Search Documents

By N. Champigny

The geostatistical estimation of the reserves of an ore deposit is highly dependent on the quality and stability of the variograms of the sample grades. Gold deposits commonly show a skewed grade distribution. The few high grades at the tail end of the distribution produce unstable variograms that are difficult to model. If these grades are cut to a lower grade value or removed, more stable variograms are obtained. However, outlier grades may make a deposit economically viable, and their cutting or removal should be treated with caution. To reduce (but not to eliminate) the effect of high grades, a transformation of the raw data can be performed. Most commonly used transformations are: logarithm, gaussian anamorphosis, rank and indicator. Variograms of the transformed grades are resistant to high grades and present a clear structure. The weak point of data transformation appears when grades are estimated by kriging; the estimates are very sensitive to slight variations in the parameters of the back-transformation. More robust variogram estimation procedures can also be used, but often these procedures are not suitable for skewed grade distributions as they are based on an assumption of a contaminated normal distribution. The Porgera gold deposit in Papua New Guinea has a highly skewed grade distribution, with grades ranging from 0.01 to 3500 g/t and a coefficient of variation greater than 5. For the geostatistical estimation of the high grade zone of the deposit, the influence of the high grades was quantified by calculating and comparing the following variograms: raw grades, raw grades with the highest grades removed and transformed grades. The study confirmed that there is no general method for handling high grades in a geostatistical reserve study. Several methods should be tried to quantify the influence of high grades.

Jan 1, 1991

By JOHN S. HEARDING

ON the Minnesota Ranges, 600 million tons of material have been moved in the past three years to produce 172 million tons of direct-shipping iron ore. Increasing wage rates and cost of equipment and supplies, coupled with the larger amount of waste material to be moved in comparison with the quantity of ore make it imperative that tile industry adopt all practices and methods which will enable it to move earth at progressively lower costs. Drilling. Prior to and during the war practically all blastholes drilled were 6-in. in diameter and put down by drills using strings of tools weighing from 2000 to 3000 lb. Present trends indicate that heavier drilling equipment making 9-in. holes wit11 3000 to 6000 lb tools will be more economical. Holes up to 12 in. diameter will be made with this equipment. Forging and hardening practices for bits to increase footage is receiving attention. One manufacturer expects to market 9-in. bits having sintered carbide inserts in the reaming and cutting edges. Oxygen and oil to burn holes in the rock are being tested for making blastholes at a considerably greater speed than can be obtained with a blasthole drill on the same size hole. To dale, however, the cost has been prohibitive.

Jan 1, 1949

By Arun Vathavooran, Adrian Singh, Michael Fletcher, Rainer Imhof

The Imhoflot G-Cell, a new development in the pneumatic flotation technology (which incorporates centrifugal forces in the separating vessel) is a recent innovation in the mineral processing world. The G-Cell was invented by Dr Rainer Imhof and commercialised by Maelgwyn Mineral Services Ltd. In a short time span a number of plants and units have been successfully commissioned in the mineral processing industry. In addition, a number of industrial G-Cell flotation plants are in the process of construction for the purpose of coal preparation and environmental remediation. In this paper two industrial installations have been highlighted together with a pilot plant test programme investigating ultra fine flotation recovery for a base metal operation.

Jan 1, 2007

By Kurt Tischler

This paper presents the field experience of Siemens with regard to Gearless Drives in the mining industry ? We consider the elapsed production hours of Siemens Gearless Drives to be extensive enough to provide a reliable estimation of availability calculated on the basis of data representing repair time, downtime, and operating time. The users of Siemens Gearless Drives confirm an availability of more than 98% after exclusion of some major issues. The paper addresses all of these major issues of Siemens Gearless Drives, describes successfully applied corrective measures, explains the influences on the design of the drives, and lists the downtimes associated with each of these issues.

Jan 1, 2012

By W. M. Armstrong

THE GROWTH of the major iron and steel industries on this continent and in many European countries was based on the use of as-mined, high-grade, lump iron ores and on the availability of metallurgical coking coals. The modern coke-fired blast furnace was developed for such materials and is one of the most efficient of ail pyrometallurgical processes. Most of the impure pig iron produced by blast furnaces was converted to refined steel by the Bessemer process in the years prior to 1900 but, when large quantities of low-cost steel scrap be-came available, the more flexible open hearth process was adopted by most large steel producers on this continent. Although this pro-cess has many desirable metallurgical features, the thermal efficiency is low, the capital cost is very high, and the method of charging scrap steel is inefficient by modern standards of material handling. In recent years several conditions have arisen which have stimulated the development of many new pro-cesses and the re-examination of the existing smelting and steelmaking techniques.

Jan 1, 1958

By César Ugaz Castañeda, Paulo Fernández Alvarado, Richard Sotomayor Oblitas, Rocke Enríquez

Mina El toro has been making substantial changes in its operation to improve its social impact and productivity. Because of the use of gasified emulsions and electronic initiation system, it was possible to mitigate vibrations and carry out massive blasting, increasing its production by 4.2% and minimizing complaints from communities.

Feb 1, 2020

By T. L. Joseph

IT is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man's thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life's work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe's pioneer work in the field of metallurgy. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that under- lies the production of steel. Although Dr. Howe's work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book1 on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe's ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blast- furnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1946

Unrelieved residual strains can influence the states of stress in rock masses. If cheap, stable structures are to be constructed in Tock in which large pressures are exterted by unrelieved residual strains, the pressures must be either utilized or neutralized. A photoelastic technique has been used to show that the release of residual strains in rocks is influenced by the mechanical properties of anisotropic rock fabrics. The relationships between directions of residual strain release and the attitudes of minor geological structures have been determined. For engineering design purposes it is possible to estimate the principal stress directions in rock containing unrelieved residual strains if the attitudes of such minor geological structures as foliation planes, lineations, and joints are known.INTRODUCTIONQuarry workers have long been aware that near-surface rocks may be highly stressed. In many cases the stresses are too large to be the result of gravitational loads. Dale (1923, pp. 34-35) gives many instances of deformation produced by the violent release of residual strains in quarry rocks. Coates (1963) has described powerful rock bursts and cases of rock deformation underground implying the existence of much larger stresses than are likely to result from present-day gravitational loads. The only explanation is that pressures of up to several thousands of pounds per square inch may be caused by unrelieved residual strains in rock.Instruments have been developed for measuring states of stress in rock masses. Most stress determinations in rock have been made on the assumption that rock behaves as a simple elastic material. It is now known that rock is a...

Jan 1, 1964

By Yuanbo Zhang, Zhixiong You, Li Qin, Guanghui Li, Tao Jiang

Low-grade manganese oxide ore is generally characterized by high iron content. In this work, sulfidation roasting of an iron-rich manganese oxide ore with elemental sulfur was characterized. The experimental results indicated that manganese dioxide can be selectively reduced over iron oxide by using elemental sulfur. The manganese phases in roasted product included low-valence manganese oxide, manganese sulfide and manganese sulfate, while those of iron mainly depended on the sulfur addition. Iron oxide would only be reduced or sulfidized at larger sulfur additions. The effect of roasting temperature and S/Mn mole ratio on the phase transformations was also investigated; extractions of Mn/Fe by sulfuric acid were evaluated. An extraction of Mn greater than 95% was obtained while that of Fe was controlled less than 10% under the optimal conditions.

Jan 1, 2016

By T. Marin, J. E. Seccatore, M. Cardu

The most energy-intensive process in the mining industry is particle size reduction – comminution. The first phase of this process is blasting to fragment the rock from the initial Boussinesq’s halfspace size. Scientific literature demonstrates that the output of a blast in terms of fragment size distribution can be manipulated by varying the specific charge (powder factor) and charge distribution. This study focuses on the influence of blasting on the internal resistance of the blasted fragments; in particular the influence of the spatial distribution of charges. Small-scale blasts were performed on 14 marble blocks using different powder factors and charge distributions. Three control blocks were fragmented by mechanical means for comparison. The results show the correlations between charge distributions and the specific energy of mechanical comminution. Opportunities for adjusting charge diameter and distribution in opencast blasts to improve the performancet of comminution circuits are discussed.

Aug 8, 2024

By C. R. Edwards

"The Cigar Lake project will develop the world’s second largest high grade uranium deposit. The Cigar Lake Phase 1 orebody contains approximately 226 million pounds U3O8 at an average grade of 20.7% U3O8. The mine, to be operated by Cameco Corporation, will use a unique water jet boring mining method to cut previously frozen ore. A distinctive ore handling design is required to handle the high grade ore slurry exiting the mining machines. The ore will be crushed and ground underground, with the ore slurry then pumped to surface. Loaded into purpose-designed containers on tractor-trailer units, the ore slurry will be trucked to Cogema Resources Incorporated’s McClean Lake mill. McClean Lake will leach all of the ore. Forty-three percent of the resulting uranium solution will remain at McClean Lake for processing into yellowcake. The other 57% of the uranium solution will be shipped to Cameco’s Rabbit Lake mill for processing into yellowcake there. Detailed design for the Cigar Lake project is now underway. Barring regulatory or market delays, production could start up as soon as early 2005.INTRODUCTIONThe Athabasca Basin in northern Saskatchewan hosts a number of large uranium mining and milling operations, including Cluff Lake, Key Lake, McArthur River, McClean Lake and Rabbit Lake. (Edwards 1988, Edwards 1992, Fielder 1998, Edwards and Oliver 2000, Edwards 2001) The latest project in the Athabasca Basin is the Cigar Lake project."

Jan 1, 2002

By J. R. Hauber, N. R. Borch

A study uras made on the creep behavior of cast and extruded SR grade beryllium. It is shown that, for stresses below about 1000 psi in the temperature range 760" to 85o° c, the creep behatior is nearly exactly described by the Nabarro-Herring mechanism. The activation energy is apparently that for self-diffusion, 42 2 kcal per mole, below 1000 psi, but it rises to 88.6' kcal per mole at higher stresses. The slress exponent is 4.5 at the higher stresses. Tertiary creep in this material is clearly related to void formation apparently caused by grain boundary sliding. BERYLLIUM is becoming an increasingly important technological material. A search of the literature has revealed a lack of fundamental studies on the creep of beryllium. This investigation was therefore undertaken to gain insight into the creep behavior of this material. EXPERIMENTAL PROCEDURE Tensile creep samples were prepared from cast and extruded SR grade beryllium. The vendor's chemical analysis of the beryllium tested is shown in Table I. The test specimens were machined as shown in Fig. 1 from i -in.-diam rods. The machined creep specimens were annealed to remove surface damage and to establish a variation in grain size. The heat treatments and their resulting grain diameters are shown in Table 11. The average grain diameters were determined by the intercept method. True average grain diameters were estimated by multiplying the measured average grain diameters by 1.5.' The creep tests were performed at temperatures from 700" to 850°C in a vacuum of 105 Torr or better in a tantalum-element resistance furnace. Loads were applied by an Instron testing machine such that the stress was held constant to within 20 psi. The test temperature was measured by thermocouples on the sample. With one exception the deviation from the desired test temperature was 2"C, and in that case the deviation was 4"C. Elongations were measured by an extensometer within the vacuum chamber which was fastened to the creep specimens at the grooves in the grip ends, as shown in Fig. 1. The precision of measurement of elongation was 1 X loe4 in. The creep tests were begun only after thermal equilibrium had been established in the sample and the extensometer to insure that there was no strain rate component due to transient thermal effects. Two kinds of creep experiments were performed. First, at constant grain size, the effects of varying stress and temperature were studied. In the second set of experiments, the temperature was held constant and the grain size was varied. The activation energy for creep was determined by varying the temperature at constant stress, as described by orn, during the first set of experiments. The variable grain size experiments revealed that creep at low stress apparently occurred by the abarro-errin' mechanism. In all of the creep tests, the stress was held constant only until sufficient strain had occurred to accurately determine the creep rate. The stress was then raised to a new value and the new creep rate determined. This process was reported until tertiary creep occurred. In this manner several data points were obtained from each specimen. The assumption was made that the structure was not changing appreciably between the incremental stress levels. This was verified by reducing stresses to previously tested levels and comparing the creep rates with the creep rates obtained at the lower strains. The re-producibility was within experimental error over strains on the order of 1 pct. EXPERIMENTAL RESULTS A typical series of creep tests is shown in Fig. 2. Primary creep was not observed in any test. Transient creep, which we define as creep rates that are nonlinear with time, was not observed for any change in stress except where tertiary creep occurred. The absence of both primary and transient creep has been previously reported for hot-pressed powder beryllium.= The data for the creep behavior at constant grain size are summarized in Fig. 3. The data show two distinctly different stress dependencies. At stresses below about 1000 psi, in the equation:

Jan 1, 1969

By M. L. Wu

A moderately thermophilic acidophiles strain had been isolated from the bio-heap leaching plant in Zijinshan Copper Mine, and the identification based on the PCR-16S rRNA gene sequence homology analysis with morphologic and physiologic methods was conducted by polyphasic taxono-my and phylogeny research. The results show that the strain by depurated belongs to Acidthiobacillus genus and is considered as Acidthiobacillus albertensis.

Jan 1, 2014

By Kanaan Hanna

The integrity factor approach was developed by the Bureau of nines to assess the stability of mine pillars and has been applied primarily to longwall chain pillars. Recently this approach was applied to a room-and-pillar mine in the Illinois Coal Basin. A special configuration of hydraulic borehole pressure cells was installed in a pillar to determine the in situ strength-and- stress relationship of the coal pillar and to verify the applicability of the integrity factor approach. Results indicate that the integrity factor approach is applicable to the assessment of pillar st6b:lity and nay bs a realistic and effective approach for room-and-pillar mine design.

Jan 1, 1988

By X. Zhu, Chen. L., R. Guru, M. Peiravi, M. Mohanty, L. Ackah, B. Xu

"The overall goal of this study is to develop a suitable flow sheet to extract rare earth elements (REEs) from coal ash. A total of 14 coal samples of different ranks were examined for REE concentration, and an anthracite coal sample with the highest REE concentration of more than 700 ppm in the coal ash was selected for REE extraction tests. This paper reports on the results of the experimental program completed in the first part of the study, which included hightemperature leaching with nitric acid followed by solvent extraction tests using various organic extractants, namely, tributyl phosphate, Cyanex 572, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and their combinations. A 4×2×2 experimental design was used to conduct a total of 32 high-temperature leaching tests by varying acid molarity at four levels, solids content at two levels and leaching time at two levels. The highest recovery rates of 90 percent for light rare earth elements (LREEs) and 94 percent for heavy rare earth elements (HREEs) were obtained from the optimum leaching test conditions while maintaining impurity recovery to the leachate at less than 40 percent. D2EHPA was found to be the best extractant in this solvent extraction test series, providing an REE recovery rate of nearly 99 percent.IntroductionGlobal demand for rare earth elements (REEs) and other strategic metals is increasing rapidly due to their use in a variety of advanced technological applications, with more than 100 kt of rare earth oxides used worldwide on an annual basis. The United States has less than 10 percent of the world reserves of REE mineral deposits, and in 2013 imported more than 60 percent of its rare earth oxides from other countries, mainly China (United States Geological Survey, 2017). China’s institution of export quotas has significantly reduced supply to the United States, raising the urgency of finding new ways of producing REEs and/ or substitutes. Coal combustion byproducts, which are usually discarded as waste materials, are known to contain REEs in low concentrations that could be extracted with a suitable process flow sheet. This may be a worthwhile route to pursue, considering the short supply of rare earth minerals and the abundance of coal ash in thousands of ash ponds in the United States. More than 110 Mt of coal combustion byproducts are produced annually in the process of satisfying the country’s need for electricity (American Coal Ash Association, 2016), and less than 50 percent of these byproducts are being successfully used in various applications, with the remainder dumped as waste materials in landfills and ash ponds."

Jan 1, 2017

By J. H. Canterford

The nickel industry in Australia has followed the general pattern apparent in many other regions - lots of ups and downs, successes and failures, but always plenty of challenges. Some of these can be attributed to local geographical and infrastructure factors, others to a healthy mix of corporate good luck and management countered by decisions that, in retrospect, were less than optimum. The roles of several entrepreneurs have certainly added plenty of spice! In terms of processing technologies, there was an initial heavy reliance on the use of "off the shelf' commercially proven processes such as ammonia leaching of concentrates and mattes, and flash smelting. Over the past decade there has been an increasing dominance of plant modifications and process technologies that have been developed "in house" in order to enhance project economics and exploit lower grade and more complex resources. This presentation provides an overview of the past 40 years of the major developments in the Australian nickel industry and concludes with some guesses as to where we will be in another decade or so.

Jan 1, 2005

By E. R. Hoskins

The Gulf Coast States ranging from South Texas to Alabama contain vast resources of lignite ranging in energy content from about 4000 to 7000 Btu/lb (as-received) with sulfur content ranging from about 0.5 to 2 percent. Currently, the strip mining rate is about 35 million tons per year in Texas and essentially zero in the other Gulf Coast states. Estimates of future mining rates are as high as 310 million tons per year by the year 2000 with 240 being in Texas. In this paper, we examine the life cycle of the surface mineable lignice based on the most recent estimates of surface mine recoverable resources with two scenarios. The first indicates that a 310 million tpy rate could be sustained for only 15 years while the second scenario suggests that the 310 million tpy could be sustained for 25 to 30 years. If lignite resources are required beyond those that are surface mineable, the deep basin lignite will be developed. Five strategies for developing deep basin lignite are discussed.

Jan 1, 1983

By M. Kucharski

The model of the Outokumpu direct-to-copper process deals with a steady-state process the parameters of which do not depend on time. To give a prediction for the process outcome, "a modified black box" method, which ignores most of the chemical reactions in the furnace, was used. This method takes input and output parameters into consideration. The presented model describes the Outokumpu direct-to blister process in the form of the set of linear equations which give mass and enthalpy balances as well as the distribution of elements between blister copper and slag. However, only major substances where quantities in the feed charge exceed a certain level (for example 0.5 kg/ lMg of smelted concentrate) are taken into consideration. Minor elements are distributed among slag and metal phases in a different way. Some of the equations are derived from distribution coefficients. The value of distribution coefficients can be calculated from plant production data.

Jan 1, 2007

By Pan Zhao, Yan-Nan Wang, Fei-Long Liao, Can Cai, Kai-Song Wu

"What are the basic physical parameters and main geometric parameters that are capable of representing the microscopic characteristics of rock? How can these parameters be used to accurately describe the macroscopic mechanical behavior of rock? With such questions in view, and based on the microcosmic structure analysis of rock slices, this paper presents a rock skeleton-pore structure model, holding that rock's mechanical behavior depends on the properties of rock skeleton materials and the form, size and distribution pattern of pores. According to rock stress and deformation behaviors, and in line with the skeleton-pore structure model, an essential mechanics theory for rock is advanced. The assumption that the skeleton materials are incompressible in volume and an introduction of logarithmic strain, generate the relation between porosity and apparent strain. Then, the notion that positive damage and negative damage are represented in terms of porosity is put forward; threshold value of porosity is derived by the damage threshold value of apparent volume strain; a general damage variable of rock is obtained; eventually, with the skeleton-pore model as the groundwork, a global damage constitutive equation is developed, which, with definite physical significance and material parameters to be easily determined, is convenient to apply. It has been proved that the results calculated with this new equation are well in agreement with experimental results.INTRODUCTIONRock is a form of material that contains pores, cracks and skeletons. Skeletons are composed of particles and cements. Pores or cracks within rock actually undermine the assumption of material continuum in solid mechanics. Hence, grave errors — or even false results — are inevitable if some solid mechanics theory is quoted in the discussion of rock mechanics. Many researchers in the field of rock mechanics have attempted various remedies, but the outcome is far from satisfactory — a mechanics theory for rock, in its true sense, has not been established."

Jan 1, 2015

By A Sadri, S Smith

In the metal and mineral industry, different empirical techniques are used to estimate the remaining thickness of the lining within an operating furnace. The disadvantage and costly factor when using these methods is that production needs to be halted. Hatch has developed an accurate and reliable technique based on stress wave propagation principles to determine the condition of the remaining lining whilst the furnace remains online and operational.The technique involves test data collected and compiled to generate 3D imagery used to assist operators and maintenance planning personnel with valuable information showing areas of metal penetration in the lining, remaining lining thickness, exact location of voids, cracks, poor contacts and deterioration due to chemical attack. In this paper, the principals of the AU-E technique will be explained both theoretically and practically. In addition, the use of ultrasound technology for determining the condition of copper cooling elements will be briefly addressed.

Jan 1, 2006