Search Documents

By William Victor Vietti

A METHOD of determining the average density of the fluid column in a flowing oil well is presented. Actual field data from several wells are used to illustrate the application of the method in the Yates Field, Pecos County, Texas. The depth of the wells in the Yates Field varies from 900 to 1700 ft. depending on surface elevation and the location of the wells on structure. Production rates over 8000 bbl. hourly have been determined and many

Jan 1, 1930

By T. Bednarski, T. McCallum, L. Moya, B. Gay

"Molybdenum recovery by solvent extraction has gained interest partly due to advances in concentrate leach technology. Historically, both molybdenum and rhenium have been produced using amine-based extractants with the ability to co-extract both metals. Alternatively, a phosphinic acid-based extractant (CYANEX® 600) can be used depending on the flow sheet. CYANEX® 600 selectively extracts Mo leaving Re in the raffinate, which is a valuable feature in plants which require rejection of the rhenium from the molybdenum circuit. CYANEX® 600 piloting results are reviewed and compared to commercial experiences with an amine-based extractant. INTRODUCTION Molybdenum is most commonly found as molybdenite (MoS2) in primary porphyry deposits (about 59% of global reserves) and copper porphyries (about 39% of molybdenum reserves)[1]. Recovery from molybdenite traditionally involves flotation (concentrates typically containing 85 – 95% MoS2) followed by roasting to produce MoO3. Solvent extraction is also used to recover molybdenum from acidic aqueous solutions resulting from scrubbing of roaster and smelter off gasses and leaching of molybdenite (uranium ores). Molybdenum is also frequently found in low concentrations in copper leach inventories[2]. More recently, pressure oxidation has gained interest to treat molybdenite concentrates. Molybdenum Chemistry The chemistry of molybdenum is complex with a series of extractable species existing dependent on the pH and oxidation state as shown in Figure 1.Under strongly basic conditions, molybdenum primarily exists as MoO42- while under strongly acidic conditions MoO22+ becomes the predominant species. In between, a number of isopolymolybdates such as Mo7O246- and Mo8O264- are dominant. Equations (1) – (3) demonstrate some of the proposed molybdenum equilibrium reactions[1]."

Jan 1, 2017

By Wen Chen, Xinghua Liu, Zeyou Peng, Qiulin Wang

"Limonite is a collective for iron hydroxide argillaceous materials. It is very difficult to be treated due to the wide variation in specific gravity and magnetism and the high argillization rate in the course of grinding and beneficiation. The iron ore in Huangmei, Hubei, China is the typical representative of limonite. If the limonite is processed using conventional physical beneficiation methods (e.g. magnetic separation, gravity separation, flocculation-desliming-flotation, or a combined process of the three), it can only be obtained an iron concentrate grade of 51.98% and an iron metal recovery of 86.64%. However, the technique of flash magnetic roasting-magnetic separation can improve the concentrate grade to 61.03%, iron recovery to 91.17%. This paper describes the tests of recovering limonite by flash magnetic roasting in detail.IntroductionLimonite (mFe2O3, nH2O)[1] is a general designation for hydrous iron hydroxides and argillaceous matters. Limonite is hard to be separated because of its complicated geneses, comparatively weak magnetism, nonuniform grain size and being easily slimed during grinding. So most small and medium enterprises sell deslimed limonite product which was dealt with just by simple methods of washing, magnetic separation or gravity separation and so on. In recent years with the iron ore prices soaring, significant progress was made in mineral processing research of limonite. Laboratory research and industrial test results showed that flocculation-desliming-flotation process and roasting-magnetic separation process are the two best methods to recover limonite till now. To compare these two methods, roasting-magnetic separation process is superior to flocculation-desliming-flotation process in aspects of beneficiation indexes and industrial stability."

Jan 1, 2012

By M. Vasudevan

In sulfide mineral flotation, the efficiency of separation is severely affected by the presence of non-sulfide gangue minerals, such as altered silicates and serpentines. Although this is an acknowledged fact, most studies in mineral processing have focused on value minerals, and studies on gangue minerals affecting flotation performance are quite rare, and even those that do are limited in scope. This paper is an attempt to highlight the use of grade-recovery curves in studying the effects of gangue minerals. Specifically, we present the flotation response of problematic Ni and Cu ores which show highly uncharacteristic but similar grade-recovery characteristics despite the very different mineralogy and try to understand this behavior and the underlying mechanism. Finally, we propose chemical modifiers as solutions to overcome the detrimental effects of these gangue minerals and improve efficiency of flotation performance. Keywords: Non-sulfide gangue, grade-recovery, sulfide minerals, serpentines, talc, shale, slimes, spiking, modifiers

Sep 1, 2012

By Adriana Amaro Diacenco

Neste trabalho, os procedimentos para modelagem de estruturas de compósitos do tipo sanduíche que incorporam materiais viscoelásticos são apresentados. A análise numérica foi desenvolvida utilizando a Teoria de Deformação Cisalhante de Primeira Ordem (FSDT), que é implementada em um elemento Serendipity retangular contendo oito nós e cinco graus de liberdade. A incorporação do amortecimento para os modelos de elementos finitos em compósitos de placas laminadas é feita usando a abordagem de módulo complexo e a resolução numérica das equações resultantes do movimento são aspectos particularmente relevantes dos procedimentos de modelagem. Após as discussões de vários aspectos teóricos, as funções de resposta em frequências (FRF's) são calculadas para placas laminadas de compósitos com camada viscoelástica.

Aug 17, 2017

By G. Ergin

The interactions taking place between Al-Mg alloys and the bed media during aluminum filtration are not yet well understood. These interactions were studied using the infiltration technique. The reaction interface was analyzed using different techniques such as SEM and TEM. Only spinel formation was observed at the interface regardless of the type of alumina and contact time. This paper discusses the results of the study.

Jan 1, 2004

By Bernard Dallaire, Jean Cayouette, Sylvain Duchesne

"Louvicourt Mine's concentrator, located near Val d'Or, Quebec, treats an average of 4,300 tonnes of ore per day composed mainly of copper, zinc, gold and silver. An analysis of concentrator revenues and metallurgical losses shows a potential for additional gain, particularly in regards to precious metals (kustelite) where recovery is usually around 67 -70 %. The planning, installation and trial operational period of two Outokumpu SK-240 flash cells at the underflow of the primary cyclones took two years. The use of (( flash flotation )) technology has made it possible to exploit the favourable conditions at the underflow of the primary cyclones such as precious metal concentration and the presence of liberated coarse chalcopyrite. These conditions permit early flotation (fresh surfaces) of the kustelite and the liberated copper. Since the start-up of the flash cells, the metallurgical gains have turned out to be very positive with increases in metal recovery reflected in appreciable NSR gains. Also, significant savings in reagent consumption and a coarser copper concentrate have made it possible to reduce the drying cycle of the Larox filter presses since the cells were put into operation.BACKGROUNDLouvicourt Mine is operated by Aur Resources Inc. (30% ownership) on behalf of its partners Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corp. (25%). The mine is located in northwestern Quebec about 600 km north of Montreal and about 25 km east of the mining town of Val d'Or. The mine commenced commercial production in July 1994.The massive sulphide ore deposit lies at depths varying between 450 m and 900 m. Mining reserves (2% Cu equi. cut-off) as of Jan. Is', 2000 are estimated at 7.5 million tonnes of ore averaging 3.4% Cu, 1.8% Zn, 28.0 g/t Ag and 0.9 g/t Au. Delineated ore reserves permit the use of a mechanized transverse blasthole mining method. The extraction order is a typical 1.3.5 mining sequence. Primary and secondary stopes are 15 m wide, 15 to 70 m long (25 m long average) and 30 m high. Backfilling for pillar recovery and regional stability is required."

Jan 1, 2001

By Emmanuel N. Zevgolis

In the present work, a reduction roasting experimental study of Greek nickeliferous laterite samples with a gaseous reducing mixture ? CO:N2- is presented. The effect of parameters such as temperature, ore grain size, and composition of the reducing mixture were examined. It is deduced that the reducibility of intermediate type laterite sample, where iron appears mainly in the form of goethite (a-FeOOH), is considerably higher than that of limonitic type laterite samples, where hematite (a-Fe2O3) is the predominant iron mineral phase. The degree of reduction of the limonitic type laterite samples does not exceed 50%, while it reaches 95% in the case of the intermediate-type laterite sample under the same experimental conditions. Increasing the temperature in the range 750-900°C does not considerably favor the reduction of the limonitic type laterites, whereas decrease of ore grain size of the limonitic-type ore samples and more intense reducing conditions increase the reduction. The considerably higher specific surface area values of the intermediate laterite samples, diminishes the effect of the ore grain size and this can be regarded as the critical parameter leading to the higher reducibility of this ore.

Jan 1, 2009

By Vadim J. Jabotinski

Electron beam processing is potentially very attractive for the high temperature treatment of hazardous materials. The very high power efficiency of the electron beam energy source (80- 90% of the power from the electric power line is converted to useable energy) is one of the positive features of this technique. This paper will consider advanced electron beam concepts for solid, liquid, and gaseous waste treatment such as stabilization of radioactive solid and liquid hazardous streams. Fundamental aspects and applications including an analysis of the economic potential of electron beam processing of waste treatment will be presented.

Jan 1, 2000

Utilize innovative processing technology to prepare high-purity, ultrafine advanced ceramic powders with little or no contamination occurring during the milling process. Advanced ceramic materials made from these powders could substitute for high-temperature alloys containing critical materials such as chromium, cobalt, and nickel. Approach Modify and evaluate the Bureau's turbomill, developed earlier to grind a variety of ceramic raw materials (clay, mica, and talc), as a milling or size-reduction technique for hard and abrasive advanced ceramic powders, such as silicon carbide. Background Powders for producing ceramic materials, such as silicon carbide. silicon nitride, alumina, and zirconia, which arc being considered for use in severe applications requiring high-temperature and/or corrosion resistance, are very difficult to reduce to fine sizes for processing into finished parts. Traditional techniques of particle size reduction, such as ball milling and jet milling, are very energy intensive and/or slow. These traditional techniques often produce materials that have a nonuniform particle size distribution and are contaminated by the milling media or container.

Jan 1, 1989

By William C. McLaughlin

In the deep vein mines of the Coeur d'Alene mining district, rock bursts are a potential hazard to the mine structure and underground personnel. Damage repair costs are estimated by one company to exceed $1 per ton of ore mined. The Bureau of Mines, in cooperation with the mining companies, has conducted research intermittently over the past 10 years to help reduce bursts. Onsite inspections of major rock bursts were conducted, and reports were submitted to mine management; these included the geology and geometry of the affected area. The paper discusses the development and improvement of microseismic and surface monitoring equipment. The underground microseismic network, when operated on a regular basis and the results plotted daily, is capable of detecting stress concentration in certain areas. The surface seismographs record rock bursts, blasts, earthquakes, etc., throughout the district and show approximate location, time, and relative intensity of the event.

Jan 1, 1976

By A T. Spathis, M L. Lawlor-O’Neill

A methodology for the inversion of a scaled charge weight superposition model to predict peak particle velocity (PPV) has been examined. The inversion involves two steps: first simulated annealing is used to get an initial estimate of the model parameters; and second, these parameters are used as input to a quasi-Newton non-linear optimisation method, used to refine the value of the parameters. The methodology recovers the three required parameters (two charge weight scaling parameters and a time window width) and does this directly from a single production blast for a given point of interest. It has been tested on a synthetic example and recovered the input model parameters successfully in the presence of introduced noise with a coefficient of variation ranging up to ten per cent. Another test used the vibration measurements of three tunnel blasts monitored during the construction of the Citybanan tunnel in Stockholm. In this case, the three model parameters are found from one blast and for a given point of interest, and the PPV at the same point of interest is predicted for the second and third blast fired in the same vicinity as the first blast. The three blasts used different firing sequences. The predicted PPV limits use a confidence interval determined from the scatter in the peak levels obtained from the single calibration blast. The methodology was able to predict an upper bound for the PPV in 21 of the 26 tunnel blast vibrations studied. These predictions improve on a previous study involving the same model but which did not use the inversion process above. Given this reasonable success, further testing of the method on other data sets and alternative forward prediction models is recommended.CITATION:Lawlor-O’Neill, M L and Spathis, A T, 2015. An inversion method for the prediction of peak particle velocity in blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 97–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Lj. D. Andric

Development of modern devices for mechanical and mechanochemical materials activation has been dated since the beginning of last century. Rapid development of high-energy mills that are different in type, size, design and performances, has been occurred during the last four decades. Because of complete understanding of mechanical processing, entire knowledge of theoretical principles of high-energy mills is necessary. These principles are main causales of process that are happened in materials during the mechanical activation. This paper is occupied by theoretical principles of operation of high-energy mills. Conventional high energy mills with balls, high-energy planetary mills and high-energy vibrational mills are particularly considered in the paper.

Jan 1, 2014

By Chuck Edwards

"Cameco operates the high-grade McArthur River uranium mine in northern Saskatchewan, and is constructing the high-grade Cigar Lake uranium mine. Cameco has studied the concept of underground milling of high-grade uranium ore. Compared to conventional milling on surface, the underground milling scheme appears to offer significant cost savings and a lower environmental impact. This paper describes the underground milling scheme, presents process flowsheets and plant layouts, and provides an assessment of potential benefits from underground milling.INTRODUCTIONCameco CorporationCameco is the world’s largest uranium producer, with three operations in Saskatchewan (Rabbit Lake mine/mill, McArthur River mine, and Key Lake mill), two in the United States (Crow Butte and Smith/Highland ISL operations) and two new mines being developed in Canada (Cigar Lake project) and Kazakhstan (Inkai project). Cameco provides uranium fuel refining and conversion services at its Blind River and Port Hope facilities in Ontario. Cameco is part owner (31.6%) of Bruce Power that leases eight nuclear power plants located in southern Ontario. Cameco is the majority shareholder in Centerra Gold Inc., which operates gold mines in the Kyrgyz Republic and in Mongolia.Global Uranium Production RequirementsCentral to Cameco’s view of future uranium supply requirements is the belief that the world is experiencing a nuclear renaissance. This belief is supported by a number of developments, including:•,?Countries representing half the world’s population are now constructing new nuclear power plants. Many countries without nuclear power have begun to plan for it, seeking reliability, clean air and energy independence.•,?Accelerated growth for this industry is also becoming much more likely. In Asia, primarily in China and India, 92 reactors are under construction, on order or planned to help meet rapidly expanding economic needs. Other Asian countries, such as Vietnam and Indonesia, with large populations and rapidly growing economies, are also expected to follow.•,?In the United States the “Energy Policy Act of 2005”, the first energy legislation introduced in over a decade, was signed. This legislation includes provisions recognizing, for the first time at a national level, the clean air contribution of nuclear energy and its critical role in meeting energy security. Upon signing this landmark legislation President Bush stated, “We will start building nuclear power plants by the end of this decade.”"

Jan 1, 2007

By N. Valkanov

This paper presents results of an investigation into the connection between minerals liberation management and flotation, responding to lead-zinc concentrator ?Erma reka?, in Bulgaria. Monitoring of a Zn flotation circuit was carried out. The causes for the high silica content in the final Zn concentrate were established. Quartz is present mainly as liberated particles (> 60?80 %) in the fine fractions of the products; therefore the selectivity of the flotation process is not effective. Two approaches were tested to reduce the quartz content of Zn concentrate: froth washing in Zn cleaner flotation and new gangue depressants in the Zn circuit. Experimental results from bench-scale flotation and industrial tests show that it is possibile to reduce the silica content of final Zn concentrate more than 2 times without the need for extensive regrinding. The depression of liberated quartz particles on all operations of Zn circuit using stage depressant addition is the right solution to produce high-grade Zn concentrate that meets the metallurgical requirements.

Aug 1, 2013

By Satya Ganti, Bryan Turner, Bill Davis, Veeraraghavan Sundar

This work presents a three dimensional microstructural analysis of medium carbon steels, based on serial sectioning using optical microscopy. The microstructural phases considered here are ferrite and pearlite. Typically conventional 2D microscopy is used to analyze these phases (ASTM E112-13 in Standard test methods for determining average grain size. ASTM International, West Conshohocken, PA, 2013), with eddy current (Khan et al. in J Mater Process Technol Freitas et al. in Mater Sci Eng A 527(16):4431–4437, 2010) as alternatives. Medium carbon steel samples were heat treated in a furnace and either slowly cooled in the furnace, or cooled at higher rates. This resulted in different pearlitic microstructures in the samples. The analysis was conducted with Robo-Met.3D®, a fully automated metallography system for serial sectioning. Based on optical microscopy, volume cubes of hundreds of microns on edge were imaged and reconstructed to conduct grain size and phase volume analysis. The system proved capable of collecting image data with high fidelity, and controlled slice thickness in an automated manner. The resultant dataset was useful in visualization and analysis of pearlite and ferrite phases in steel samples.

Mar 1, 2018

By P. A. Mahanwar

Flyash were melt mixed with nylon 6 at a 30wt% concentration. TYZOR® TPT, a coupling agent, was used to facilitate the link between filler and matrix. The morphological characterization, using SEM, revealed sufficient matrix residue on the filler surfaces thus confirming the strong interfacial bonding between the filler and the matrix on treating. Tensile, impact and the flexural properties of the composites were also improved with the incorporation of coupling agent. As flyash particles tend to impart a grayish color to the plastic, TiO2 pigment was employed to make the formulations aesthetic. The pigment was added to the filled system in 0.1, 0.5, 1.0, 1.5, 2.0 wt/wt ratios. Scattering of incident light and spectral reflectance was higher for smaller particle size flyash. Moreover an increase in the scattering with increase in pigment concentration indicates better dispersion of the pigment, which again is due to the presence of coupling agent.

Jan 1, 2006

By Michael Peterson, Robert Davinroy, Robert Rapp, Gregory Hempen, David Herzog, Thomas Keevin

Fish sampling in a deep-water, high velocity, environment is extremely difficult. Conventional techniques such as electro-fishing and netting have been limited to depths generally less than 7 meters (m) and velocities below 1 meter per second (mps). The goal of our study was to sample a bendway weir field on the Mississippi River to assess the effects of the weir field on the fishery. In a bendway weir field, depths can exceed 20 m, and velocities can exceed 3 mps, making conventional sampling techniques inefficient.

Jan 1, 2002

By Lance Rasband, Richard Hanke, John Starcevich

"The world’s largest tunnel boring machine (TBM), at the time of her launch in 2012, the TBM locally referred to as “Bertha,” is incapacitated due to mechanical failure. Bertha’s stoppage places her 25m below the surface between the aged Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to access all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Due to the limited area above the tunnel alignment and physical constraints created by existing infrastructure, the dimensions of the otherwise symmetrical shaft are heavily impacted, thereby requiring special attention to design and layout. Consequently, the shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude. INTRODUCTION Mining on Seattle’s SR99 tunnel began in July of 2013. Initial mining progressed slowly through a 4.5 m thick fiber-reinforced concrete headwall before immediately entering the first of three planned safe havens. Once through the headwall and safe haven the machine would move through roughly 122 lineal meters of jet grout improved soil at a rate of slightly over 1.6 m per day. It was anticipated that once mining has passed through the improved area, “Bertha” – now the world’s 2nd largest tunnel boring machine (TBM), would be moving at a rate of almost 11 m per day. By the end of October 2013, Bertha had mined roughly 131 m, averaging 1.4 m per day, and had begun mining within native soils. By the start of December 2013, tunneling had reached the 244 m mark and Bertha was now averaging 3.6 m per day, achieving as much as 12.8 m of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt. Initial reports stated an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure within the ground around the TBM, to allow the contractor’s personnel to inspect the cutter head from within and also to investigate for the presence of obstructions at the face of the cutter head. During inspection, the contractor’s crews found fragments of steel pipe entangled in the cutter head. The steel was apparently from an abandoned 254 mm diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, she attempted to move forward but was only able to generate a slow crawl."

Jan 1, 2016

By Mark Spaniel

Computer 3D modeling to evaluate the potential underground blasting fragmentation performance based on rock within calculated damage radii along drillholes, as well as the burden distance from explosives along each drillhole. The results estimated from the 3D computer models closely predicted results found in the real world testing.

Feb 1, 2020