Search Documents

By Daniel A. Thome, Robert C. Janke

"Installation of permanent soil nails through distressed mechanically stabilized earth retaining walls is a cost effective and aesthetically pleasing solution when using the appropriate equipment and drilling methods for installation. A forensic investigation was performed on an existing mechanically stabilized earth retaining wall to determine the possible causes for the excessive horizontal displacements and visual structural flaws found along a portion of the wall. Reports concluded that the visual shifting was due to a number of factors including improper drainage in the vicinity of the wall and unsuitable compaction of the backfill material. Conceptual designs were proposed to the owner and the installation of permanent soil nails through the existing precast panels was determined to be the most practical solution. A total of ninety-three permanent soil nails were installed to lengths of up to 40 feet (12 m) through sand backfill and silty day fill using a hydraulic rotary percussion drill attached to a tract mounted excavator.IntroductionThe Illinois State Toll Highway Authority awarded Contract RR-03-5144 in the summer of 2004. Construction work for the project consisted of the rehabilitation of two existing concrete culverts and approximately 100 linear feet (31 m) of mechanically stabilized earth (MSE) retaining wall. The retaining wall is located below the southbound lanes of the Tri-State Tollway near the intersection of Federal Highway 41 in Wadsworth, Illinois as shown in Figure 1.Reports were prepared by Applied Technologies in cooperation with Giles Engineering Associates to determine the condition of the MSE wall and recommended conceptual designs to extend the service life of the wall.Nicholson Construction Company (Nicholson) wasselected as the design-build geotechnical subcontractor to install the recommended permanent soil nails through the existing precast concrete panels of the MSE wall. Rehabilitation of the wall involved the installation of ninety-three permanent soil nails through the existing wall, along with soil nail verification tests and proof tests on production nails."

Jan 1, 2005

By T. M. Ruff, W. G. McCoy, M. J. Beus, S. Iverson, W. Hasz

Technology to enhance safety during mine hoisting has been developed by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Assessment of current hoisting technology suggests that monitoring conveyance position and load directly from the skip or cage top offers several significant safety advantages. Wireless data transmission schemes and a package consisting of sensors, batteries, and a charger mounted on the wire rope and skip have been developed. A state-of-the-art automated hoisting test facility was constructed to test the concept in a controlled laboratory setting. Field tests in a fill-size shaft are underway.

By Hong Li, Chenxiao Li, Wenwen Mao, Hua Lu

Directly charging limestone into slag in BOF is a newly emerging technique which broke through the traditional BOF slagging principle. It is necessary to study the decomposition behavior of limestone in converter slag during BOF steelmaking. FeOx, SiO2, MnOx and pre-melting slags were mixed with limestone according to different quality proportion to simulate the environment of limestone in converter slag. TG-DTA results indicated that slag with individual component, including FeOx, SiO2 and MnOx, all had obvious effects on reducing the decomposition temperature of limestone. Pre-melting slags with multiple components had further reducing effects than individual component. XRD results showed converter slag component would react with decomposition product of CaCO3 and generate solid solution or oxide, reducing the activity of CaO and the decomposition temperature of CaCO3.

Mar 1, 2017

"Decreasing gold-in-ore grades is one of the main drivers of poorer productivity and rapidly escalating unit costs. Grinding costs, water use and reagent consumption are all intimately related to the ore grade processed. Various pre-concentration technologies have been developed that can be applied at various stages of crushing prior to ore grinding. This paper will review the amenability of ores to coarse particle barren gangue rejection for fine crush sizes in the pumpable particle size range (i.e., particles between 5 mm and 0.3 mm in size). The liberation of oxide gangue achieved during crushing is evaluated by proxy using sink-float analysis and the deportments of gold, sulfur, and arsenic into sinks and floats are monitored. Amenability of gangue rejection by continuous gravity separation is evaluated after various crushing modes (vertical shaft impact crushing, cone crushing, and HPGR crushing). The potential to identify coarse particle mineral association and liberation using three-dimensional x-ray computed tomography will be discussed.INTRODUCTIONThe aim of research in this area is to explore some of the attributes which make some ores amenable to preconcentration, or rejection of a significant component of the feed mass to tailings at a coarse liberation size. Characteristics such as ore type, mineralogy, breakage pattern, particle shape, and liberation characteristics may need to be examined to identify amenability to pre-concentration amenability.It is intended to focus on continuous gangue rejection in the pumpable size range (0.3–5.0 mm) as this remains one of the key opportunities to reduce processing costs through a combination of techniques including screening (for mineral differentiation rather than size classification only) and gravity separation (using jigs). This is to be contrasted to conventional preconcentration as performed with automatic ore sorters."

Jan 1, 2016

By Hitendrabhai S. Dewangan, Dr. Aashish A. Mehta

Pile foundation is widely used in construction of marine structures. In offshore & marine piling work, drilling/boring supporting fluid is used to stabilize the borehole (excavation) prior to tremie concrete. The poly-fluid is a synthetic drilling granular polymer characterized by high molecular weight.it is mainly used for the preparation of stabilizing and lubrication mud in drilling of deep foundations. Disposal of polymers after using it into the sea, pollutant the sea environment, which may be harmful for living organisms inside sea. To reduce the pollution in offshore/Onshore, it is essential to take the precautions during flushing operation with proper recycled, reused & it’s Disposal. To provide economic and environmental solutions, used slurry was treated with addition dose of fresh material/polymers. The amount of fresh materials/ Polymer to be added can be decided based on (viscosity, density and pH value) test results. Finally, initiate water flow and air agitation as required. Run the tests on the re generated slurry before transferring to storage tank. Also, after storage, polymers will be reused for next operation. Moreover, mud wastage coming from borehole will also be disposed at suitable dumping places.

Sep 1, 2022

By Paul H. Johnson

Chemical mining may be defined as the in-place extraction of metal values from ores located within the confines of a mine (that is, broken or fractured ore, stope fill, caved material, or ores in permeable zones) or ores located in dumps, prepared ore heaps, or tailing ponds. The term solution mining has, in general, been used to mean the in-place dissolution of water-soluble mineral salts with leach solutions. Chemical mining is presently in its embryonic stage. Basic research needs to be done to understand the influence of physical and chemical factors in chemical mining, and applied research needs to be done on both a small and a large scale to develop practical techniques of field practice. The areas of research include the following: (1) Leaching chemistry, the influence of physical, chemical, and biological factors in in-place leaching (2) Hydrodynamics of chemical mining systems (3) The development of new, as well as old, leaching agents for use under chemical mining leach conditions (4) The development of new means of contacting fine and coarse materials (with solutions) under static leach conditions (5) The development of new processes for generating and regenerating chemical mining leach solutions (6) The development of metal recovery processes

Jan 1, 1969

By L. B. Pankratz

Heat content measurements were conducted for GaPo.996 and InPo.986 over the temperature range from 298° to 1,100° K, and for In2S2.897 over the range from 298° to 1,200° K. Both the actual experimental data and values adjusted to conform with the stoichiometric compositions (GaP, InP, and In2S3) were reported. Entropy increments above 298.15° K were calculated for the stoichiometric compounds, and heat content and heat capacity equations were derived.

Jan 1, 1965

By W. J. Pearson

"""POTASH"" is a term applied to the compounds of the element potassium (K) and when used in agriculture and industry is ex-pressed in terms of potassium oxide (K2O), regardless of the actual com-position of the compound. When a chemical analysis is made of a fertilizer, the amount of K is deter-mined and then calculated to the equivalent amount of K2O. However, the compound K2O does not exist in nature. Most of the world's potash supply is derived from mineral deposits similar to those in Saskatchewan and New Mexico. However, there is some production from concentrated surface brines such as occur in Searles Lake, California; Salduro Marsh, Utah; the Dead Sea; and from well brines in Micl1igan."

Jan 1, 1960

By L. W. Kelly

The purpose of this paper is to indicate some of the benefits that have been derived in the Zeigler No. 3 mine by using roof bolts under extremely adverse roof conditions J with the thought that much better results could be obtained in other mines with more normal roof conditions by applying some of the practices that were developed in this mine. Some of the benefits that have been obtained in this mine, which will be shown in this paper, are: 1. Increased tonnage per man-shift at the face when roof bolts are used, as compared to the tonnage under similar conditions when conventional timbering methods were used. 2. Increased efficiency of roof bolting by giving the foremen a definite plan to follow. 3. Reduction in delays caused by failures of the trailing cables of loading, mining, and drilling machines. 4. Reduction in the number of accidents after roof bolting was adopted. Inasmuch as the success that followed roof bolting in this mine was obtained under one of the most treacherous roofs in the Middle West, it is reasonable to suppose that correspondingly better results could be obtained under more favorable roof conditions by using the same procedure.

Jan 1, 1952

By W. C. Phalen

"The term ""manjak"" is applied to a variety of bitumen or solid hydrocarbon occuring on the Island of Barbados, West Indies, and in Utah, Cuba, and Trinidad. The deposits on the latter island are found within a distance of three miles of San Fernando, the second largest town on the Island, and within three miles of the famous asphalt lake.In chemical composition, manjak is like asphalt. It is almost pure bitumen. Its melting point is, however, more than 4000F. whereas asphalt melts at 1000F. In composition, it consists of 80 to 90 per cent carbon, the balance being chief¬ly hydrogen, with a small quantity of sulfur. It resembles coal in appearance, is odorless, hard, and brittle. It is found in thin beds between layers of clay.The island of Trinidad is rich in this mineral resource. Its development has as yet hardly begun, and the exportations already made have been with the view of testing out the ma-terial. During 1918, exports to the United States were valued at about $3100, and in 1919, up to October 1, they totaled 41 tons, valued at $1900. Prior to 1900, manjak was mined on a small scale in Trinidad, but for various reasons, very little was done between 1900 and 1913. In the latter year, mining operations were resumed by the Trinidad-Tarouba Oil Development Company, of San Fernando. At the present time, there are five shafts, one of which has reached a 37 foot bed of manjak at a depth of 400 feet. Operations could be greatly extended if there were a greater demand for the material.It has not been found profitable to export manjak from Trinidad in the crude state as the price received, namely $35 per ton, hardly covers mining expenses. These are increased by the necessity for careful and thoro timbering on account of the clay formation.Compounds, made by combining manjak with mineral oil command fair local prices which have enabled mine operations to proceed at a profit. Experimentation is still in progress with different mixtures of manjak and oil for various purposes. The manjak, recently sent to the United States was for the purpose of ascertaining whether American oils would be more economical and useful for mixing with the manjak than the Trini¬dad oils. It is the plan to erect a plant very soon for the manufacture of a variety of manjak paints and compounds.Manjak is rapidly increasing in use, particularly in connection with the oil industry. It is produced in close proximity to the oil wells in Trinidad. It is boiled with oils at high temperatures and converted into compounds and paints for nearly every purpose where a preservative is needed, for example, on pipe lines, boilers, chimneys, and miscellaneous iron ware, machinery, etc. It is usually applied in the liquid state, hardening into a tough, rubberlike coating. It has low viscosity, and is not affected by ordinary heat. It makes an excellent insulating material and is impervious to both air and water. In hot and damp climates, like that of Trinidad where pipe lines quickly deteriorate, their life has been pro-longed for extended periods when painted with this material."

Nov 1, 1919

By G. Van Weert

In the spring of 2010 double refractory ores from historical stockpiles were processed through Barrick's Goldstrike pressure oxidation facility, thereby providing preg robbing feeds for a variety of metallurgical testwork. This paper describes the effects of amount, type, place and time of addition of activated carbons on CIL gold recovery and shows that native carbon in plant PDX'ed discharge solids can still preg rob gold loaded activated carbon.

Jan 1, 2011

By Boyle L. A

A positive displacement pump is being dev eloped for pipeline transportation of coking coal to a -50 mm export specification, at a con- centration and velocity which will allow trans- portation in the plug flow region, minimising degradation of the particle structure, and pipe= line friction losses which will be lower than with turbulent or laminar flow. Pump operation is by hydraulic powered free pistons in a rota- ting cylinder block, with cylinders overlapped by stationary inlet and discharge ports in a water lubricated and sealed rotary valve. Before this development coking coal was not considered suitable for transportation in slurry form, for the valves in the double act- ing duplex piston pumps used for slurry pipe- lines, cannot be divorced from the slurry and require that the solid material must be reduced to a fines'consistency before introduction into the pump suction. The hydraulic transportation of 10 million tonnes of -50 mm coking coal, 50 km from the Bargo area west of the escarpment to an offshore shiploader at Port Kembla is feasible. Study shows that economic factors alone would dictate that the development of a pumping system for long distance transportation of coking coal is necessary. The greatest impact from the slurry transportation of coking coal would be the

Jan 1, 1976

By Gerald H. Luttrell, Joe Shoniker, Jaisen N. Kohmuench, Christopher J. Barbee, Michael J. Mankosa

The HydroFloat technology was specifically developed to upgrade phosphate sands that are too coarse (>0.6 mm) to be efficiently recovered by conventional flotation methods. In this novel process, classified feed is suspended in a fluidized bed that has been aerated using an external sparging system. The air bubbles selectively attach to particles that have been made hydrophobic through the addition of a fatty acid collector. The teetering effect of the fluidized bed forces the low-density bubble-particle aggregates into the overflow, while hydrophilic particles are rejected as a high solids content underflow Since the HydroFloat is actually a density separator, the process can treat much coarser feeds than would be possible using traditional flotation processes. In addition, the high solids content of the teeter bed promotes bubble-particle attachment and reduces the cell volume required to achieve a given capacity. This paper presents test data from ongoing pilot-scale trials of the HydroFloat cell in the phosphate industry.

Jan 1, 2002

By Robert A. Pimentel

Dust is still a major problem in increasing production from longwall faces. Over the last decade, significant improvements have been made in the development of techniques for reducing dust exposure on conventional and continuous sections. But virtually no improvements have been made in dust control on longwall sections. It is true, that there are many more continuous mining sections than longwall sections in the United States and that the number of workers overexposed on continuous miner sections is much larger than the number on longwall sections. However, the problem on continuous miner sections appears much easier to solve and, in fact, we believe that the techniques are available to get virtually all continuous miner sections in compliance. The problems on longwall sections are much more elusive. Also, the number of longwall sections in the United States is expected to increase during the 1980's. Thus, dust control on longwall sections remains a formidable and important problem. Companies operating longwall sections with a dust problem are faced with the tasks of having to quantify the various dust sources, of selecting proper techniques to reduce the problem, of implementing the techniques and of evaluating their effectiveness.

Jan 1, 1983

By F. M. Lewis, J. F. Myers

The selection of the proper type of flotation machine involves the consideration of a wide variety of factors. Under any condition, all types of machines will promote some kind of separation. Obviously, the correct way of deciding which type of machine is best suited for a particular problem would be to set up all types of machines and test them out in a competitive manner, but the vast number of small concentrating plants are unable to make such complete and exhaustive tests. The experience of the authors of this paper indicates that if all the factors involved in any particular problem can be determined, and if all the flotation-machine characteristics are understood, some basis for selection could be arrived at other than actual comparison. This paper is presented to show how the process factors and machine characteristics have been combined at the mills of the Tennessee Copper Co. from studies of several types of flotation machines. At the two mills of the Tennessee Copper Co. in the Ducktown Basin of Tennessee, four distinct flotation separations are made on the complex sulphide ore. Three different concentrates are produced from the ore—in the order of their importance: iron concentrate, copper concentrate, and zinc concentrate. Four different types of flotation machines are used. The selection of these four machines, for the plant operation, was based upon the study and operating experience of the machine units shown in the following list: Fagergren machine; square cell, size 56 inches Fagergren machine; level type, size 56 inches Denver machine; conical disk impeller, size 24 inches Denver machine; receded disk impeller, size 24 inches Minerals Separation Sub-A, size 24 inches Munro-Pearse deep cell, pneumatic Southwestern air machine, Hunt principle To date the study of flotation machines has been confined almost entirely to the rougher circuits. The various cleaning operations, being relatively a much simpler matter, have not been investigated so thoroughly. Table I shows a typical analysis of the two ores as well as of the mineral content.

Jan 1, 1947

By J. F. Myers, F. M. Lewis

The selection of the proper type of flotation machine involves the consideration of a wide variety of factors. Under any condition, all types of machines will promote some kind of separation. Obviously, the correct way of deciding which type of machine is best suited for a particular problem would be to set up all types of machines and test them out in a competitive manner, but the vast number of small concentrating plants are unable to make such complete and exhaustive tests. The experience of the authors of this paper indicates that if all the factors involved in any particular problem can be determined, and if all the flotation-machine characteristics are understood, some basis for selection could be arrived at other than actual comparison. This paper is presented to show how the process factors and machine characteristics have been combined at the mills of the Tennessee Copper Co. from studies of several types of flotation machines. At the two mills of the Tennessee Copper Co. in the Ducktown Basin of Tennessee, four distinct flotation separations are made on the complex sulphide ore. Three different concentrates are produced from the ore—in the order of their importance: iron concentrate, copper concentrate, and zinc concentrate. Four different types of flotation machines are used. The selection of these four machines, for the plant operation, was based upon the study and operating experience of the machine units shown in the following list: Fagergren machine; square cell, size 56 inches Fagergren machine; level type, size 56 inches Denver machine; conical disk impeller, size 24 inches Denver machine; receded disk impeller, size 24 inches Minerals Separation Sub-A, size 24 inches Munro-Pearse deep cell, pneumatic Southwestern air machine, Hunt principle To date the study of flotation machines has been confined almost entirely to the rougher circuits. The various cleaning operations, being relatively a much simpler matter, have not been investigated so thoroughly. Table I shows a typical analysis of the two ores as well as of the mineral content.

Jan 1, 1947

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton, Carla Abarca

"Fine mineral particles are difficult to process by flotation because of their low collision efficiencies with air bubbles. Decreasing air bubble size and increasing mineral particle size through flocculation are the most common approaches to improve flotation efficiencies. Herein we demonstrate that nanoparticle flotation collectors can be engineered to selectively induce fine mineral particle aggregation and promote flotation.Flotation tests of clean fine pentlandite (Pn) and Clarabelle Mill (CBM) rock tails and pyrrhotite (Po) tails that contained significant amount of fine pentlandite have confirmed that the nanoparticles can serve as both collectors and selective flocculants for fine pentlandite. In the case of clean fine Pn, the nanoparticle collectors virtually can float almost all Pn fines. Scoping tests on CBM tails have shown significant improvement in nickel recovery. Addition of nanoparticles as a flotation aid can recover 20% of the nickel contained in the rock tails and 40% of the Pn contained in the Po tails compared to current mill operations giving 0% nickel recovery from rock tails and no Pn selectivity from Po tails. Ongoing work includes attempts to identify optimal strategies for employing nanoparticles in fines flotation.IntroductionFine particle flotation is an industry-wide challenge in mineral processing. Fine mineral particles are difficult to process by flotation because fine particles have low mass and thus low momentum, which results in their low collision efficiency with air bubbles (Dai, Fornasiero, & Ralston, 1999). In addition, fine particles have not only high specific surface area but also more active surface area, which causes high reagent consumption. For base metal sulphide minerals, particle size between 10 µm and 70 µm is a typical range where high flotation recoveries can be achieved with conventional flotation chemistry and acceptable cell residence times. For pentlandite, the flotation recoveries decrease sharply when the particle size is below 10 µm and hydraulic entrainment is the dominant mechanism, giving recoveries proportional to water recovery and no Pn enrichment. (Jameson, Nguyen, & Ata, 2007)"

Jan 1, 2015

By J. Sattarvand, P. C. Augustine

Despite significant safety improvements, the mining industry remains one of the most hazardous occupations globally and the evacuation of Miners, when an uncontrollable incident occurs in the mine, is the best bet to saving lives. However, Human factors/behaviors during an emergency are likely to influence the evacuation performance. Other industries have made a significant effort to determine these human factors that can impede evacuation performance, however, the current state-of-the-art in mine evacuation or self-rescue is that the evacuation route is predetermined, and a static sign is used to direct miners to the predetermined safe location. This method is limited in representing actual conditions that arise in a real emergency, neglecting the different behaviors displayed by humans. As optimization of the evacuation of a mine plays a fundamental role in emergencies and modeling evacuation behavior and movement of miners is a complex task, this research utilized Agent-Based simulations to simulate the evacuation behavior and performance. It was observed that people with the smart evacuation device made fewer mistakes and arrived at the safe place in less time compared to those have no access to the device. The Mathematical model used in optimizing the shortest path to a safe place is also explained in this paper.

Jun 25, 2023

By P. Syrjänen, Lovén. P.

Because geostatistics together with block modeling has not been studied in detail before in the rock mechanics, a two-year research program to investigate the practical use of geotechnical modeling was started in Finland in 1999. According to research work results block modeling gives good estimate of overall rock mass quality but it can not identify individual structures like faults and narrow weakness zones. Weakness zones and faults should be mapped from drill cores, surface mapping, geophysical methods etc. and manually generate 3-D structural model. Rock mechanical 3-D modeling can be used for preliminary stope dimensioning and preliminary reinforcement design. Detailed design needs rock quality mapping from drifts during excavation work. La géostatistique associée à la modélisation par blocs n'ayant pas été étudiée en détail jusqu'à présent dans la mécanique des roches, un programme de recherche sur deux ans visant à examiner l'utilisation pratique de la modélisation géotechnique a été lancé en Finlande en 1999. D'après les résultats des travaux de recherche, la modélisation par blocs donne une bonne estimation de la qualité générale de la masse rocheuse mais elle ne permet pas d'identifier les structures individuelles comme les failles et les zones géologiquement dégradées étroites. Ces zones et failles devraient être cartographiées à partir de carottes de sondages, d'une cartographie de surface, de méthodes géophysiques, etc. et générer manuellement un modèle de structure 3D. La modélisation mécanique des roches en 3D peut être utilisée pour un dimensionnement de la chambre et un plan d'armature préliminaires. Un plan détaillé nécessite l'élaboration d'une cartographie de la qualité des roches des galeries lors des travaux d'excavation. Da man früher Geostatik und Block-Modellieren in der Gebirgsmechanik nicht detailliert untersuchte, wurde 1999 in Finnland ein zweijähriges Untersuchungsprogramm in Angriff genommen. Aufgrund der Untersuchungsergebnisse ergibt das Block-Modellieren eine gute Beurteilung der gesamten Gebirgsmassenqualität, kann jedoch einzelne Strukturen wie Verwerfungen und kleine Schwachzonen nicht identifizieren. Schwachzonen und Verwerfungen müssen demnach aus Bohrkernen, oder mit Hilfe von Oberflächenkartierung, geophysischen Verfahren usw. ermittelt und danach ein 3-D-Strukturmodell manuell erstellt werden. Felsmechanisches 3-D-Modellieren ist für die vorbereitende Abbaudimensionierung und für die vorbereitende Bewehrungsplanung verwendbar. Ein detaillierter Entwurf benötigt die Kartierung der Gesteinsqualität aus den Gesteinsstrecken während der Ausbrucharbeiten.

Jan 1, 2003

By C. K. Leith

THE purpose of these conferences has been to find some basic principles to guide us in the chaos which confronts us, to arrive at elements of a national policy. None such exists, nor, as a matter of fact, have there been any concerted efforts by the public or the mineral industry to evolve one. In the absence of such a policy the administrative agencies of the government can hardly be expected to be consistent or really effective in their handling of mineral problems, domestic or foreign. Basic Facts MINERAL reserves are unequally distributed among the nations. The principal world supplies are grouped around the north Atlantic, and nearly three-fourths of the world's total is controlled politically and commercially by English-speaking people. No one nation has a complete supply of the minerals necessary for modern industry; specialization, reciprocity, and large-scale movements between the nations are inherent in nature's unequal distribution of them. The principal sources of supply are relatively few compared with the nations to be served-a fact which determines broadly certain natural outlines of the world flow. National isolation with regard to minerals can be accomplished only through backward steps in industry and lower standards of living even in the nations possessing the most of the mineral supplies. A certain measure of unified commercial control, international in scope, is a natural consequence of the limited number of the large sources of supply. Mineral supplies for the world as a whole are so large that there is little need for concern about early exhaustion, but every nation has important problems of early exhaustion of particular minerals, which must affect their policies.

Jan 1, 1933