Search Documents

"The asbestos mining industry in the Eastern Townships of Quebec has early recognized the undesirable side-effects associated with mineral production, such as air pollution, noise and unsightly waste dumps. In order to efficiently achieve the industry's aim of eliminating or minimizing these objectionable features of mining, all of the asbestos producers in Quebec interchange information, knowledge and design dealing with the environmental control measures through the Environmental Committee of the Quebec Asbestos Mining Association.The paper describes what has been done and what is planned for the future in the various problem areas, such as control of dust emitted during the open-pit drilling operation, control of dryer stack emissions, control of the environment in ore, fibre and tailings handling operations, rehabilitation of the countryside covered by waste dumps, and many others."

Jan 1, 1971

By S. J. Kohut

Until recently SX-EW technology has only been used to produce conventional cathode for the cyclical commodity marketplace. Unlike electrorefining, SX-EW lends itself to the integration with the downstream manufacturing technologies for direct mine site production of value added products. The integration of SX-EW and downstream manufacturing results in the elimination of redundant process steps, the cost savings, and the access to value added product markets which can buffer the producer from swings in the cathode market. SX-EW production of copper powder and powder-based products has been demonstrated at the pilot plant level. The SX-EW process has been successfully redesigned to meet the more specific demands of engineered products. Challenges include the solution purity, the cell ventilation, the high current density operation and the product handling. Successful demonstration of mine site production of value added SX- EW products opens up new non-commodity marketplaces to the mining industry.

Jan 1, 1999

By C. Sun

With complex component, higher salt content, low biodegradability, DSD acid oxidation wastewater could not be efficiently dealt with traditional methods. It is pointed that the coal water slurry could be made with DSD acid oxidation wastewater of different concentration and the density of coal water slurry could be up to 70%, while its viscosity is only 850~930 mPa?s. The coal water slurry could be perfectly jetted and burnt under different conditions. The higher density the DSD acid oxidation wastewater has, the better properties the coal water slurry have. The pollution components and characteristic group of DSD acid oxidation wastewater are similar to the additives of coal water slurry, so it could be used as a kind of usable additive of water coal slurry. It is so reasonable and feasible to make coal water slurry with DSD acid oxidation wastewater that the pollution of DSD acid oxidation wastewater can be solved completely.

Feb 23, 2014

By N. Duda, P. Śliwiński, P. Stefaniak, B. Jachnik

Ventilation and air-conditioning are some of the most energy-consuming processes in deep underground mining. Additionally, the energy consumption of these processes systematically increases along with the expansion of the mine. Therefore, proper energy efficiency assessment and consumption forecasts of these systems are particularly important in modern mines for ongoing tracking and planning of the likely costs. In the article, a short-term prediction model for surface air–conditioning stations is described. This model takes into account dependencies that were identified, based on the data from the supervisory control and data acquisition (SCADA) systems. These dependencies between the response value and the external conditions are then incorporated into the model. This way, for example, the ambient temperature or the total number of specific days of the week (with sometimes significantly lower or higher than the weekly average energy consumption levels) are included. Taking into account these dependencies, and e.g. forecasted average monthly temperatures allow us to include the seasonality of energy consumption in the presented model. In the article, a sample energy efficiency analysis of the A/C system based on an example of the KGHM Polish Copper Polkowice-Sieroszowice mine is performed. The results of the solution proposed in the article are then evaluated, and compared to the currently functioning, more basic forecasting methods. However, given the general nature of the dependencies used in the model, similar solutions could be used in other case studies.

Sep 1, 2021

By R. Grimard, M. Gamache, L. -P. Bigras, P. Cohen

This paper describes a real-time fleet management system for an undergroun mine. Dispatching, routing and scheduling are handled simultaneously, taking into account the mine status, operational constraints and vehicle location information. Each assignment decision takes into account the traffic on the road segments of the mine network, whether road segments are bi-directional or uni-directional, and ensures that each LHD (load-haul-dump) vehicle arrives at loading and dumping points with the correct orientation. Such a system can be used either as a simulation tool for strategic planning or as a real-time managing and optimizing system for operations. In the simulation mode, the system can accurately estimate the impact on productivity of decisions such as the development of waiting areas (bays, sidings), or the addition (elimination) of vehicles to the fleet in operation. When used for real-time dispatching, routing and scheduling of vehicles, the system can optimize production with respect to various assignment criteria such as cycle-time minimization or deviation from a target production plan.

Jan 1, 2004

By D. C. Yates, G. V. Jolliffe

In the five coalfields of Staffordshire, there have been some 43 incidents of spontaneous fires and heatings which have required special attention in the past ten years. This total excludes incidents in the Thick Coal Seam of South Staffordshire, which was worked until 1967, and which was subject to an almost continuous series of heatings. The incidents have been classified to show the sites of occurrence, the contributory factors which may have caused them and the treatments applied to them. The remedial techniques, as practised in Staffordshire, are dealt with in detail, with particular reference to standard methods of stopping-off. Precautionary measures taken are described, including a "liability to spontaneous combustion" classification of all seams, and the setting up of an emergency organization with emergency stocks of materials and equipment. The paper is concluded by a few words on the organization and control at the time of an incident.

May 23, 1905

By J. B. Dilworth

I. INTRODUCTION. THE purpose of this paper is, first, to give a general account of a little-known coal-district of SE. Kentucky, its topography, drainage, and mineral resources, for those who may be interested in its economic development; and secondly, so to describe the geologic features of the field as to furnish available data to those engaged on the broader problems of Appalachian coal-geology. The data from which the major portion of the paper has been prepared were obtained, in professional investigations for private individuals and corporations, within the last decade. The area under review, defined by a heavy line on the map, Fig. 1, lies between Little Black and Pine mountains, and extends from Harlan on the west to a N-S. line crossing Looney creek 3 miles from its mouth on the east. This area can be divided for description into a Western and an Eastern Division. The character of investigation pursued in the Western Division, below Fugitt creek, was very different from that employed in the Eastern. In the former, only a rapid reconnoissance was attempted : such coal-openings as had been made by prospectors or by citizens in obtaining fuel were visited, their sections measured and, in many instances, sampled. Elevations were obtained barometrically and approximate locations sketched on a small-scale map. In a field where the coals are so well opened, the reconnoissance method gives a very fair idea of the number and character of the principal beds and their relative positions, and affords much evidence for their correlation over wide areas, without permitting the more refined work required to discover all the seams of the measures and to determine the details of geologic structure.

Feb 1, 1912

By Otis M. Clarke

The purpose of geochemical research in the Alabama copper belt is to re-evaluate geochemical prospecting methods as related to igneous and metamorphic rocks in a humid climate. It is also a correlation of laboratory research on copper mineral solubility with geochemical anomalies over known mineral deposits. Geochemical prospecting in warm humid climates involves different problems and conditions than geochemical prospecting in semiarid areas. Stems and others (1972) reported soil surveys in a humid tropical environment in Bahia, Brazil, were not effective in outlining areas of copper mineralization. Clarke (1971) reported false anomalies in lateritic soils in Alabama over mafic rocks. Bjorklund (1971) reported biogeochemical sampling in Finland was ineffective in detailed work outlining potential mineralized areas, although it may serve to indicate regional areas of high mineral potential. During this investigation, water, stream sediments, residual soil, and organic matter, mainly twigs, were collected from three known copper-mineralized areas. Samples were selected so as to cross mineralized outcrops and results were correlated with copper stability charts as reported by Silman (1958) and Schmitt (1962). The geochemical research performed in Alabama should be applicable to other humid areas. Geologic, Climatic, and Pedologic Setting The area of investigation is in the southern end of the Appalachian eugosyncline in eastern Alabama. It includes the Hatchet Creek prospect, Pyriton mining district, and Stone Hill copper mine. The copper mineralization is in calcium-rich metasediments that lie along the western flank of a high rank metamorphic belt. All three deposits are in the uplands of the Ashland Plateau section of the Piedmont physiographic province. The Hatchet Creek copper prospect (Clarke, 1963; 1971) consists of three mineralized areas that contain pyrrhotite, pyrite, and chalcopyrite in small crisscrossing veinlets.

Jan 1, 1972

By J. B. McKenzie

Since connnencing underground prcxiuction in 1979, the Ruttan Mine has been prone to secon:iacy sulphide dust explosions. Al though infrequent during the early years of prcxiuction, these occurrences did result in major damage and lost time injuries. 'As the mine exparrled and developed to further depths, sulphide dust explosions occurred on a more frequent basis. Incomplete ventilation se:rvices, required to exhaust the affected areas, caused frequent delays resulting in lower prcxiuction rates due to the time required to ventilate the affected areas of the mine. CUrrent procedures to minimize the effects of secon:iacy dust explosions evolved from practical suggestions arrl examining methcx:ls other mines have developed to cope with the problem. Procedures and regulations to protect errployees from exposure to hazards of sulphur dioxide are time consuming, expensive and counter prcxiuctive in their present fonn. This paper describes the history of secon:iacy sulphide dust explosions at the Ruttan Mine and the methcx:ls and proced.ures currently in place to minimize and contain the effects of dust explosions.

May 11, 1988

By Rong Fan, Roger Smart, Ning Xu

As part of an Australian Research Council project with Newmont and Newcrest mining companies studying the influence of clay minerals on rheology, hydrodynamics and flotation response, the cryo-SEM technique has been used to capture and image the clay (low crystallinity kaolinite Q38) aggregate structures in the flotation pulp immediately after collector and before frother addition. Samples were also collected from the earliest froth phase and the froth overflow corresponding to early and later concentrates. In this technique, a copper tube is filled with the sample during operation of the cell. The tube is immediately plunged into liquid nitrogen vitrifying the water phase before it can crystallise as ice thereby retaining the structures without volume or other physical change. After sublimation of the vitrified water surface, the aggregate structures are revealed and can be compared between pulp and froth phases from clays in different feeds and flotation conditions. The images from both low-clay ore and ore with clay content reveal various levels of aggregation as predominantly edge-edge connected aggregates similar to those found in our previous studies of high-clay tailings. For the samples from the ore with clay content, more extensive edge-edge clay strings are found in the early froth phase as compared to exiting froth overflow and the pulp phase with short edge-edge connected strings. It is suggested that the strings of clay particles result from edge-edge aggregation in the Plateau borders of the bubbles before breakage during sampling and the more extensive edge-edge aggregation in early froth phase is induced by crowding in the bubble borders. The clay strings collected into the overflow concentrate are almost all broken up compared with the Froth before drop-back. The implications for entrainment and entrapment mechanisms of gangue capture in froth will be discussed.

Jan 1, 2014

By A P. Powell

This paper deals with the power plant at Cassiar Asbestos Corporation Ltd., Cassiar, B.C. It discusses the units installed in the plant, the distribution of power and the costs involved. The efficiencies and economics of this power plant are considered to be somewhat better than average. Introduction C ASSIAR Asbestos Corporation's power plant had its inception in 1952 with a 15-by 15-ft. log cabin containing two International Harvester diesel generator sets of 50 kw. total generating capacity. Over the years, it has grown to its present size -an 80 by 82 ft. by 35-ft.-high rigid-frame Butler building housing eight 2,300-volt diesel generating sets, a 2,300-volt distributing switchboard, a 550-volt auxiliary panel, three air compressors, six heat exchangers and other related equipment. The units in the power plant, numbered according to their order of placement, are rated as shown in Table I. The total generating capacity of the plant is 3,673 kw. All of the generators are of the open vertical design except that on No. 7 engine,

Jan 1, 1965

By Harry H. Peek

Artesian pressures of unusual magnitude occur in the deeper aquifer units beneath a considerable part of southeastern North Carolina and extend into South Carolina. The high pressures were first observed in 1968 in wells near Wilmington that were drilled to "basement" rock and which were screened between depths of about 260 to 300 m (meters). The pressure was recognized by Peek and Heath1 as an anomalous geo-pressure and unrelated to recharge conditions in the region. Since 1973, much new information has been obtained on hydro-geologic conditions in the area and a preliminary report on the deep artesian pressures was published in 1975.2 Most of the basic information has been obtained from groundwater research stations constructed by the Groundwater Section of the North Carolina Department of Natural and Economic Resources as a part of Ground-water studies in the Coastal Plain Region. These stations consist of an exploratory well drilled to basement rock with wells completed in each principal aquifer unit to provide data on aquifer characterestics, water levels and water quality.

Jan 1, 1977

By W. M. Zeng

A mixed culture of moderately thermophilic microorganisms was enriched from Acid Mine Drainage (AMD) samples collected from several chalcopyrite mines in China,which can leach copper from chalcopyrite effectively. Its tolerance to chalcopyrite was brought up to 80 g/L after being adapted to gradually increased concentrations of chalcopyrite. The effects of several leaching variables on copper recovery in Stirred Tank Reactor had been investigated. The ore contained chalcopyrite (62.2%) and galena (25.6%) as the main sulfide minerals. The results of the tests show that it is possible, operating at 8% of pulp density to attain copper extraction of 75% in 44 days. The leaching rate of chalcopyrite tends to increase with the dissolution of total iron. Microscopic counts of microorganisms in the solution tend to be higher at low pH range. Furthermore, the analyses of leached residues indicate that the passivation of this chalcopyrite is mainly due to the formation of a mass of jarosite and anglesite (about 48.3% and 21.7% in residue respectively), other than elemental sulphur layer. The bacterial community composition was analyzed by using amplified ribosomal DNA restriction analysis (ARDRA). Two moderately thermophilic bacteria species were identified as Leptospi-rillum ferriphilum and Acidithiobacillus caldus, with different proportion in the bio-pulp, 67% and 33%, respectively.

Jan 1, 2014

By K Haga, G Danha, A Shibayama, L L. Godirilwe

The hydrometallurgical separation and enrichment processes provide an effective way to selectively recover metals from relatively dilute multicomponent sulfuric acid leach solutions. The multicomponent leach solution utilised in this study contained 0.3 g/L Cu, 0.34 g/L Ni, 0.13 g/L Co, and 2.96 g/L Fe, which was obtained after high-pressure oxidative acid leaching (HPOAL) of the copper-nickel smelter slag. The solvent extraction (SX), precipitation, and xanthate complexation processes were employed to recover and upgrade Cu, Ni, and Co from the leach solution. Batch SX tests were carried out using a countercurrent two-stage mixer settler extraction column, and LIX 984N (10 per cent v/v) as a copper extractant. Fundamental parameters influencing the extraction process such as pH, mixing speed, H2SO4 concentration, and organic/aqueous (O/A) phase ratio were investigated. For copper enrichment in solution, a combination of two extraction stages and two stripping stages were employed. Copper was successively separated from Fe, Ni, and Co under optimised extraction conditions (pH 2, 400 rev/min, O/A 0.25, and 20 min contacting) and stripping conditions (175 g/L H2SO4, 400 rev/min, O/A 4, and 20 min contacting). About 97 per cent of copper was extracted with low co-extraction of Fe, Ni, and Co of about 5.90 per cent, 1.47 per cent, and 2.53 per cent, correspondingly. A final Cu-rich solution containing 23 g/L Cu was obtained with a very low Fe concentration of 0.05 g/L. Additionally, for iron removal from the Ni/Co raffinate solution, more than 99 per cent of iron was precipitated at pH 4 by the addition of a calcium carbonate (CaCO3) suspension, with low co-precipitation of nickel and cobalt of around 3.68 per cent and 2.27 per cent, respectively. Furthermore, about 83.6 per cent of nickel and 99.4 per cent cobalt were co-precipitated from the solution by potassium amyl xanthate (PAX) solution at pH 6. The Ni and Co xanthate complexes were thermally decomposed and recovered as cobalt oxide (CoO) and nickel sulfide (NiS) solids.

Aug 24, 2022

By Emma Arakelova

An increase in concentration of a Zn-containing volatile complex for synthesis of ZnO films was investigated when processing their target by ultraviolet radiation emitted by mercury lamp. The experiments were carried out using a flow-type quartz reactor. ZnO tableted target was preliminarily irradiated during 2 to 7 hours. H2O2 (98%) vapor at 25Pa passed through the reactor with ZnO target at 373K. As substrate material, five subsequent quartz cylinders were used at 423K. The experiment lasts 4 hours. H2O2 decomposition on ZnO surface was accompanied by formation of a Zn-containing volatile complex which passed in gas phase and decomposed on the substrates with isolation of final ZnO. The concentration of the Zn-containing volatile complex (N) in gas phase increases with UV pre-irradiation time (t) (without irradiation N = 1.05 1011 particles/cm3; after t=2 hours, N = 5.19 1011 particles/cm3, after t=4 hours, N = 9.95 1011 particles/cm3; after t=7 hours, N = 1.86 1012 particles/cm3.

Jan 1, 2006

By Luben Savov

This paper presents recent research works on the removal of the tramp elements Cu, Sn, Zn and Pb from steel. The evaporation of Cu and Sn in iron-based melts treated at reduced pressure of the gas phase was studied in a vacuum induction melting furnace. The effect of chamber pressure, temperature and melt composition was investigated. Since the main source of contamination of steel with Sn and Zn is the recycling of tinplate and zinc coated steel, respectively, possibilities for the removal of meta1ic coatings in a scrap pre-treatment stage were studied, too. Tin was removed in the temperature range 400-5S0°C by treatment with reactive gases featuring high sulphur potential. Zinc can be removed by evaporation or by a combination of thermal and mechanical treatment. The paper discusses the thermodynamics of Pb in carbon-saturated iron melts, too.

Jan 1, 2001

By Robert Roby

The Mouat copper-nickel deposit in Stillwater County, south-central Montana, was examined by Paul T. Allsman, an engineer of the Bureau of Mines, in 1939. Because of the strategic importance of nickel, a project was executed by John East, Jr., J. J. Naughton, and E. W. Newman, engineers of the Bureau, to further delimit some of the copper-nickel sulfide-bearing bodies that had been discovered by the Anaconda Copper Mining. Co. in 1937 and to investigate the central part of the deposit, which had not been drilled previously. This report is based largely upon the results of the. Bureau of Mines investigation and the results of exploration by the Anaconda Copper Mining Co. In addition, a brief description is given of some other copper-nickel sulfide-bearing deposits along tho Stillwater Complex.

Jan 1, 1949

By H. J. Heinen

The Bureau of Mines, investigated a cyanidation-carbon adsorption technique for extracting gold from arsenopyrite concentrates. Agitation leach experiments were conducted on 85-pct-minus-35-mesh gravity concentrates containing 21.8 oz gold and 6.4 oz silver per ton. Results obtained in leaching the concentrates showed that 96.9 pct gold and 90.7 pct silver extraction could be achieved in 96 hours of agitation. Gold and silver were recovered from the resulting pregnant solution by exposure to granular activated carbon in a countercurrent system. Carbon loadings of 2,556 oz of gold and 502 oz of silver per ton were achieved. These loadings are significantly higher than heretofore thought practical.

Jan 1, 1980

By R. Heikkilä

In this paper the utilisation of building information models (BIM) and construction automation on building sites is discussed. A lot of research has been carried out to develop new applications for using BIM to assist construction site planning, different operations and logistics. The methods of production control and management on site utilize BIM together with machine control and navigation systems. In Finland machine control systems and the automation of construction equipment is widely used in infrastructure construction. Recently similar methods have been introduced also in building construction. This paper describes some latest Finnish examples where BIM-software is used for the planning, execution and control of building construction operations. University of Oulu has studied methods and technologies to capitalize BIM-models. The research has been mainly in infrastructure construction but the activities have recently been extended to building construction. In this paper a BIM-based tower crane operation and control system is discussed as a case study. The aim of this study was to highlight the potential areas were automation can increase the crane productivity and improve site operations and logistics. The construction site managers and tower crane operators interviewed in this study were experienced in using BIM-models on site.

Aug 1, 2013

By Pascal Lesagel

Life Cycle Assessment (LCA) is a holistic environmental assessment tool that allows the compilation and evaluation of the inputs, outputs, and potential environmental impacts of a product or service throughout its life cycle, from cradle to grave (i.e., from resource extraction and transformation to final disposal, including production and use stages). The relevance of LCA for the mining industry is twofold. First, the mining industry has a role in providing the LCA community the data that allows subsequent evaluations of the life cycle environmental impacts of primary materials such as metals, as well as the environmental comparison of the downstream products of the mining industry with other competing materials for specific uses. Second, the mining industry can use LCA in order to evaluate the environmental impacts of its activities, identify their environmental hotspots and compare the impacts of available technical options. For example, the environmental impacts of different extractive and processing technology can be compared through the use of LCA. This latter use of LCA by the mining industry is less common. This paper discusses the use of LCA to compare sulphidic tailings management options. The paper also presents some of the LCA research challenges that still have to be addressed to increase the relevance of LCA results for the specific context of mining activities.

Nov 1, 2008