Search Documents

By R. Cavanagh

Studies relating to the fixation of sulfur by reaction of 4 to 8 mm diameter cylinders of calcined limestone or dolomite with high strength sulfur dioxide in the temperature range 880°C to 1020°C were undertaken. Dolomites are far superior in sulfate capacity and reactivity than dense limestones even at high strength SO2. The sulfation reaction was first order with respect to SO2 concentration below 100 percent. Zero reaction rate at 100 percent SO2 concentration indicates that sulfate was the exclusive reaction product and that sulfite had no role in the reaction. At relatively low SO2 concentrations gaseous diffusion through the reaction product layer has a marked effect on the rate. As SO2 concentrations were increased up to 100 percent more complex rate controlling mechanisms unfold. By sectioning partially reacted dolomitic limestone pellets a moving interface was observed. Reaction ceased because of pore plugging for dense non-porous limestones at 30% conversion. With dolomitic material virtually complete sulfation of the calcium was observed. S.E.M. analysis showed that the average atom ratio Ca:S was 1.01, thus supporting the argument that little if any of the magnesium was sulfated.

Jan 1, 1996

By F. Hees, A. H. Bracken, L. I. Boshoff

"Biological cementation of the Mandena heavy mineral sand deposit in Madagascar was causing difficulty in dredge mining and hence in planning and control of production rates. An investigation was initiated to better evaluate the geotechnical properties of the orebody by defining the distribution and geotechnical properties of the cemented strata, in order to generate a site-specific geotechnical model for the deposit. The geotechnical characterization was developed by an integrated approach using several ground investigation techniques such as piezocone (CPTu) testing, geotechnical drilling, standard penetration testing (SPT), as well as laboratory testing. The final outcomes of the investigation included a 3D geotechnical model showing the distribution and extent of the cemented areas, as well as the typical geotechnical parameter ranges associated with each of the defined geotechnical units. The interpretations developed were incorporated into the mine and production planning to ultimately optimize operational planning and control.IntroductionQIT Madagascar Minerals (QMM) is a heavy mineral sand mining operation at Mandena, near Fort Dauphin in Madagascar. During the final planning and commissioning stages of the project, the need to fully characterize the unusual geotechnical conditions was identified and a geotechnical investigation became necessary.Nature of the problemDuring the commissioning phase it was found that mining production was being hampered by biologically cemented/indurated layers encountered within the sands. Closer inspection of the indurated horizons in the dredging face revealed that these layers contain a high loading of bacteria and fungi. It appears that the bacteria produce an extracellular (outside the cell) polysaccharide (i.e. sugar and carbon salts), which form a gelling biofilm to trap nutrients. There are a number of different bacteria. The fungi, on the other hand, produce a network of fibrous strands that bind the sand grains together. Thus both bacteria and fungi probably contribute to the ‘apparent cohesive’ strength or binding of the indurated sand (Lynn, 2008)."

Jan 1, 2017

By Richard H. Hopkins, R. W. Kraft

A new technique facilitating the rapid determination of the three-dimensional morphology of phases suspended in an opaque matrix is described. The vapidity of the technique is based upon continuous cinephotomicrographic recording of specimen microstructure as the specimen surface is removed under controlled conditions in an electrolytic cell. The advantages of the technique for determining spatial morphologies in opaque materials are illustrated by application of this method to the study of the configuration of faults in a specimen of directionally solidified CuAl2-Al eutectic alloy. A spatial model of the eutectic fault network deduced in this manner has substantiated the facts that faults in this alloy tend to lie parallel to one another in a direction close to that of the specimen growth axis and that the majority of faults tend to bridge lamellae rather than run parallel to them as growth proceeds. For the specimen studied fault density decreased as growth proceeded. ALTHOUGH metallographic observation is a powerful tool for investigating the correlation between structure and properties in metallic alloys, ordinary metallographic methods suffer the fundamental limitation that any conclusions concerning the three-dimensional structure of these opaque materials must rely upon inference from two-dimensional microsections. For this reason it is frequently impossible to make valid judgments regarding the true spatial distribution of the micro-constituents in specimens under investigation. Several techniques have been devised to circumvent the basic limitation of planar microsec-tioning and employed with varying success. These include construction of three-dimensional models of alloy microstructure from sequences of photomicrographs,1-3 quantitative deduction of spatial features based upon statistical studies of data from random and/or selected plane microsections,4-6 and selective dissolution of one phase in a two-phase alloy to reveal the topography of the phase remaining.' However these techniques also have certain obvious disadvantages. Construction of three-dimensional models is a very time-con- suming procedure due to the tedious polish-etch-photograph cycle needed to obtain the necessary photomicrographs to portray the spatial microstructure. Statistical methods by their very nature give only average values of the quantities being studied and cannot therefore give a detailed physical picture of the microstructure to be observed. Finally, the technique of selective dissolution is only applicable in systems where the phases are of vastly different chemical reactivity; it is of little use in the study of single-phase alloys. Since the determination of the three-dimensional structure of opaque materials is hindered by two facts—the materials are opaque to radiation in the visible spectrum and construction of spatial models of microstructure is quite laborious—two solutions to the problem suggest themselves: 1) use radiation of energy great enough to render the alloy transparent, i.e., some microradio-graphic method, or, 2) devise a rapid means to section and record alloy microstructure. Stereomicroradiography has indeed been used to study internal arrangements of phases in several materials8,9 but the method, in general, is limited to very thin specimens (due to X-ray absorption) and simple microstructures. It would seem then that development of a rapid, simple, and generally applicable technique for studying the details of alloy microstructures in three dimensions can best be undertaken by following the second approach above. Using this idea a new technique for rapid evaluation of spatial microstructures was developed based upon cinephotomicrographic recording of the micro-structure of a specimen undergoing controlled electrolytic dissolution. It was further felt that application of this technique to the careful study of the spatial configuration of faults in a CuAl2-Al eutectic alloy would yield information that could be correlated with the extensive data3,6,10-12 already compiled concerning the solidification and crystallography of this eutectic. The practicality and usefulness of similar methods for studying three-dimensional features in alloys has recently been illustrated by the study of dislocation loops in zinc13 and spheroidized structure in steel.14

Jan 1, 1965

By Nikkam Suresh

Dense medium cyclones have been in use for washing coarse and small coals for more than 50 years. There have been modifications in its design and today these units have become indispensable for washing of Indian coals possessing difficult washing characteristics. About 53 percent of the Indian coals (coking and non-coking) are being washed in jigs, about 38 per cent are washed in dense medium cyclones while the remaining 9 per cent is treated in other units like Barrel Washers, Heavy Media Baths and Drum Separators etc. The present paper deals with the attempts made for design of industrial Dense Medium Cyclones for enhanced coal recovery. Two industrial units of 500 mm diameter and 650 mm diameter were designed with their washing capacities being 200 m3/hr and 350 m3/hr, respectively. The results of the pilot tests conducted on 500 mm cyclone treating very high Near Gravity Material coals crushed to -3.0+0.5 mm gave an ash reduction of up to 19.5 percent with the new design i.e., from a feed ash of 34.5 percent to 15.06 percent in clean coal with an appreciable yield of 45 percent in one stage.

Sep 1, 2012

By Xiaolong Lin, Yuanbo Zhang, Jiann-Yang Hwang, Guanghui Li, Hongjin Zhang, Jiaxing Yan, Zhiwei Peng, Tao Jiang

The pollution caused by the spent printed circuit boards (PCBs) is currently a concern of researchers and environmental managers due to its large quantity and exceptionally complex properties. This study characterized printed circuit boards (PCBs) from discarded computers using a number of characterization techniques, including chemical analysis, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), granulometric analysis and scanning electron microscopy (SEM).The PCBs contain approximately 50 wt% metals, 25 wt% glass fibers and 25 wt% polymers. The principal metals include copper, calcium, tin, aluminum, zinc and lead. They are still wrapped by brominated epoxy resin after the PCBs are preliminarily crushed. As precious metals, such as gold and silver, are barely found in the PCBs, copper and tin are the main metallic elements of recycling value which warrants extra attention.

Mar 1, 2017

By Paul A. Rittenhouse

Its a pleasure to be with you this afternoon and to talk briefly on one of my favorite subjects -- the U.S. sulphur industry. As our Chairman mentioned, I have been associated with the sulphur industry either directly or indirectly for the last twenty years, both on the production side and as a consumer. Sulphur, while unseen and relatively unknown to most people, is like margarine ... that ubiquitous spread ... that is yellow and nearly omnipresent in the industrial world. It is because sulphur, in some form, is required in nearly all aspects of our economy that makes its study so interesting to me as a researcher. An analysis of the sulphur outlook requires examination of such industries as fertilizer, paints and pigments, copper and zinc, uranium, petroleum, chemicals, pulp and paper and textiles - just to name a few. Of course, because its use is so widespread and ever-changing it is difficult to develop and maintain a good understanding of the sulphur industry. It is also a problem to cover the industry in a short discussion and to project its really dynamic nature. Hut, if you will bear with me, I will attempt the task. First of all, let me say that sulphur today is a world commodity and to a large extent moves freely in world trade; nearly a third of the world's sulphur or something over 15 million tons in 1974 entered international trade. However, today our interest is in the current changing sulphur picture in the U.S., with particular emphasis on the western part of the country.

Jan 1, 1975

By Paul F. Kerr

QUARTZ of a certain kind, is one of our strategic minerals, and Brazil is probably the one important available source. Crystals of quartz of suitable size and perfection for piezoelectrical application are rare; their most outstanding use is in radio work. Clear quartz, or "crystal," free from twinning, cracks, foreign particles of other disturbing lines of growth, and gaseous or liquid inclusions, is cut into plates which provide excellent control of frequency in broadcasting. The squares or rectangles are less than a millimeter in thickness and ordinarily on the order of 1 in. along each side. They are cut at definite angles with respect to the axes of the crystal, and ground with opposite surfaces parallel. Each small slab must be a section of one crystal, uniform throughout in atomic alignment. The thickness of the chip controls the frequency of a broadcast and it is most important to have the plates oriented and ground with utmost precision. Opposite surfaces are parallel to within 0.001 mm. and expansion or contraction due to the temperature is limited to one part in a million.

Jan 1, 1942

For the first time in its history, the George A. Fox Conference let its focus venture away from the friendly confines of the East Coast of the United States to spend part of the one-day conference looking at projects from around the globe. With a record-setting attendance of 377 people, the conference, titled ?Tunneling: An international perspective,? opened with a keynote speech from special guest In-Mo Lee, professor, Korea University in Seoul, South Korea. He is also the president of the ITA-AITES. In a sweeping presentation, Lee walked the packed audience through some of the most fascinating and challenging projects in his home country. Among the projects he spoke about were Korea?s longest railway tunnel, the Solahn Tunnel and the Inje Tunnel, a freeway tunnel that is 11.94 km (7.4 miles) long.

Jan 1, 2012

By S. K. Mishra, S. B. Kanungo, D. Biswal

An attempt was made to beneficiate low-grade, high-phosphorus manganese ores of the Garividi-Garbham region of Andhra Pradesh, India, by using wet high-intensity magnetic separation (WHIMS). The distribution behavior of both mass and chemical constituents in different size fractions of a typical highly weathered ore sample was studied to obtain information about the liberation characteristics of various chemical constituents. Magnetic separation indicated that in the +208-µm size fractions, P and acid insolubles were concentrated in the magnetic fractions. However, in the -208-µm size fractions, P and acid insolubles were concentrated in the nonmagnetic fraction because of a lower recovery of the magnetic fraction. Variations in field intensity between 1.3 and 1.75 T had little effect on the recovery and the grade of concentrate. The results also demonstrated that phosphorus was associated with all three major constituent phases, namely, oxides of Mn and Fe and aluminosilicate gangue minerals.

Jan 1, 2000

By R. J. Folic

Investigations of the vibrations of a pile in soil are performed on a dynamic model in the form of a prismatic bar of finite axial and flexural stifnesses with a discrete mass at its free end representing the cap. The soil is represented by a system of springs of constant and variable stiffnesses. Oscillation differential equations are derived by means of the Hamiltonian principle for non-conservative systems. The problem is reduced to a coupled system of two non-linear partial differential equations with corresponding initial-boundary conditions. Frequency equations of longitudinal and lateral linearized equations are formed. The paper determines natural frequenc­ies and oscillation modes. It separately examines longitudinal vibrations excitated by a hermonic force acting upon the pile cap, and lateral vibrations excitated by an impulse acting upon the cap. The results of the numerical processing are presented in respective diagrams in dimensionless form.

Jan 1, 2010

By R. Duncan Gardner

This paper describing the mining practice at the Harmony mine, Baker, daho, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. About 150 tons of copper ore containing 4 per cent copper, 0.001 ounce gold, and 0.1 ounce silver, is being produced daily from the Harmony mine by the shrinkage method of mining. The ore is taken by an aerial tramway 1/3 mile long to the mill, where it is concentrated. The concentrate is shipped 8 miles by truck to the railroad and thence by rail to Utah for smelting.

Jan 1, 1930

By S Smit, P J. J Strobo

ZINIFEX Century Mine is a zinc, lead and silver concentrate producer. Flotation is the primary method of minerals separation in this circuit. The flotation circuit is quite large with 79 flotation cells. The levels in each of these interconnected cells are controlled at more than 45 level control stations. Due to the multivariable interaction throughout the circuit, good level control was found to be difficult to achieve by just using normal Proportional-Integral-Derivative (PID) control. As a first step in advanced process control, the FloatStar Level Stabiliser, a multivariable controller developed specifically for flotation circuits, has been commissioned at Century mine to solve the level control problems. The first section of this paper therefore discusses and shows the results and improvements obtained by using the FloatStar level stabiliser. The results and benefits of the FloatStar Flow Optimiser are discussed in the second section of this paper.

Jan 1, 2004

By V. M. Karve, K. K. Majundar, K. V. Viswanathan, J. Y. Somnay

The effect of calcium, magnesium, iron (both ferrous and ferric) and aluminum ions, which are commonly encountered in a typical beryl ore, was studied in the flotation of pure beryl, soda-feldspar and quartz. The vacuumatic flotation technique was employed. With sodium oleate as collector and in the absence of any activator, beryl floated in a pH range of 3 to 7.5, whereas feldspar and quartz did not float at any pH up to 11.5. The pH range of flotation increased in the presence of the ions studied. With calcium and magnesium ions beryl floated from 3 to 11.5 pH and beyond, soda-feldspar floated beyond pH 6 and quartz floated beyond pH 8. Ferrous ion activation was found to be similar to that of calcium and magnesium. Activation by ferric and aluminium ions was found to be complex and the lower and upper critical pH for all the three minerals was around 2 and 10 respectively. These studies indicated the possibility of separation of beryl from feldspar and quartz even in the presence of calcium, magnesium and ferrous ions between pH 4 and 6. Flotation tests on a mixed feed of pure minerals in a 10 g cell revealed that beryl can be selectively floated from feldspar and quartz if ferric ion is reduced to ferrous state or if it is complexed. Beryl occurs mostly in pegmatites, and hence is associated with feldspar, quartz and micas and small amounts of other minerals such as apatite and tourmaline. The separation of beryl from these minerals is difficult because all the silicates accompanying beryl have more or less the same physical properties. Specific gravities of beryl, feldspar and quartz are 2.70, 2.56 and 2.66 respectively. Electrostatic separation has been suggested but no work has been reported. ' The adsorption of sodium tri-decylate tagged with Cl4 on beryl, feldspar and quartz reveal similarity in surface properties. Much work has been reported on the flotation of beryl from ores, either directly or indirectly as a by-product, but little is known about the fundamental aspects of beryl flotation. Kennedy and O'Meara3 laid emphasis on prior cleaning of the mineral surfaces with HF. Mica is removed first by flotation of beryl with oleic acid, around neutral pH. Runke4 introduced calcium hypochlorite conditioning in a final separation stage for activating beryl in a mixed beryl-feldspar concentrate, and after washing to remove the hypochlorite, floated beryl with petroleum sulphonate. The Snedden and Gibbs5 procedure is somewhat similar to that of Kennedy and O'Meara. Emulsified oleic acid is used as collector. Recently Fuerstenau and Bhappu6 studied the flotation of beryl, feldspar and quartz with petroleum sulfonate in the presence of activators and stressed the importance of iron in the flotation of beryl. From the studies conducted in this laboratory, it was found that feldspar and quartz as such do not float with sodium oleate, but in practice selective flotation of beryl from feldspar and quartz in an ore is found to be impossible with sodium oleate as collector. A glance at the chemical analysis of typical beryl ore indicates the presence of several ions like Ca ++, Mg++, Al + + + and Fe+++ in abundance and Ti++++ and Mn++ in traces. Hence, in an attempt to explain the behaviour of feldspar in the beryl flotation, the effect of Ca++, Mg++, Al+++ and Fe+++, which are known as gangue mineral activators7'8 has been investigated. Materials and Methods: Lumps of beryl ore (hand picked) were boiled with 10% sodium hydroxide and washed with distilled water. They were further boiled many times with 10% hydrochloric acid till no positive test for iron was obtained with ammonium thio cyanate. This was followed by thorough flushing with double distilled water. The lumps were crushed in a porcelain mortar and pestle under water. The minus 65 + 100 mesh fraction was used for testing and was always stored under distilled water. Pure feldspar and quartz were similarly prepared and the minus 65 + 100 mesh fractions collected. Inorganic ions tried as activators were ca++, Mg++ , Fe++, Fe ++ and A1 +++ . Calcium nitrate, magnesium chloride, ferrous ammonium sulfate, ferric ammonium sulfate and aluminum nitrate of G.R.E. Merck grade were used. B.D.H. technical grade sodium oleate was used as a collector. The vacuumatic flotation technique developed by Schuhmann and Prakash was used for studying the effect of pH on flotability. 7 The indications given by this work were confirmed by using 10 g miniature cell.'

Jan 1, 1965

By G. Taylor

A 21st Century worker is one who works less with his physical power and more with mental ability. Such a worker is more skilled than a labourer and is consequently rewarded accordingly. A21st Century supervisor is one who ensures that workers are constantly supported so that they can maximize safety and productivity. A 21st Century manager is one who constantly searches for ways to maximize returns for the various stakeholders. Given the well-known constraints in narrow reef mining, all of the above is meaningless unless a mining method is found which provides conditions which support the 21st Century initiatives. [ ] The identified mining method is a continuous non-explosive stope breaking system using rocksplitter technology. Rocksplitting is defined as: The fragmentation of rock through high energy pulse wave transmission in a fluid-filled hole or hydro fracturing. Shotholes are effectively filled with a water-based geland 30 grams of explosive after which the hole is closed off with a ?rocksplitting gun?.

Jan 1, 2000

By Sam S. Taylor, H. M. Smith

"INTRODUCTION In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas Produced with the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production must be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a gas supply is not available, often air is used.Although P.ir is a Cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, some fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case. The Petroleum Experiment Station of the United States Bureau of Mines at Bartlesville, Okla., has been interested in problems connected with air-repressuring for a number of years. Some time was spent in studying the so-called ""bad gas""--return,mixture of low fuel value. However, it appeared impossible to attack the problem successfully from this angle, and an approach was made through a laboratory--scale study of direct oxidation of crude oil."

May 1, 1934

By H. Möller, M. Tshibalanganda, C. Taute, A. du Plessis, M. Leary

Additive manufacturing can be used to produce complex and custom geometries, consolidating different parts into one, which in turn reduces the required number of assemblies and allows distributed manufacturing with short lead times. Defects, such as porosity and surface roughness, associated with parts manufactured by laser powder bed fusion, can severely limit industrial application. The effect these defects have on corrosion and hence long-term structural integrity must also be taken into consideration. The aim of this paper is to report on the characterization of porosity in samples produced by laser powder bed fusion, with the differences in porosity induced by changes in the process parameters. The alloy used in this investigation is AlSi10Mg, which is widely used in the aerospace and automotive industries. The sample characteristics, obtained by X-ray tomography, are reported. The design and production of additively manufactured parts can be improved when these defects are better understood.

Apr 1, 2021

By Charles G. Zink

Anthracite is widely known as a domestic or space heating fuel. The prevailing market ratio of domestic to industrial consumption was about 80 to 20 up until 1950. Since then it has been shifting until now the ratio index is about 50/50, exclusive of overseas export. Despite a declining domestic space heating market, the demand for industrial anthracite remains good. However, as a result of stringent air pollution regulations, there is a renewed interest in this low sulphur coal which cannot smoke under any conditions. Anthracite serves other important industries such as power generating, metallurgical, cement, ceramic, chemical, water sewage and industrial wastes filtration. Anthracite is an excellent natural source of carbon and may be utilized in many processes.

Jan 1, 1966

By S. F. LEAMING

Jade occurs with alpine-1ype serpe111iniIes in a be// of middle Paleozoic to Triassic rocks extending from southern British Columbia in10 Yukon Territory. Most known deposiIs are in BriIish Columbia and are associa1ed wi1h the Cache Creek Group. Jade deposits are generally small len1icular masses 1ha1 lie along con1acIs beIween serpenIinites and various countIy rocks; some are 1ec1onic inclusions wi1hin se1pen1ini1es. Qualify and quan1i1y of 1he jade varies widely. Deposi1s occasionally, but rarely, reach 3,000 /Onnes. The ma1erial may be rendered non-commercial by .frac1ures, impuriIies, inferior colour and poor IexIure. Because unit value of jade can approach $80.00 per kg, greaI incen1ive exisIs 10 exploi1 1his resource. Successful commercial operations, however, depend on large- *A more detailed version of 1hi paper occur in Leaming (1978). PHOTO I . Sawn blocks of nephrite ready for shipping. 270 volume sales, for which $6.00 to $15.00 per kg is more realistic. Many undiscovered jade deposits undoubtedly remain in the Canadian Cordillera.

Jan 1, 1984

By Nathan C. Rockwood

The title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. Definition of Mineral Aggregates " Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without port-land cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. provide aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theeretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. Exploration and Possibilities of Development The distribution of deposits of mineral aggregate is universal, since almost any part of the earth,s crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (i) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engilleering talent in its operating branch, but it lacks, to a considerable degree, engineering talent with experience

Jan 1, 1948

By Nathan C. Rockwood

The title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. Definition of Mineral Aggregates " Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without port-land cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. provide aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theeretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. Exploration and Possibilities of Development The distribution of deposits of mineral aggregate is universal, since almost any part of the earth,s crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (i) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engilleering talent in its operating branch, but it lacks, to a considerable degree, engineering talent with experience

Jan 1, 1948