Search Documents

By Hebi Yin

A coupled cellular automaton (CA) - finite element (FE) model was developed to calculate the growth of dendrites during the solidification of cubic and hexagonal metals. The model solves the conservation equations of mass, energy and solutes in order to calculate the temperature field, solute concentration and the growth morphology of dendrites, including the grain structure and the dendritic microstructure. Validation of the model was performed by comparing the simulation results with calculation results from previously published works, showing qualitatively good agreement in the dendritic morphology. Application to magnesium alloy AZ91 illustrates the difficulty of modeling dendrite growth in hexagonal systems, observed as deviations in growth direction caused by mesh-induced anisotropy. The model was applied to the simulation of small specimens with single- and multiple- equiaxed grain growths and columnar grain growth in directional solidification. The influence of cooling rate and some kinetics parameters on the grain morphology are also discussed.

Jan 1, 2009

By Y. Champoux, N. Atalla, R. Oddo, C. Lesage

"Percussion drills are the source of the most serious noise problems in mining activities, due to their extremely high noise levels(114-122 dB(A)) and widespread use(Bartholomae and Stein, 1988). Percussion drills will continue to be widely used to drill small diameter holes in hard rock because no other method seems to be economically avail-able to replace them (Boillat et al., 1993).Many studies (Danière, 1991; Hawkes etal., 1977a; Jensen and Visnapuu, 1972;Leblond et al., 1976; Milette, 1989) were con-ducted to determine the major noise sources of percussion drills. The exhaust air of pneumatic drills, the hammer, the bit in contact with the rock and the drill rod have been identified as the major noise sources. A muffer can be used to reduce the exhaust noise and the hammer can be enclosed. The bit noise is considered to be of concern only at the beginning of holes. When all the available methods are used to reduce the noise of a percussion drill, the drill rod vibrations become the dominant noise source (Hawkes and Burks, 1979). However, the noise levels generated by this source remain high and future efforts should concentrate on reducing its radiation.Works by Hawkes and Burks (1979) and Hawkes et al. (1977b) for the U.S. Bureau of Mines provide the most complete description on the noise and vibration of percussion drill rods.The longitudinal and bending waves are the two most important types of elastic waves generated in drill rods. Among these, only the longitudinal waves contribute to the drilling rate. The bending waves are caused by non-centralized impacts, drill rod curvature and non-uniform bit/rock interface. Drill rod noise is generated by Poisson’s ratio expansions and contractions of the rod as the longitudinal waves travel up and down it and by transverse rod motions induced by bending waves. The radiation efficiency is much higher for bending waves than for longitudinal waves. Most of the impact energy is transformed into longitudinal waves, as expected for axial impacts. The evaluation of the relative contribution of longitudinal and bending waves to noise generation poses a very difficult problem for experimental, analytical and numerical approaches. It is, however, an important issue because the relative contribution of these two waves will guide future noise reduction efforts. It seems that very little can be done to reduce the noise radiation of the axial waves without affecting the drilling rate. The main difficulty that analytical and numerical approach-es face, in the evaluation of the relative contribution of the two waves, is that there is no adequate theory for predicting the bending vibrations from the factors that cause them. The experimental approach has, thus, been limited to test fixtures that do not adequately represent the boundary conditions, as well as by measurements obtained under real operating conditions from which it is difficult to establish the relative contribution of the two types of waves. For example, Hawkes and Burks (1979) and Hawkes et al. (1977b) used a test fixture with free-free boundary conditions and made no clear link with measurement under real operating conditions. Rather, they have based their discussion on a simple model. Many authors assume that fexural waves are the main noise source on drill rods. However, measurements have been somewhat contradictory and researchers are still unable to state with certainty that this is indeed the case (Lednik et al., 1988)."

Jan 1, 1997

By B. W. Steele

"Dofasco began operations in 1912 as a steel foundry located in Hamilton, Ontario. Today, Dofasco is a fully integrated mill that manufactures hot rolled, cold rolled, galvanized and tinplate steels. Customers include the automotive, construction, tubular, manufacturing, appliance, packaging and steel ser-vice centre industries. Raw steel production and purchased semi-finished steel processed in1994 was 3.5 million net tonnes. Dofasco employs 7300 people at its Hamilton facility.Environmental management at Dofasco is guided by its environment policy and associated commitments. This paper discusses Dofasco’s responsibility for its products as it relates to these commitments. Dofasco is com-mitted to:n the principles of sustainable development that require that activities be conducted in a manner that provides for the present without compromising the ability of future generations to meet their needs. These principles will be integrated into product design, manufacturing and business planning;n managing renewable and non-renewable resources through the responsible application of reduce, reuse, and recycle principles;n minimizing any potential impact of its operations and products on the environment, employees, customers and the community;n continuous improvement of the effectiveness and integrity of our environmental management systems;n developing understanding among all employees about their responsibilities, and assigning the necessary authority; andn meeting the standards set by relevant legislation and international agreements through participation with governments and the diligent application of economically feasible and scientifically sound methods and technologies."

Jan 1, 1996

By Brett Schug, Caelen Anderson, Sohail Nazari, Carlos Cristoffanini

"The Haile gold mine in South Carolina is increasing the automation level of its processing plant in order to improve operational stability. One step toward this goal is the application of a digital twin concept to provide virtual instruments. Haile has engaged Andritz to implement virtual instruments at its grinding area hydrocyclones and at its tailing thickener underflow pump. These virtual instruments provide density values in a traditionally difficult location for reliable slurry density measurement. The digital twin is a first-principles integrated design engineering with advanced simulation (IDEAS) simulation model, connected in real time to the control system. Results have been promising, with the virtual instrument values matching the physical instrument under normal operating conditions and showing better prediction under upset conditions. Haile plans to use the virtual instruments as optional process control parameters.OceanaGold’s Haile gold mine is located near Kershaw, SC, about 80 km (50 miles) southeast of Charlotte, NC. This location was first mined in 1827 and has produced gold through several operating periods since then, including a heap leaching operation from 1985 through 1992. In October 2015, OceanaGold acquired Romarco Minerals, the previous owner of the Haile operation.The current operation began in 2017 as an openpit mine with additional underground resources. The nameplate throughput is 5,760 t/d (6,350 stpd) ore, and 2017 production was 3,345 kg (118,000 oz) gold, with 3,968 to 4,384 kg (140,000 to 155,000 oz) gold expected in 2018. Proven and probable reserves exceed 85 t (3 million oz) gold at a grade of 2 g/t (0.06 oz/st) gold. The process, as shown in Fig. 1, includes a primary jaw crusher, comminution with a semiautogonous grinding (SAG) mill and ball mill circuit, flash flotation, rougher flotation, regrinding, pre-aeration, carbon-inleach leaching, carbon elution and regeneration, cyanide recovery, electrowinning and refining. The Haile operation’s inaugural gold pour took place Jan. 20, 2017. Mine life is expected through the year 2030."

Dec 1, 2018

By William D. Cassity, Batric Pesic

Introduction Gold mining on an industrial scale is becoming increasingly dependent on low-grade refractory sulfide ores that contain large amounts of pyrite (FeS2) and arsenopyrite (FeAsS). Gold is usually present as sub-microscopic particles dispersed evenly throughout the sulfide matrix. Without some form of preoxidation, efficient recovery of this finely disseminated gold through cyanide leaching is hampered because the surface of the sulfide particle becomes passivated and impervious to penetration of the cyanide. Traditional methods for recovery of refractory gold from arsenopyrite ores include roasting and autoclave leaching. A modem alternative method is to preoxidize the mineral using the bacterium Thiobacillus ferrooxidans prior to attempting to re- cover the gold through cyanidation. The bioleaching of arsenopyrite ores presents a problem in the mobilization of large quantities of arsenic, present both in the +5 and +3 ionic states. Dissolved arsenic species pose a dual problem: they are -1 to the bioleaching process itself through inhibition of bacterial activity, and they also pose an environmental threat. The arsenate anion (AsO2) has been shown to be more toxic to living organisms, including Thiobacillus ferrooxidans, than the arsenate anion (AsO43) (Collinet and Morin, 1989). There is some disagreement as to the fate of arsenite in bioleaching solution. Mandl, Matulova, and Docekalova (1992) reported that dissolved arsenite concentration was constant during a long-term bioleaching study of chalcopyrite using Thiobacillus ferrooxidans. Torma and Oolman (1992) report that Thiobacillus ferrooxidans has been found capable of oxidizing As3+ to As5+. The solid products of arsenopyrite/pyrite bioleaching include jarosite (MFe3(SO4)2(OH)6 where M can be K+, Na+, NH4+ or H3O+), scorodite (FeAsO4.2H2O), ferric hydroxides, and ferric hydroxysufites (Carlson et. al., 1992; Van Breemen, 1982; Lazaroff et. al., 1982). The particular species formed is a function mainly of pH. Little study has been performed on the effect of solid products on bioleaching. Pesic and Kim (1993) showed that Thiobacillus ferrooridans cells served as a nucleation sites for jarosite particles, which grew rapidly and eventually killed the cell. Most bioleaching studies are performed at low pH&apos;s (<2.0) under uncontrolled conditions. By studying bioleaching of arsenopyrite under controlled pH conditions and at higher pH&apos;s (2.0 to 3.0), the distribution of iron and arsenic between the solid and liquid phases can be controlled, and their effects studied. The objective is to develop a bioleaching process that operates at high efficiency while keeping amounts of dissolved heavy metals low. Pesic, Stohok, and Torma (1993) demonstrated the usefulness of this approach in the leaching of cobaltite (CoAsS) concentrates. Materials and Methods The focus of this study was the bioleaching of arsenopyrite ore by Thiobacillus ferrooxidans. The parameters studied included the effects of pH, and the effects of arsenate (AsO43 and arsenite (AsO2). pH studies included pH set initially but not controlled, and pH controlled continuously with NaOH or LiOH. Bioleaching results from two strains of Thiobacillus ferrooxidans with different adaptation histories were compared. Bioleaching experiments were conducted in 150 ml stirred glass reactors using a strain of Thiobacillus ferrooxidans adapted to arsenopyrite ore, supplied by the U.S. Bureau of Mines. These bioreactors were innoculated with stock cells grown on arsenopyrite ore for 14-16 days. Typical elemental breakdown for this ore was: As, 9.90%; Fe, 18.60%, Stot, 9.26%; Suifide, 7.50%; SiO2, 25.90%. Mineralogically, the ore contained both arsenopyrite and pyrite. Bioleaching efficiency was measured by withdrawing bioleach solution samples at selected intervals, filtering, and measuring the amount of dissolved cobalt, iron, and arsenic by atomic absorption spectroscopy. Because the precipitation of iron and arsenic at higher pH&apos;s would lead to unreliable results, a 100 mg tracer of cobaltite concentrate from the Blackbird mine in southern Idaho was added to solution. Dissolution of the cobaltite tracer was used to indicate bioleaching of the bulk arsenopyrite ore. Cobalt has been shown to be stable in solution even when iron and arsenic were precipitated (Pesic, Storhok, and Tonna, 1993). The pa-

Jan 1, 1995

The Bibliographic Data Base is the result of a literature search con-ducted as one task of the technology assessment of current and advanced logging techniques, sponsored by the United States Bureau of Mines. After compilation, the bibliography was converted to an automated form for ease of utilization, and to allow for maintaining and updating the data base. The data base covers articles, symposia, books, patents, corporate and government reports, and other literature concerned with some aspect of borehole logging from January 1969 through December 1975. Periodic up-dating will be necessary to keep the data base contents in step with developments in the rapidly advancing field of application of borehole logging to mining. Many bibliographic indexes were scanned for entries relating to the subject of interest, and those entries which were included in our data base contain a reference to the bibliographic index in which they were listed (see Section 2.4.7). With the aid of these indexes, a vast number of publications, including foreign reports and publications, have been scanned for works relevant to borehole logging technology.

Jan 1, 1976

By Andrew Scogings

The current edition of The Australasian Joint Ore Reserves Committee (JORC) Code was published in 2012 and, after a transition period, the 2012 edition came into mandatory operation on Dec. 1, 2013. There is a significant change between JORC 2004 (Clause 44) and JORC 2012 (Clause 49) for the reporting of industrial mineral resources and reserves, which should be addressed by ASX-listed players in the industrial minerals space.

By Alejandro Uribe-Salas, Fabiola Nava-Alonso, Gloria Dávila-Pulido

This paper presents results of an experimental study performed on the role of calcium sulfate present in flotation water on sphalerite flotation in the Pb/Cu circuit (non Cu-activated sphalerite) and in the Zn circuit (Cu-activated sphalerite). In the Pb/Cu circuit calcium ions adsorb on the negatively-charged sphalerite favoring xanthate adsorption and therefore making sphalerite floatable; experimental measurements show sphalerite contact angle increases with calcium concentration while xanthate adsorption onto sphalerite increases with the increase of pH and calcium concentration. Gypsum (CaSO4·2H2O) eventually present due to calcium sulfate precipitation is not detrimental to flotation at this stage since it is negatively charged at pH 9 and therefore, does not adhere onto the surface of negatively-charged sphalerite. In the zinc circuit, Cu-activated sphalerite decreases its negative charge (or even becomes positively charged) and develops some hydrophobicity due to the polysulfide produced by Cu-activation. At this stage calcium ions do not interact with the mineral surface and therefore do not favor xanthate adsorption; nevertheless, precipitated gypsum particles do adhere onto the mineral surface, greatly affecting its floatability (e.g., contact angle). Addition of sodium carbonate to dissolve gypsum and to precipitate calcium as calcium carbonate, which disperses in the bulk of the suspension, effectively restores mineral hydrophobicity. SEM observations coupled with EDS analysis clearly illustrate and support the above sequence of events.

Jan 1, 2014

By Donald T. Hawkins, Ralph Hultgren

The lorsion effusion method has been used to measure the vapor pressure of lead over pure lead and eight Pb-Sn alloys ranging from 9.1 to 87.9 at. pct Pb in the temperature range 950° to 1125°K. The resulting ?H°y 298 = 46,630 ± 200 cal per g-atow for pure lead is in excellent agreement with previous work. Deriued ?Gph values for the alloys were smoothed and correlated with previous heat of formation data to obtain entropies for the liquid alloys. values for the tin component were calculated by Gibbs-Duhem integmtion. Surfhce depletion of these liquid alloys was found to be absent, as shown by the fact that the measured pressure remained substantially constant with time in contrast with previous measurements on iron-rich solid Fe-Mn alloys. The activities and Gibbs (free) energies of the liquid Pb-Sn system are not well known although the heats of formation have been accurately determined by K1eppa.l Vapor pressure determinations of the activity of lead by Voronin and Evseev2 disagree with those of Predel.3 Elliott and chipman4 measured activities by the electromotive -force technique in the ternary Pb-Sn-Cd system. From the resulting values of the activity of cadmium, they were able to calculate the activities of lead and tin for the binary Pb-Sn system at the compositions xsn = 0.33 and 0.67. Atarashiya, Uta, Shimoji, and Niwa5 determined the activity of tin from Hz-H2O equilibrium measurements, but their results are subject to question due to uncertainty in the final state of their samples. To resolve these differences, measurements of the activity of lead were made using a torsion-effusion apparatus. Among other advantages, this apparatus rapidly detects errors caused by surface depletion, which tends to reduce the apparent vapor pressure of the more volatile component. If the measured torques remain nearly constant with time, only bulk depletion is occurring. This contrasts with the rapid decrease in torque found in solid Fe-Mn alloys at high temperatures and low manganese contents.6 EXPERIMENTAL 99.999+ pct Pb was obtained from the American Smelting and Refining Co. and 99.999 pct Sn from Vulcan Detinning Co. Eight Pb-Sn alloys were prepared by melting together weighed amounts of the pure metals in evacuated Pyrex tubes and quenching the melts in water. Loss of weight in preparation was less than 0.02 pct in all cases. The effusion cells were made from high-purity, nonporous graphite. Graphite was chosen because of its resistance to reaction with lead and tin and because it can be accurately machined with precision orifices. Two cells were used with overall dimensions as shown in Fig. 1. The orifices of cells 1 and 2 were, respectively, 1 and 1.5 mm in diam.

Jan 1, 1968

By Jonathan J. Dewsbury

It is argued that approximate computer based methods are only suited to modelling conventional piled rafts, for pile enhanced rafts where the interactions will be non linear three dimensional finite element analysis is required. However current 3D finite element analysis often relies on symmetry to reduce computational cost and there are concerns over the dependency of the results on the user. Therefore a new strategy within the finite element framework has been proposed. The main advantage of this strategy is that each stage of the model can be checked for consistency. There is also the added benefit that non symmetrical models can easily be constructed by tying the validated components together without dramatic increases in computational time. The proposed strategy compared well to the published results of a hypothetical example of a piled raft previously analysed with numerous methods by Poulos et al. (1997).

Jan 1, 2010

By E. D. Gálvez, L. A. Cisternas, R. Acosta-Flores, F. A. Lucay

The optimal design of flotation circuits is a complex task as the mathematical model is nonconvex and includes binary variables, making it difficult to obtain the global optimum solution. Furthermore, there are epistemic uncertainties in the evaluation of the performance of flotation and grinding units. This epistemic uncertainty is generated because semi-empirical models are used with parameters that are a function of the circuit design. Therefore, it is not possible to adjust these models based on experimental data as the experimental conditions are not known at the design stage. This paper analyzed the effect of the uncertainties in flotation units, grinding units, and both units simultaneously. As a result, this paper demonstrated that, for a specific mineral, few structures exist that are optimal for a wide range of values in flotation stage recoveries and liberation fractions in the grinding units. A remarkable aspect of this work is that it introduces grinding, one of the operations that most influences energy consumption in mining and has not been studied in depth in the design of flotation circuits. To demonstrate that there are few optimal structures for a specific mineral when there is high uncertainty in the process units, an a priori approach or first principles was used. Two methods of proof were used: proof by construction and proof by exhaustion. Proof by construction is the construction of a concrete example with a property to demonstrate that something having that property exists. In this work, two examples were considered in the proof by construction. In proof by exhaustion, the conclusion was established by dividing it into a finite number of cases and proving each one separately. Here, 30,000 cases were included for each example. This knowledge can be useful in circuit design including grinding, e.g., after selecting the circuit (or the most promising circuits), and the equipment design parameters and operating conditions can be defined based on simulation and laboratory tests.

Jan 1, 2018

By Luis Fernandez-Deza, James Hawn, Dustin Mount, Jean-Marc Wehrli

The RiverRenew Tunnel System project in Alexandria, VA forms part of a CSO scheme aimed at reducing overflows of combined stormwater and sewage into the Potomac River during storm events. A major piece of the project is a 12-foot internal diameter tunnel of approximately 12,000 feet length lined with a single-pass precast concrete segmental liner and excavated by an Earth-Pressure Balanced Shield TBM. The tunnel lies between 120 to 140 feet below grade in the clays of the Upper Potomac Formation with occasional dips of more granular, saturated soils of the Terrace Formation and the Alluvium. The TBM is launched from a figure-8 configuration Pumping/Screening Shaft located within AlexRenew’s operational Water Resource Recovery Facility. This paper discusses the challenges encountered during the launch of the TBM in short mode within a highly congested site and from narrow deep shafts.

Jun 13, 2023

By V. Ramachandran

Over the past 20 years, water treatment plants have been built at various Asarco facilities to effectively handle the process waste streams that need to be bled from the system. The current paper review the several operations with reference to (a) waste streams processed, (b) process chemistry, (c) discharge options and recovery of treated water, and (d) sludge disposal.

Jan 1, 1994

By D. Baker

Alternative material handling methods are allowing material handling operations to be performed with increased cost savings. This allows for higher production levels with better returns. RAHCO International Inc.&apos;s Continuous Mining Excavator (CME) has recently received a lot of attention due in part to its operating efficiency, flexibility, and associated low operating costs. The CME is designed to perform three primary functions. These include material excavation, sizing and loading operations. In many applications, a drilling and blasting process can be eliminated. The CME was developed originally in 1985 for open pit coal mining. See figure I. Since this time, it has been proven an effective system for excavating many other types of materials including friable and sticky materials. It has also been shown to suitably handle hard rock in certain site conditions.

Jan 1, 1998

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata, Dohta Awaji

"The immediate ring closure method, in which the entire periphery of the excavation area is closed immediately with an initial support within a short distance from the excavation face, has been increasingly used in Japan, especially, as one of the most effective countermeasures against difficult ground conditions in conventional tunneling. For reasonable design of this method, the performance requirements for the initial support should be clearly stated. The analysis of construction data of 30 road tunnels and the three-dimensional numerical modeling based on real data suggest that the immediate ring closure stabilizes the tunnel structure and the ground around it because of the inner pressure effect of the initial support, especially, for low ground competence factor and small internal friction angle. Finally, the bending compressive strength and the cross-sectional geometry of the initial support have to be considered in the tunnel design while considering the earth pressure and ground properties. INTRODUCTION Conventional tunneling methods often deal with difficult ground conditions such as soft ground or squeezing ground conditions. The immediate ring closure method, in which the entire periphery of the excavation area is immediately supported within a short distance from the excavation face (Figure 1), has been increasingly used in Japan as one of the most effective countermeasures against difficult ground conditions in conventional tunneling (e.g. Takahashi et al., 2011; Nakaoka et al., 2013). The immediate ring closure method was empirically identified as effective for reducing ground surface subsidence and tunnel deformation. However, the working effects of the method have not been clarified sufficiently. To improve the design of this method, the working effects of this method and the performance requirements for the initial support need to be clarified. The relation between the effect of immediate ring closure and earth cover has been clarified (Mashimo et al., 2008; Awaji et al., 2013),"

Jan 1, 2016

By J. E. Dutrizac

"The end of an era in zinc metallurgy took place on July 31, 1976 when the horizontal retort furnaces of the National Zinc Company in Bartlesville, Oklahoma were permanently shut down (1) . For more than a century, horizontal retorting had been the most common method of producing zinc in the United States; it was a thriving industry in many parts of that country, especially in the natural gas belts of Oklahoma and Texas. With the Bartlesville closure, yet another metallurgical process has become an object of historical interest for North American metallurgists. Although shrouded in controversy, the origins of zinc metallurgy seem to date back at least 2000 years. Pyrometallurgical methods with carbon reductants are capable of producing zinc from oxidic zinc ores, but only above the boiling point of the metal. Although slow cooling results in re-oxidation of the zinc vapour by air or carbon monoxide, quenching yields liquid zinc; some form of rapid cooling, either accidental or intentional, was likely used by ancient metallurgists to liquify the metal. Zinc metal found in Athenian objects of the Roman era was likely of accidental origin. The Romans employed brass extensively for coins and ornaments(2) , and this was intentionally produced by the calamine process whereby oxidic zinc ores were added to molten copper under strongly reducing conditions. Zinc appears to have been known in China and India as early as 1000-1300 A.D., and was probably smelted commercially in those countries from the 14th century. Although the early metallurgical procedures were probably inefficient, they were able to produce zinc metal in significant amounts. The large heaps of zinc residues with clay retorts bear testimony to an early smelting industry of impressive magnitude. It is estimated that the heaps at Zawar, India alone represent the extraction of 100 000 tons of metallic zinc(2) In the 1730s the smelting of oxidic zinc ores was developed in England using a vertical retort method. In 1788 a British patent was granted for making zinc from zinc blends (ZnS) by roasting the ore in a coalfired reverberatory furnace, mixing the calcine with charcoal and smelting the mixture with suitable zinc condensation. The English process was very energy intensive, however, and early in the 19th century the Belgians developed a horizontal retort process for the reductiondistillation of zinc that was more fuel efficient. This technique was gradually developed into what came to be known as the Belgian process, the forerunner of the ""modern"" horizontal retort furnace."

Jan 1, 1999

By H. Bouzahzah

The field of quantitative mineralogy has evolved significantly through the development of image analysis techniques and information technology. Quantitative mineralogical characterization can now be routinely conducted for determining ore compositions and understanding the behaviour of minerals within mineral separation processes. The characterization of mine tailings is another important application of quantitative mineralogy. The estimation of acid and neutralization potential as well as the interpretation of kinetic leaching test results are often based on quantitative mineralogical knowledge (mineral abundance, texture, metal distribution amongst minerals, etc.). The objective of this paper is to determine and compare the accuracy of four mineralogical characterization techniques that are often used for environmental sample analysis: (1) X-ray diffraction, (2) normal analysis from chemistry analyses, (3) normal analysis from specific gravity measurements and (4) SEM-EDS image analysis. For this purpose, three artificial samples were assembled by mixing pure minerals in proportions often observed in mineral processing plant tailings. BILMAT, a statistical data reconciliation software, was applied to reconcile the chemical analyses with the results of other mineralogical analysis techniques and to estimate the acid and neutralization potential of actual mine tailings samples. The acid mine drainage was qualified from the acid potential and neutralization potential equilibrium as determined through quantitative mineralogical analysis. The statistically reconciled data made it possible to predict the metal deportment as a function of their bearing minerals and therefore, in the case of neutral contaminated drainage, to assess metal leaching potential.

Jan 1, 2016

"The Industrial Comminution Efficiency (ICE) working group, part of the Global Mining Standards and Guidelines Group (GMSG) has engaged a large number of industry professionals representing mining companies, equipment vendors, consultants and metallurgical laboratories with interests and capabilities in the comminution field. These participants have collaborated to develop three guidelines for the assessment of the efficiency of mineral comminution circuits. Two of these guidelines deal specifically with power based modelling techniques to quantify energy efficiency using widely practiced techniques, those developed by Bond (1961), Rowland and McIvor (2009), and Morrell (2009). The third guideline deals with the sampling and surveying of grinding circuits as is required to provide the necessary information, at appropriate quality, to furnish the efficiency analysis promoted by the first two guidelines. This preprint will focus on the Guideline on Methods to Survey and Sample Grinding Circuits, which is currently in the final stages of peer review and finalization by the GMSG. INTRODUCTION It is important to make a clear distinction on the scope of work of the GMSG guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and as a result require a large amount of information to calibrate and validate the unit models. As a result these surveys are labour intensive, somewhat expensive depending on internal capabilities of the mine site or company, and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions. As a result of these factors full grinding circuit surveys are not a common occurrence at a large number of facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices. To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. It can also be manipulated by experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, supporting an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2016

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 64 to 10,000 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

Separation of dolomite from Florida phosphates was achieved by first conditioning the feed with fatty acid at pH 10 followed by reconditioning at pH 4 or below, before flotation. Observed selectivity of this two stage conditioning process was attributed to the amount as well as changes in the nature of the adsorbed collector species upon reconditioning. In this paper, bench scale flotation results of optimizing the major process parameters, such as reconditioning pH and collector dosage, for upgrading natural high dolomitic phosphate samples from Florida are discussed.

Jan 1, 1988