Search Documents

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines (USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two for-mulations resulted in stable gels that lasted for at least 12 months in the mine. Semicontinuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both in terms of productivity and enhanced mine safety.

Jan 1, 2010

By Douglas Baker

Zinc concentrates assaying approximately 54% zinc and 30% sulfur are roasted in a suspension type roaster to yield a zinc oxide calcine assaying about 65% zinc and 0.40% sulfur. This calcine is the feed material to the sulfuric acid leaching section of an Electrolytic Zinc Plant. The SO2 gases resulting from the elimination of sulfur from the concentrates are passed through a waste heat boiler for the generation of high pressure steam, cleaned by a baghouse, and delivered to the humidifying tower of a sulfuric acid plant system. The gases are then treated in a mist precipitator for final fume removal and then converted to sulfur trioxide in a three pass contact system using vanadium pentoxide catalyst for the manufacture of sulfuric acid. Waste heat steam is used to power the steam turbine which drives the acid plant blower.

Jan 1, 1970

An approximate rapid design system for tunnel liners and underground structures is presented which permits the effects of structure geometry and stiffness, rock quality in terms of its deformation modulus, and the applied system loading to be entered as data to produce direct designs conforming to stress limitations, optimum reinforcement requirements and restraints on section dimensions. An 'equivalent column' concept is introduced for modelling the rock mass in contact with the structure. Only the rock treatment is given in detail but the results of sensitivity analyses, with reference to rock quality, for a typical liner design are given and these results related to a number of empirical design approaches.

Jan 1, 1976

By C. J. Malek

The CONTOP® smelting cyclone technology is a large-scale and time-proven method which in combination with other technologies (grinding, drying, pyrolysis, etc.) provides for a cost- efficient and ecological disposal of a wide range of waste materials from industry and households. In this report the basic principle of smelting cyclone technology will be explained first. Subsequently, the paper will discuss substantial concepts for the recovery of various remainders.

Jan 1, 1996

By W A. Bardswich

The numerous factors associated with the prov1s1on of satisfactory air conditions in hot and humid Canadian mines are described. The main heat sources are auto-compression and the actual flow of heat from the rock. Temperatures reach 97°F at a depth of 8,100 feet. Various methods used in coping with high temperatures are described, including the use of ice stopes and heat exchangers. Moisture control, desirable air volumes and velocities, sizes of airways and methods of distribution are important considerations. A comparison of the temperatures, humidities and types of airways of two deep mines should prove useful in the design of future ventilation systems. Introduction OUTDOOR temperatures in northern Ontario vary from a low of around -40°F in winter to a high of about +90°F in summer. The average annual mean temperature over a 12-year period was +35°F, with a summer mean of 54 o and a winter mean of 16°. Because of low outdoor temperatures, a number of northern mines must heat fresh air for underground ventilation in winter; others, with high rock temperatures, are faced with a year-round cooling problem.

Jan 1, 1965

By A. Juganda, H. PINHEIRO, J. Brune, N. SANDOVAL, G. Bogin, K. Gallagher, F Wilson

The present work discusses the nuances of scaling and flow similarity to develop a 1/40th scale version of a longwall coal mine. Details on the geometric, kinematic, and dynamic scaling of the physical model are presented and discussed. This works also discusses using a 30% CO2 – 70% He gas mixture as a surrogate for methane. It also presents the implications of various Reynolds numbers (ranging from 7,000 to 140,000) and rotation of the shearer drums in the dynamic representation of the airflow and gas mixtures in the physical scaled model.

Mar 19, 2022

By Bezalel C. Haimson

Anna, Ohio, at the junction of Cincinnati, Findlay and Kankakee arches, has been the site of repeated and sometimes damaging earthquakes. As part of a seismicity investigation near-surface (0.15-1 m depth) overcoring strain measurements were conducted in four limestone and dolomite quarries surrounding Anna, the results of which suggest a complicated regional stress pattern, with changes in the maximum horizontal stress direction from N45ºE to N15ºW. Since such abrupt stress fluctuations are rather atypical in the Midwest and since the reliability of near-surface tests in defining regional stress had not been established, we decided to remeasure the stresses at the same locations but at greater depths (0-200 m) using the hydrofracturing method. Owing to the weak horizontal bedding planes of the Silurian shaly limestones and shaly dolomites and the relatively shallow depths, many of the tests yielded horizontal fractures, providing information only on the vertical principal stress (-0.029 MPa/m depth). However, sufficient tests in each of three testholes resulted in vertical hydrofractures to enable the calculation of all three principal stresses. Within 50-170 m depth the horizontal stresses in all three quarries appear to belong to a uniform regional Stress field defined by the following relations: [']Hmin = 5.1 + 0.014 D; [0] Hmax = 10.1 + 0.014 D, where D is depth in meters. The direction of [O]Hmax within 50-170 m depth is uniform at N70°E (±15º). The hydro- fracturing results obtained at Anna, Ohio are in agreement with the prevailing stress regime in the midcontinent both with respect to magnitudes and directions. The results suggest a possible thrust mechanism for a proposed NW-SE fault along which most of the earthquake epicenters have been located, and a left lateral strike-slip at greater depths. The focal mechanism solution of a recent major earthquake near Sharpsburg, Kentucky, some 200 km south of Anna, also indicates strike-

Jan 1, 1982

By Francisco Leite, Tomi Kouvonen, Bianca Saraiva, Vinicius Miranda, Auã Oliveira

One of the main challenges facing mining engineers is to draw up a plan that can be implemented in a timely manner, taking into account the operational variability of the mine’s production processes. These plans are often drawn up based on deterministic modelling (provided there are a set of known inputs that will result in a single set of outputs), when in truth we are talking about stochastic events (the cycles involved behave like random variables and their nature may be studied and reproduced). The result of using this kind of methodology can lead to non-optimized intuitive choices, which may harm the long-term targets defined by the planning team. Based on this principle, this document investigates the simulation of the rock fragmentation process in an open pit mine to assess the stochastic behavior of the loading and haulage operating cycles. The data assessed by the simulation process were the total costs of these operations in function of the powder factor. Based on a sample set data items, it was possible to check the probability distribution of the event as a Poisson distribution, applied to the loading and haulage cycles. The simulation consists of the repeated sequenced reproduction of these events (Monte Carlo simulation), in order to find the configuration that best fits the loading and haulage operations. By integrating these systems, it was possible to better understand the influence of the blasting in these operations, and as such to reduce the associated costs.

Feb 6, 2023

By C. H. G. Bushell, G. Brown, C. J. Krauss

1N FLOTATION, copper sulphate is used universally for the activation of sphalerite and marmatite and, to some extent, for the activation of other minerals. The copper activated surface readily adsorbs standard collectors such as the xanthates and dialkyl dithiophosphates whereas untreated zir~ sulphide does not. With the host of reagents available, making a mineral float is seldom difficult. The problem is to achieve selective flotation. In zinc flotation, the great value of copper sulphate results from its ability to activate zinc sulphide preferentially to gangue minerals. At the Sullivan Concentrator of The Consolidated Mining and Smelting Company of Canada Limited, the most abundant gangue mineral in the lead-zinc ore is pyrrhotite, and the zinc mineral is marmatite of somewhat variable zinc to iron ratio. For this Cominco study, selectivity between marmatite and pyrrhotite was therefore the most interesting aspect of copper sulphate activation.

Jan 1, 1961

By Redhead Robert J.

"In 1991, the Canadian Council of Ministers for the Environment (CCME) charged its Waste Management Task Group with developing a nationally coordinated strategy to measure, monitor, and achieve the objective of decreasing the generation of waste (solid and hazardous) by50% from 1988 levels by the year 2000.With the encouragement of the CCME, which viewed hazardous waste as largely an industry problem, a committee, the “Industry Action Group”, representing eleven industry trade associations with a strong interest and involvement in hazardous waste was recruited.The Municipality of Markham, Ontario was also recruited (Appendix 1)."

Jan 1, 1996

By Forrest C. Neil, Clint J. Keifer

The pollution of our water supply, Lake Michigan, is a continuing threat so long as our overflows from combined sewers exist. The problems have become even more acute during recent years, due to the increase of paved area- which accelerates and enlarges the flows of storm water. After each storm, mixtures of raw sewage and storm water spill into our waterways. If the storm is too large for the drainage systems, the mixture backs up into our streets and basements. Under severe conditions, it may even become necessary to open the locks, and discharge the polluted water into Lake Michigan. Consider the scope of the problem, as shown in Figure 1. The area in which combined sewers exist is 375 square miles, located in the central parts of Chicago and 49 suburbs. There are an estimated 640 overflow outlets to the waterways, each requiring attention. The capacity of outlets tributary to the waterways has increased dramatically over the years. Each time a pocket of upstream flooding is drained into the channels, the problem of its rapid disposition increases. Another difficulty is that the bottom of our waterways is covered with a blanket of accumulated sludge, ranging in depth up to 3-feet. This material harms the water quality by depleting the supply of oxygen dissolved in the water ... a final

Jan 1, 1997

By Arash Khosravifar Ph. D. P. E., Thomas Torkelson P. E., Milad Souri Ph. D. P. E.

Kinematic demands from lateral ground deformations can be a major cause of damage to maritime and highway transportation structures such as wharves, piers, and bridges. These kinematic demands are different from the ground deformations in the free field in that the resisting forces from piles will reduce the ground deformations to some extent (i.e., pile pinning effect). Current design codes for wharf structures allow the beneficial resisting forces from pile pinning effects to be incorporated in pseudostatic slope stability analysis (e.g., ASCE/COPRI 61-14). While design guidelines that are specifically developed for bridge foundations provide recommendations on how to incorporate the pile pinning effects (e.g., Caltrans 2012), their applicability to wharf structures need to be evaluated. This study uses the results of a large-scale centrifuge test on a pile-supported wharf structure to evaluate the accuracy of available Newmark sliding block analysis in estimating the lateral ground deformations. Pile pinning effects are incorporated based on the approach outlined by Caltrans. The results of this study support the use of existing pile pinning methods that were primarily developed for bridge foundations in maritime structures (e.g., wharves and piers). It was found that median Newmark displacements provide a good estimate of the permanent end-of-shaking displacements and that the median plus 1 standard deviation Newmark displacements provide a good estimate of the peak transient displacements. Design considerations for use in the Newmark sliding block analysis to estimate the kinematic demands on piles are discussed.

Oct 1, 2022

By H. T. Green, R. M. Brick

True stress-strain data on alloys of pure iron with up to 2.4 pct Al were obtained in the temperature range +100° to —185°C. Alumi-num was found to reduce yield and flow stresses of iron at low temperatures but to have little or no effect on ductility. The effects of temperature and composition on strain hardening are discussed. SEVERAL independent studies of the behavior of high purity iron binary alloys at low temperatures are now in progress in attempts to evaluate systematically the variables affecting the low temperature brittleness of ferritic steels. This paper reports the results of one such investigation in which the tensile properties of aluminum and aluminum plus silicon ferrites were measured from 100" to —192°C. True stress-natural strain data have been obtained in order to evaluate as many as possible of the parameters which describe the behavior of the materials involved. In comparable studies at the National Physical Laboratory in England, iron and iron alloys of high purity have been produced' and tested at subat-mospheric temperatures.' True stress-natural strain curves were obtained there also. The purest iron contained 0.0025 pct C and 0.001 pct O and N. Even this, as normalized at 950°C following hot rolling, showed little ductility at -196°C. The grain size was ASTM No. 3, and the room-temperature yield strength was 17,800 psi (which seems too high for pure iron). Some of the NPL irons contained considerably more oxygen and demonstrated intergran-ular fracture at —196°C. The authors2 carefully differentiated between intergranular fractures associated with excessive oxygen content and transcrys-talline cleavage with little ductility encountered at —196°C in the purer material. The cleavage stress was half again as great as that associated with inter-granular fracture. Test Material, Preparation, and Procedures Of a number of Fe-A1 alloys produced, eight were considered to be sufficiently pure for testing. Partial chemical analyses (Table I), low observed yield points, and high ductilities indicate these alloys to be comparatively pure for vacuum-melted irons of sizable ingots, 5 Ib or more. To produce the binary Fe-A1 alloys, electrolytic iron was melted in air, cast into slabs, and rolled to strips 0.010 in. thick. These strips, joined into a continuous ribbon and wound into 2 1/2 in. diameter spools, were subjected for four weeks to a moving atmosphere of purified dry hydrogen in a stainless-steel tube at 1050" to 1150°C. Charges of these spools were melted in beryllia crucibles under good vacuums (1 micron), and aluminum (99.97 pct Al) was added to the melts. Compositions of these alloys are recorded in Table I. The ingots were hot forged and then cold rolled at least 65 pct to 3/8 in. rods which were vacuum annealed to the desired grain size, approximately ASTM No. 4, prior to machining into tensile test bars. All tensile specimens had gage sections 1 in. long, with a fillet of 1.5 in. radius to the shoulder. Gage diameters were 0.250 in, except for a few rods where additional cold work required use of a 0.200 in. gage section. After machining, 0.002 in. was removed from the gage diameter using 240, 400, and 600-grit metallo-graphic papers. The final polish with 600 grit left the fine scratches running in the longitudinal direction. By this means, surface metal strained during machining was removed. A few specimens heat treated after machining were similarly reduced 0.004 in. to remove any material affected chemically by the atmosphere during heat treatments, as is discussed in a later section. Tensile tests of the eight alloys at constant temperatures from +100° to —185°C were performed in apparatus which has been described." The essentials include a double-walled insulated metal vessel which contained the liquid heat-transfer medium surrounding the test specimen. A constant temperature was maintained by means of a pyrometer which regulated the pressure of dry air driving liquid air through a copper coil. Temperature variation was less than ±2°C during a specific test. For axial straining, two lengths of case-hardened chain, terminating in simple shackles, loaded the specimen through threaded grips. The lower grip bar passed through a hole in the bottom of the test vessel to which it was joined by a thin-walled

Jan 1, 1955

By Davi Alves Marques

Esse estudo estabeleceu uma relação entre textura em Zircaloy-4 para diferentes reduções obtidas por laminação a frio (30% e 50%), temperaturas de recozimento, no intervalo de cinco minutos a uma hora, assim como análise morfológica da microestrutura da liga. Foram realizadas análises da evolução da textura do material através das figuras de pólo e a partir de medidas de micro e macrotextura obtidas por técnicas de Difração de Elétrons Retroespalhados e Difração de Raios-X. Verificamos que a laminação auxiliou o processo de recristalização da liga, além de influenciar uma textura de plano basal paralelo ao plano da liga.

Aug 16, 2017

By J. Gautam, T. Ong, W. E. Wallace, M. Keane, S. Xing, J. Harrison

"INTRODUCTIONOrganics extractable from respirable diesel exhaust soot particles by organic solvents have been known for some time to be direct acting frameshift mutagens in the Ames Salmonella typhimurium histidine reversion assay (Huisingh, et al). Upon deposition in a pulmonary alveolus or respiratory bronchiole, respirable diesel soot particles will contact first the hypophase which is coated by and laden with surfactants. To model interactions of soot and pulmonary surfactant, we dispersed soots in vitro in the primary phospholipid pulmonary surfactant dipalmitoyl glycerophosphorylcholine (lecithin) (DPL) in physiological saline. We have shown that diesel soots dispersed in lecithin surfactant can express mutagenic activity, in the Ames assay system using S. typhimurium TA98, comparable to that expressed by equal amounts of soot extracted by dichloromethane/ dimethylsulfoxide (DCM/DMSO)(Wallace, et al, 1987). Here we report additional data on the same system using additional exhaust soots and also using two other phospholipids, dipalmitoyl glycerophosphoryl ethanolamine (DPPE), and dipalmitoyl phosphatidic acid (DPPA), with different ionic character hydrophilic moieties. A preliminary study of the surfactant dispersed soot in an eucaryotic cell test system also is reported.MATERIALS AND METHODSSoots D4 and D6 were collected at two different times as scrapings from the exhaust pipe of a diesel tractor-trailer immediately after the engine was stopped. Surfactant dispersions were made by ultrasonic probe sonicating 25 mg of commercially obtained DPL, DPPE, or DPPA into 1O ml of O.85% physiological sterile saline (PSS) for 10 min at 40 watts power. For surfactant dispersions, 2.5 mg soot was mixed into 2.5 ml of the appropriate phospholipid dispersion. Mixtures were sonicated by 40 watts sonicator probe for one min, then incubated in the sonicator water bath for 30 min at room temperature; the mixture was then incubated for one hour at 37C while being rotated continuously. Dilution series were made with saline. For solvent extraction, 2.5 mg soot was mixed into 2.5 ml of DCM and incubated in a sonicator water bath for 30 min at room temperature. The sample was then mixed with 2.7 ml DMSO, placed in a dry bath at 45C, and the DCM evaporated under a stream of nitrogen gas until 2.5 ml of liquid remained. Ames salmonella/microsome assay utilizing TA98 for frameshift mutation was used for mutagenicity testing, with and without S9 activation, as described by Ames et al (1975). Unfiltered sample extractions or dispersions were preincubated with tester cells for 90 min at 37C : 0.1 ml of sample was mixed with 0.5 ml of PSS, or of S9 mixture, and 0.1 ml of an overnight TA98 culture incubated samples were then added to 2 ml of top agar supplemented with biotin and a trace amount of histidine, and overlayed onto Vogel-Bonner minimal media plates. After 48 hours incubation at 37C, revertant colonies were counted. Solvent controls were DMSO, DPL, DPPE, DPPA, and saline. Positive controls were trinitrofluorenone (1 ug/plate), for samples not treated with S9, and 2-aminoanthracene for S9 treated samples (2.5 ug/plate). All samples were assayed in duplicate. Sister chromatid exchange (SCE) assay was performed, following Lett, et al (1981), using V79 cells, of Chinese hamster pulmonary fibroblast origin. Stock diesel sample suspensions were made as 10 mg soot/ml DPL suspension, or 20 mg soot/ml in DMSO. Aliquots of these soot preparations were added to 15 ml of culture medium per sample flask to result in concentrations of 25, 50, and 75 ug soot/ml medium. After 12 hours incubation, 200 ul of 25 uM 5-bromodeoxyuridine (BrdU) was added to each flask. After another 35 hours incubation, 200 ul of 10 ug/ml colcemid were added; and the cells were harvested three hours later. Cells were swollen by hypotonic saline, and fixed twice with methanol/acetic acid, and burst on microscope slides. Cells on the slide were stained with Hoechst 33258, exp"

Jan 1, 1990

By White PJ, Worrad C

The Hunter Valley Coal Preparation Plant and associated materials handling facilities commenced operation in mid 1982. The new plant and coal handling system were designed to integrate with existing mining and preparation plant operations, but also to be flexible to future mining and marketing developments. The system includes: raw coal stockpiles, a 900 tph dense medium/water washing cyclone preparation plant, clean coal stockpiles, a 7.8 km overland conveyor, large finished product stockpiles and a high capacity train loading plant.The plant's development is described with reference to the original planning objectives. Features aimed at providing operational flexibility and performance are emphasised, including the use of; automated stackers and reclaimers, modular plant, distributed PLC control, a single flight overland conveyor, a network of automatic samplers and blending options to assist quality control.Details are also provided of an innovative technique for control of reclaimer rail track forces, stacker and reclaimer anti-collision systems and the use of DC injection braking.

Jan 1, 1985

By C. L. Dake

AN insistent and steadily growing demand is evident for the broadening of undergraduate curricula in engineering. Among suggested additions are training in public speaking, report writing, business law and contracts, accounting, finance, money and banking, scientific management, economics, social and labor problems, psychology, and ethics. The demand for these subjects comes from the older engineers and from the industries that employ our graduates. Of course, many of the men who suggest such changes are influenced largely by their personal needs and contacts, but the demand is sufficiently widespread to merit serious study by educators. In fact, many educators themselves concur in the proposals for broader training. These matters were examined intensively a few years ago in an exhaustive study of engineering education. Opinion at that time was rather strongly against any profound change. Since then, however, the whole economic system has undergone violent disruption. Even if recommendations made a few years ago were appropriate to the conditions then- obtaining, the enormously changed conditions of the present make advisable a further careful study of this problem. In recent years, mergers, to reduce costs, have sharply limited the number of engineers employed and have thereby intensified the struggle to secure positions. In this stiffer competition, engineers with the most adequate training undoubtedly fare the best.

Jan 1, 1934

By M. J. Adam

As part of its research programs, the Bureau of Mines is investigating the partitioning of complex sulfide minerals to simpler sulfide phases by sulfidation reactions. Partitioning in this manner can afford opportunity to improve selective extraction of mineral constituents of value. This report describes research involving the sulfidation partitioning of the mineral pentlandite, which is an important source of Ni in primary production. For the laboratory studies, the pentlandite was synthesized in nominally equiatomic proportions of Ni and Fe. Elemental Ni, Fe, and S powders were blended, compacted, and sealed under reduced He pressure in vitreous silica tubes. The tubes were heated under controlled conditions at SOD? C for 24 h. The product was verified by X-ray diffraction and chemical analysis to consist essentially of (Ni,Fe)9S8. Small samples of the (Ni,Fe) S were encapsulated with sulfur in silica tubes at reduced He pressures and heated for 1 to 24 h at specific temperatures between 400? and 600? C, both below and above the boiling point of sulfur (_445° Cl. Reaction rate increased with temperature. Within this temperature range, partitioning to individual Ni and Fe disu1fides proceeded to essential completion according to the reaction

Jan 1, 1988

By AIME AIME

NATURE was in a smiling mood on December 18, 1883. On that day, Chester Alan Fulton, the sixty-first President of the American Institute of Mining and Metallurgical Engineers, was born, and she endowed him with every good quality within her reach - looks, physique, intelligence, and character. Brought up in the valley of the Hudson River, with the mighty Palisades which make it the "Rhine of America," he has lived up to his early promise - as a man, as an engineer and as a friend.

Jan 1, 1943

By B Stump

Reliable particle size analysis in minerals processing plants is a critical factor to the economic return of a plant. As recovery of valuable minerals is compromised for particles outside the optimal size range, effective and reliable particle size analysis is more crucial than ever, particularly in the current upswing of the global commodities market. Inefficient particle size analysis can lead to excessive over-grinding, thereby significantly increasing energy consumption and reagent costs, whilst negatively affecting process operation, thickening capacity, water recovery and tailings disposal.Australia’s first installation of a particle size analyser in Iron Ore has been monitored with great interest by the industry. Previously, manual size sampling at Rio Tinto’s Paraburdoo fines processing plant involved off-site sample analysis, with a turnaround measured in days. The Outotec PSI® 500 particle size indicator, commissioned in July 2009, takes approximately three minutes per line at site.The paper will include details on the following:• plant description,• sampling design,• PSI® 500 analyser functionality description, and• key learnings from site.

Jul 11, 2011