Search Documents

By Tony Amis

There is very limited information relating to the potential impact of temperature cycles, outside the variation that occurs naturally, on the behaviour of foundation piles. Such thermal loading occurs when piles are used as heat exchange elements within a Ground Sourced Heat Pump system, in addition to carrying building loads to competent strata. An investigation has been undertaken where a conventional load test has been extended to include a period in which the load is maintained and temperature cycles applied. Instrumentation was installed in the test pile, an adjacent borehole, two of the anchor piles and the heat sink pile in order to be able to develop an understanding of the temperature variation and associated strain changes within and between the various elements. Conventional electronic strain and temperature gauges have been used in conjunction with optical fibre sensors which also measure strain and temperature changes. The results have confirmed the validity of the assumption made in the thermo-dynamic design of the system, the compatibility of the differing measurement systems and differing installation methods for the optical fibres, and initial assessment suggests that the load-settlement response of the pile is not adversely affected by the temperature cycles applied.

Jan 1, 2008

By Walter Díaz Cartagena

El suelo es uno de los recursos más importantes del agua -en tanto sustenta la vida natural y fuente de alimento para toda la especie terrestre. Por tal motivo, el presente texto señala los planes y estrategias para el cumplimiento de los estándares de calidad (EKA) de los suelos. En la promulgación de D.S. N°02 2013-MINAM que aprueba dichos estándares, se establece el último componente por norma para conocer la cantidad de contaminación del suelo. Este decreto propone una serie de etapas en la gestión de suelos contaminados que van desde la ecuación de los instrumentos de gestión ambiental, la investigación de situación de estos suelos contaminados en la zona de producción para determinar el estado en el que se encuentran y la recuperación ambiental por parte de un plan de descontaminación de suelos.

Jul 1, 2014

By J. Z. Yuan

The purity of rectorite is only about 70% after preliminary mineral processing, which has limited its application. In this research, different pulp densities, different dispersants, different dispersing methods and purification flow sheets were used to purify rectorite. The results show that it is possible to obtain high pure rectorite clay with the purity above 90% and concentrate yield between 24.9% and 29.4% by the purification process with composite dispersants, stirred mill grinding dispersion and so on. The obtained high pure rectorite can be further used in rectorite nanocomposites.

Jan 1, 2014

By W. A. Boyer

If the safety factor of a mine hoisting rope is checked for the lowest depth, is the rope then safe for all levels? The answer here is no. A new set of volues is proposed. HOISTS for metal mines are seldom designed for one particular depth. They are intended for an ultimate load and depth with a given speed but are first used to hoist from a shallower depth, gradually working to the ultimate as development progresses. Sometimes the mine is not worked on the upper levels because of the kind and grade of ore, the mining of which depends on market conditions. In this case the hoist may be used in the same working shift to lift ore, for example, from the 1200 and the 4400-ft level. This means that the safety factor of the rope should be considered not only when it hoists from the greatest depth, but also when it hoists from the upper levels. According to present safety factor standards, a hoisting rope can have ample safety margin when hoisting from the lower or lowest level and still be shy of sufficient safety margin when hoisting from the upper levels. This will be shown by curves presented in this paper. The safety factor of a hoisting rope as defined by the U. S. Bureau of Mines' is the ratio of the static load to the tensile strength of the rope. It is calculated by dividing the breaking strength of the rope* In Fig. 1 curves A and B are plotted against the vertical suspended distance, which is the abscissa, and the factor of safety, the ordinates. Curve C is a smooth curve drawn through the midpoints of the steps of curve A and would more closely represent the minimum factor of safety for new rope for any particular depth. Curve D is a smooth curve drawn through the midpoints of the steps of Curve B and would more closely represent the minimum factor of safety when ropes should be discarded for any particular depth. If a new rope were applied with a minimum factor of safety, then the vertical distance or ordinate under curve D for any particular depth, divided by the vertical distance or ordinate under curve C, would represent the minimum percent of remaining area intact that could be allowed before the rope would be discarded. Also, that section of the ordinate between curve C and curve D is proportional to the section of the area of the new rope that could be allowed for wear and broken wires. Considering that point at 2500 ft on the chart, the ratio do to co would be the minimum percent of rope area remaining at the point of discard. The ratio of that portion of the ordinate cd to co would represent maximum percent of area of a new rope available for wear and broken wires.

Jan 1, 1955

By Peijian Zhang, Yansheng Liu, Yuusaku Tominaga

The directions for ventilation control are often given in linguistic styles such as "if the airflow rate measured is small, a high value of rotation on a local fan should be chosen." In order to control the underground climate using a computer instead of a human being, both the reliability of data values measured underground and the application of human recognition of data values are required. The efficiency of data transmission is dependent on a method of checking a signal which is changed by mixing noises resulting from cases of electrical and mechanical damage to cables. In the study, fuzzy reasoning is adopted to choose a checking method for underground conditions from a normally operating state to an emergency. Fuzzy reasoning is applied to control airflow rate under the linguistic control rules given. It is shown that an effective series of linguistic control rules derived by fuzzy-sets theory is available in ventilation control when used in conjunction with an air velocity sensor, a computer and a local fan with thyristor control. Moreover, a system to make an optimum series of linguistic control rules for ventilation control is introduced.

Jan 1, 1987

By D. S. Kingery

The data obtained from this study cover test areas that are gassy to ultragassy and pillared areas of different sizes and degrees of tightness. The methods of controlling ventilation, applying bleeders, and supporting bleeder entries varied in the different test areas. It was not possible to study all conditions likely to be encountered in coal mines. Undoubtedly, there are areas where bleeder entries, even though properly planned and maintained, might prove unsatisfactory. However, on the basis of this study, the following observations were made: 1. Tests showed that each bleeder system studied provided some movement of air through the pillared area; the quantities of air delivered to the pillar line, ranged from 23 to 82 percent, depending mainly on the extent to which bleeder re-turns were used as main returns from the section. 2. Pressure measurements taken across pillared areas showed maximum pressure drops ranging from 0.05 inch of water for a shallow gob to 2.69 inches for a very deep gob. The pressure differentials varied with the size and tightness of the gob but proved adequate to induce airflow across worked-out areas or through fringes of the gob to the bleeder return system.

Jan 1, 1957

By Frederick J. Hoppe

The productivity or usefulness of a Front End Loader rises rapidly with its size. Loading is more aggressive. Mother Nature is defeated more easily. Larger tires get a better grip on the ground. Hauling equipment can be loaded more quickly. The productivity or usefulness of a Front End Loader is proportional to its working speed, both automotive and hydraulic. The price of speed is horsepower, which rises rapidly with speed. Horsepower saved shows up as increased productivity. This paper covers the development of the D600, KW-Dart's articulated loader, which combines massive size with new concepts to increase its working speed. Featured is a discussion of the horsepower saving, "Balanced Boom."

Jan 1, 1969

By Marek Wilczewski, Kristine Uhlman, Darrel Sipe

With the end of active copper mining in 1983, the extensive underground mine workings and the Berkeley Pit, one of the largest open-pit mines in the United States, began to flood. Daily in- flow to the pit is about five million gallons per day, with the water level rising at a rate of 30 feet per year. To support the remedial investigation and feasibility study, a six-layer, three-dimensional MODFLOW-based ground water flow model was constructed to simulate the 9,100-acre site. The vertical domain of the model extended over 1,060 feet of elevation difference and consisted of a finite difference grid of 89 rows by 54 columns. All work was PC- based. Model boundaries were assigned to correspond to natural hydrologic features such as geologic contacts, faults, and surface water features. The fully calibrated model was approved by the State of Montana and the U.S. Environmental Protection Agency (EPA) for use in the site remediation. The computer model was used to determine ground water flow velocities and contaminant travel times within the alluvial sediments adjacent to the Berkeley Pit. The purpose of the model was to predict future alluvial ground water flow directions should acid- and heavy metal-laden flood waters filling the Berkeley Pit rise up and enter the Alluvial Aquifer.

Jan 1, 1996

By D. W. H. Su

This paper describes geomechanical criteria employed by Consol Energy for selecting mine-specific longwall face supports in the past decade. The criteria include immediate and main roof rock characteristics, floor rock characteristics, critical tip-to-face distance and shield operating range. Detailed roof rock properties from high-density core holes as well as in-mine scope holes are used to evaluate the set load density and shield stiffness required to control the immediate roof and the yield load density required to absorb the load density developed from main roof weighting. Detailed floor rock properties from core holes and in-mine floor bearing capacity tests are used to specify the maximum peak toe pressure as calculated by the Jackson method. The critical tip-to-face distance is evaluated based on the immediate roof rock strength, layering and thickness. The shield operating range is evaluated based on main bench thickness, the presence of thick draw slate, the potential of minor roof falls at the face and transportation restriction. Three case examples representing three different geologic conditions are presented to illustrate the successful application of these geomechanical criteria for selecting longwall face supports within Consol Energy in the past decade.

Jan 1, 2004

By P. Ramsaywok, S Ndanduleni, G. Legodi

The objective of this paper is to share the optimisation journey of a pilot Reflux classifier (RC) circuit in the Exxaro GG1 plant, at Grootegeluk beneficiation complex in Lephalale, South Africa. The RC circuit was commissioned in 2016 to produce semi-soft coking coal at its fines circuit; however the stability of operation as well as the quality control of the coal product was not fully achieved. Various test campaigns and optimisation studies were conducted to understand and optimise the RC circuit at GG1. The studies revealed circuit design inefficiencies; provided an improved technical understanding of the current pilot circuit and the parameters required for the circuit to reach a stable operation. The operation was stabilised with its current inefficiencies to produce an average 12.5% ash semi-soft coking coal product for sustained periods, above the initial target of 10.3% ash. Keywords: Reflux classifier, coal

Jan 1, 2020

By G. R. Green

The centre of the mining operations of the International Nickel Company, Ontario Division is Sudbury, a city of 160,000 population located 240 miles northwest of Toronto (Fig. 1). Within thirty miles of this city and located around the rim of the geological formation known as the Sudbury Basin are the ten underground mines and one open pit operated by the Company (Fig. 2). There are also four developing mines, three in the Sudbury area and one at Shebandowan, near the city of Thunder Bay, Ontario and approximately 150 miles north east of Duluth, Minnesota. In 1971 the mines produced 22,800,000 tons, 20,600,000 tons from underground and the balance from open pits. Also located in the Sudbury District are facilities to extract and refine the metals contained in the ore. There is a nickel refinery located at Port Colborne on Lake Erie. An additional nickel refinery is under construction near Sudbury. Fifteen elements are recovered from the Sudbury ores, nickel, copper, iron, sulphur, gold, silver, cobalt, tellurium and the six platinum group metals, platinum, palladium, iridium, rhodium, ruthenium and osmium. In 1966 a major expansion program was undertaken to meet increasing market requirements. Coinciding as it did with a severe

Jan 1, 1972

By N. D. Policow, J. S. Orphanos

D.A. Dahlstrom In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in Fig. 4. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in Fig. 4. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensors, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89¢/t (81o; per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed. ? Reply by N.D. Policow From a technical standpoint, a number of extensive test programs have demonstrated that by raising the feed temperature, mechanical dewatering is enhanced whether it be centrifuges or filters performing the separation. Economic constraints usually become the over-riding issue. If an inexpensive source of thermal energy is available, i.e., waste steam, etc., the approach becomes commercially acceptable. For the specific case of coal slurry pipelines, since the dewatering plants will be located close to power generation stations, the preheating approach becomes especially attractive. The cost comparison shown in Fig. 7, which was prepared by a major West Coast engineering firm, contrasted screen bowl centrifuges and disc filters. In both alternatives, a thermal dryer was specified to produce a contract moisture of the final product. Sizing of the thermal dryer on the screen bowl alternative was substantially smaller than that of the filter, since the screen bowl was credited with a four to six percentage point decrease in product moisture compared to the disc. This comparison was made at ambient temperatures and reflected solely the mechanical dewatering capabilities of the two devices. No preheating of the feed was included in this particular comparison. Early generation screen bowl centrifuges operated under the principle of maximum bulk tonnage throughput. Second and third generation machines have followed the trends dictated by the coal industry calling for higher one-pass recoveries than previously demanded. The current generation of high-speed, long-bowl centrifuges permit recoveries of ultrafine solids directly comparable to commercial filter operation. On typical coal preparation plant feeds with nominal 600 E. an X 0 (28 mesh X 0) clean coal, recovery levels in excess of 99% are now obtained. The material that does escape the centrifuge and reports to the main effluent is typically -10 µm, high ash material. We have documented substantial beneficiation effects in screen bowl centrifuge performance with the cake product containing lower ash levels than the feed. On the referenced pipeline, coal tests performed on Western subbituminous coal, we found that the percentage of -10 µm material in the feed was six to eight times greater than normally encountered on eastern Appalachian seams. Our 45-t/h (50-stph) production centrifuge was never set up to maximize recovery. It was used as part of the two-stage dewatering circuit that had been chosen by designers of the proposed pipeline. Recoveries up to 95% were recorded. With field adjustments, that performance could most certainly have been improved. In contrast, manufacturers of the horizontal belt filter provided a small pilot-scale unit that operated on a side stream at the test facility. Numerous combinations of chemical additions were evaluated to determine those that had the best impact on filter performance. Whereas the screen bowl centrifuges operated without chemical addition, producing a dry, fluffy cake, the belt filter required two stages of chemical addition to attain satisfactory performance and high recovery levels. On the two-stage circuit that incorporated a belt press as the secondary

Jan 12, 1983

By Carl M. Fellman

LABOR disputes caused considerable turbulence in the coal mining industry during 1946. As an outcome of these disputes, a definitely fundamental change in safety procedure was instituted: establishment of safety regultions for coal mines through the agency of agreements between the miners' union and the agency or agencies operating the coal mines. Although a temporary plan at present, the future will determine the. extent to which it may become permanent. Notwithstanding the turmoil in the industry extending through much of the year, the safety record for the first eleven months of 1946 was the best in the history of the industry for that period. The fatality rate for 1946 is lower than in any other year in the history of coal mining in the United States. This follows a pattern inasmuch as new low coal-mine fatality records were also made in 1945, 1944, and 1943. The five-year period 1942 to 1946 inclusive has a coal-mining fatality rate far lower than any other five-year period in the history of the industry. It is significant that this period exactly coincides with the operation of Federal coal mine inspection which got under way early in 1942.

Jan 1, 1947

By F. Smit

Mining and plant disciplines can benefit from pre-concentration of UG2 platinum ores in a dense medium separation (DMS) plant. The main benefit of DMS is the selective discard of waste from the feed stream, thus improving project economics while reducing the power and water requirements for processing. On the mining side, with the correct combination of variables, implementing DMS as a pre-concentration step can reduce cut-off grades and, as a result, increase ore reserves. In addition, the use of DMS technology gives the mine team the opportunity to consider alternative mining methods for an operation. The challenges of balancing the mining tonnage, methods, and resulting grades with the process plant size, recoveries, and DMS discard volumes have resulted in the development of a model to optimize value on new projects or existing operations. This paper will focus on these benefits from a mining and plant perspective, quantifying the water and power savings, and look at the economic benefits of pre-concentration and the effect of metal prices, plant feed grade, and DMS efficiency in different mining environments.

Jan 1, 2012

By Richards RG, Cross MS

The development of alluvial mining, processing systems and associated gravity separation technology over the last 30 years is largely linked to the mineral sands industry. Attention has been focussed on Australia in these areas of mineral resource development and technological Advancement.

Jan 1, 1986

By d&apos, E. Appolonia

A construction project is successful when all parties contributing to it are winners. It is not a success when there are winners and losers. Con­tractors, engineers, suppliers and equipment developers, and especially owners, each can contribute and benefit from a revaluation of attitudes and contacts from planning to final payment. The Deep Foundations Institute was initiated with this as its major purpose. The help of educators is essential to promote this with the next generation. The Association of Soils and Foundations Engineers has developed guides for "Mediation Arbi­tration of Construction Contracts."

Jan 1, 1985

By Bill Loviza, Jimmy Sanders

This report is not everything we would like it to be. Access to information concerning unresolved legal actions is a sensitive matter. Obtaining the information presented in this report was a challenge alone. The Tennessee Department of Commerce and Insurance, Division of Fire Prevention, the firms and individuals that elected to share information did so with various assurances of nondisclosure, confidentiality or anonymity. All those providing information did so with the expectation that the industry and ultimately the public would benefit from this effort. We offer special thanks to Assistant Commissioner, Fire Prevention, Emmett Turner, recently retired Director, Bomb and Arson, Dick Gardner and Director, Codes Enforcement, Randy Safer for support that made this endeavor possible. We make no claim with regard to being a scientific study. We did the best we could with available information. Our task was one of assembly, sorting and reporting. Where collateral information was available we used it.

Jan 1, 2004

By Qinghai Pang

"With the increasing proportion of bituminous coal in blend coal, the safety of blend coal during pulverization and transportation is gradually being paid more and more attention. Therefore, the explosivity of bituminous pulverized coal (PC) with different volatile content from 25 to 38% was studied by measuring the combustion flame length after its injection into a glass pipe with the heat source installed in the center. The results indicated that high volatile content bituminous PC is apt to have higher explosivity. By blending different bituminous PC with 10% anthracite, the explosivity of bituminous PC showed a positive correlation with the proportion –OH radical. However, different bituminous PC seemed to have the same explosivity when the addition of anthracite increased to 20%. With the further increasing proportion of anthracite to 30%, the explosivity of bituminous PC with high –OH proportion became negligible while a weak explosivity of high –CH3 proportion bituminous PC still remained.IntroductionWith the increasing iron ore prices and decreasing steel prices, it has become critical for iron and steel enterprises to control the cost in ironmaking and steelmaking process. Blast furnaces (BF) are the main consumer in ironmaking process, which occupies 70% fuel consumption of total steelmaking process [1]. In this circumstance, any means necessary is taken by BF operators to lower the cost of iron in production. Coke and iron ore are the main expense in this process, who takes up a very high proportion in total cost. Pulverized coal injection (PCI) is the most efficient way to reduce coke ratio, which replace coke with relatively cheaper PC.At present, most of BF is injected with blend coal in the consideration of decent combustion property and quantity of heat. Simultaneously, bituminite and anthracite blending is an effective method to obtain blend coals with required composition and performance, such as volatile and ash content, etc. Nevertheless, a very huge gap was found between the price of bituminous coal and anthracite in some regions of China, in which the price of bituminite can be just 70% of the price of anthracite. Thus, iron enterprises in these regions attempt to possibly amplify the proportion of bituminite in blend coal. Increasing proportion of bituminite results in higher volatile content in blend coal, by which the safety of blend coal during pulverization or transportation was deteriorated.Relatively, coals with higher volatile content usually possess stronger explosivity, which means that volatile and explosivity may related to some extent. However, the relationship between volatile and explosivity is not of certainty for some PC with high volatile content around 40% was found to be inexplosive in comparison to the coals with lower volatile content. With the increasing proportion of bituminous coal in blend coal, investigations on the factors of PC explosivity have become more and more important. Therefore, bituminous coals with different volatile content were selected. The explosivity of blend coal and its relationship between volatile content and functionality was investigated in this research."

Jan 1, 2014

By C. Guo, R. J. Chalaturnyk, M. MacKinnon, J. D. Scott

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd. oil sands plant. Over the past years (since 1996), there has been a marked change in the densification behaviour of MFT in the MLSB. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings) at the area with intense microbial activity. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. It may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program was carried out to study the mechanism leading to the rapid densification phenomenon. A review and discussion of the research program is given and some results from the field investigations and small-scale column tests are presented in this paper.

Jan 1, 2007

By Danu Putra, Budi Sulistianto, Tri Karian, Mohammad Nur Heriawan

Stope layout optimization is an important feature of underground mining that maximizes the economic value of the project while taking mining limits into account. The large number of parameters and constraints makes it difficult to obtain the optimum condition. Several algorithms have been created to address these problems using a variety of methods. However, the circulating method has not explicitly included stope dimension stability analysis, resulting in a solution that is not stability-proven, which can result in a suboptimal solution. This study integrates the Mathews stability graph into the stope optimization algorithm so that the optimized stope layout considers stability conditions directly through an assessment of the available geomechanical data within the block model. The proposed algorithm is validated through a case study of a synthetic block model created by considering variations in grade and the geomechanical conditions of the rock. Furthermore, several scenarios are created to compare the performance of the algorithm that applies variations in stope sizes with the common case study of stope sizes that remain fixed. A more detailed assessment is also conducted on each final stope layout wall to ensure the successful application of stability analysis in the proposed algorithm through back analysis on the Mathews stability graph. The optimization results show that all walls in the final stope layout fall into the stable condition. Also, the proposed algorithm is also capable of maintaining the project’s economic value. Ultimately, the proposed algorithm can be deemed applicable and suitable for use in the initial stages of mining as a comprehensive assessment of the optimal stope layout, taking into account the stability conditions of the stope.

May 22, 2024