Search Documents

By David W. Zeeb

The use of an ordinary VHS video camera and a four-head player can be an effective tool to analyze surface blasting. The necessary equipment can be purchased for under $1,300 and will allow frame by frame or slow motion viewing of a blast in 33.33 millisecond increments. Rock breakage, movement, and timing can be studied in high quality slow motion. These studies can result in improved blasts by showing things that the eye can miss in real time.

Jan 1, 1992

By R. G. B. Pickering

Successful management of mining operations depend on the accurate and reliable measurement of performance as a monitoring instrument in a feedback and control loop. However, when changes are being considered, the probable effect of the change on bottom line results requires different measuring techniques incorporating an in depth understanding which can identify hot spots in the operation which exhibit strong sensitivity to change. The CSIR's Division of Mining Technology has therefore been devoting a considerable effort to the establishment of techniques which enable changes to be analysed in terms of their impact on the two key parameters describing mine performance, i.e. profitability and safety. This paper describes these techniques, outlines their application to some example situations and discusses planned enhancements. The first section of the paper addresses the profitability model, and this is followed by a section considering the mine safety model.

Jan 1, 1996

By Gwenaële Petit, Ulan Massimkhanov, Gilles Joubert

For its Zuuvch Ovoo uranium deposit in Mongolia, Badrakh Energy (partly owned by Orano Mining) is working on the prefeasibility study for exploitation by ISR (in situ recovery). As part of this project, Orano built a 2-cell (each cell is constituted of one producer well located in the center and surrounded by six injection wells in an hexagonal pattern) and a processing pilot plant that will be used to demonstrate the operability and economic viability of an ISR process. Another main objective of this pilot trial is to demonstrate the ability of Orano’s modeling tools to predict the ore behavior under given leaching conditions. To model uranium production by ISR, Orano uses HYTEC, a reactive transport computational software, which was adapted for its existing operation in Kazakhstan (Katco) to predict uranium recovery and reagent usage based on operating conditions. In order to perform similar simulations for this new deposit, Orano engaged in a comprehensive program including ore sampling, detailed characterization, and metallurgical testwork. The mineralogical conclusions were used to prepare a simplified geochemistry for the ore, in particular carbonate and reactive clay grades, uranium mineralization and penalizing elements such as pyrite. Then, bottle roll leach tests were used to characterize dissolution kinetics for smectite clays. Eventually, column leach test results such as pH, free acid, and uranium recovery were modeled on HYTEC to improve the fit of some of the dissolution kinetic parameters. Parameters fitted using metallurgical test work results will now be used as inputs for predictive model at the pilot scale, in order to anticipate operational results and help with operating decisions for production ramp up.

Jan 1, 2020

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluates the effectiveness of similitude theory in predicting the draft of a rubber tire loader’s bucket during initial penetration. The work uses 1:16 and 1:8 scale models of an 18-t capacity load haul dump, scaled with the Buckingham Pi theorem, to evaluate the prediction of draft and penetration under different operating and different dynamic conditions. We hypothesized that the observed relationships between draft and longitudinal penetration and the operating and dynamic conditions will hold true for an upscaled model. Similarly, we hypothesized that the results of experiments conducted with the smaller scale model should predict the draft on an upscaled model.

By R. L. Veenstra

This paper explores the connection between the stresses observed and the failure mechanisms present in the modelled cemented paste backfill. In order to look at this connection, the authors have used a previously developed model to conduct a sensitivity analysis of the model?s strength and permeability input parameters. The results from the sensitivity analysis were then compared to determine what causes modelled stresses and failure mechanisms to vary. Increased insight into the behaviour of the modelled paste will help clarify how paste behaves in the field.

Aug 1, 2013

By Mariana H. Staia

The present communication reports the results obtained by applying different concentration methods, at laboratory level, to the black sands from Estado Bolivar, Venezuela, with the aim of obtaining an adequate ilmenitic concentrate for the subsequent chlorination process. Sizing analysis was performed and plasma emission spectroscopy method was used to determine the chemical composition. It was found that from the two hydrogravimetric methods used, the Humphrey spirals is much more effective than Wilfley tables, leading to a 85% recovery. The most convenient particle size group for these concentration methods was the one corresponding to ASTM 40-140 mesh. When magnetic concentration was applied to the concentrate, obtained as a product from Humphrey spiral, a recovery of ilmenite more than 90% was obtained in the first step. It has been shown that the ore would respond to the separation techniques employed, giving individual minerals: ilmenite, zircon and silica as concentration products.

Jan 1, 1995

By M. L. Torem, R. H. Rojas, A. G. Merma

"Fine particle recovery by conventional flotation processes is very low mainly due to the low probability of bubble/particle collision and adhesion. In order to solve the problem of low particle recovery, several flotation technologies have been developed to increase bubble/particle collision efficiency. Among these technologies, the electroflotation process stands out. This process has advantages in the generation of microbubbles (<100 µm) and in the production of different amounts of hydrogen and oxygen microbubbles. These advantages favorably influence the fine particle floatability, due to the greater probability of particle/bubble collision and adhesion. The electroflotation tests were conducted for a hematite/sodium oleate system in a Partridge-Smith modified electroflotation binary cell of 0.38 L usable volume. The sodium oleate concentration, particle size, pH and current density were evaluated. Satisfactory results in the recovery of hematite were found at pH values of 7, reaching hematite floatability of 99% and 90% with hydrogen and oxygen bubbles, respectively.INTRODUCTIONThe flotation recovery of fine and ultrafine particles is normally very low and is caused by several factors, among them, the low probability of collision and adhesion bubble-particle, the difficulty to overcome the energy barrier (entrainment and entrapment), low selectivity, surface oxidation and mineralogical changes (Schulze et al., 1989; Waters et al., 2008; Shahbazi et al., 2010). This problem can be overcome by decreasing the bubble size or by increasing the apparent particle size. However, it is worth noting that the use of small bubbles or micro bubbles also involves some disadvantages such as their low momentum resulting in a slower process comparing with conventional flotation. Electroflotation is an attractive alternative for treating fine particles with small bubbles less than 100 µm, generated by the electrolysis of water. Electroflotation is one of the variants of the flotation process, where the gaseous phase is produced by electrolysis of an aqueous solution, generating oxygen and hydrogen bubbles (Sarkar, 2010; Gupta and Ali, 2012). These smaller size bubbles allow the recovery of fine particles by increasing the collision efficiency. This process is versatile and competitive in relation to other techniques such as dissolved air flotation and dispersed air flotation because the electroflotation units are smaller, more compact and require less maintenance and less operating cost than other flotation units (Zouboulis and Matis, 1995,). In addition, the electroflotation process is a clean technique and provides results in a short time, requiring only the investment in the electroflotation cell construction stage and the choice of the electrodes (Ketkar et al., 1991; Sarkar et al., 2010; Sun et al., 2011). In this sense, this study assesses the effect of pH, particle size and sodium oleate concentration on electroflotation of hematite fines."

Jan 1, 2018

By Ronald B. Stotelmeyer

This report summarizes studies of 55 Idaho national forest roadless areas completed by the U.S. Bureau of Mines (USBM) in the period 1966-1992. These roadless areas have been recommended for addition to the National Wilderness Preservation System, proposed as special management areas, or otherwise recommended for study by the U.S. Forest Service or the Idaho congressional delegation. The Bureau of Mines&apos; studies indicate which parts of the roadless areas contain mineral resources. They also show where mining and prospecting are likely to occur in the future, where mineral production has occurred in the past, and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character.

Jan 1, 1994

By Raymond B. Ladoo

Deposits of talc are known in many districts in Canada but at the present time active mining operations are reported only in Ontario . Here three companies are now operating, two of which, George H. Gillespie & Co. , Ltd. , and the Anglo- American Talc Co. , are at Madoc . The operations of the former company are probably the largest and best known in Canada . The writer , in his capacity as an engineer of the U. S. Bureau of Mines , was permitted by this company to make an inspection of its mine and mill in June, 1920 , and study the methods employed . This information was desired for comparison with methods employed in the United States . The following description is based on observation made during this visit , supplemented by data supplied by the company .

Sep 1, 1920

By Kai Wang, Chao Xu, Qiang Fu, Tong Yang, Chunyu Zhao, Wei Zhao

The stress of a coal seam is an important factor that affects the permeability of the coal seam and then affects the coalbed methane (CBM) drainage. In China, adjacent coal seam mining is an important method to reduce stress, which increases the permeability of the coal seam. However, in the process of mining adjacent coal seams, many coal pillars remain, which causes stress concentrations and results in a decrease in permeability. Therefore, it is important to study the influence of coal pillars on the stress of adjacent layers and its distribution and evolution in the floor rock. This paper took the Shendong Baode Coal Mine as a case study and investigated the influence of the coal pillar on the stress and permeability of coal seam #11. The results show that under a coal pillar, the relationship between the vertical stress of different floor depths and the width of the coal pillar can be divided into a negative correlation zone, transition zone, and positive correlation zone. The change in the coal pillar width does not affect the pressure relief range or the degree of pressure relief in the adjacent coal seams below the goaf. The field measurements show that after the mining of panel #81,505, the permeability coefficient of coal seam #11 under the goaf increased from 0.1434 to 26.3545 m2/( MPa2*d), increasing 182.7 times, and the drainage mixing volume of boreholes #1 and #2 increased from 1.24 to 1.52 m3/ min. While the permeability coefficient of coal seam #11 from 12.5 m in the coal pillar has only increased by 2.6 times, the drainage volume of boreholes #3 and #4 did not change significantly.

Nov 19, 2022

By Robert S. Williams

NO new ferrous alloys have been produced in the last five or six years that are as outstanding contributions to civilization as were the high-speed steels of the early part of the century or the stainless steels announced at the close of the World War. There have been, however, many developments of major importance having to do either with modifications of existing alloys or with new methods of treatment of older iron or steel alloys. Only a limited number of these new developments can be discussed and their selection does not necessarily imply that these are the most important but merely that they are of general interest rather than perhaps of greater importance in highly specialized fields.

Jan 1, 1939

By Yuri Hovanski, Jingyi Zhang, David P. Field, Piyush Upadhyay

Friction stir welding has gained wide interest in industry and drawn large research attention due to its high level of automation and superior joint performance. In this study we further expand the welding parameters to be of magnitudes higher than those previously reported to lower the cost and enable high volume joint production. Sound butt-joints were produced with aluminum alloy 6111-T4 blanks with welding speeds up to 6000 mm/min. Tensile tests of the joint pieces show >97% joint efficiency in terms of ultimate tensile strength. The T4 natural aging and grain refinement is found to contribute to the superior joint properties. Electron backscatter diffraction (EBSD) analysis is used to qualitatively study the local shear texture inside the nugget zones of the welds. The shear texture result is a good indicator of the material flow directions in the nugget zones. The flow directions behind the rotation tool are found to be flattened towards the top surface of the workpiece when the welding speed is increased, suggesting intense material mixing and transportation along the longitudinal welding direction (WD).

Mar 1, 2018

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By Christie Myburgh, James Mackenzie, Ross Hammond

Modern mining operations are increasingly characterised by their access to large volumes of data and advanced computational tools. Over the past two decades, the industry has made substantial investments in digital technologies supporting geological modelling, mine planning, equipment dispatch, and process control(Newmon et al., 2010; Paraszczak, 2019). These systems have significantly improved the ability to generate and analyse information across the mining value chain. However, despite these advances, the decisions that ultimately determine operational performance remain largely implicit and unmanaged (Kruger et al., 2023; Jia, 2022). Mining decisions rarely occur in isolation. Decisions made in geology influence resource models, which shape mine plans, production schedules, and downstream processing strategies. These, in turn, affect operational execution. As deposits become deeper, ore grades decline, and operational constraints increase, these interdependencies create increasingly complex decision environments (Newman et al, 2010; Topal, 2008; Darling, 2011; Dimitrakopoulos, 2004). In practice, coordination across these domains often relies on informal communication, iterative meetings, and manual interpretation of analytical outputs. Explicit decision support systems provide a mechanism to capture these dependencies, maintain consistent decision context, and coordinate decision-making across geological, planning, and operational domains (Power, 2002; Shim et al., 2002). This paper argues that a fundamental gap remains in current digital mining systems: while data and analytics are well supported, decision-making itself is not. Addressing this gap requires treating decisions as explicit, structured elements within the operational system. By integrating data, computational analysis, and decision processes, explicit decision support systems offer a way to better coordinate complex, interdependent decisions across mining operations.

May 2, 2026

By Jiaqi Jin, Jan D. Miller, Chen‑Luh Lin, Amanda N. Erskine, Shijie Wang

Recovery of metals from coarse ore particles is a great challenge for heap leaching operations of low-grade precious metal resources. Internal fractures of ore particles like micro-cracks can facilitate subsurface transportation of solution inside particles and leaching of valuable minerals. A plant-scale high-pressure grinding roll (HPGR) unit at Coeur Mining’s Rochester mine was operated at selected specific pressures to crush and prepare various products for crack analysis using high-resolution X-ray computed tomography (XCT). 3D shapes of cracks inside ore particles for selected size fractions reveal different damage mechanisms during HPGR crushing regarding particle size and crushing pressure. Close-to-surface cracks formed by abrasion were found in small 2.5 mm particles. Impact cracks with a high aspect ratio were found in particles of larger size and higher HPGR pressure. The volumetric percentage of internal fractures and the specific crack surface areas of selected ore particles are compared to give quantitative conclusions on particle damage by compression during HPGR crushing.

Apr 20, 2024

By E. H. Cho

Pittsburgh #8 coal cleaned by the conventional froth flotation was oxidized in a 2-liter Parr Stirred Top Bench Reactor. The oxidation time was varied up to 5 hours; the temperature, from 150 to 225°C, the oxygen pressure, from 15 to 500 psi; and coal dosage, from 15 to 60 grams in 600 ml of distilled water. The oxidation of coal was evaluated by measuring total acidic group formed on the coal surface as well as by measuring the adsorption of calcium ion from a solution under standard conditions. It was found that the oxidation increased with increasing oxygen pressure without much leveling-off effect. However, the oxidation of coal increased sharply from 150°C to 175°C and then tended to level off above 175°C. The adsorption of calcium was reached more than 3% on the coal oxidized under favorable conditions. The adsorption of calcium on coal increased sharply with increasing equilibrium pH. The BTU loss was sensitive to oxidation temperature. This study concludes that the optimum oxidation of coal should be conducted at high oxygen pressures around (e.g. 500 psi) 170°C for 3 hours. This study also concludes that the oxidation in an autoclave is far superior to that in a fluidized bed in terms of calcium adsorption, BTU loss and reaction time.

Jan 1, 1994

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires burning in 9 states. This is considered by experts to be an underestimate for the actual number of fires nationwide. Abandoned mine fires, if left uncontrolled can burn for years and in fact, one of the most well-known mine fires in the US, the mine fire in Centralia, PA, which began in 1962 has been burning for over 55 years. In Centralia, the mine fire won the battle, despite suppression and control efforts, as most of the residents were bought out by the State of Pennsylvania and moved away. However, the world record for the longest-burning coal fire, which may have been started around 6,000 years ago in New South Wales, Australia is still smoldering. Suppressing a coal mine fire requires cooling the hot zones and removing any source of oxygen. If the workings are shallow, the fire zones can be unearthed and the burning rock mass can be quenched on the surface. If the workings are too deep to excavate, then the fire must be fought remotely through boreholes using a variety of agents including water, gas-enhanced foam and grout. Access to surface areas for drilling can be problematic due to topographic and property constraints. When this occurs, large areas of burning may go unaddressed or simply left to burn. Fire Solutions, Inc. has been investigating the use of gas-enhanced foam in concert with directional drilling technology. Gas-enhanced foam has the advantage of using less water and adds inert nitrogen gas to displace oxygen to infiltrate and suppress a fire. Directional drilling has the capability to steer a borehole to a specific place underground. Directional drilling has many advantages over conventional drilling technology as it can provide the least disruption to the ground surface, minimize surface preparation and reclamation costs, multiple sites can be accessed underground from a single site and thus treated simultaneously and it offers increased efficiency because it is not constrained by difficult terrain. This paper discusses the combined use of these two technologies and it is hoped that with the use of these two technologies the efficiency and capability to address mine fires will be significantly improved. INTRODUCTION According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in 9 states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging damage overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards [1]."

Jan 1, 2018

By Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industry despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. In order to reduce cases of Noise Induced Hearing Loss (NIHL) in the mining industry, retrofit acoustic treatments and controls are being developed to subdue noise at the source. The Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2005 has determined that continuous mining machines rank first among all mining equipment whose operators exceed 100% noise dosage. The continuous mining machine conveyor, used to move coal from the cutting face to the rear of the machine, has been identified as a dominant noise source. A dual sprocket conveyor chain was tested as a potential solution. Sound power level measurements conducted at the Pittsburgh Research Laboratory (PRL) accredited reverberation chamber showed a 3 dB reduction in the A-weighted sound power level when the dual sprocket chain was implemented. Underground results show an 8-hour Time Weighted Average (TWA8 hrs) reduction a 3 dB for continuous mining machine operators. Utilizing this newly developed noise control, along with previously proven controls, provides continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2009

By A Giblett, M Daniel

"The Global Mining Standards and Guidelines Group (GMSG) currently supports nine individual industry working groups focused on developing standards and guidelines for the mining industry. In 2013 the GMSG established the Industrial Comminution Efficiency (ICE) working group to develop freely available guidelines for plant operators to quantify the operating efficiency of industrial comminution circuits. This initiative has engaged a diverse group of representatives from mining companies, equipment vendors, consultants and metallurgical laboratories with vast experience and capabilities in the field of comminution. The GMSG has issued the first two guidelines from the ICE working group in 2015–2016, with the third guideline having completed the approvals process and being in the final stages of editing ahead of release later in 2016.Two of the ICE guidelines present methods to quantify comminution circuit efficiency, and a complementary guideline describes best practice methods to collect the necessary samples and data to furnish these assessments. Collectively the guidelines cover sampling, survey data collection, laboratory testing procedures and calculation processes to allow the user to generate a relative circuit efficiency factor for the comminution circuit at the time of survey. The reference energy consumption is calculated considering the measured F80, P80 and ore strength at the time of survey, using either or both of the Bond or Morrell methods presented in GMSG guidelines dedicated to each method. The guidelines consequently provide the end user with practical tools to perform circuit efficiency analysis and to readily quantify the impact of optimisation efforts.This paper presents the content of the three ICE guidelines and describes their intended application.Citation:Giblett, A and Daniel, M, 2016. Global Mining Standards and Guidelines for Determining Comminution Circuit Efficiency, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 3&ndash;8 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Bertrand L. Johnson

Fertilizers are indispensable to national preparedness and defense. Production of adequate supplies of nourishing food for sustaining life in the United States is absolutely dependent in many parts of the country on the use of artificial fertilizers of various types. Only by using fertilizers can we maintain our present volume of production without great additional expense. Otherwise we would have to increase crop areas constantly to compensate for declining yields, we would have to lower the quality of food marketed, and standards of farm living and rural civilization would decline. About 60 million of the 360 million acres of crops grown annually in the United States Vow require fertilizing each year, and between 7 and 9 million tons of commercial fertilizers are consumed annually for this purpose.

Jan 1, 1941