Search Documents

By Y. Yang, S. Peelman, J. Sietsma, Z. H. I. Sun

The rare earth elements (REEs) present in the Kiruna iron ore mine tailings are being considered as a new REE resource for the EU. These tailings, after beneficiation, contain approximately 5000 ppm of rare earths, concentrated in apatite and monazite minerals. To economically extract the REEs from these tailings the phosphorous contained within the apatite must also be extracted and the waste production of the process should be minimal. To achieve the extraction of REEs and phosphorous HCl and HNO3 were investigated as possible leaching agents. Based on the results a leaching process using HNO3 is proposed. This process produces H3PO4 from the apatite while simultaneously dissolving the REEs. The resulting leach liquor is then cooled to remove the unwanted Ca as Ca(NO3)2. Analysis of the leach liquor reveals extraction ratios of between 75% and 100% for the heavy REE (e.g. Y, Eu, Dy, …) and below 40% from the light REEs (i.e. Ce, La). Full phosphorous extraction was also achieved.

Jan 1, 2016

By V Mutton, L Potts, D Joyce

This paper describes the method of extracting sill pillars within the underground operation from under unconsolidated mullock fill at the Cracow Gold Mine. This pillar recovery method was initially successfully used to recover sill pillars at Crusader Mine, Western Australia in 2001. Globally significant resources have been sterilised due to the placement of loose rock fill above crown pillars and within adjacent stopes. The method described here offers significant opportunities to increase recovery of sill pillar recoveries.The royal orebody sill pillars at Cracow Gold Mine form a significant resource. Extraction of these pillars needed to be undertaken with minimal ore dilution and maximum ore recovery. The application that was selected to consolidate the loose mullock fill above each pillar used an injection grouting process (Minova FB200).Cracow Gold Mine mining method is bottom up bench mining. The pillars were left within the orebody to allow for stoping to commence whilst the decline was being developed. Due to the remainder of the orebody being extracted the only access to consolidate the backfill was from the sill pillar extraction level. Numerous problems were encountered and overcome from product selection and trial, system of injection to extraction.This pillar recovery process achieved a 95 per cent recovery of the sill pillar compared with an estimated 60 per cent typical for other mining options.CITATION:Potts, L, Mutton, V and Joyce, D, 2012. Pillar recovery at Cracow gold mine using grouted consolidated mullock, in Proceedings Narrow Vein Mining 2012 , pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By A Karrech, A Hasan

This paper presents the numerical simulation of mine backfilling in underground stopes using three-dimensional discrete element modelling (DEM). The simulation predicts the forces exerted at the stope base and barricade with respect to time under free drained conditions. The results of the numerical simulation are validated using basic analytical solutions and advanced experimental tests involving a geotechnical centrifuge system. Overall, a good agreement between the present numerical simulations and the existing experimental and analytical results was found. The present model suggests that DEM is a promising computational tool to predict barricade pressure in underground mine stopes.CITATION:Hasan, A and Karrech, A, 2014. Simulating mine backfill in a fully drained condition using discrete element modelling, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 117–124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Thomas T. Read

THE official title of our topic for today is "Resources of Metals and Other Strategic Minerals," but in accepting the invitation to open this discussion I claimed the privilege of being allowed to talk about problems other than resources for the two reasons that a great deal has already been said about resources and because we can never discuss them with the degree of certainty that an engineer likes. Resources are uncertain for many, reasons. One is that we do not know what is in the earth. It is four thousand miles to its center and although oil wells 1 ½ miles deep are becoming common and engineers are now talking of drilling holes 2 miles deep, even when they do they will have advanced only one two-thousandth part of the total distance. Only a relatively few mines are over a mile deep as yet. We know certainly that it is comparatively expensive to work at such great depth, but it would be a very foolish man who would assert it will be' impossible, one or two hundred years from now, for engineers to obtain from great depths mineral supplies that are now being obtained at or near the surface. As long as- I can remember I have been hearing that our petroleum resources were in imminent danger of speedy exhaustion, and yet the yearly output is now of the same order of magnitude as the total resources were once estimated, with ' the cry of over-production the loudest it has ever been. Tapping progressively deeper and deeper sources of supply, has produced this result. Even in the thin layer that we are now working much-exploration still remains to be done. .

Jan 1, 1929

By M Steinberg, M Amarant

Upstream Classifier are well-known in the iron ore industry for at least 15 years. At present, more than 60 units are in operation in Western Australia. The advantage of this technology is their capability to produce three products with one equipment – iron ore concentrate, iron ore middlings for further processing and slimes (tailings). The principal of this beneficiation process – upstream classification and upstream separation – will always remain. However, the optimisation of the classification and separation efficiency of the equipment itself is a continuous process driven by enhanced automation and instrumentation, design changes and the use of upstream and downstream information and requirements. Besides efficiency, the safety, maintenance and replacement conditions are very important subjects for the operation of an iron ore mine. The aim of this paper is to present a new allflux® upstream classifier design, which has been developed together with several iron ore producer from Western Australia. The new design benefits from its sustainability approach by dividing the entire equipment into small reusable parts. As a result, maintenance is minor, replacement much faster, lifetime much longer and costs much lower. Furthermore, it demonstrates new features to prevent hazardous working conditions such as confined space as well as new fixing devices to speed up the replacement of certain items and parts.

Sep 18, 2023

By G. F. Jenkins

The word asbestos is a broad term that has been accepted and applied to a number of fibrous mineral silicates found in nature. They are incombustible and can be separated by mechanical means into fibers of various lengths and thicknesses, but differ in chemical composition and other properties. It is generally recognized that there are six varieties of asbestos; the finely fibrous form of serpentine known as chrysotile, and five minerals of the amphibole group, i.e., amosite (not fully recognized as a mineral species name but accepted in asbestos terminology), anthophyllite, crocidolite, tremolite and actinolite. (Figs 1-4.) Physical and Other Properties The structures of asbestos fibers have been studied intensely in recent years. X-ray diffraction patterns 1 to 15 have been used as a means of identification and classification. The amphibole group structures have been fairly well established while the serpentine group has been the subject of many investigations during the past six years. Low-angle X-ray scattering techniques5 have shown that the chrysotile fibrils are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 180Å* units to 300Å units, while the amphibole fibers are many times larger in cross section. The electron micrographs of chrysotile asbestos (Figs 1-4) have also indicated that the fibrils might be in the form of a hollow tube. This point has been the subject of considerable controversy by a number of investigators.7 to 16 Density measurements17 made on a sample of high quality Arizona fiber did not indicate that the fiber had a hollow tube structure; however, the so-called "sheet structure" of the fibril could be distorted in such a way that it gives the appearance of a hollow tube in the electron microscope. It is of interest to quote one investigator, F. L. Pundsack,17 in this connection: Although the empirical composition of chrysotile is 3MgO.2SiO2.2H20, the true unit cell[#] composition is best represented as Mg12(OH)16Si8O20. This cell has dimensions of a= 5.3Å, b = 9.2 Å, and c = 14.6 Å where the "a" direction is the fiber axis. The calculated density of this unit is 2.56 g/cc, a value in close agreement with experimentally determined density values for chrysotile. The exact manner in which the unit cells of asbestos are stacked together to build up a single fiber of chrysotile is not known, but from various

Jan 1, 1960

By Peter Zhang, Todd Minoski, Mark Van Dyke, Daniel W. H. Su

"This paper presents the results of a 2017 study conducted by the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD), to evaluate the effects of longwall-induced subsurface deformations within a longwall abutment pillar under deep cover. The 2017 study was conducted in a southwestern Pennsylvania coal mine, which extracts 1,500-foot-wide longwall panels under 1,185 feet of cover. One 650-foot-deep, in-place inclinometer monitoring well was drilled and installed over a 150-foot by 275-foot center abutment pillar. In addition to the monitoring well, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-foot-wide longwall panel on the south side of the abutment pillar was being mined.Prior to the first longwall excavation, a number of simulations using FLAC3D™ (Itasca, 2017) were conducted to estimate surface subsidence, increases in underground coal pillar pressure, and subsurface horizontal displacements in the monitoring well. Comparisons of the pre-mining FLAC3D simulation results and the surface, subsurface, and underground instrumentation results show that the measured in-place inclinometer casing deformations are in reasonable agreement with those predicted by the 3D finite difference models. The measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models. Results from this 2017 research clearly indicate that, under deep cover, the measured horizontal displacements within the abutment pillar are approximately one order of magnitude smaller than those measured in a 2014 study under medium cover.INTRODUCTIONDue to a recent shale gas boom, approximately 1,400 unconventional shale gas wells have been drilled through active and future coal reserves in Pennsylvania, West Virginia, and Ohio over the past 15 years. These shale gas wells have penetrated many coal seams, such as the Sewickley, Pittsburgh, Upper Freeport, and Kittanning seams. These unconventional gas wells, whether tapped into the Marcellus or Utica formations, contain very high gas pressure. Strata deformations associated with longwall and other high extraction techniques could induce high stresses and deformations in the shale gas well casings. This could seriously compromise the mechanical integrity of the production, intermediate, and coal protection casings (Figure 1). Damaged well casings could potentially introduce high-pressure, explosive gas into underground mine workings, particularly during an extended well shut-in period, which could seriously jeopardize underground miners’ safety and health."

Jan 1, 2018

By H. H. Heady

This Bureau of Mines report provides specific information regarding the analysis of ores, concentrates, and bullion. It describes analytical services provided by some Federal agencies, and discusses analytical techniques applicable to the precious metals. The appendixes list Bureau of Mines State Liaison Offices and commercial assay laboratories.

Jan 1, 1976

By RICKARD HANSEN

With vehicles frequently found in underground mines and tyres being a major fuel item, the risk of tyre fires will be severe underground. This study presents an in-depth analysis of tyre fires on mining vehicles to increase the knowledge of the risk, applying data from full-scale fire experiments and CFD simulations. It was found that the wheelhouse of the loader caused an increase in the flame tilt angle of approximately 10%, decreasing the flame impingement and heat flux downstream. The flame temperature of the drilling rig tyre was found to be approximately 7% higher than the loader tyre, increasing the risk of igniting adjacent fuel items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for the drilling rig case for higher flow velocities, indicating the influence of a varying wheelhouse/mudguard construction and tyre geometry on the flame tilt angle. The construction of the loader resulted in a flow behaviour, where the short distance to the front mudguard/tyre and the separation of flow directly downstream of the protruding construction led to fire gases being steered past the front mudguard/tyre. In the drilling rig case, the longer distance to the front mudguard/tyre led to fire gases being directed towards the body of the vehicle after passing the area with flow separation. An increased knowledge of the tyre fire risk on mining vehicles and mitigating measures would improve the fire safety in underground mines.

Feb 10, 2022

By D G. Boxall

As an alternative to heavy water cooling, reactors cooled by organic liquids are being actively developed in Canada under the sponsorship of Atomic Energy of Canada Limited. One of the areas in which development has been required is that of core materials. The factors affecting the selection of fuel canning and coolant tube materials are discussed. It is shown that S.A.P. is a potentially attractive material for these applications. The fabrication of fuel sheathing is discussed. Difficulties met due to large inclusions and blistering due to high hydrogen contents have been overcome by magnetic separation and vacuum sintering of the powders. High-quality tubes can now be produced by extrusion to finished size. A study has been made of the mechanical properties of fuel-sheathing tubes and bar stock. The stress rupture properties of the tubes subjected to uniaxial and biaxial stress have been determined. The biaxial stress tests were performed by internal pressurization. For times in excess of about 200 hours, the curve of stress against time to rupture is extremely flat. The secondary creep rates of

Jan 1, 1965

By Patrick Andrieux

Numerous rock blasting design methodologies have been developed over the years, relating either to the primary objectives of blasting, such as the size distribution of the blasted material, or to its undesirable side effects, such as damage to the remaining rock mass. All existing methodologies, while of use, do have serious shortcomings. The question remains whether further improvements can be achieved in the field of practical rock blasting engineering. One approach that seems to hold promise is the relatively new matrix-based rock engineering systems (RES) methodology. It has been conceptually demonstrated that RES could be efficiently adapted to blasting. A brief overview of rock blasting design techniques and their main shortcomings is followed by the basic concepts governing rock engineering systems and a discussion on their pertinence to blasting. The paper concludes with a review of current efforts to develop a useful practical blast design tool using RES. SOMMAIRE Le potentiel d?application des systèmes d?ingénierie du roc aux tirs à l?explosif. De nombreuses méthodologies de conception d?abattage du roc à l?explosif ont été développées au cours des années, qui ont adressé soit les principaux objectifs des tirs, comme par exemple la granulométrie du matériel dynamité, soit ses effets secondaires indésirables, tels les dommages au massif rocheux. Toutes les méthodes existantes fonctionnent dans une certaine mesure et sont utiles - elles sont cependant pour ainsi dire toutes affectées par des limitations ou défauts plus ou moins sévères. La question demeure quant à savoir si des améliorations supplémentaires peuvent être apportées dans le domaine de la conception pratique des opérations d?abattage du roc à l?explosif. Une approche alternative qui semble prometteuse est celle relativement récente des systèmes matriciels d?ingénierie du roc (?Rock Engineering Systems?, ou RES). Il a été démontré de manière conceptuelle que les RES ont le potentiel d?être adaptés aux opérations de sautage. Une brêve revue des principales techniques de conception des tirs à l?explosif est suivie d?un énoncé des principes de base gouvernant les RES, ainsi que d?une discussion sur leur pertinence aux opérations de tir. Cet article conclut avec la revue d?un projet de recherche axé vers le développement d?une méthodologie de conception des tirs à l?explosif basée sur les RES.

May 1, 2002

By Walter W. Bradley

FOR a number of years up to the economic setback of the 1929-1931 period, the greatest proportional advances in the mineral industries in California were made among the substances in the nonmetallic groupings, particularly among the so-called industrial minerals and the salines. During the past year or two, although these have not regained the stride that marked their progress in the preceding decade, we can still record, -some new developments. California produces annually between 55 and' 60 different minerals on a commercial scale. Of these, some 40 to 45 comprise the "structural," "industrial," and "salines" materials as grouped in the reports of the State's Division of Mines. Barite-The barite deposits of California were described in Report

Jan 1, 1935

By R. A. Wyman

What unusual features are there about finding, winning, and using the industrial minerals of Canada which may be of interest and yet not widely known. Have you, for example, ever wondered where the raw material for those distinctive greenish grey statuettes, so readily recognizable as Eskimo carvings, comes from? Although stone suitable for carving is obtained at several northern locations, in recent years the Federal government, the Quebec government, and one or two private companies have shipped supplies of various rock types from other sources to central distribution points in the Canadian north for the express purpose of providing Eskimo artists with raw materials for carving. Canada is well endowed with industrial minerals, the extent and variety of which may be observed by a perusal of Table 1. In this table, materials currently produced are shown in the left-hand column; materials which are bordering upon economic viability are listed in the middle column; and materials which have been found in Canada in possible exploitable quantity, but for which [ ]

Jan 1, 1970

By R. S. Farinato

Thionocarbamate flotation reagents have enjoyed a niche position in the recovery of copper sulfides and activated sphalerites since their introduction in the mid 1950's (Harris, 1954). Thionocarbamates containing an allyl group (-CH2- CH=CH2), introduced recently Lewellyn, 1985; Nagaraj, 1988; Avotins, 1991), are used commercially as collectors for copper sulfides and activated sphalerite. Laboratory flotation tests and plant usage have demonstrated that allyl-containing thionocarbamate collectors exhibit certain unique properties that distinguish them from the corresponding dialkyl thionocarbamates. Spectroscopic (FTIR, XPS) and wettability studies of N-allyl iso-butyl thionocarbamate (AIBTC) and its saturated analog N-propyl iso-butyl thionocarbamate (NPIBTC) adsorbed on copper at pH 9 were performed in order to investigate whether there were any fundamental reasons for these differences. Flotation tests were carried out on chalcocite, copper ore and an activated sphalerite.

Jan 1, 1993

By M. Dale Slade, Gordon S. Bird, Robert S. Kelly

Gallium scrap is obtained from many different sources, therefore each lot received has to be evaluated and then processed accordingly. Some of the problem areas are separating small amounts of gallium from large concentrations of iron, eliminating trace amounts of gold, silver, copper, germanium, tin, and zinc from gallium, and having the flexibility to process each lot of scrap individually Following gallium from the raw scrap material to the final seven nines pure product requires stringent quality control and excellent analytical capabilities.

Jan 1, 1983

By E. J. Murphy, John C. Holtz

"INTRODUCTION Toxic gases in the products from the detonation of explosives are one of the hazards in blasting underground. Investigations by the Bureau of Mines 4/5/ have shown that the oxygen balance of the explosive is an important factor in the control of toxic gases. This balance is considered in determining the composition of modern metal-mining explosives for blasting underground, and application of the concept has reduced the volume of toxic gases generated.The chemical nature of the material being blasted also influences the composition of the toxic gases produced. Under some conditions of blasting in massive pryrite, unsafe concentrations of sulfur dioxide and hydrogen sulfide have been found.Experiments with the O-J apparatus 8/ have shown that there is an increase in the volume of carbon monoxide in the gaseous products when permissible explosives are detonated in contact with coal dust. Thus, reactive materials of a reducing nature adjacent to explosives loaded in drill holes may decrease the effective oxygen balance of the explosive and cause the volume of toxic gases to increase.Several blasting accessories of reducing nature have been introduced recently for use in coal or metal mines or tunnels. In practice these are loaded adjacent to the explosive where conditions favor reaction with the products of detonation. The effects of this loading on the gaseous products obtained from the shot are indicated in this report. Broad consideration was not given the efficiency, usefulness, or over-all safety of these devices, but the practical significance of the hazard resulting from increased volume of carbon monoxide is discussed."

May 1, 1942

By Scott R. Giese, Lucas Dix

"Recently, there is a growing trend in the aluminum foundry industry to develop· improved melting and casting processes to produce lightweight, high-strength, and thin-wall castings for the aerospace and transportation industry. One casting method that has demonstrated industrial potential for producing clean, thinwall castings is vacuum-assisted, counter gravity casting. This process has the benefit of expeditiously and quiescently filling the casting cavity with a dramatic reduction of furnace related and reoxidation inclusions. Additionally, lower casting temperatures can be utilized because the application of vacuum during filling overcomes the resistive internal cavity pressure resulting in a finer, as-cast microstructure. The paper explores and discusses the processing and design conditions in improving the mechanical properties of A206 casting alloy using the vacuum assisted, counter gravity casting process.IntroductionThe process of metal casting has been, over the centuries, the chief production technique for components used in everyday life. However, the casting process has certain inherent problems that can adversely effect the properties of a finished product. These problems are directly attributable to the gravity pouring technique used to transfer molten metal to the mold and to fill the mold cavity.A recent study for the American Metalcasting Consortium demonstrated reoxidation products created during the casting process are five times more likely to cause product rejects than entrapped molding aggregates, melt slag, or furnace lining materials1. Formation of nonmetallic and intennetallic compounds are more prevalent in aluminum and titanium alloys because of their reactiveness to furnace lining materials and their high affinity for oxygen. The incorporation of undesirable compounds can be attributed to four areas of the casting operation. The sources are charge materials, melting technique, pouring methodology, and casting cavity filling. Aluminum foundry men have addressed the first three areas by selecting high quality melt stock, non-stirring melting equipment, and the use of porous ceramic filters. Unfortunately, little consideration is given to the last, but yet tl.1e most important part of the casting operation, the actual fill mg of the casting cavity.The generation of inclusion defects during the casting process can be described by two methods. As the liquid metal flows in the gating network and casting cavity, abrupt changes in flow d1rect10n cause the metal to become agitated. This mechanism liquid metal splashing, is generated by instability of the advancing liquid metal interface from turbulence effects as schematically illustrated in figure 1a2 . The surface oxide film bursts under high velocity conditions, folds over, and becomes dispersed and incorporated in the bulk liquid. Additionally, fragmented liquid droplets ejected from the disturbed interface oxidize and become dispersed in the metal stream."

Jan 1, 2000

By T Hodgkin

The WA Goldfields is a highly productive gold and nickel mining area, but is arid with highly saline groundwater. Groundwater is widely used to supply process water to mines in the region but high groundwater salinity, commonly exceeding 50 000 mg/L TDS, tends to increase processing costs, limit end uses for the water, cause problems with disposal and potentially increase impacts on a sensitive arid environment. The area has low rainfall (200 - 270 mm/year) but run-off, particularly during cyclonic events, is high. Our experience suggests that stream flow from catchments in the area can produce a divertible yield of 8 - 17 ML/km2/year. An evaluation of stream flow harvesting using AnglogoldÆs Jubilee Pit predicted that 1000 ML/year of good quality water could reliably be supplied to the Sunrise Dam Gold Mine. Because of high rainfall variability, it is likely that an alternate source of water supply will be necessary when operating a surface-water harvesting scheme in the WA Goldfields. However, a combination surface/groundwater supply could have substantial cost, operational and environmental benefits compared to traditional supply systems that utilise groundwater only.

Jan 1, 2003

By Tim O’Neil

“America’s mining industry brings good jobs to communities across America and provides the energy, minerals and equipment that are vital to our economic security and our way of life.” That was the surprise videotaped greeting from President George Bush at the official opening ceremony of MINExpo 2004in the Las Vegas, NV Convention Center. Jack Gerard reinforced the upbeat mood at MIN-Expo. He praised Nevada Gov. Kenny Guinn for his support of the mining industry, the state’s largest manufacturing sector. Gerard is the president and chief executive officer of the National Mining Association, the sponsor of MINExpo 2004.

Jan 1, 2004

By R. Riding

Degussa Corporation's peroxide-assisted leaching (PAL) process was evaluated in the batch concentrate leach circuit at Hecla Mining Company's Republic Unit. The product leached in this batch circuit is a high grade gold-silver sulfide (predominately pyrite) flotation concentrate. The primary objectives of the test program were to determine the effects of dilute hydrogen peroxide addition on leaching kinetics, sodium cyanide consumption and precious metals recovery. The results of the testing demonstrated that using dilute hydrogen peroxide produced the following benefits: - 1. Batch leach time requirements decreased by 80%. - 2. Sodium cyanide consumption in concentrate leach reduced by 55%, which translated to an overall plant reduction of 20%. - 3. In the concentrate leach process, gold recovery was increased by 1 to 2%. Because of the excellent metallurgical results achieved with the use of dilute hydrogen peroxide, as well as an economic incentive, PAL has become standard practice in the concentrate leach circuit operation. A complete description of the Republic PAL plant evaluation and performance is provided in this paper. In addition, process chemistry considerations in regard to the role of hydrogen peroxide are discussed.

Jan 1, 1992