer, 2007), featuring the use of discrete event simulation (DES)."

Jan 1, 2017

By P. Aguirre

Recovery of zinc, copper and nickel from electroplating waste solutions was achieved 'by using a Pulsated Percolated Porous Electrode "3PE" reactor on a pilot plant scale. Intensity - potential curves were used to study the possibility of metal removal and to define the working potential range. The present study describes the use of the 3PE reactors in several electroplating industrial units for the decontamination of their effluents. These effluents were issued from different industrial solutions such as cyanide, sulfate, chloride and Watts baths. Using the stripping curves, deposition rates and electrical efficiencies were determined as function of the metal concentrations in these effluents. Their decontamination could be achieved to the level of few ppm of metals with reasonable current efficiencies. The recovery rates of zinc and copper were about 93 and 99 %, respectively. The. treated effluents contained less than 7 and 1 % of the initial contents of Zn and Cu, respec¬tively. This process allows the recycling of the recovered metals and leads to water saving.

Feb 13, 2014

By AIME AIME

THE meeting" of the Rare Minerals and Metals Committee was held Monday afternoon, Feb. 17; Donald M. Lidclell, chairman, presiding. The first paper (T. P. 279), "Progress in the Use of Tantalum," by George W. Sears, was read by Mr. Smyth. Dr. Sears' paper contains an interesting summary of the uses, alloys and ores of tantalum and a resume of present method of reduction. The uses of tantalum is based on its extreme rise to the reaction of even the strong mineral acids, its great avidity for the common gases and its capacity for transforming alternating to direct current. Tantalum, as an alloy material, has received considerable study and many alloys have been reported. Among them three types appear to .be most prominent, alloys of high melting point, hard alloys and acid rising alloys. As the estimated quantity of tantalum in the earth's crust is less than that of gold, it must be looked upon as n rare metal. Australia is the greatest producer and the Black Hills of South Dakota produce minor amounts. As the one type of mineral available contains both tantalum and columbium, the extracting and metallurgy of tantalum are difficult chemical processes. Greater simplicity in this and the development of a market for columbium would undoubtedly be of great benefit to the tantalum industry, andl make for a greater use of tantalum produced.

Jan 1, 1930

By Thomas Schwind, Benedikt Grau, Angelos Gakis

"In Crossrail’s Farringdon station, compensation grouting was successfully utilized to mitigate the surface settlements induced by the tunneling works. The main focus of this study was the platform tunnels, which were approximately 300m long each and were enlarged to platform size using sequential excavation method (SEM) from the existing TBM running tunnels, initially supported using sprayed concrete linings. The rear grouting injections were carried out at a typical distance of minimum 5m above the completed, fully strengthened shotcrete lining hence inducing some additional stresses. In-tunnel monitoring using surveying targets was performed systematically to ensure that no excessive distortion of the initial shotcrete lining occurred. 3D finite element analyses were utilized to back calculate the actual “effective” pressure that was imposed on the completed shotcrete rings against the additional measured in-tunnel displacements due to the compensation grouting episodes. Additionally an assessment of the theoretical, “maximum” allowable grouting pressures that would lead to overstressing of the lining is presented. INTRODUCTION As part of the back analysis performed for the SEM tunnels in Farringdon station, an investigation of the effect of compensation grouting on the two constructed platform tunnels was undertaken. The platform tunnels were 10.6m high by 11.4m wide and approximately 300m long each. They were enlarged to their final shape from the existing TBM tunnels using SCL methods. This study utilized 2D and 3D finite element (FE) analyses in order to back calculate the observed tunnel crown displacement, assessing the equivalent grouting pressures during the rear injection episodes of the concurrent grouting operations. The results provide a useful reference for the order of magnitude of the grouting pressure load cases that can be applied in the numerical simulation of similar cases. Part of the results presented in this paper, were derived by the second author as part of his Master of Science thesis in Technical University of Graz."

Jan 1, 2016

By A. E. Halim, J. F. Brune

Debate continues over whether barricading in refuge chambers is a good strategy to survive entrapment emergencies in underground coal mines, in particular fires and explosions. Unlike U.S. coal mines, Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes the merits and problems of using refuge chambers or self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. We found that using refuge chambers may not be the best strategy during extensive fires or when multiple explosions occur. In these situations, mine rescuers are unlikely to be able to extract miners who are sheltered in chambers and, conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as the level 1 emergency exercises required in Queensland, Australia. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By M. Deutsch, E. González, M. Williams

"Uncertainty exists in ultimate-pit limits due to geologic variation and unpredictable economic landscapes. In this work, we show how this uncertainty affects the ultimate pit and how it can be analyzed to improve the mine planning process. A stochastic framework using geostatistical simulation and parametric analysis was used to model the effects of geologic and economic variations on ultimate-pit limits and overall project economics. This analysis was made possible by a new pit optimization implementation that can be automated and set up to calculate ultimate pits for hundreds of different scenarios in a matter of hours. Quantifying ultimate-pit uncertainty early in the mine planning process allows mining engineers to make informed decisions regarding infrastructure placement and to mitigate the possibility of incurring substantial costs to relocate critical mine facilities. Resumen ¦ Existen dudas sobre los límites del pit final por causa de la variación geológica y lo impredecible de los paisajes económicos. En este trabajo les mostramos como esta incertidumbre afecta el pit final y como puede ser analizada para mejorar el proceso de planificación de la mina. Se usó un marco estocástico con simulación geoestadística de análisis paramétrico con el fin de poder hace la modelación de los efectos de las variaciones geológicas y económicas en los límites de pit finales y proyectos económicos en general. Este análisis fue posible gracias a una nueva implementación de optimización de pits que puede ser automatizada y configurada para calcular pits finales para cientos de escenarios diferentes en cuestión de horas. La cuantificación temprana de la falta de certeza en pits finales durante el proceso de planificación permite a los ingenieros de minas tomar decisiones informadas en lo que respecta a la ubicación de infraestructura y en la mitigación de posibles costos sustanciales por causa de la reubicación de instalaciones clave de la mina."

Jan 1, 2015

By F. J. Gallagher

The purpose of this circular is to present information on the construction and use of reinforced rubber-jacketed tubing and insulating air-line couplings in coal mines where Airdox is used for breaking coal in order to eliminate, insofar as possible, arcing at the face between Airdox tubing and the track or other face equipment.

Sep 1, 1949

By G. J. Joy, J. P. Rider

Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 30 m/min (100 fpm). This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the U.S. National Institute for Occupational Safety and Health (NIOSH) is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research (OMSHR) Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities — 152, 213 and 274 m/min (500, 700 and 900 fpm)— and at water pressures of 689, 1,034 and 1,379 kPa (100, 150 and 200 psi). Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Average reduction efficiencies of at least 90 percent were seen at the three sampling locations closest to the shearer for all three manifold systems at nozzle spray pressures greater than 689 kPa (100 psi). Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer, a spray manifold was fabricated and evaluated at an underground operation.

Jan 1, 2016

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 µ m fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 µ m. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1993

By Richard E. J. Putman

THE MINERALS INDUSTRY has always been a heavy user of energy in most of its unit operations: power in the mining, comminution, flotation and electro-winning processes; fuel in its smelting and other metallurgical processes; and, of course, fuel in the on-site generation of power and steam. Many of the techniques for using computers to perform energy management and conservation tasks have been known for some time, but they have not been widely implemented because the return on investment has hitherto been insufficient. Recent trends, however, have not only caused the dollar return to rise due to higher purchased energy costs, but the cost of the investment to fall. One trend has been the generally lower cost of computer control systems themselves, due to vendors having adopted the newer, lower-cost and more reliable electronic component technologies now becoming universally available. The second trend is the development of low-cost, but high-speed, remote multiplexing devices, which have reduced considerably the expense of bringing data from points scattered over a wide area, which is typically the case when applying energy management systems to a minerals processing plant. By taking advantage of these and related developments, computer control systems can now have a rewarding impact on plant energy management and conservation practices, and recent advances in application technology have opened up new and additional opportunities for energy cost reduction and control.

Jan 1, 1978

By M. Mirnezami, J. A. Finch

The McGill component of the consortium contributed detailed examination of the electrokinetic properties of the constituent minerals, primarily pentlandite and serpentine. Mineral specimens were derived from an ore sample; mineralogical examination showed the serpentine was predominantly clinochrysotile, a fibrous mineral responsible for much of the flotation separation problem. The study included design of a novel sedimentation potential measuring device to classify the surface charge of the ore and electrophoresis measurements on single and mixed minerals which progressively approached flotation conditions. The sedimentation potential measurements provided a general association between surface charge and the visual state of aggregation as a function of pH. The electrophoresis experiments started with single minerals in a background of indifferent electrolyte and progressed to mixed minerals in a background of supernatant derived from an ore sample. The single mineral tests supported the suspected electrostatic interaction, i.e., hetero-coagulation, at flotation pH 9-10. The mixed mineral tests demonstrated this interaction and also revealed hetero-coagulation with Mg(OH)2 precipitates, derived from the supernatant. This interpretation was confirmed by optical and electron beam imaging. A series of agents, CMC, polyphosphate, soda ash, EDTA, were examined to disperse the system. To accommodate the small mass of single mineral available a novel turbidity measurement using a UV/Vis spectrophotometer was introduced. Selected conditions were used in contact angle and small-scale flotation tests.

Jan 1, 2011

By Adam J. Gesing

Eddy current separators are increasingly used by the auto shredder operators to produce higher grade of nonferrous metal concentrate for recycling. While this increases the unit price of the concentrate, metal losses through inefficient metal recovery quickly offset the price differential. We show how to optimize the eddy current separation system at the shredder to maximize mate- rial throughput, nonferrous metal recovery and grade of the nonferrous metal concentrate.

Jan 1, 1998

By John L. Mero

"The ocean has served humanity as a source of raw materials for thousands of years, but only on a minimal scale relative to its potential. Exploration programs have shown the ocean to contain a large number of mineral deposits of great extent and attractive grade. Recent research has indicated that a number of these deposits can be economically exploited with present-day technology and that the cost of winning many industrially important minerals from the oceanic deposits is potentially much less than that of winning similar minerals from land deposits. Although the finding of mineral deposits in the sea is a relatively simple matter at the present time, the exploitation of many of these deposits has lagged due to the lack of the availability of specific mining techniques for the individual deposits. Within the past two years, however, several developments have taken place in the design and testing of ocean mining systems in depths of water as great as 12,000 feet which indicate that the problem of mining in the ocean may soon be solved.Within the next decade, the ocean should prove to be a major source of many minerals for society and should come to dominate as a source of such metals as copper, nickel, cobalt, manganese, etc. Within a few years of the initiation of the mining of the deep-sea metalliferous nodules, land sources of such metals as nickel, cobalt, copper, manganese, etc. will be seriously affected and it is conceivable that the present structure of the world mining industry will undergo a substantial change in character."

Jan 1, 1972