Search Documents

By Verne E. Hooker

In situ stresses, based on isotropic and anisotropic relations, were evaluated using computer techniques from overcoring data obtained in dimension stone quarries along the Appalachian Piedmont, the Ozark Uplift, and the Ouachita Tectonic Belt. Stresses in the horizontal plane near the surface are compressive and range from 100 to 4,500 psi. The direction of maximum compressive stress seems to be alined with the general tectonic structure for most of the determinations. The ratio of the maximum to minimum elastic parameters in the horizontal plane ranges from 1.05 to 2.46 for these competent rocks. Isotropic versus anisotropic stress determinations show differences only as great as 25 percent in stress magnitude and 25° in orientation.

Jan 1, 1969

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.

By Warwick D. Bullen

Gold mining in the Yellowknife area of the Northwest Territories started long before the concept of sustainability entered the academic literature and by the time the term enjoyed widespread public acceptance, the Yellowknife gold mining industry was in its sunset years. Nevertheless, the city of Yellowknife will long outlive the gold mines that it was founded on, demonstrating that not only can mining build sustainable communities, but that sustainable mining as a concept is an entirely valid precept. To this effect, the authors examine the complex economic and social aspects of the gold mining industry in the Yellowknife area over the last 70 years.

May 1, 2004

By Gwendolyn D. Hood

The Bureau of Mines investigated techniques for dewatering slurries from talc-processing operations to improve water reclamation and pro-duce dewatered solids suitable for disposal. Various flocculating reagents were evaluated, and a nonionic polyacrylamide was found to be most effective in a specialized flocculation dewatering technique. The flocculation dewatering method was applied in laboratory batch tests and in continuous tests using a static screen, a belt-roller device, and a clarifier-thickener laboratory unit. In continuous tests using the unit, wastes of 3.5 pct solids were dewatered to 56.9 pct solids using 0.03 Ib of flocculant per ton of dry solids treated.

Jan 1, 1983

By D Timms

The Kempfield deposit is located in the Hill End Trough, one of several intracratonic basins developed during Silurian–Devonian time, in the eastern province of the Lachlan Orogen, Eastern Australia.The deposit contains an oxide resource of 5.8 Mt @ 58 g/t Ag and a sulfide resource of 14.4 Mt @ 45 g/t Ag, 1.7 per cent Zn and 0.6 per cent Pb, classified and reported in compliance with the JORC Code. The deposit has been previously explored by a number of companies, including INCO, Shell, Jones Mining, Golden Cross Resources and recently Argent Minerals Ltd (Argent). Argent is currently completing a definitive feasibility study with a view to mining the deposit.The deposit is hosted at the boundary between the Molong High to the west, comprising Ordovician sediments and volcanic rocks and the Hill End Trough to the east, interpreted as a back-arc basin containing Silurian sediments and siliceous-feldspathic volcanic rocks. The boundary between these two strato tectonic units is an imbricate thrust fault zone known as the Copperhannia Thrust.The Kempfield deposit is hosted in felsic volcanic rocks known as the Kangaloolah Volcanics. These have been in-faulted and folded into the Middle Ordovician meta-sediments of the Coombing Formation of metasediments along the Copperhannia Thrust. The Kangaloolah Volcanics belong to the Late Silurian Mumbil Group, comprising submarine carbonate-shale facies interspersed with extensive felsic volcanic piles, which grade conformably upwards into turbiditic sandstone and siltstone sequences (interpreted to represent a deeper depositional environment). These turbiditic rocks are known as the Campbells Formation, comprising siltstone, sandstone and andesitic tuff. The rocks at Kempfield are metamorphosed to lower greenschist facies, reflected through the different type of schists.Silver, gold, lead, zinc mineralisation is hosted in barite-rich horizons, near the boundary to quartz-phyric tuffaceous rocks in submarine, immature, reworked felsic ash tuffs. Barite appears to be hosted in greatest concentrations by the coarser grained volcanoclastic sandstones and grits, whilst intercalated siltstones are volumetrically minor and tend to return low barite and silver. Mineralisation is hosted in stratiform and probably stratabound barite-rich horizons. A northeast-trending, steeply dipping, metamorphic cleavage (S1) occurs throughout the project area.

Aug 22, 2011

By S Tjerry, S Szylkarski, B Willis-Jones, I Dubinski

Achieving relinquishment of mining sites is becoming increasingly difficult, with a study by Byrne (2013) estimating that out of a set of 73 mining and metals sites around the world, less than ten per cent had achieved relinquishment over the last 50 years. The median forecast duration of time allocated for water management in the closure plans studied was approximately ten years, while the reality at the actual sites was a median duration of 22 years to date and growing.One of many challenges in mine closure planning is managing geomorphic stability of stream diversions. The challenge is to be able to demonstrate to regulators and the community that a proposed rehabilitation solution will be stable over the long term.During the mining operations, local watercourses and surface drainage can be diverted and managed using engineered channels and drainage structures. However, during the post-operations stage, the engineered channel and drainage may require modification to a more natural condition that will facilitate long-term environmental sustainability. Achieving geomorphic stability of a diverted watercourse is difficult, with the majority of stream diversions in Australia failing to meet expected design performance (White et al, 2013). Geomorphic stability is a complex process that is controlled by a combination of factors, including hydraulic flow conditions, geotechnical conditions and vegetation.This paper proposes that a fully dynamic and deterministic geomorphological model can be used to supplement the traditional empirical approaches to assess long-term geomorphic stability. The paper provides an overview of the geomorphological models and how they have been applied in engineering studies for forecasting future evolution of stream systems. The paper discusses the potential application of these models in the mining industry for forecasting and optimising surface water structures for the operations and post-operations stages of the mining cycle.CITATION:Szylkarski, S, Willis-Jones, B, Tjerry, S and Dubinski, I, 2016. Improving the reliability of stream diversion designs in mine closure plans using a morphological tool, in Proceedings Life-of-Mine 2016 Conference, pp 212–215 (The Australasian Institute of Mining and Metallurgy: Melbourne)

Jun 28, 2016

By W. L. Single

"LET ME FIRST OF ALL thank you for sending this invitation to me to participate in this Annual Meeting of The Mining Society of Nova Scotia. As an engineer, although I don't get an opportunity to practice very much engineering these days, I am, of course, always pleased to be able to meet with my fellow engineers to exchange views, but I must admit that today I feel a little bit out of place in the midst of all the experts that are here today. Let me make one thing clear - I'm a generalist! Your program states that I am to make a keynote address. I have always thought that a keynote speech is one that says something that has not been said before - announces some new program or policy, or says something startling. I am sure you will understand when I tell you that keynote addresses are made by politicians and that civil servants speaking publicly are usually expected to give an account of what is, or what is likely, to happen as a result of policies that have been announced in keynote speeches by politicians. I am reminded of a statement by a distinguished parliamentarian who said, ""However exalted a civil servant may be, he is not above the elected officials."" So today I will confine myself to giving you an overview with particular emphasis on the development side of oil and gas. The theme of ""Oil and Gas"" is a topical one these days. I suppose it's because of all the copy that is being generated by the media on the U.S. energy crisis, the Mid-East situation, the fact that most of the world's proven oil reserves are in Arab hands and, of course, the accelerated exploration activity that is taking place in the North Sea, in the Arctic, and off the coast of Newfoundland and Nova Scotia."

Jan 1, 1973

By Wang Zhi

High-Mg-content concentrates are usually treated in Jinchuan flash smelting Furnace. Because the viscosities of high-Mg-content slag is very high, the operation of flash smelting becomes very difficult. To solve this problem, the viscosities of the semi-synthesized FeO-MgO-Si02 slag of different compositions were measured. The results showed that when in the slag the weight percentage of MgO [m(Mgo)] is 6-10%, the ratio of the weight percentage of iron to that of Si02, m(Fe)/m(SiO2) is 1.1-1.4 and the temperatures are within 1473?1773K, the slag viscosities increased with the increase of m(Mgo) and m(Fe)/m(sio,). When m(Mgo)<6%, the smelting temperature should be controlled at I 300°C in order to to keep the smooth operation. When m(Mgo» 10%, the temperature should be kept above 1633K. When the content of MgO is higher, a lower viscosity slag ean be produced by decreasing the ratio of m(Fe)/m(sio,). The appropriate ratio of m(Fe)/m(sio,) for Jinchuan flash smelting furnace is about 1.2.

Jan 1, 2003

By D. Norval

Keywords: Pyrometallurgy, slag, metal, entrained, granulation, ferromanganese Water granulation of certain slags with high metal entrainment has customarily not been practised, not only due to the belief that such processes are too dangerous and unproven in the pyrometallurgical industry, but also that it might not be economically viable or environmentally acceptable. General slag granulation, on the other hand, is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. Thus, purpose-designed granulation and solidification processes are discussed, taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte, or alloy responds in similar fashion to a granulation practice. This paper addresses three issues, namely: ? Water-granulation of BOF steel slag, without processing it to render it environmentally safe, physically and chemically acceptable for use by the construction industry, and the process economical ? Processing air-cooled BOF steel slag to change its physical and chemical properties to be acceptable for various uses and extracting metallic and bound iron ? Processing air-cooled or molten manganese slag to lower its manganese content to a level that is acceptable from an environmental and health point of view, and extracting FeMn-alloy of acceptable composition. The latter process culminated in a patented process to extract FeMn from air-cooled and molten manganese slag, and, at the same time, produce a hydraulic (cementitious) slag, thus transforming a possible hazardous by-product into virtually 100% saleable products.

Jan 1, 2011

By A. J. Hofmann, G. P. R. van der Merwe, J. E. W. Holm

"A new approach is proposed to perform relativistic comparisons between alternative operational risk management solutions by taking into account the impact of each operational activity on overall system performance. A specific case study, to which this new approach is applied, involves the deployment of safety systems in underground mining operations. Conflicting objectives to be satisfied are the minimization of risk to human lives and the minimization of production losses. As the focus in this case is primarily on the mitigation of risk, the approach that was applied is referred to as activity-based risk (ABR) analysis. Existing development process and risk management methods used in the South African mining environment were analysed by means of observations, a case study, technical documentation, and literature review. It was evident from this analysis that a discontinuity existed between the acquisition and operational phases in terms of the management of safety risk in the acquisition of electronic safety equipment when viewed from a full lifecycle perspective. This discontinuity could be addressed by defining a risk perspective in the system development phase by employing ABR in the preliminary design phase of a system’s engineering life-cycle. The focus of the ABR system development process is to find the functional definition and configuration of safety equipment that addresses both safety and productivity when taking into account human performance variability. In doing so, a balance between productivity and safety is found in a relativistic sense. IntroductionIn any system life-cycle, two major phases exist, namely system acquisition and operation (including maintenance). A distinction is made between acquisition and procurement, where acquisition includes system development and integration as specific engineering activities. In the development phase of a new system, conceptual design, preliminary design, and detail design phases follow in this order to define a complete system, after which the system is put into production and implemented in an operational environment—these activities chronologically define system acquisition in the context of this paper. It is not uncommon that differences exist between the risk management perspective during acquisition of a system and risk management perspective during operation, where nontechnical aspects are often ignored during acquisition, but are then encountered and found to be problematic during operation (Leveson, 2012). These differences also exist in the mining industry."

Jan 1, 2017

By John Griffen

Methods of coal preparation in England, including usage of American units such as the Chance sand flotation process and Denver flotation cells, are compared with methods used in the United States. Problems of the coal industry in Holland are summarized.

Jan 2, 1951

By B. B. Cox

Since our last review of Iraq,&apos; considerable progress has been made not only in exploiting Iraq&apos;s potential resources but in building pipe lines to carry the oil to the Mediterranean. No new fields were discovered in 1933. The Naft Khaneh field, discovered in early 1927 by the Khaniqin Oil Co. (subsidiary of the Anglo-Persian Oil Co.), continues to supply the local markets through the Rafidain Oil Co. Kirkuk field, discovered by the Turkish Petroleum Co. Oct. 14, 1927, remained shut in pending the completion of the Mediterranean pipe lines, and the Qaiyarah field, discovered by the same company on Oct. 13,1927, was abandoned in 1928. The principal development of interest during the year was the progress made on construction of the Iraq Petroleum Company&apos;s 1152-mile pipe line from Kirkuk to the Mediterranean. The line is double 10-in. and 12-in. pipe for 156 miles west of Kirkuk, where the parallel lines bifurcate, one leg going through British mandated territory to the new port of Haifa and the other through French mandated Syria to Tripoli. Each line may be operated independently of the other. There are three double stations on the Kirkuk-Haditha portion, four single stations on the Tripoli leg, and five on the Haifa in addition to a relief station in the Jordan Valley. Except for the Jordan Valley section and two other short stretches on the Haifa leg where pressures are exceptionally high, the line is single. Sea loading lines will be used exclusively at Tripoli and both sea loading lines and dock loading will be employed at Haifa. All pipe was welded and buried before the end of December, 1933. It is anticipated that enough stations will be completed to make 50 per cent capacity operation possible some time during the latter half of the current year. Some months will then be required in which to fill the line, so that if terminal facilities are ready and no unexpected emergencies arise, partial daily deliveries of Iraq crude may be received at the Mediterranean some time during the final quarter of the current year. Capacity operation of 84,000 bbl. per day is not anticipated much before the middle of 1935. Oil and Gas Production No gas is produced commercially and, except for Naft Rhaneh production, no crude is marketed. Although the Turkish Petroleum Co. and

Jan 1, 1934

By Zhenfeng Zhou, Qingguo Xue, Jingsong Wang, Yingli Liu, Yuanyuan Zhang, Hailong Huo

Coal burnout strongly depends on the residence time and dispersion of coal particles in the raceway region of a blast furnace. The residence time and dispersion of coal particles are directly related to the lance arrangement. In this work, a three dimensional model was developed to simulate the lance-blowpipe-tuyère-raceway region of a blast furnace. Double lance and eccentric configurations were considered. For the double lance, the double-lance and eccentric double-lance were considered. For the eccentric double lance, the effect of intersection angle of the two lances was investigated.

Mar 1, 2017

By M. S. Badollet

Introduction Very little fundamental research has been done on asbestos fibre to cake maximum advantage of its properties and to determine in what commercial products it can best be utilized. For the research chemist who is associated with asbestos development work, a thorough study of mineralogical information on asbestos deposits would furnish reliable information on the rock formations and the mineral impurities closely associated with the asbestos. Furthermore, ?he must have an intimate knowledge of the uses of the fibre in various products so that he can visualize the importance of the fibre and the role it plays in industry. Some of the properties of asbestos fibres such as strength, composition, length, harshness or softness, and mineral associates are of considerable importance to the manufacturer because they are responsible for many production difficulties. Fibre Strength It has been known for some time chat asbestos filaments have considerable tensile strength. These strengths have been referred to merely as &apos;weak&apos; to &apos;very strong&apos;. Not until recently have numerical values been applied to the strengths of asbestos fibres. But today we can take a thin fibre filament and mount it between two holders and apply a gradually increasing load or pull until the fibre breaks. By measuring the cross sectional area of the filament and the amount of load applied, we can calculate the tensile strength of the fibre in terms of pounds per square inch. This type of test is slow and rather difficult, but the fundamental data obtained furnish important basic information that can be applied to mechanical processing equipment and to certain asbestos products.

Jan 1, 1948

By C. L. Siebenthal

C. E. SIEBENTHAL, ? Washington, D. C.-From being one of the most maligned of metals-a veritable bugaboo-cadmium has almost overnight become respectable, though its slender claim to respectability rests almost wholly on the possibility of its substitution for tin. Preliminary to any campaign for such substitution, particularly for enforced substitution, the possible supply of cadmium should he determined as closely as possible; for that reason the statistical inquiry of which this paper embodies the results was undertaken. Production Cadmium is marketed in two forms, as metallic cadmium, in sticks or bars, and as cadmium sulfide, the pigment. The metal has found its greatest field of use in this country as a component of an easily fusible alloy that is used in automatic fire extinguishers. The sulfide is .used to some extent in paints but chiefly to give color and luster to glass and porcelain. The metal was first made in this country by the Grasselli Chemical

Jan 12, 1918

By E. Karampinos, P. Morissette

"INTRODUCTION Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting both appropriate systems and the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation. Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights on the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement over the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is not often available at mine sites. Even when the expertise is available it requires a major time and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support. Rock reinforcement is an integral part of all ground support systems used in underground mines. Long flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This paper focuses on the optimization of the cable bolting strategy in squeezing conditions at the LaRonde Mine by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 1, 2018

By D. W. Frommer

Composite samples of nonmagnetic taconite from the western Mesabi range were evaluated by reductive roasting, fine grinding, and magnetic separation to determine potential sources of concentratable material. Although large tonnages of nonmagnetic taconite are known to occur in the western Mesabi district, these materials are not as yet a commercial source of iron ore. The technique employed permits the evaluation of individual composites and blocks of composites in terms of responsiveness to a process of potential commercial significance. The 159 composites, from open-pit mines located between Grand Rapids and Chisholm, Minn., were evaluated in the following sequence: 1. Minus 8-mesh material was roasted at 500° C. in hydrogen. 2. The roasted are was ground to one or more sizes in the minus 100-to minus 400-mesh range. 3. The roasted ground ore was magnetically separated in a Davis tube. 4. Composites were classified according to degree of grinding required to produce minimal concentrates. (Minimal concentrates are herein defined as those containing less than 10 percent silica, and responsive composites as those yielding minimal concentrates.)

Jan 1, 1962

By Vladimir N. Rudashevsky, Louis J. Cabri, Nikolay S. Rudashevsky, Thomas Oberthür

"EPD (Electric Pulse disaggregation) and HS (hydroseparation) are exceptional technologies for research, concentration, evaluation, and mineral extraction of specific minerals such as precious metals (Au, Ag, PGM), kimberlites (extraction and concentration of indicator minerals), zircons and baddeleyite (recovery of objects for geochronology), and even gemstones (method of evaluation and production of the 100% gemstone concentrate of ideal crystals) etc. EPD is used for recovery of pristine undamaged crystals of diamond, emerald, ruby, sapphire etc, including large crystals. It was tested on various hard ores and was especially successful for recovery of “soft” minerals from “hard” matrix. EPD products are very convenient for HS processing, resulting in representative concentrates of all heavy minerals including the finest particles (5-10 µm). The combined EPD and HS method enables high sensitivity (20 ppb) for evaluation of precious metal ores providing objective information about original grain size, associations, and recovery using a very small amount of sample (1-3 kg). Latest developments of EPD and HS techniques at CNT Mineral Consulting Inc. include the HS-21 hydroseparator (50 kg/hr) and the Spark-21 EPD (5 t/hr), which enables use of both techniques for prospecting and mineral processing of industrial size samples of certain ores.INTRODUCTIONThe main task for mineral processors is to find a reliable technology for testing of mining feasibility and the efficiency of mineral extraction procedures. Among various mineral processing approaches of extraction and concentration there are two alternative cost-effective methods that can be described as the most environmentally benign and complementary: electric-pulse disaggregation and hydroseparation. These techniques were tested on many different ore types and process products with great success providing a precise and comprehensive mineralogical determination of different accessory precious metal and other useful minerals constituent in rocks, ores, and tailings.This article describes several examples of EPD and HS use: native gold from the Kostomuksha deposit (Karelia, Russia), a Ag-Au deposit in South America, zircons from ancient ultramafic igneous rocks of SW Greenland, bauxites of West Australia, PGM from the Driekop dunite pipe and gemstones (ruby, sapphire, emerald and demantoid) from different deposits."

Jan 1, 2008

By J. B. Cheatham

Applications of the mathematical theory of plasticity promises to lead to the solution of many drilling and rock mechanics problems. ,Because of mathematical considerations, the inelastic behavior of rock has frequently been represented by a perfectly plastic model in conjunction with a yield criteria of the Coulomb or Mohr type. The totality of all stress states for which a solid ceases to behave elastically can be represented as a limit surface in stress space. ,Probing of such limit surfaces indicates details of strain hardening which are not provided by the standard triaxial testing procedure. Probing tests of the limit surfaces have been performed on Cardova Cream limestone to provide data for extending plasticity theory to cover situations in which consolidation and strain hardening are present. Test results indicate that this highly porous limestone undergoes a permanent volume decrease when it is subjected to hydrostatic pressures in excess of 3,500 psi. A virgin sample tested under a confining pressure of 1,500 psi has a yield strength of 1,700 psi; however, if the sample is subjected to a consolidation pressure of 5,000 psi, before testing at 1,500 psi, the yield strength is raised to 2,300 psi. Thus, both consolidation and strain hardening are important considerations in describing the mechanical behavior of this limestone. Tests conducted with the axis of the core having different orientations indicate that this rock is also anisotropic. Portions of the initial and subsequent limit surfaces are determined for samples loaded either perpendicular or parallel to the bedding planes. INTRODUCTION Previous experimental work in rock mechanics indicates that no mathematically tractable constitutive theory is inclusive enough to describe the mechanical behavior exhibited by all types of rocks under all conditions of stress and temperature. Indeed, the type of deformation encountered in a single type of rock is known to depend upon the stress and temperature conditions in the rock during deformation.l-5 Certain rocks and minerals, notably those minerals composed of ionic salts, have been shown to exhibit plastic deformation when tested under conditions of high confining pressure.2 Since the mathematical theory of plasticity provides simplifications over the theory of elasticity in certain types of problems, such as those in which limit analysis can be applied, it is of interest to know under what conditions plasticity theory may be applied to rock mechanics problems. The following factors determine the nature of the deformation a particular specimen will undergo: (1) the microscopic structure of the rock, i.e., the structure visible under an optical microscope, including number of phases, porosity, distribution of phases, (2) the mineralogical structure of the solid phases, (3) the conditions of stress and the rate of change of stress and (4) the temperature. Extensive experiments on Yule marble, Carthage marble, Solenhofen limestone and other calcerous rocks indicate that these relatively nonporous rocks deform plastically under certain conditions of loading, and creep under other conditions of loading.l-3 This study is concerned with the behavior of Cordova Cream limestone (Austin chalk) which is also composed almost entirely of calcite and thus has the same mineralogical composition but, because of a rather large porosity, it possesses a different microscopic structure. This investigation was undertaken to learn if Cordova Cream limestone deforms plastically despite the embrittling effect of the pore spaces, and to provide data which can be used to determine whether the mathematical theory of plasticity can describe the mechanical behavior of Cordova Cream limestone. A brief discussion is given of some of the underlying principles of plasticity theory concerning stress space and limit surfaces. Strain hardening is defined and a discussion is given of how the mechanical behavior of a material can depend on the previous history of the loading. This is followed by a description of the experimental procedures

By Raymond Mancha

A test of any fan requires the determination of such data as fan pressure, air volume handled by the fan, and power input to the fen shaft. When testing operating mine fans of the centrifugal type, test methods have been employed, for the sake of convenience, that permit great latitude in detail of procedure resulting in wide variance in results by different investigators. Some controversial aspects of field fan testing are the result of past failure to define clearly the various forms of fan pressure and to a lack of understanding of the accurate procedure for the measurement thereof. Also, the anemometer for air-volume measurement, although convenient, if carelessly used and maintained is subject to a wide error range with variation in method of application and in instrument accuracy. The appearance of the axial-flow type of mine fan offers the possibility of refinements in field testing that were impractical with the centrifugal fan. First of all, the fan inlet and outlet are more sharply defined, giving closer agreement as to just where the fan begins and ends; thus there is less disagreement as to the proper location for measurements of fan pressure. The area of passage into the inlet of an axial-flow mine fan usually constricts, causing high air velocities with accompanying steadiness of flow. Thus the fan inlet offers an ideal location for accurate air-volume measurements with the pitot tube, the proper use of which is well established by code. Thereby the controversial aspects of such measurements are eliminated. Use of the Pitot tube also facilitates a more accurate measure of fan pressure, since the individual pressures measured can be properly weighted, as will be explained later. Determination of power input to the axial-flow mine fan operating in the field is subject to the same inaccuracies as with the centrifugal fan if the axial-flow fan is also belt driven. However, because of the higher rates of rotation usual with axial-flow fans, direct-driven units are more numerous and it is unnecessary to assume a drive efficiency, thus eliminating one possible source of error. It is the purpose of this paper to define and explain the various types of pressure measurements involved in a field test of an axial-flow mine fan, and to further explain the proper use of the Pitot tube when measuring pressures and volumes. DefinitioN of Fan Pressures The two fan pressures most commonly discussed are fan total and fan static pressure, each of which has the same meaning regardless of whether the fan is blowing, exhausting, or blowing and exhausting, as in the case of a fan with ducts connected to both outlet and inlet. Fan total presscre is the amount by which the total pressure of the air delivered by the fan exceeds the total pressure of the air received by the fan. This pressure is a measure of the maximum amount of the work done on the air by the fan that is available for external use.

Jan 1, 1942