Search Documents

By Wiechers HNS

In China the hydrogeological type of solid mineral deposits can be divided into A. Mineral deposits with fissure water; B. Mineral deposits with pore water; and C. Mineral deposits with karst water. The hydrogeological conditions of mineral deposits with fissure water are relatively simple with the exception of a few cases. Mineral deposits with pore water are few but great amounts of ground water can be encountered in the mine accompanied by floating sand or slope failure during the exploitation. Mineral deposits with karst water are complex in their hydrogeological conditions. Enormous inrushes occur frequently in the mines of north China; Karst collapses are a serious matter in the mines of the south; Subterranean river and conduit systems are often encountered in the southwest. This paper will give full discussion on these features and put forward a way of combating and controlling the groundwater problem in accordance with type and feature.

Jan 1, 1988

By Boontanjai C, Boyapati ER

Reagents used for batch flotation tests were Aeroxanthate-343 & 350, Dow Z-6, & reagent-4037 (from Benambra) as copper collectors; Na2SiO3 & Na2S2O3as gangue depressants; lime & HCl as pH regulators; and pine oil & MIBC (methyl isobutyl carbinol) as flotation frothers. A Denver Sub A flotation cell of capacity 250 gms was used for the batch flotation experiments. Atomic absorption spectrophotometer was used for copper assays and microscopy for selectivity and liberation studies. Melbourne tap water was used throughout the experiments. Unless otherwise stated, the following parameters apply to the flotation experiments: flotation impeller speed - 1300 rpm, pulp density during flotation- 22%, reagents addition - in 4 stages, total conditioning time for collectors - 8 minutes, total flotation time- 9 minutes. A variable quantity of copper mineral collector according to the test in question was added, then conditioned the pulp for 2 minutes. The froth was removed by hand, scraping the full length of the cell at constant depth every 10 seconds. No frother is required for this copper tailing flotation. Four concentrates were collected after addition of collector and conditioning at 2,4,6 and 9 minutes. The pulp volume was maintained at a constant level to yield a constant froth depth.

Jan 1, 1990

By Mark Flower

A 20L ignition test chamber has been used to test suspensions of 7 UK and world traded coals in air and O2/CO2 mixtures typical of oxy-combustion conditions. The coals varied in rank from sub-bituminous to bituminous and were tested in varying concentrations from the ignition limit to 400g/m3. Following each successful test the combustion residue was collected, weighed and analysed within a thermogravimetric analyser, allowing Q factors to be estimated. The ignition limit varied slightly in air, but was mostly around the 200g/m3 level. With the exception of Coal C, which was much harder to ignite, it correlated roughly with coal rank. The ignition limit changed significantly with O2 concentration when in mixed O2/CO2 gases. Only a few high volatile coals ignited in 21% O2/CO2 v/v, and then only with a 2500 J, rather than a 1000J, igniter. An increase in O2/CO2 levels to 30 or 35% gave ignition patterns similar to those carried out in air with a further increase to 40% having little additional effect. In addition the minimum ignition concentration decreased with increase in O2. Heterogeneous combustion or gasification of the coal by CO2 appears to be confirmed by comparing weight loss results for air and O2/CO2 mixtures respectively for an equivalent peak pressure rise.

Jan 1, 2009

By Warren D. Longwill

The Bureau of Mines inventoried Federal lands in the State of Oregon and classified them in detail, section by section, according to their availability for mineral exploration and development as affected by legal status and agency management practices. The Bureau determined areas of the State having past mineral production and/or known metallic mineral resources and areas favorable for coal, oil, gas, and geothermal resources, and prepared maps that spatially compare the availability of Federal mineral land with these mineral areas to demonstrate the extent of restrictions to mineral entry. Oregon contains 62.1 million acres, of which 33.9 million acres or 55% is Federal mineral land. About 2.3 million acres of Federal land is favorable for selected metallic mineral deposits, of which 64% is available, 13% is restricted, and 23% is unavailable. Of the 21.1 million acres of Federal leasable land favorable for oil and gas, 68% is available, 11 % is restricted, and 21 % is unavailable. Of the 146,720 acres favorable for coal, approximately 71% is available, 13% is restricted, and 16% is unavailable. Federal leasable land favorable for geothermal resources amounts to 458,968 acres, of which 42% is available, 34% is restricted, and 24% is unavailable.

Jan 1, 1988

By John K. Gustafson

The title of my talk is "The Gold Miner and the Future of Gold." This title might just as accurately have been stated as "Gold and the Future of the Gold Miner." Since prehistoric times gold has been sought by mankind for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value and lubricated trade between peoples. For at least 6000 years, gold has been used to barter for other commodities. It has been prospected for, treasured, made into works of art and personal adornment, and from time to time has been the object of conquest. Because of its predominant role in recent centuries as a basis for money, economists began to think of it solely in these terms. Annoyed by the disciplinary pressure of gold on the money manager's desire to manipulate money, the famous economist, John Maynard Keynes, characterized it as a "barbaric relic of the past", a characterization repeated by William McChesney Martin, Jr., when he was head of the Federal Reserve Bank. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world.' It is the most ductile metal known. An ounce of gold, for example, can be drawn into a continuous wire over 35 miles long. It also is so malleable that an ounce of gold can be beaten into films ten one-millionths of an inch thick sufficient to cover 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of gold weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity, only slightly less than silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity both to light and infrared rays. Because of these qualities, in addition to its rare beauty, industrial and artistic uses of gold have been growing rapidly. On a world basis, a recent study estimated that in 1960 about 750 tons of gold were used for fabrication, and that the amount had grown to about 1296 tons in 1968. My objective in this talk is to discuss with you the present and future supply of and demand for gold on a worldwide basis and the effect these forces are likely to have on the price the miner can expect to receive for the gold he produces. This is a highly controversial and risky subject to discuss before any audience. Nevertheless, it is a subject that I live with constantly as Chairman of the

Jan 1, 1972

By W. K. Tolley

The Bureau of Mines is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from CdTe scrap produced in the manufacture of infrared optic devices. Sulfation, ferric chloride leaching, and oxygen-pressure leaching have been tested. Cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. However, no satisfactory scheme for dissolution of the higher valued tellurium has been devised. Leaching the ground CdTe for 75 min at 110°C in 1.1M H2S0, under 120 psig 0, yielded 99.5% Cd extraction. Tellurium remained in the leach residue as TeO, and elemental tellurium; residual cadmium was less than 0.5%. The cadmium in the leach liquor was purified of coextracted metals such as gallium and iron by adjusting the pH. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Recovery of by product metals, notably gallium, is possible.

Jan 1, 1991

By S Johnston, L Howe, S Stevens

Regulators have an important role to play in fostering and enabling reliable, effective, environmental management. Given this, it is perhaps surprising that there has been relatively little debate on exactly how regulators can enhance their own approaches, in order to promote improved outcomes overall. The authors argue that applying research on High Reliability Organisations, as well as the University of Pennsylvania’s Penn Program Framework for Regulatory Excellence, to regulators has the potential to facilitate positive environmental results across the mine life cycle.

Aug 2, 2023

By J. J. Shields

This is the Seventh of a series of publications that describe methods and practices used in mining bituminous coal mechanically.3/ This report deals with the operation referred to in coal mining as continuous mining, and the interest shown by mining companies in this method is the reason for this study. Only continuous mining as it applies to the room-and-pillar system of mining, or a modification thereon, is discussed in detail in this report. Although not always as continuous as the name implies, it is a system of mining in which a machine is used to cut and load coal in one continuous operation without drilling and blasting the coal. With the mining equipment in most general use today, the usual cycle of operation in mining of coal is: (1) Timber, (2) cut, (3) drill, (4) blast, and (5) load. As the phases of this type cycle cannot be performed simultaneously in the same working place, it is necessary to operate from 3 to 7 working places so that at least 1 place is available for coal loading at all times. Even if the schedule of the phases in a cycle is maintained, coal production ceases during the time required to move the loading equipment from one loading place to the next. In 1920 a continuous-type mining machine4/ was installed in an Illinois coal mine to drive entries. Several other companies used these entry drivers for short periods in the following few years. In 1927 a southern Illinois coal company installed 2 of these machines which, in the next 25 years, were reported to have driven over 200 miles of entries. The machines did not attain widespread usage.

Jan 1, 1954

By Kurt Wiener

A major process control system is in some ways like a complex organism. The extremities, (that is, field instruments) are exposed to many hazards and suffer malfunctions of relatively minor and repetitive nature. Here I equate a stuck valve or dead transmitter with a skin abrasion or cut. The maintenance and repair of the extremities can be done by technicians with basic but thorough knowledge of relatively few problems and their solutions. Here I equate with administering Band-Aids and aspirin. On the other extreme, when the master control device (such as a computer) fails, one does not attempt home remedies. A "brain" specialist is called in. It is, however, crucial that the patient be able to clearly describe his symptoms. Getting down to the case at hand, a complex system consisting of field instruments, instrument racks, interface equipment, and perhaps a computer, may require maintenance at all levels. At the field equipment end where physical damage, corrosive atmospheres, reconfiguration, and routine calibration checks are common, the customer has the opportunity to develop a competent staff of maintenance people. The relatively high maintenance activity assures competence through repetition.

Jan 1, 1980

By W. L. Phillips

Single crystals of aluminum, brass, and copper oriented for (100) and (110) slip were extended at 25°, 400°, and 600°C in simple shear. Aluminum specimens oriented for nonoctahedral slip began to shear at a higher critical resolved shear stress than specimens oriented for octahedral slip. Parabolic stress-strain curves were obtained from zero strain. The initial rate of parabolic hardening was lower for specimens sheared on the (100) plane in a close-packed direction <110>, than for specimens sheared in a nonclose-packed direction <100>. metallographic evidence, however, showed that all slip traces could be explained in terms of (111) <100> slip. All attempts to cause nonoctahedral slip in copper and 70-30 a-brass single crystals were unsuccessful. Instead of shearing, the crystals bent, allowing {111} type planes to come into action. NONOCTAHEDRAL slip in aluminum has been reported under three different conditions: first, as the main mode of slip in tension experiments at elevated temperatures;&apos;-&apos; second, as the main mode of slip in direct shear experiments at room temperat~re; and third, as a minor mode of deformation, i.e., as cross-slip, in tension, shear, and bicrystal experiments at room and elevated temperatures."-l2 However, as far as the author knows, nonoctahedral slip has not been reported in either copper or 70-30 a-brass. The present study was undertaken to determine whether nonoctahedral slip could be obtained in aluminum, brass, or copper at room or elevated temperatures when the shear stress was approximately constant over the cross-section, a maximum at the center, or a maximum at the surface. EXPERIMENTAL PROCEDURE A detailed description of the crystal preparation and shearing apparatus has been given previo~sly. Cylindrical crystals 1/2 in. in diam and 8 in. long were grown from the melt in a temperature-gradient furnace. The aluminum contained 0.001 pct Zn, 0.001 pct S, and 0.001 pct Fe; the 70-30 brass contained 0.015 pct Pb, 0.001 pct Fe, 0.01 pct Ni, 0.02 pct Sn, and 0.005 pct Se; the copper was certified OFHC of 99.98 pct purity. All samples were electropolished prior to testing. The shear apparatus was a modified Bausch type. The strain sensitivity was 4 x lob4 Load was applied by clamping the rods attached to the shear plates in an Instron tensile machine. The rate of loading was 0.02 in. per min. In all cases a 1/8-in. gage length was used. For the tests performed at 400° and 600°C the shear plates, collars, and rods were made of stainless steel. These elevated-temperature tests were performed in an argon atmosphere. A) Aluminum at Room Temperature. Values of a and ß for the various slip planes and slip directions investigated are shown in Table I where a is the complement of the angle between the specimen axis and the slip direction, and ß is the angle between the specimen axis and the normal to the shear plane. The shear stress is a function of a (assuming ß - 0);10 when a is less than 27 deg, the shear stress on the slip plane for which the specimen is oriented has a maximum at the center of the crystal; at a = 27 deg the shear stress is constant across the slip plane; for a greater than 27 deg the shear stress is a minimum at the center. Fig. 1 shows the stress-strain curves for specimens cut from crystals 1, 2, and 5, which were sheared on the (010) plane in the [loll direction at room temperature. These three crystals have shear-stress distributions corresponding to the three dif-

Jan 1, 1962

By E. J. Roberts

F. C. Bond (Allis-Chalmers Mfg. Corp., Milwaukee) —This paper considers comminution as a first order process, with the reduction rate depending directly upon the amount of oversize material present. The data show that other factors should be taken into account, and it is possible that in time these may be evaluated as simultaneous or consecutive reactions: Development of the theory of comminution has been retarded for many years by the assumption that surface area measurements constitute the sine qua non of the work done in crushing and grinding, and it is encouraging to note the belated growth of other ideas. In the Abstract the term "net power" should be changed to "net energy." Throughout the paper the term "hp per ton" should be changed to "hp hrs per ton", or "hp hr t." The term "Probability Theory" in the title does not seem appropriate, since it is not clear how the probability theory is used in developing the ideas in the paper. There seems to be a contradiction between the large calculated advantages of closed circuit operation and the statement following that the closed circuit test results showed no significant change in grinding behavior, when compared with the batch grind curves. Tables I and II show that between 75 pct and 50 pct solids the energy input required decreases with increasing moisture content and may indicate the advisability of grinding at higher dilutions in certain cases. The calculation of the hp-hr per ton factor indicates an input in the laboratory mill of only 7.32 gross hp per ton of balls; this casts some doubt upon the accuracy of the factor used, since the power input in commercial mills at 80 pct critical speed is customarily much higher. The tests show that within fairly wide limits the amount of ore in the laboratory mill may be varied and a product of constant fineness obtained, provided that the grinding time is varied in the same proportion. This has often been assumed, and confirmation by actual testing is of value. The Cavg corrections for differences between the plant and laboratory size distributions do not seem very satisfactory, since in many cases the plant/laboratory ratio is farther from unity after correction than before. The following equation has been derived from the data in Table VI: Relative Energy (log new ball diam in in. + 0.410) Input = --------------—--------------- from which the relative energy inputs for balls of different sizes can be calculated and compared. The relative energy input is unity for balls of 2.715 in. diam. The equation indicates that the work accomplished by a ton of grinding balls per unit of energy input is roughly proportional to the square root of the total ball surface area; provided, of course, that the balls are sufficiently large to break the material. The data in support of this statement are admittedly meager, but are fairly consistent when plotted. The relative grindability values listed in Table VI for 200 mesh multiplied by 4/5 apparently correspond approximately to the A-C grindability at 200 mesh.&apos; It would seem that for open circuit tests comparable accuracy could be obtained much more simply by the old method&apos; of plotting the test grind, extending the mesh grinds to the left of zero time if necessary, and determining from the plot the equivalent time required to grind from the plant feed size to the plant product size, using the average of several mesh sizes. The en- ergy input value of one time interval could be determined by tests on materials of known grinding resistance, and this multiplied by the interval required should give the desired energy input value. The relative grindabilities would be the relative time intervals required for a specified feed and product size. When the plotted mesh size lines of a homogeneous material are extended to the left beyond zero time they meet at one point at zero pct passing. The horizontal distance of this point from zero time indicates the equivalent energy input required to prepare the mill feed. The author&apos;s results show that the closed circuit grinding tests give about the same K values as open circuit tests, from which he concludes that open circuit tests are satisfactory in many cases. The value of the closed circuit test is its ability accurately to predict energy requirements in closed circuit grinding for both homogeneous and heterogeneous materials. If the material is homogeneous, the open circuit test gives satisfactory results; but if the material contains appreciable fractions of hard and soft grinding ore, the open circuit tests will not be accurate because of the accumulation of hard grinding material in the circulating load. Since in most cases it is not possible to determine a priori whether the material contains hard and soft fractions, the closed circuit tests are preferable and more reliable. B. S. Crocker (Lake Shore Mines, Ontario)—Dr. Roberts probability theory of grinding is very similar to our log pct reduced vs. log tonnage method of plotting and evaluating grinding tests at Lake Shore. However, although we both seem to start at the same point we finish with different end results. Shortly after publishing our grinding paper (referred to by Dr. Roberts) in 1939, we did pursue the subject of the "constant pct reduction in the pct +28 micron material for each constant interval of time. We ran innumerable tonnage tests on the plant ball mills, rod mills, tube mills with 11/4 and 3/4 balls, and lastly pebble mills, with tonnage variations from 180 tons per day to 950 tons per day. We found that when we plotted the log of the tonnage against the log of the pct reduced of any reliable mesh, we had a straight line up until 90 pct of the mesh is reduced. We have also tested this in our 12-in. laboratory mill with the same results. We have used this method of evaluating grinds for the past 8 years and developed the recent four stage pebble plant on this basis. By pct reduced we mean the percentage of any given mesh that is reduced in one pass through a mill at a given tonnage (or time). For example, if the feed to a rod mill is 90 pct +35 mesh and the discharge at 500 tons per day is 54 pct +35, the pct reduced is 90 — 54/90 = 40 pct. If the feed had been 80 pct +35 the discharge would have been 48 pct +35 or pct re- duced 80-48/80 = 40 pct as long as the tonnage re- mained constant at 500 tons per day. Thus we can easily correct for normal variation of mill feeds. This log — log relationship derived from the tonnage tests of all our operating mills has proved of tremendous help in checking laboratory work and in designing alternate layouts or new plants. The difference between the log — log and the semi-log plot is only shown up when the extremes in tonnages are plotted. When the relationship between the pct reduced and the tonnage was first investigated, we used semilog

Jan 1, 1952

By Albert Sauveur

It is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.&apos; The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson&apos;s paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance. Physical Properties of Cast-Iron us. Its Ultimate Composition. Mr. Johnson writes that " an investigation along the lines of consumption showed that different irons have different characters totally independent of their analyses," and he declares that " the presence or absence of these elements [meaning carbon, phosphorus, silicon, and manganese] alone will not account for all, scarcely for a half, of the facts which have long been known." He further tells us that some foundries have " proved, by the most irrefutable tests, that they could take a certain iron of a given analysis and produce certain results," while with " another iron of the same analysis they could not produce these results at all." I feel confident that every experienced and thinking metallurgist will readily believe Mr. Johnson&apos;s statements and will share his views in regard to the hopelessness of inferring the

Jan 1, 1914

By Bingguo Liu, PENG LIU, Haigang Dong, Jinhui Peng, Libo Zhang

Parameters of technique to decarburize from spent petrochemical catalysts via microwave oxidation roasting were investigated. Decarburization process was performed on a microwave heating system. The results showed that the decarburization percentage of spent petrochemical catalysts was significantly affected by roasting temperature and sample thickness in the range studied. The decarburization percentage was 99.5% in microwave fields under the optimized conditions, roasting temperature 600 °C, roasting time 40 min and sample thickness 2 cm respectively. The residuum after microwave decarburization was characterized by field emission scanning electron microscopy (FE-SEM) which showed that the deposit carbon had been removed effectively.

Mar 1, 2017

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um

New modern water treatment technologies required for arsenic removal from waste waters contaminated extensively by various background sources from mining, industrial waste, agricultural waste, painting industry and natural geological bed rock system etc. Arsenic is a widely dispersed element in the earth&apos;s crust and exists at an average concentration of approximately 5 mg/kg. Arsenic (As) and heavy metals may be released from the mine wastes to the ground and surface water systems, as well as the geological environment due to their solubility and mobility. This research focuses on the effect of accelerated carbonation process for successful removal of heavy metal arsenic anions from artificial waste water and mining waste waters. This accelerated carbonation process is a simple and novel method with 85 ~ 88% removal efficiency. Carbonation has been studied as a process to further improve immobilization of solidified/stabilized waste and granular waste. After successful removal of arsenic anions from solid mining waste and its potential benefits for producing construction materials. Besides, the industrial and urban management systems are generating bulk solid mining wastes, and most often dumping them in open fields. To prevent the landfilling with mining waste, many efforts are being made for the recycling of different types of mining solid wastes with a view to utilizing them in the production of various construction materials.

Jan 1, 2014

By A. Sokolov, M. Demsky, E. Hasikova, V. Gostilo

"Previously, we upgraded and implemented two gamma activation assay (GAA) systems designed to analyse the gold content in raw ores at Zarafshan laboratory, Uzbekistan, and achieved a detection limit of less than 0.05 g/t under actual industrial conditions. Having started to design a fully modern, industrial GAA system for mining companies, this paper analyses the advantages, disadvantages, and special features of all major system components that can influence the sensitivity and accuracy of the analysis. The results of a study to optimize the detector geometry and sample size are presented and the performances of the linear electron accelerator, detector array, and sample transportation system of a modern, industrial GAA system for analysing gold, silver, and rare earth elements are considered. IntroductionGamma activation analysis (GAA) has considerable potential as a future replacement for traditional fire assay analysis in gold mining (Hoffman, Clark, and Yeager, 1998; Morse, 1977; Bourmistenko, 1986, 1981; Sammut, 2016; Tickner et al., 2017). The essence of GAA is to irradiate ore samples with high-energy gamma quanta generated by an electron linear accelerator (LINAC) and then to use a gamma spectrometer to detect the induced activity of the excited gold nuclei. The advantages of this method are discussed in detail elsewhere (Hoffman, Clark, and Yeager, 1998; Morse, 1977; Bourmistenko, 1986, 1981; Sammut, 2016; Tickner et al., 2017), where it is shown that GAA is uniquely suited to analysing ore samples when mining for gold, other precious metals, and accompanying elements.These advantages were realized in three industrial GAA laboratories that were commissioned in Zarafshan, Uzbekistan in 1977, in Magadan, Russia in 1979, and in Batagay, Russia in 1986 (Bourmistenko, 1986; Nii Tekhnicheskoy Fiziki I Avtomatiki, n.d). In 1989, a fourth industrial GAA laboratory was commissioned at a gold mine in Tommot, Russia. However, the project was subsequently halted due to economic reasons (Moshkov and Tjamisov, 2017). Currently, only the laboratory of the Muruntau mine in Zarafshan, Uzbekistan is in operation. The gamma activation method for gold determination is widely applicable at this mine owing to its high productivity and low cost of analysis. An outstanding aspect is the performance of more than one million analyses per year."

May 1, 2019

By B Cronin, M Gao, M F. Young

Fine grinding technology has become extremely important for Mount Isa Mines Limited in the last decade for flowsheet development for the McArthur River deposit and in rejuvenating the Lead-Zinc Concentrator at Mount Isa. Regrinding products with 80 per cent passing seven microns and 12 microns were required, respectively, for the McArthur River ore and the Lead-Zinc Concentrator at Mount Isa. Development of the ISAMILL, a horizontal stirred mill with a gross mill volume of 4000 litres (a net volume of 3000 litres), has been successful in delivering the required grinding product sizes with an energy consumption acceptable to a mining operation. The ISAMILL performance for processing both lead and zinc streams at Mount Isa is discussed in this paper, including the milling energy efficiency, the media wear and the size-by-size recovery data for one flotation process following the fine regrinding stage. The potential use of the ISAMILL technology at various phases of the mining cycle is also discussed.

Jan 1, 1998

By J. R. Perumareddi, V. S. Sastri, M. Elboujdaini

It is well known that high strength steels used in aerospace industry, are generally susceptible to hydrogen embrittlement during surface treatment such as electroplating with zinc on cadmium. Hydrogen embrittlement reduces ductility and results in brittle fracture rather than failure by plastic deformation. Hydrogen embrittlement of high strength steels is mitigated by surface treatment such as plating with other metals. Data on the hydrogen contents of steels before and after surface treatment by hot extraction-thermal conductivity, secondary ion mass spectrometry (SIMS) and UV-visible spectroscopy along with the mechanism are presented.

Jan 1, 2006

By G. J. Lindenburg

The Velvet mine is located in the Big Indian district of the Colorado Plateau. The general area, also known as the Lisbon Valley district, is about 65 kilometers southeast of Moab, Utah and about 120 Kilometers southwest of Grand Junction, Colorado. As shown by the slide, the Velvet area is typical of the high desert of the southwest United States. The elevation at the decline collar is 1,967 meters above sea level. To date, the Velvet has produced 1.5 million kilograms of U308 and 2.1 million kilograms of V205. The current production averages over 4,000 metric tons of ore per month. Access to the Velvet mine is by a 1,160 meter long decline. Fresh air is supplied through the decline and a 152 centimeter cased borehole. Contaminated air is removed by two 152 centimeter cased boreholes. The east side of the mine is mined using a conventional room and pillar method; whereas the west side is mined as combination conventional and random room and pillar,

Jan 1, 1983

By R. E. Cook

"Mineral deposits require substantial amounts of energy to transport and be processed into usable form and, as such, present a real processing challenge in that the deposits are never homogeneous and orebody compositional characteristics are all over the map. Extracting the desired mineral(s) from the deposit at sufficient profit margin, despite severe fluctuations in market price, requires process automation architecture capable of supporting an integrated enterprise solution. Such an architecture will encompasses the activities of individuals, process units, process areas, plant level activities, mine management and business planning, and accounting systems. Key to the automation process is the aspect of value generation. This article brings together the various requirements for the automation of a mining enterprise and presents the different aspects of how to obtain value across the entire mining operation.Minerals’ processing sites are historically long lived, with 20-year life-of-mine not uncommon and 75 years not unheard of. Considering that hardware technology advancements are introduced every six months, or less, it is prudent to select process automation systems that adhere to “open” industrial standards versus proprietary based systems. In the minerals processing industry, the key to survival is driving the cost of production per unit volume to the lowest possible level and provide enough profit to sustain operations. Control system architecture and business information technology are rapidly becoming important tools in the quest for productivity. Getting key dynamic business performance information at the right time to the right person or process unit is crucial to successfully achieving corporate goals. The process automation architecture selected must, therefore, be able to integrate to the various networking enterprises and business systems.The mining industry is generally known as an extractive industry that is physically oriented with respect to operations and the activities in which workers engage. Large numbers of people performing manual tasks in difficult surroundings, produce variable outputs. But times are changing – and so are industry best practices. While the nature of work still consists of activities such as ore extraction, ore movement, ore concentration, refinement and logistics, automation innovations are starting to change the nature of many of the production steps. The industry has transitioned from requiring more physical activities by workers to more information management, automated control and collaboration within the operation. Humans are good at situational intervention and nonlinear reasoning and do best when empowered with an overall production perspective. Machines and automation are good at repetitive functions, steady state operation, and managing transitions. Thus, a combination of advanced technology solutions, reliable and useful information and full human contributions are necessary to mining operations for value generation."

Jan 1, 2015

By G. E. d’Aquin

Sources of sulfur have varied based on technology and societal needs. It has been mined in its elemental form for centuries. Twentieth century technology brought thermal mining (Frasch, 1894) to the forefront of sulfur extraction. Then, by the 1980s, petroleum processing generated almost 40 percent of the 50 Mt (55million st) of sulfur in all forms (SAF) produced in the world. Metals processing (the reclamation of effluent gas by various means as “sulfur in other forms,” or SOF) followed at 30 percent of all sulfur values produced and then Frasch at 22 percent. Petroleum and gas processing now generate most of the elemental sulfur produced in the world. Single Two Frasch mines remain, one each in Iraq and Poland. Conventional mining of small to insignificant volumes also survives in Russia, Latin America and Indonesia. The volume of “recovered” sulfur (the name commonly given by the industry to hydrocarbon-derived material) generated will increase faster than energy consumption as oil and gas with greater amounts of sulfur are used and environmental restrictions on the sulfur content of the fuel consumed become more stringent.

Jan 1, 2005