Search Documents

By Michael Twomey, Alastair Torrance, Alan Twomey

Low density explosives have been available in various forms for nearly 20 years. These initially consisted of various diluted forms of ANFO formulated to slow the rate of reaction. One such product that was developed was a blend of ammonium nitrate and rubber. This product uses a coarse fuel provided by granulated rubber to slow the reaction rate of the explosive rather than being a diluted form of ANFO. There has always been a technical difficulty in blending two dissimilar materials without subsequent segregation.

Jan 1, 2011

By Hector Carreon

During fretting, high points or asperities of the mating surfaces adhere to each other and small particles are pulled out, leaving minute, shallow pits and powdery debris. Sometimes these surface conditions are neglected, but they are important in some application such as the aerospace industry. In this research work, non-contacting and contacting thermoelectric power techniques are performed in fretted 7075-T6 and Ti-6Al-4V samples. It has been found that the contacting and non-contacting thermoelectric power measurements are associated directly with the subtle material variations such as work hardening and residual stresses due to plastic deformation produced in the fretting zone but surface topography. Therefore, both techniques could be used for a global characterization of the most relevant fretting induced effects. Potential of these techniques to monitor subsurface changes in other severe surface plastic deformation processes are clearly envisaged.

Jan 1, 2015

By Nagy El-Kaddah

One of the emerging technologies for the production of ultra-clean metals is electromagnetic filtration. The theory and the mechanism of electromagnetic separation of inclusions from molten metal are briefly reviewed along with basic electromagnetic separation systems. This paper focuses on inclusion removal in the induced current separators, with specific reference to a new separator developed at the University of Alabama. A simple analytical model is presented for the analysis of particle separation in such a system. The role of the applied magnetic field on inclusion removal will be discussed. It is shown that particle velocity increases exponentially with increasing magnetic field strength. At moderate field strengths, the velocity of 50 to 100µ inclusions are an order of magnitude larger than those achieved by buoyancy. The separator developed at the University of Alabama is described together with experimental results of laboratory and large scale experiments on purification of molten aluminum. These results demonstrate ?the capability of the system for producing super-clean metals.

Jan 1, 1996

By Philip Thompson

"Carefully planned laboratory test programs provide valuable data regarding the amenability of low grade gold ores to heap leaching. The most common laboratory test is the column leach test. The overwhelming problem associated with this type of test is the limit on the test column height. Most laboratories use a three (3) meter (10 foot) high column as a standard test due to building ceiling limitations, sample size limitations, etc. This paper presents a case study in which an ore sample was tested in a 1.5 meter, a three meter, and a six meter high column to determine the effect of column height on the test results. Other important factors such as sample preparation protocol, preliminary bottle roll testing to determine appropriate crush size, column diameter requirements, and leach solution analyses, are also discussed.IntroductionColumn leach testing has been used for years by many laboratories to determine the amenability of low grade precious metals bearing ores to heap leaching. However, the test work can be compromised by poor planning, misinterpretation of results, and extrapolation of data beyond the reasonable boundaries of the experiment. Preliminary test work should be performed prior to column testing. This preliminary work provides valuable information regarding the response of the ore to cyanidation and aids in the design of the column tests.The sample should be screened into various size fractions prior to testing. The fractions are assayed to determine the gold content of each size fraction and of the overall sample. The most valuable preliminary test is the bottle roll cyanidation test which is usually performed on five kilograms of coarse sample in a large rolling bottle which can accept material up to 50 millimeters top size. The residue from this test is screened at different sizes to determine the distribution of unleached gold in the residue. Comparison of the gold distribution in the leach residue with the distribution of gold in the feed at the same size intervals provides an indication of the appropriate crush size for the sample. The overall gold extraction from the sample at the crush size tested is also determined from these data. Lime and cyanide requirements can also be estimated from this test. The viscosity of the bottle roll pulp and the size distribution of the feed and leach residue can also suggest whether agglomeration of the ore will be required prior to column testing. Ores which contain significant amounts of clays (greater than 5 percent) will generally require agglomeration to prevent plugging of the test column."

Jan 1, 1997

By R. H. Hawkins

AN investigation of the applicability of geophysical methods to north-ern Ontario lignite deposits was undertaken early in 1930 by the Ontario Research Foundation at the request of the Ontario Department of Mines TABLE 1.-Formations Associated with Moose River Basin Maximum System Formation Lithology Observed Correlation Thickness, Ft. Pleistocene Marine clays 150 Glacial till (Minimum Interglacial 30) clay and peat Glacial till Lower Cretaceous or Mattagami Fireclay, sand 138 Kootenay (?) Upper Jurassic. and lignite Devonian (Upper) Long Rapids Petroliferous, 50 Portage and black and gray Genesee shale Williams Limestone and 87 Tully (?) Island calcareous shale Devonian (Middle).... Abitibi River Gray fossiliferous 65 Onondaga limestone Devonian (Lower) ?... Moose Rive- Limestone and 50 gypsum Devonian (Loner) Sextant Arkose, clay, etc. 50 Pre-Cambrian Syenite, granite gneiss, etc. Igneous intrusives. . Lamprophyre dikes cut the Abitibi River and lower formations. (Permission of Ontario Dept. of Mines) and was financed in part from a research grant made by the latter organ-ization. The work to date has included gravitational, magnetic and electrical resistivity studies. The gravitational and magnetic measure-

Jan 1, 1933

By C Vejrazka1

The occurrence of airblasts is one of the principal mining hazards in caving operations between the time of cave establishment and breakthrough of the cave to surface. As such, it needs to be managed continuously and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. The likelihood of an airblast occurring is based on a range of geotechnical factors over some of which engineers on-site only have limited control. However, the impact of an airblast to the underground mine, if it does occur, can be managed by following established safety guidelines for the production from the cave.This paper outlines how the Caving Airblast Simulation Tool in Ventsim was used to determine a risk management strategy for a sublevel and a block cave at a mining operation in Australia. The block cave has a footprint of 14 500 m2 with the extraction level located 1250 m below surface while the sublevel cave currently has a footprint of around 18 000 m2 operating between 660 m and 800 m below surface. Both caves are currently in their early operational periods. The risk analysis provided valuable information for the production planning of the caves including confirmation of extraction ratios for the block cave undercut, locations of airblast walls and maximum allowable air gaps for different muck pile heights to ensure safe operation is achieved.

Oct 12, 2022

By Paul M. Tyler

MILITARY power stems from industrial power and industrial power in turn depends predominantly upon an ample and assured supply of mineral raw materials. It thus becomes the duty of mineral economists to collate the vast array of data and logical deductions in order to reach an unemotional judgment as to the ability of the Soviet economy to withstand the strain of prolonged military action on the modern scale. Russian publications, reports: and official speeches have been laboriously screened and analyzed. Since these are the sources of information for the lower echelons of the Soviet industrial organization itself, they carry factual data that can be pieced together to show the present-day pattern. Apparent contradictions and obvious distortions or omissions can often be rationalized on the basis of observations made by foreign engineers and consultants during the 1930'5 and by checking against the technical literature published before even so-called technical articles were riddled by bombastic and presumptuous claims.

Jan 6, 1951

By McHenry Mosier

Mercury is one of the strategic metals the supply of which has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributes substantially to increased production of mercury in the United States and to consequent accumulation of Governments stock. Other contributing factors were higher prices for mercury and Government loans to operators. The Bureau has undertaken 15 exploration projects, 13 of which have been completed. This work comprised 40,307 feet of drilling arid 35,082 linear feet of sure ace trenching and has indicated commercial ore containing 37,400 flasks of mercury and marginal ore contain¬ing 29,200 flasks - a total of 66,600 flask , equivalent, respectively, to domestic production at 50,000 flasks per year for 9 months , 7 months, and 16 months. Early in 1944, as Government stocks had become adequate, domestic production was gradually curtailed cancellation of Government contracts for the purchase of mercury and Government control of labor and operating supplies.

Jan 1, 1944

As part of remote sensing research on an abandoned mine lands (AML) site in the Colorado Springs, Colorado area, a geographic information system (GIS) database was generated. This GIS database contains information on the locations and extents of abandoned underground coal mines, the geology of the area, subsidence features and degrees of subsidence risk, topography, drill hole locations, and lineaments (linear features) related to subsurface geologic structures. A GIS database allows the reproducible and accurate comparison and analysis of any data sets which geographically overlap and are within the same coordinate system. The database has been released to the public domain so that government agencies, researchers, educators, and the general public can access this coherent database for the purposes of better understanding the study area and GIS technology. Data files and maps are available in formats that are compatible with the GIS software used in the research project and with most CAD systems so that as many people as possible can make use of the majority of the database. This document serves as the data dictionary for the database by providing descriptions and origins of the data files.

Jan 1, 1992

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By Larry G. Stolarczyk

1.0 FRAMEWORK FOR COMPARISON This document describes the decision factors that bear on the selection of the modulation process for the wireless underground medium frequency (MF) communication system. The selected modulation process must satisfy the Bureau of Mines stated objective of improving general communications within an underground mine. The improvement being sought includes the development of a wireless communication technology of measurable benefit to both mine safety and mine productivity. The improvement will allow wireless communications paths to exist between roving miners. The wireless communication paths will also be made compatible with the existing underground telephone system to extend paging and voice communication throughout the underground mine. The new wireless equipment will include man-pack, vehicular, repeater, and base station transceivers. Repeaters and base stations will feature coupling networks for interfacing with the existing telephone circuits. Frequency modulation (FM) and single sideband (SSB) modulation processes are analyzed in view of the special conditions associated with underground mining. Of primary importance is the tremendous electrical noise generated in an operating mine that could adversely affect communications quality. High noise coupled with high attenuation rate of near field signals forces the communication system to be inherently short range. Fortunately, near field signals can propagate over great distances on underground wires and cables. The framework for comparison is generated by presenting all factors that

By Emmanuel N. Zevgolis

After the Krupp-Renn process was shown to be unsuitable for treatment of the Greek nickeliferous laterites, the LM process was developed. It involved roasting reduction up to metallic iron in a Rotary Kiln (R/K) and smelting in an Electric Furnace (E/F). Ferronickel (with 15% Ni) produced in the E/F, was upgraded to 90-95% Ni in an 02 converter. Raw Ni was then electrolyzed to pure Ni. The LM process was not applied for very long however, due to various problems. So, the Larco process was developed, i.e., pre-reduction in R/Ks, smelting of the calcine in E/Fs for ferronickel production (15% Ni) and enrichment to 20% Ni, in an O2 converter. Until now, many technological improvements have been invented and applied or adjusted to the process, which have made it a fully reliable and competitive one. sohe of the improvements were the invention and application of a new granulation process for liquid ferronickel, the modification of the existing R/Ks, E/Fs and converters and the design of new ones, and others that are described in the paper. Keywords: Ferronickel, metallurgy, laterites, LM process, Larco process

Jan 1, 2004

By D. A. Dahlstrom

THE necessity for slime elimination from valuable mineral and coal products has become increasingly significant within the past 5 years.1,2 Most of the mechanized mining and present beneficiation methods have resulted in larger tonnages of extreme fines, silts, and clay, commonly called slimes, processed by the preparation plant. Economics in turn have forced the plant operator constantly to lower the bottom size of effective beneficiation, necessitating an almost complete recovery of valuable solids regardless of particle size. When these important factors are considered, the need for an efficient slime removal method for fine solids becomes self-evident. Ordinarily slimes have been classified as ranging from 75 microns, or 200 mesh, down to colloidal dimensions of less than one micron. At the same time there is general agreement that the most troublesome slimes are primarily clays, silts and extreme fines, so that the actual top size may be placed at approximately 30 to 40 microns. This immediately restricts any desliming operation to classification, as screening or other methods would be both uneconomical and grossly inefficient at such dimensions. The liquid-solid cyclone has been recognized as one of the most efficient fine size classifiers available to the mining industry. Applications of cyclones to thickening, high efficiency solid recovery, degritting,

Jan 1, 1952

By M. Pourkani, M. Karga, Samid Banis, Andre Laplante, G. Langari-Zadeh

"The Sarcheshmeh mine processes 40,000 t/d of ore grading 0.9% Cu and 0.035% Mo. Grinding is effected in single stage ball mills using 80 mm forged steel balls, with an average consumption of 850 g/t. One of its 5 m diameter, 8 m length ball mills was emptied to measure the ball size distribution. The broken balls were first separated from the total charge, and the remaining balls classified into five size intervals of +7O mm, -70 +60 mm, -60+50 mm, -50+40 mm, -40 mm.The charge was composed of 280,534 balls (excluding broken balls) with a total mass of 305,180 kg. It was found that 4.0 % of the balls were broken; the size distribution of the charge was also markedly different from the desired one, in particular for the small-sized balls. For instance, 9% of the balls were expected to measure 2.54 to 3.18 cm in diameter, but none was found. On the other hand, the amount of top size balls was 30% higher than expected. The radial hardness of balls, which was determined by cutting the balls in halves, showed that the hardness sharply drops when the balls become smaller than 65 mm. The unexpected ball size distribution was attributed to the rapid change in the balls radial hardness. Based on the measured ball size distribution, a new ball make-up charge which uses 80% of 80 mm and 20% of 60 mm balls instead of 100% of 80 mm was proposed and implemented. The effect of the new ball make-up procedure in terms of ball consumption and grinding efficiency is being investigated."

Jan 1, 1999

By Glenn A. Squibb

An example of market development is described. The market in rail-lake movement of coal is vital to a rail carrier because of its location. This market is threatened by nuclear and other competing fuel sources and by depressed all-rail unit train rates, The first step to develop the rail-lake transportation market consists of rate adjustments and tariff changes to force tighter scheduling of mines, railroad, port and boats, and thus reduce cost. The second step provides a surge pile at the port to eliminate most of the seasonal disadvantage of rail-lake movement and reduce car detention at the port to almost zero.

Jan 1, 1966

New Zealand China Clays produces a unique halloysite clay product at Matauri Bay, Northland.   The company has licences over four deposits that were derived from the weathering of rhyodacite domes. Clay is mined and processed from two of the four deposits and is refined using a complex process based on gravity separation.   The product is almost entirely exported to niche markets in 24 countries. The main market is the fine ceramic industry where the product is used as a component in the manufacture of high quality porcelain and bone china bodies. The use of halloysite in these bodies gives the manufacturer the ability to achieve high whiteness and translucency. The other major market is for use in technical ceramics, where the product is sought after due to its high purity, fine particle size and stability at high temperatures.

Jan 1, 1997

By V. I. Ryaboy, V. P. Kretov, S. E. Levkovets, I. V. Ryaboy

"Using the flotation of a gold-containing ore from a deposit in Kazakhstan as an example, we have conducted a study designing dialkyldithiophosphate collectors, in addition to xanthates, for the flotation of hard-toenrich gold-containing ores to increase gold recovery.The increased flotational ability of the dialkyldithiophosphates was determined by their surface activity at the liquid-gas interface and their hydrophobic ability, the changing of which allowed us to control the collecting power and selective ability of the dialkyldithiophosphates. The studying of the surface activity of aqueous solutions was done using the stalagmometric method and the evaluation of the hydrophobic ability was done in percentage of the relative value of the zinc ion binding in the solution in standard conditions.Studying the influence of surface activity in our designed dialkyldithiophosphate collectors, with their close hydrophobic ability, showed that even with a small increase in surface activity in their aqueous solutions, gold recovery increased by 2-3% in laboratory conditions. Using this enabled us first to apply the dialkyldithiophosphate collector BTF-161 at a plant in Kazakhstan, and then to introduce the specially designed dialkyldithiophosphate collector BTF-163, which has been in use since. Further study of dialkyldithiophosphate activity based on this concept showed us that for the range of short-chain dialkyldithiophosphate collectors with a chain length of up to ?5, the effectiveness of ore processing became lower the higher their surface activity got, with relatively small differences in their hydrophobic ability. For long-chain dialkyldithiophosphates with a chain length of over ?5, ore processing effectiveness increased with the increase of their hydrophobic ability.Based on these studies, a new effective dialkyldithiophosphate collector, BTF-1517, was designed. Using this reagent in continuous gold recovery tests allowed us to reach an 84.21% recovery with a concentrate quality of 15.66 g/t, while using the applied collector BTF-163 in similar conditions led to the recovery of 82.87% with a concentrate quality of 15.65%. As a result, the Kazakhstan processing plant decided to conduct industrial tests with the BTF-1517 collector."

Jan 1, 2018

Electrical requirements in surface mining can be divided into three categories: main substation, plant power, and pit distribution. A main substation may vary from a 500-kva transformer supplying 480-v power to motor-driven pumps and conveyors, to a 50,000-kva substation serving a large beneficiation plant or a large strip mining operation. Regard- less of size, it should be designed with the realization that a failure of the main substation will totally shut down the operation. Location of a main substation usually is a compromise between expense of running the incoming high-voltage transmission lines and the voltage drop of long secondary runs. Based on a geological survey for immediate and future areas of excavation, the main substation should be located as near to the center of load as possible.

Jan 10, 1967

By Yuanbo Zhang, Yingming Chen, Zijian Su, Bingbing Liu, Guanghui Li, Tao Jiang

High calcium type tin, iron-bearing tailing is recognized as one of typically complex iron ore resources in China. A process of magnetizing roasting process followed by magnetic separation was used to utilize the tailings in our previous paper. Under the optimal conditions, qualified magnetic concentrates were obtained and could be used for direct reduced iron production. In this study, the phase transformation of these tailings during the magnetizing roasting process was investigated. And the reaction behavior between calcium oxide and iron oxide was revealed by using XRD, TG-DSC, VSM, etc. The results indicated that calcium ferrite was easily formed under CO–CO2 atmosphere, which has an unfavorable effect on the separation of iron and tin oxides from the tailings.

Mar 1, 2017

By A. A. Sizikov, V. A. Sizikova

Key parameters to consider for any producer: bring down production cost and lead time; Lean production as a tool to achieve maximum efficiency; How to implement lean principles: discontinuous vs. continuous production (aluminum industry); About RUSAL: global top-three aluminum producer; Lean tools at use at RUSAL's production facilities; Pull system, Standardization of work, Just in time, Continuous improvement, Customer-Supplier relations, etc.

Jan 1, 2006