Search Documents

By I. M. Santos Moraes

The control of minor impurities (mainly As, Sb and Bi) in copper refineries has been a great challenge. Caraiba Metais' copper refinery produces a very high quality copper, registered in LME as grade A, and recognized as amongst the top ten in the copper world. At Caraiba's Tankhouse Bi and Sb are controlled by means of electrolyte bleed-stream removal after partial decopperizing in a set of electro-winning cells (liberators). Another way of reducing the Sb and Bi content in the electrolyte is by means of the arsenate precipitation chemistry. It is well known that the use of high arsenic concentrations in copper refinery electrolyte has the advantage of causing most of the bismuth and antimony to report in the anode slimes. However, the use of such mechanism of control may contribute to other undesired problems such as antimony and bismuth precipitation in the bulk of the electrolyte, what may cause severe contamination problems. This paper describes a period when some cathode contamination with Sb occurred at Caraiba Metais' Copper Refinery. It also presents an analysis of several process parameters related to the problem, the possible causes for the contaminations as well as the actions taken to correct the problem.

Jan 1, 2007

By Tracy Brettmann, Shailendra Endley, Jason Leary, Shashank Valluru

"Augered Cast-in-Place (ACIP) piles have long been used for deep foundation support in sands due to their high capacity and speed of installation. Very little information exists on the effects on capacity if the auger needs to be withdrawn from the hole prior to grouting. This condition can occur due to various reasons including grout plug ups, equipment issues, and grout supply delivery problems. It can become a major problem for the project team if this happens during production because the capacity of that pile is then in question, potentially resulting in re-design, installation of replacement piles and/or schedule delays. This paper compares the results of two high capacity test piles installed into a dense sand where one test pile was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth and the other test pile was installed utilizing conventional industry standard methods. Identical load tests were then performed on both piles to compare the effects of the two different installation procedures. The load test results were surprisingly similar in this case although the grout take required for the test pile installed in the pre-drilled hole was significantly higher to produce a similar grout return depth.IntroductionAugered Cast-in-Place (ACIP) piles are used extensively along the Texas Gulf Coast due to their combination of high capacity and speed of installation resulting in one of the most cost effective deep foundation systems relative to other options. Soil conditions in this region typically consist of alternating layers of sand and clay in the upper several hundred feet. ACIP piles are routinely installed to depths of over 100-ft to achieve the required capacity depending on the site specific soil conditions and therefore typically extend through and tip into sand layers. Occasionally, due to various reasons like equipment issues and plug-ups, the auger is withdrawn from the hole without grouting. Significant sand in the soil profile could lead to questions about the effect of the auger withdrawal on the pile capacity and load deflection relationship.This paper summarizes the results of two identical pile load tests performed on adjacent piles of the same length with the main difference being one was installed using the standard installation procedure and the other was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth. The load test results were then evaluated using load transfer analyses to estimate the effect of the withdrawal of the auger on the load-deflection characteristics and capacity."

Jan 1, 2017

By L. H. Banning

Recent dry-top electric smelting tests at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., indicate that a high-titanium slag and a good grade of pig iron can be produced from alluvial Idaho ilmenite. A total of 120 tons of concentrates were smelted during this investigation, to yield an average of 0.5 ton of slag and 0.3 ton of pig iron per ton of ilmenite. Power consumption averaged 1,400 kv.-hr. per ton of ilmenite, at a feed rate of 400 to 500 pounds per hour, when operating at an electrical energy input of 290 to 370 kilowatts. The optimum operating voltage appeared to be 110 volts, phase-to-phase. Graphite electrode consumption averaged 15.6 pounds per ton of ilmenite smelted. Magnesite furnace refractory withstood the corrosive action of the hot metal and slag better than carbon refractory.

Jan 1, 1955

By L. H. McGuire, L. B. Berger

"During the period October 31 to November 4, 1944, tests were conducted by the Bureau of Mines in the Cascade Tunnel of the Great Northern Railway Cc. to determine the effects upon the tunnel atmosphere of the use of a Diesel freight locomotive through the tunnel. These tests were conducted at the request of the company to ascertain whether undesirable conditions might be caused by the discharge of Diesel engine exhaust gas in the tunnel, which was constructed for an electric haulage system and is not provided with equipment for mechanical ventilation. The use of Diesel locomotives on the division that includes the Cascade Tunnel was under consideration as a means of augmenting haulage facilities for the abnormal freight tonnage that must be handled during wartime.As the Bureau of Mines has received requests for information on the extent of contamination of the air of railroad tunnels by Diesel locomotives, this report was prepared to make available for general information the data obtained during the tests in the Cascade Tunnel. As the test locomotive is of a type used on other railroads, and as the bore and grade of the tunnel and the tonnages moved are comparable to such factors on other roads, the data should be sufficiently representative to be of general interest. The exceptional length of the Cascade Tunnel made it an excellent location for obtaining information on the composition of the tunnel air and on the movement of air induced in the tunnel by the passage of trains.The writers are indebted to C. O. Jenks, vice president of the Great Northern Railway Co., who arranged for the tests, and to the following personnel of the railroad who cooperated in the conduct of the tests: I. E. Clary, superintendent, Spokane Division, J. L. Robson, superintendent of motive power, oil and gas equipment, J. F. N. Gaynor, superintendent of electric operations, William Lowney, master mechanic, Spokane Division, and D. F. Marston and Verne Nelson, assistant superintendents of electric operations.The Cascade Tunnel is on the Spokane Division of the Great Northern Railway and pierces the Cascade Mountains some 49 miles west of Wenatchee, Wash. The west end of this division is electrified from Appleyard Station, 2 miles east of Wenatchee, to Skykomish, Wash., a distance of 73 miles. Until the described tests, only electric haulage had been employed through the tunnel since it was first opened to traffic in January 1929.The Cascade is the longest railroad tunnel in the United States - 7.79 miles. The tunnel is single-track, perfectly straight, concrete-lined, and is on an essentially uniform grade of 1.56 percent, ascending from west to east. The cross-sectional area of the tunnel is 314 square feet, the dimensions being shown in figure 1. Elevation of the east portal is 2,880 feet and of the west portal, 2,240 feet."

Jun 1, 1946

By P. E. Davidson

The management of solid waste is known to be a large and increasing problem in high-population areas throughout the world. It is not necessary here to add further definition to the nature and magnitude of the problem. Instead, it is the purpose of this paper to describe a new process, called the Andco-Torrax System, which will be of use in converting municipal solid waste into useful energy forms and a granulated slag by-product. The paper includes a description of the first commercial plant for the process.

Jan 1, 1977

By J. C. D. Gush

Paper written on project work carried out in partial fulfilment of Laboratory-scale testwork was undertaken to recover oxidic copper-cobalt minerals by froth flotation, which requires maintaining a certain sulphide level in the pulp. To improve control of the sulphide concentration, an electronic closed-loop system was designed that responds to the potential output of an ion-selective electrode. The PID control was improved by adding a pre-emptive control and a self-calibration feature; a data logging facility is also included. An inexpensive valve design was incorporated using locally available parts. The operating results of this control design are presented.

Jan 1, 2005

By Zolfan F. Oszter

As exploration for new mineral deposits advances farther into the Canadian North, the more the design engineer is faced with the problems of cold weather conditions. This is especially true when designing belt conveyor systems for open-pit operations where the temperature in the winter may go to -40°F or below. Problems with the mechanical components and also with the belting will arise, which in turn may reduce the availability of the system. This paper outlines the problems encountered during cold weather operation and what precautionary measures must be taken into consideration in the design of equipment, as well as in the selection of materials, in order to ensure a system which will maintain production. THE conveying of ore and waste in the pit or to the processing plant poses problems during cold weather, when temperatures may drop to -4o?F or be-low. Troubles with the mechanical components, the belting or the supporting structure may arise, and this, in turn, will reduce the availability of the conveying system.

Jan 1, 1965

By D. A. Huggins

Column flotation is finding increasing use in the flotation of copper, molybdenum and other heavy metals and coal. Columns have proven operational, cost and metallurgical advantages which caused us to investigate their use in the proposed Escondida flowsheet. A comparative pilot plant test with 35 tons of ore showed that one column can replace three stages of cleaning and result in a significantly higher concentrate grade with no loss in recovery.

Jan 1, 1987

By Loris S. Pascoli

The increased pace of globalization in the mining industry has presented more opportunities for Canadian service companies to participate in ventures abroad. However, varying cultures, laws, competitive environments and contracting philosophies in other countries make it impossible to take for granted what is normal in the Canadian context. The author discusses some of his experiences and situations encountered in over 30 years in the diamond drilling industry, the last third of which were primarily focused on projects outside of this country.

May 1, 2001

By Helênio Resende Silva Júnior

Arcelor Mittal Asturias coking plant at Gijon works, Spain, is undergoing a complete modernization of the whole coke making complex. In this context, Gijon has to be considered a brownfield project, where Paul Wurth has been awarded with the engineering, supply of key equipment as well as erection and commissioning supervision services for the rebuild of two coke oven batteries the modernization of the adjacent by-product and relevant waste water treatment plants. Main objective of this paper is to present the technological improvements introduced by Paul Wurth in the rebuild of a modern plant focusing on fulfilling all the recent environmental regulations.

Oct 30, 2017

By B. W. Naugle

The Bureau of Mines investigated the changes that occur in decomposition products when coal is carbonized in a fluidized bed with steam as the fluidizing medium and the vapors are subsequently cracked without condensation in a fluidized bed of high-temperature coke. The coal used was from the High Splint bed, High Splint mine, Harlan County, Ky. Since this coal is agglomerating, it was blended with char. The integrated unit used in this investigation consisted of a 3-inch-diameter fluidized coal carbonizer, a 3.5-inch-diameter cracker containing a bed of high-temperature coke fluidized by the tar vapors and steam from the carbonizer, and gas-cleaning and product-recovery systems. The carbonizer was operated at 485° C and the cracker at 600°, 700°, and 800° C. The process variables investigated were temperature, residence time, and concentration (pound of tar vapors per pound of steam to the cracker) of tar vapors in the cracker. The total tar yields decreased as the temperature of the cracker increased, and at a constant cracker temperature of 600° C the yield of paraffins, acids, aromatics, and olefins in the distillate increased directly with the tar vapor concentration in the cracker. At 700° and 800° C only the acids and aromatics increased with increased concentration. Bases remained essentially constant regardless of the temperature and concentration. Similar results were obtained when the tar from the carbonizer was condensed prior to feeding to the cracker.

Jan 1, 1965

By M.P. ROY, ASHISH K. VISHWAKARMA, A.K. MISHRA, P.K. SINGH, VIVEK K. HIMANSHU

Principal component analysis (PCA) is one of the dimension reduction techniques widely used to classify data based on features. Ground vibration is a major hazard arising from rock blasting operations, and accurate prediction of the vibration is necessary for designing controlled blasting parameters. Most of the widely accepted predictors of ground vibration consider the maximum explosive charge weight per delay (MCPD) and distance as the parameters responsible for ground vibration, but mining sites with bigger production targets have varying geometrical parameters to suit the excavator utility. Accordingly, other blast design parameters will also have impacts on ground-vibration intensity. A blast vibration predictor considering all the blast design parameters would be complicated, and some of the parameters will have overlapping contributions to ground-vibration intensity. Data classification using PCA is a feasible solution, and regression analysis may be performed to develop predictors using the classified input data. In this study, PCA was used along with multivariate logarithmic regression to predict ground vibration, and the performance of this technique to predict ground vibration was compared with the performances of various existing empirical predictors. The evaluation suggests that the predictor with logarithmic regression followed by PCA performs better than the existing empirical predictors.

Nov 1, 2022

By G. C. He

Effects of irregularity, rough surface and aggregation of fine particles on ultrasonic attenuation are significant. The effects should be considered while predicting particle size by ultrasonic attenuation technology. The scanning electron microscope micrographs analysis also shows that particles surface is rough and irregularity. Any slurries has its fractal structure and its special fractal scale and dimension, so, effects of irregularity, rough surface and aggregation of fine particles can be de-scribed by fractal model. The discrepancies between predictions of ultrasonic attenuation based on the assumption of smooth spherical particles and data obtained from slurries of irregular particles indicated that there were different fractal structures. The ultrasonic attenuation model was modified by fractal dimensions. The result of experimental data and analogue calculation indicated that pre-dictions of the fractal modification of ultrasonic attenuation model show good agreement with experimental data. On the other hand, from the values of fractal obtained by inversely calculation, the degree of effects of irregularity, rough surface and aggregation of particles can be estimated. The positive value of fractal dimension indicates that the aggregation has the dominant effect on ultra-sonic attenuation, otherwise, the irregularity and rough surface has the dominant effect.

Jan 1, 2014

By G. Asai

The Bureau of Mines has been engaged in a program to increase the utilization of chromium by providing samples to individuals and institutions requesting chromium for research investigations. This report consists of a tabulation of the disposition of chromium samples distributed from July 1953 through June 1961; 109 requests for chromium were answered by providing chromium as electrolytic plate, powder, or wrought forms. The demand for samples reached a peak in fiscal year 1959 and declined to a relatively low level in fiscal year 1961. The largest number of requests came from individuals engaged in mechanical property studies; there were also many requests from those concerned with vaporized metal and physical properties studies. Most noteworthy application for chromium was the experimental use of the radioactive form, Cr[51], in radiotherapy of cancer.

Jan 1, 1964

By Alejandro Ferrada Vergara, María Jesús Barros Godoy

The need for a basic method for selecting explosives based on rock mass or intact rock properties for mining and construction arises from the limited consideration given to these factors when choosing among products and also an implicit overestimation of the explosive power to fragment the rock. This study highlights the importance of evaluating different properties such as rock strength, deformation, fracturing, detonation velocity and energy release when selecting explosives. The concept of characteristic impedance, which considers rock strength against shock waves generated by explosive detonation, is introduced. Understanding this concept is crucial for assessing explosive behavior according to various rock types. The study concludes with a practical guide table that categorizes rock properties and provides recommendations for selecting explosives based on rock mass and rock properties. However, it is important to consider other relevant factors, such as the presence of water or nearby instabilities, which can influence the final choice of explosives.

Jan 21, 2025

By P. Czaja

The paper presents a patented and copyright protected concept of constructing a shaft lining that goes through rock masses having strong rheological properties and being susceptible to leaching. In the case of salt layers, especially at significant depths (over 900 m) the relative convergence of the heading contour may amount to 40 ?/year. That results in the fact that any other method of securing the shaft lining, e.g. by making it flexible, will not be sufficient to ensure the stability of the shaft reinforcement geometry. In the new shaft lining concept the excessive rock creep into the outbreak inside the shaft diameter will be removed by local and controlled leaching of the shaft cheeks by means of fresh water directed through a porous medium at the contact layer behind the watertight tubing lining. The paper presents the structure of such a lining and an outline of the construction technology. In order to implement such a lining, a typical tubing will be applied. Separate design and manufacturing will be required for the technological rings used to control the leaching process behind the lining.

Aug 1, 2013

By Nozomu Kotake, Rakshya Shrestha, Ralph Griffin, Stefanos Papadopulos, Jeff Fippin, Sushil Kafle

Direct Power Compaction (DPC) is a deep Vibro-compaction method used for liquefaction mitigation. In DPC, H-beams are used as vibrating rods penetrating deep into the ground, and a vibrating force is applied directly to the tip of these H-beams to densify the loose ground. A characteristic feature of DPC is the use of a flapping plate installed at the base of the H-beam to enhance the compaction efficiency during penetration. In addition, 2-rod and 4-rod type equipment have been developed to improve productivity and enable rapid construction. DPC was selected as the most suitable and cost-effective technique to mitigate liquefaction hazards in two projects in the San Francisco Bay Area, one on Alameda Island and another on Treasure Island. Both sites were capped with hydraulically placed sand fills. Liquefaction analyses indicated excessive liquefaction-induced settlements and large lateral spread without ground improvement. Densification using DPC was performed up to depths of 42 ft to reduce the liquefaction potential of the sand fill to acceptable levels and to allow planned improvements. Cone penetration tests were conducted before and after DPC to evaluate its performance. This paper describes the equipment and process involved in DPC and discusses its application in terms of subsurface conditions and geotechnical design considerations.

Sep 8, 2021

By Raymond L. Carpenter

The thermal conductivity, electrical resistivity, and Seebeck coefficient for nine compounds, based on the formula for enargite Cu3AsS3, were measured in a search for efficient materials to be used in thermoelectric generators or refrigerators. Results indicate that one of these compounds, Cu3SbSe4, has thermoelectric properties approaching those of bismuth telluride. An investigation of the effect of adding small quantities of tellurium to Cu3SbSe4 and Cu3SbS4 in order to improve their properties also was made. A figure of merit of 2.1 x 10-4 °C-1 was obtained for Cu3SbSe4 + 0.1 percent tellurium.

Jan 1, 1963

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

By Thomas Schanz

Current steel market conditions require small investments only to lower operational cost. SMS Concast has developed new products which optimize continuous casting process cost for long product steel production. This paper describes a selection of three products. All three systems are patented (patent pending for CONDRIVE). CONSAFE, a non-radioactive mould level measurement system for reliable mould level measuring on open stream casting CCM’s; CONSTIR-MWS, an improved control software for electromagnetic stirrers which lowers energy cost by 35%; CONDRIVE, a brand new oscillation drive system which provides the features of a hydraulic oscillator, however with a cost efficient electric drive.

Aug 17, 2017