Search Documents

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By P Fuller, A R. Penney

Re-commencement of mining in the Western Zone of Beaconsfield Gold Mine following a seismically-induced rockfall fatality in April 2006 required a change of mining method involving drilling and blasting from specially developed drives in the footwall of the orebody. Broken ore is mucked remotely from ore drives on each level. Support in the footwall drives is required to maintain stability during their development and as stopes are retreated, which increases induced stresses and further seismic events are triggered. The paper outlines the challenges involved and methods used to select the footwall drive support to handle both static and dynamic load demand. The importance of load development in the support system, its displacement capacity, the compatibility of support elements and energy absorption capacity of the support system are highlighted. It is usual in any support selection process to ensure that capacity exceeds demand to create a factor of safety. In this case the demands on the system relate to load, displacement and energy absorption and the support system capacity for each must ensure that appropriate factors of safety for each are achieved. The paper shows how these factors are not independent and that selecting a high factor of safety for load can lead to compatibility problems with support elements in the support system.

Jan 1, 2008

By P. M. Pearson

This paper describes the principles ()f systems engineering and their application to the various transport problems confronting the mining industry. The organization of mining operations into sub-system design problems is explained.

Jan 1, 1970

The Sandvik DE710 diamond core drill has become one of the most popular exploration drills available. It is operated on exploration and mining projects in locations around the world. The compact nature of the DE710 allows a small footprint on site. This has proven to be a great benefit in difficult access areas where site preparation can be limited. The DE710 drill is available in a range of con-figurations to suit global operational and environ-mental demands. It can be truck-mounted for greater maneuverability and ease of relocating the drill between sites. The drill can also be fitted to crawler tracks, powered from the rig hydraulic system, making it a small, self-propelled unit for areas with difficult site access. And the DE710 is available in a shack-mounted configuration for cold weather applications, ensuring a protected working environment for the drill crew. The DE710 is powered by a 6.7-liter engine that produces 141 kW (190 hp) at 2,200 rpm to power the rig hydraulic system. The engine complies with the Tier 3 emissions standards that are being introduced in many countries. The hydraulic system design for the Sandvik DE710 is based on the company?s philosophy of selecting the best available products to suit the application. The main hydraulic pumps and motors are the variable displacement design. This allows for greater fl exibility and precise control of critical drilling functions. The cooling system has also been designed for operation in ambient temperatures up to 50° C (122° F) to cope with varying global operational demands.

Jan 1, 2009

By C. Maltesh

Anionic conditioning of phosphate ores prior to fatty acid flotation is a very critical step that determines the eventual selectivity, recovery and hence the economics of the process. However the chemical mechanisms operating during this conditioning step are not established. Several studies have been conducted in the past to determine the mode of interaction of collectors with the phosphate fractions however these have been done on a laboratory scale using pure phosphate minerals. In order to test the relevance of the observed effects to plant practice in this work a comprehensive survey of plant practice was first conducted and then adsorption on flotation feed and francolite were studied under simulated plant conditions. Effects of conditioning energy and water chemistry as well as solids loading and fuel oil were determined. Most importantly, different adsorption mechanisms were found to be dominant under laboratory and plant conditions. In plant water, there was some physisorption of oleic acid on phosphate flotation feed and francolite in addition to chemisorption. However, in distilled water under laboratory conditions only chemisorption was detected. Fuel oil reduced the residual oleic acid in solution after adsorption, which explains the beneficial role of extender in phosphate flotation. The dissolved species in solution arising from the flotation feed or plant processing water are shown to clearly play a major role in determining the adsorption of oleic acid on the substrates. The study also specifically demonstrates the importance of conducting research tests under plant mixing conditions and plant water chemistry for the results to be useful commercially.

Jan 1, 1996

By Harold G. Moulton

IT is highly significant that engineers should seriously consider the interrelations of technology, economics, and government. It is indicative of the emergence of maladjustments and problems that perplex our thinking and frustrate our activities. Instead of a world in which scientific discoveries and their applications through engineering to the processes of wealth production are regarded as the royal road to progress, we now find science and engineering being made responsible, in no small degree, for our economic and social troubles; and the powers of government are even being invoked to stem the tidal wave of technology. Indeed, there is a deep-seated fear, manifested in the writings of some of our greatest scientists as well as in popular discussions, that science may destroy our civilization.

Jan 1, 1938

By Christopher R. Lattanzi

"Discounted cash flow analysis provides a means of relating the magnitude of expected future cash profits to the magnitude of the initial cash investment required to purchase an asset or to develop it for commercial production. The objectives of discounted cash flow analysis are to determine:.. The net present value of a stream of expected future cash revenues and expenditures... The rate of return which the expected future cash flows will yield on a given level of initial cash investment.In the case of mineral properties, discounted cash flow analysis is generally accepted as the preferred method of valuation, whenever sufficient data are available to permit its reasoned application. Sufficient data are required to support estimation of all of the individual elements of cash revenue and cash expenditure which will be associated with the development and operation of the property, up to the end of its estimated life. It is the accuracy of these input estimates which determines the validity of the resulting determinations of profitability and rate of return on invested capital.In undertaking any discounted cash flow analysis, it is important to recognize certain fundamental attributes of the mining industty:.. The basis of any mineral development is the existence of an ore reserve... Costs are determined by the number of tonnes mined and processed, while revenues are determined by the number of pounds or ounces of metal produced. The two are related by the recovered grade of the ore... Profit is typically more sensitive to changes in revenue than it is to changes in cost... Commodity price is a principal determinant of revenue, but it is also the factor with which is associated the greatest level of financial risk.In the end, of all of the factors which must be considered in the discounted cash flow valuation of a mineral property, the most significant are the reliability of the reserve estimate, particularly with respect to recovered grade, the price at which the product is to be sold, and the risk of not maintaining the projected level of price."

Jan 1, 2003

By H Arvidson, V Chamberlain, R Marinho, B Parsons, T Rowl, M Noppé, M Mattera

With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.

May 24, 2023

By Elizabeth A. Johnson

Minor-element behavior and interaction in the copper matte-iron silicate slag system have been studied by the Bureau of Mines. In the present work, the possibility of interactions among the minor elements As, Sb, Bi, Se, and Te was investigated. Equilibrations of matte, slag, and one of each of the five minor elements were performed at 1,250° C under typical matte smelting atmospheres of CO, CO2, and S02 for mattes containing 40, 50, and 60 pct Cu. Results are compared with those of a previous Bureau of Mines study in which all five minor elements were present simultaneously.

Jan 1, 1984

By A. W. Jolliffee

ANY attempt to forecast the mineral resources of a largely unknown region is hazardous and, in the case of the Northwest Territories, such a task is even more hazardous than usual. This is not merely because of the immense territory involved (over a million and a quarter square miles), only a small fraction of which has ever been explored or prospected, but also be-cause both the geology and mineral deposits thus far examined show many unique features, and, finally, because the region is being actively prospected at the present time. However, in view of the present widespread interest in Canada's mineral resources, a brief compilation of what is known regarding mineral occurrences and geology in the explored parts of the far north seems timely. From these assembled data, a few inferences are warranted as to future mineral production from this region. HISTORY The story of mineral discovery in the Canadian northwest is a fascinating one. As well, it abundantly illustrates the importance of mineral occurrences in indicating future mining possibilities. The same sequence of events has repeated itself too often to be merely fortuitous.? In most cases, the dis-covery of a mineral deposit of possible economic value has been foreshadowed by the finding of the valuable mineral or an associated mineral in the same district, generally in small quantity, by an early explorer or traveller. Thus, John Franklin reported oil seepages from the base of Bear Rock, near Nor-man, at almost the very spot where oil was struck nearly one hundred years later. Again, some would-be Klondikers, deterred by the hardships of the route, remained to prospect around Great Slave lake, and were the first to report the Pine Point lead-zinc occurrences there and the gold-bearing veins on Yellowknife bay. Sporadic prospecting followed at the latter locality for over thirty years before the recent rich strikes were made. Similarly, in 1847, Dr. John Rae picked up a boulder of copper ore south of Rankin inlet, on Hudson bay. More than eighty years later, a body of copper-nickel sulphides carrying values in platinum metals was found at this locality. Also, the report of cobalt bloom on the east coast of Great Bear lake brought back by a Geological Survey of Canada party in 1900 was a factor in the events leading to the discovery of silver and radium there in 1930.

Jan 1, 1937

By Martin J. Gavin

During the recent study of lubricating oils carried on in the San Francisco laboratory of the United States Bureau of Mines, it became desirable to distill the oils used in the experimental work at pressures as low as 10 millimeters (mercury column) absolute. In the effort to Overcome difficulties and eliminate sources of error, certain changes were made in the apparatus for vacuum distillation used by the Bureau of Mines for crude petroleum.4 These changes were described in R.I. 2819, issued in July, 1927. Subsequent to the publication of R.I. 2819 several other changes have been made, and the present form of the apparatus for vacuum distillation of lubricating oils is described in this revision of R.I. 2819. These changes were found to give more accurate checks on duplicate distillations. The major part of the credit for the laboratory work which developed the changes in the apparatus and method revised herein is due to Boyd Guthrie, assistant petroleum chemist, and R. V. Higgins, junior chemist, o the San Francisco laboratory, United States Bureau of Mines. DESCRIPTION OF APPARATUS The distilling flask employed is essentially the Hempel flask as used by the United States Bureau of Mines for the analytical distillation of petroleum.5 he complete apparatus is shown in Figure 1. The fractionating column and exposed portion of the flask is wrapped with 4 inch asbestos rope and then surrounded by a cylindrical hood of 1/8 inch pliable asbestos sheet with a narrow air space between the wrapping and the cylindrical hood. This was found necessary to prevent any radiation or convection heat losses from the column, and resulted in obtaining a more even and constant fractionation by eliminating any dephlegmating action caused by temperature changes around the column.

Jan 1, 1930

By M. A. van Nierop

Load behaviour in an industrial mill has been measured directly by inserting probes through liner bolts. The data from conductivity probes have indicated the presence of premature centrifuging during manipulation of the load mass. Overloading conditions were also encountered. Overloading and premature centrifuging both reduce the power drawn by the mill. These effects have been successfully modelled.

Jan 1, 1997

By Arthur L. Crawford, R. E. Head, Glen Burgener, F. E. Thackwell

"INTRODUCTION This report embodies the results of a detailed statistical microscopic examination of the ore and the mill products of the Silver King Coalition Mines Co., Park City, Utah.The study was conducted under the joint auspices of the United States Bureau of mines is cooperation with the University of Utah at Salt Lake City, Utah. The work was done in the cooperative Microscopic Service Laboratory, which was equipped by contributions from the following companies: Utah Copper Co., International Smelting & Refining Co., American Smelting & Refining Co., United States Smelting, Refining & Mining Co., Tintic Standard Mining Co., Silver King Coalition Mines Co., and Park Utah Consolidated Mines Co. The salaries and the other costs involved in operation of the laboratory were met by contributions from certain supporting companies. In addition to the regular personnel of the laboratory the Bureau of Mines contributed the part-time services of a microscopist-consultant to direct and assist with the technical work.ACKNOWLEDGEMENTSThe authors acknowledge the courtesies extended by the Silver King Coalition Mines Co., through its general manager, M. J. Dailey, in furnishing the various ores and products on which the study was made, together with general information concerning the problems encountered or recognized in connection with the milling of the Silver King ore."

Jun 1, 1934

By T Purvis, J Calverd, A-K Greve

The Ernest Henry Mining (EHM) underground mine is situated adjacent to the Great Artesian Basin in North Queensland and within a fracture zone. Underground development commenced in February 2008 and has extended to approximately 1000 vertical metres below the surface.Groundwater has been encountered in numerous locations throughout the mine, predominantly on the eastern side of the orebody and often related to fault structures. Most of the groundwater encountered has been managed with conventional pumping systems; however, on occasions large water inflows have been encountered, which have had a significant impact on the planned development of the mine. Some of the intersections encountered had the potential to compromise the mine from a combination of high temperature (over 45°C), high pressure (3500 kPa) and high flows (50–100 L/s).This paper describes three case studies where significant water inflows were encountered and then controlled by the injection of cementitious grout into the rock mass. The case studies are the 1650 mid-shaft heading, the 1325 shaft access decline and the 1625 to 1475 fresh air rise (FAR) raise bore. Each case study includes a brief description of the event that occurred and the grouting equipment and techniques developed to enable mining to continue.The paper also describes the development of a hydrogeological map of the mine, the probe-hole regime used for high-risk headings and the required processes and systems to inject both cementitious grouts and polyurethane resin into the rock mass.CITATION:Purvis, T, Calverd, J and Greve, A-K, 2014. Management of high-pressure groundwater in underground development at Ernest Henry Mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 217–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By A. D. Huffman

This paper covers the major salt deposits of Canada, with a brief summary of the early history of the industry and a more extended outline of progress since the second world war. Both dry mining and solution mining are covered, and the future of salt mining in Canada is discussed.

Jan 1, 1968

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2017

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2018

By C. R. Kato, G. Proulx

"Within the continuous scenario of reduced aluminium price and plants production costs increase, the energy consumption optimization in the aluminum electrolytic pots continues as the main focus for the producers. Energy consumption was chosen as a key performance indicator to drive the efforts and actions for improvements. Alcoa improved the energy consumption by approximately 3% from 2005 to 2015. This improvement was a result of best practices implementation, new technologies introduction, strategic actions with plant curtailments and management practices. The main objective of this paper is to highlight the importance of the management practices for planning and operational improvements beyond the technology changes. About 10 years ago, Alcoa reorganized its approach to retain knowledge in the Smelters by using a Best Practices format. For each specific subject, a skilled team defined the minimum requirements and the Best Practices for several aspects of operation and maintenance, which affect the environment, safety, cost, customers and performance. These Best Practices were deployed to all Smelters combined with training sessions to process and operation professionals. We will describe how the Best Practices were organized, the deployment strategy used, and the approach to measure the plants’ success. We will describe the management approach that includes Manufacturing Analyses focused on 3-year potential, annual planning, and weekly monitoring of plant stability. A manufacturing analysis is organized at select plants with cross-functional participation of specialists from technical, operational, procurement and finance. The output of a manufacturing analysis includes a roadmap of enablers to improve energy efficiency. A quarterly follow-up of enabler deployment is held with the plant and resources that participated in the analysis. Annually, there is a Planning Process where energy consumption enablers are selected to be implemented during the next 3 years for each plant. A monthly critical analysis is made by the plants with regional best practice support. On a weekly basis, key performance indicators are reviewed with determination of a stability index for each plant. Any deviation signal of unstable condition is alerted and supporting resources are diverted to the plant to reverse trend with countermeasures.INTRODUCTIONDue to factors like excess aluminum in the market and lower consumption in China, the LME price is declining along the last years, as showed in Figure 1. In 2011, the price peaked at US$ 2,400/ton and since then, continues to trend down and approaching the lowest level at US$ 1,500/ton in the last 5 years."

Jan 1, 2016

By Francis J. Kiessling

Energy and the conversion of potential energy into alternate forms is becoming a topic of household conversation for a larger segment of the world's population as mankind's desire for products derived from the vast array of technological developments continues to expand. The world's use of steel and the high energy consumption related to the production of steel promotes an awareness of the limitations of existing technology and a search for more economical alternates. Terminology such as (BF) Blast Furnace, (BOP) Basic Oxygen Furnace, (EAF) Electric ARC Furnace, (DR) Direct Reduction, (DRI) Direct Reduced Iron and (FC) form coke is becoming commonplace as alternates are being sought to alleviate the energy crunch. Coke production by various methods was developed as early as the seventeenth century in Europe to replace the disappearing hardwood forests that supplied the initial blast furnace fuel in the form of charcoal. In 1880, the Semet Solvay by-product coke oven design was introduced to the United States at Syracuse, New York, to supply coke for use in the production of soda ash, coke oven gas and its by products as the primary source of many organic processes. Although the Semet Solvay coke oven has not been marketed for decades, these coke oven batteries are in use today producing metallurgical coke, coke oven gas, and related by-products.

Jan 1, 1980

By Cathy Aimone-Martin, Caitlin Woznick, Brent Meins

This study is a continuation of previous work in which the responses of tall structures to close-in construction blasting at two rock excavation sites are evaluated. A total of eight buildings were instrumented to calculate blast-induced wall strains. Of these structures, five high-rise buildings measuring 166 ft (51 m) to 294 ft (90 m) in height (15 to 24 stories), were included for this study and compared with the results of previous studies that included one to three story residential structures and mid-rise structures (four to six stories). All five structures were built between 1908 and 1940 with interior walls comprising aged plaster. Three of the structures are designated Landmark, subject to a 0.5 in/s (12.7 mm/s) regulated peak particle velocity (PPV) limit. The regulated PPV limit for the two other structures was 2.0 in/s (50.8 mm/s). To date, a total of 450 close-in construction blasts have taken place over six months at the two adjacent projects, blasting three to six times per day at each site. Seismograph instrumentation included tri-axial geophones in the ground and bi-axial geophones (horizontal components only) mounted on structure exteriors at the corners closest to blasting. Peak global wall tensile strains were calculated from time-correlated differential structure displacements in two horizontal directions as measured by upper and lower geophones mounted near the roof and at street levels. Wall strains were correlated with ground excitations to establish a stiffness factor for each structure defined as the upper bound linear regression slope for strain as a function of ground displacement. In addition, a structure-specific regression best-fit function was established to relate horizontal components of displacement to velocity. These two functions were used to determine the maximum ground motion velocity for a desired limit placed on wall strain. A 25 ?-strain limit was suggested for both projects to protect interior plaster walls. To date, global wall strains have not exceeded 0.53 ?-strains (or 47 times the project limit) for peak particle velocities up to 3.49 in/s (88.6 mm/s). This demonstrates the low strain response of tall structures to ground velocities well above regulated limits. The stiffness factor computed for the most flexible high-rise building was 688 in-1 (17475 mm-1). In comparison, stiffness factors for the most flexible residential and mid-rise structures previously studied were 8651 in-1 (219735 mm-1) and 4387 in-1 (111430 mm-1), respectively. Based on a large number of measurements made at these study structures, the maximum horizontal ground velocity needed to achieve 25 ?-strains in walls ranged from 36 in/s (914 mm/s) to 192 in/s (4877 mm/s) because of the high stiffness of these buildings. Such high amplitudes of ground vibrations can never be safely achieved during close-in blasting in urban environments. These excessive values stand to show how unfounded the current limits of 0.5 in/s (12.7 mm/s) and 2.0 in/s (50.8 mm/s) are when applied to massive, tall structures. This study demonstrated that upper structure motions are highly attenuated from the lower (street-level) motions because of the long travel distances up the buildings. High-rise structures are far stiffer than mid-rise and residential structures and can withstand ground vibration amplitudes far greater than the currently enforced blasting limits in New York City.

Jan 1, 2015