Search Documents

By Arthur Notman

In view of the alarm expressed in many quarters over the increased production of copper to come from Canada and Africa in the future, it is of interest to study the history of the principal producing districts of the world and to attempt to forecast the future part to be played by them. Tables 1 and 2 record the world production and that of the United States, together with their respective rates of increase, both in percentage and actual amounts. The important point in this record is the decline in rates of increase for both the world and the United States, but more particularly in that of the latter, since 1881. The increase for the United States in the last decade is less than that for any decade since 1881, and is only 20 per cent of that for the decade 1911-20. The increase for the world is less than that for the two preceding decades, and is only about 65 per cent of the war decade 1911-20. Referring to Table 1, the decade 1871to1880 showed an increase of 32.l per cent in the world's production, which was the low until the last decade, ending 1930, which shows an increase of only 24.5 per cent. These decades both represent periods of economic stress following wars. In the first case the recovery was very sharp, the percentage increase in 1881-90 reaching a high of 86.4 per cent. It would seem dangerous, however, to assume that a similar high will be reached in the next ten years, because of the severity of the depression brought about by the Great War and the probability of its influence extending well into the next decade.

Jan 1, 1931

By Min Chen

A numerical simulation of the stress field of the solidified shell in the mold during continuous casting of peritectic steel slab was calculated with commercial software. The results showed that the maximal stress on wide face of the solidified shell was located at the corner and near middle of the slab, and it increased with increasing the width of slab. In addition, the stress was also influenced by operating parameters such as superheat degree, drawing speed and cooling intensity of the mold, and the maximal stress value and its position changed with these parameters. For the slab with section size of 3200mm×150mm, the proper drawing speed was around 1.2m/min, with cooling intensity of 5500L/min while the superheat degree was 15°C to 25°C in order to prevent longitudinal crack occurring during peritectic steel continuous casting.

Jan 1, 2009

By V. I. Lakshmanan, Dan A. Mackie

Traditional vat leaching methods have had limited success, primarily due to the high cost of loading and unloading the vats. In general, such batch methods are labor-intensive and costly. Heap leaching has emerged as a viable, low- cost alternative, but low recoveries, normally in the 70% range, offer opportunities for improvement. Also increased regulatory guidlelines for effluent and spent heap leach pads disposal offer potential for alternative methods. The Mackie Vat Leaching Jig (MVLJ) has had its incubation at Ortech International, where bench scale through pilot scale testing continues. Design developments and testwork over the past two years indicate that the time may be right for field trials.

Jan 1, 1990

By N. A. Smith, R. J. Fowell, J. L. Hislam

Abstract: Data are presented from two sites in southeast England, where problems were encountered in tunnelling through ground containing flint. In response to the difficulties, substantial laboratory testing programmes were initiated to determine the strength of the flints.It is shown that the strength varies very considerably, even within a single flint particle and that the practice of estimating unconfined compressive strength by a single multiplier applied to the point load strength index (Is(50)) may give misleading results. The preparation of UCS specimens for testing was found to be very difficult and it is recommended that tunnel machine capacity is assessed relative to Is(50). Résumé: Des données sont presentées sur deux sites dans le sud-ouest de l’Angleterre,où le perçage d’un tunnel dans un sol contenant du silex a posé des problémes. En consequences de ces difficultés, des programmes substatiels de recherché en laboratoire ont été initiés afin de déterminer la resistance des silex. Il est demontré que la resistance varie considérablement, même au sein d’une particule de silex, et que la pratique de estimation de la résistance en compression non confinée, (UCS) par le biais d’un simple coefficient appliqué au ‘point load strength index (Is50)’ pourrait donner des resultants trompeurs. La préparation de specimens UCS destinés aux tests s’est avérée trés difficile et il est recommandé que la capacité de la machine de perçage de tunnels soit calculée relativement au Is50. Zusammenfassung: Daten von zwei Standorten in Südosten von England, wo Probleme beim Tunnelbau durch feuersteinhaltigen Grund antraffen, sind angegeben. Wegen diesen Schwierigkeiten wurden Laboratoriumsforschungsprogramme eingeleitet, um die Festigkeit von Feuersteinen zu bestimmen. Es wurde gefunden, dass die Festigkeit sehr unterschiedlich war, selbst bei einzelnen Feuersteinstücken, und dass die Praxis, die unbegrenzte Kompressionsfestigkeit (uKf) auf Grund eines einzigen Multiplikationsfaktors vom Punktladefestigkeitsindex (Is50) abzuschätzen, zu irreführenden Resultaten führt. Die Vorbereitung der uKf Prüfstücke war sehr schwierig und es wird vorgeschlagen, dass die Kapazität der Tunnelbaumaschine in Abhang der Is50 bestimmt wird.

Jan 1, 2003

By Muhamad Firdaus

There is a growing interest in Magnetoelectric (ME) materials in view of both fundamental understanding and novel desirable applications. The application potential for multiferroic materials with the possibility of reversing the magnetization by applying an electric field (or vice versa) is quite promising especially in data storage application. The rare earth ortho-ferrites (REFeO3), such as NdFeO3, have been studied extensively in recent study in the context of discovery of magneto-electric (ME)/multiferroic nature materials. In this paper a potential high temperature recovery of rare earth elements in the form of REFeO3 from waste permanent magnets using direct oxidation in air was investigated. It was found that REFeO3 (NdFeO3) phase can be separated from the other oxide phases by thermal treatment of NdFeB magnet waste at 1100 °C in air atmosphere. The REFeO3 also found to have different physical characteristic (density) from the other layers and can be separated physically. This paper will include a proposed flowsheet to recover Nd as NdFeO3 through powder separation. The technique can be beneficial and favourable for RE recycling and recovery from waste permanent magnets.

By Thomas P. Mucho, David C. Oyler, Jim Pablic, Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to be abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1,000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

By Sam H. Patterson

This paper is concerned primarily with the kaolin deposits extending northwestward from Macon, Ga., which is in the western part of the Irwinton district (fig. 1). These deposits are in a belt of kaolin districts extending along the inner edge of the Coastal Plain from the Aiken district, S. C., southwestward to the vicinity of Macon, a distance of 150 miles (250 km). Large kaolin deposits associated with bauxite also occur in an extension of this belt southwestward from Macon as far as the Eufaula district, Ala., a distance of about 130 miles (208 km). The belt splits away from the inner edge of the Coastal Plain in a southwesterly direction from Macon; the Eufaula district is approximately 50 miles (80 km) south of the contact of Coastal Plain sedimentary rocks with much older crystalline rocks. Structure The strata of Cretaceous and Tertiary age containing the kaolin deposits all dip gently seaward irom the landward edge of the sedimentary rocks. The dip of the Cretaceous strata is about 25 feet per mile (4.9 m per km). The dip of Tertiary strata is about 15 feet per mile (2.1 m per km). In places, the Tertiary strata overlap the older sedimentary beds and rest directly on the crystalline rocks. Faults having a few feet of displacement have been observed in several mines, but no major faulting is known in the area.

Jan 1, 1977

By Lewis Gordon, Alan Morrow, Aundra Nix

At the ASARCO Mission Mill, a multivariable, predictive controller was used to optimize parallel grinding circuits, improving throughput and product size. Using a dynamic model of the grinding circuit developed from on-line testing the software manipulates 4 variables to control 14 quality and constraint variables in each circuit. Traditionally, model-based control in grinding is difficult due to ore changes. This is addressed via a novel method to predict mill overload and automatic model switching.

Jan 1, 2000

By J. P. D. Strydom

The transmission of excessive vibration to the human body can cause physical stress that may result in crippling pain or permanent disability. Rock drills are known to transmit high levels of vibration that are difficult to attenuate through conventional approaches to vibration isolation. However, it can be shown that once the ISO frequency weighting has been applied, most of the vibratory effect of the rock drill?s motion is concentrated at the drill?s operating frequency. This observation opens the way for utilizing a concept known as vibration absorption, aimed at attenuating the rock drill?s vibration. In essence this entails using the inertia of a secondary vibratory system to counteract the motion of the handle. This article documents an investigation into the use of such an absorber for attenuating rock drill vibration and demonstrates the feasibility of such an approach. A mathematical model of such an absorbing handle was developed and used for design studies. Based on these investigations an experimental prototype model was manufactured and tested. A significant reduction in vibration levels could be achieved.

Jan 1, 2002

"On-site research and development as well as in-situ testing are key factors to the successful implementation of new mining equipment and technology. Unfortunately the demands and necessities of research and development often conflict with the reality of mine production in operational mines, especially during early stages of research and development and the initial testing of new equipment. Several experimental mines under university supervision attend to this problem and provide a close-to- reality testing environment for the mining industry and mining equipment manufacturers. This paper gives an overview of the design and organization of such an underground testing area as well as of the wide range of possible operations it can facilitate at the example of the FLB Experimental and Teaching Mine (Forschungs- und Lehrbergwerk) at Technische Universität Bergakademie Freiberg, the central European underground research mine. INTRODUCTION As well as the Mining Engineering education follows the same pattern worldwide, the tasks and duties to be fulfilled by engineers in the productive mines are comparable around the globe. This also holds true for the technologies and equipment needed, both in surface and underground mines. Almost all mining equipment brands are being distributed worldwide. The tasks and challenges of guaranteeing an ever- increasing productivity at the mines, while simultaneously maintaining, respectively improving, safety standards, also in the developing countries and emerging economies, requests a constant development, improvement and adaption both of the engineering education and of R&D in technology and equipment. The increasing safety requirements at the mines, in combination with also increasing safety and liability policies, do often not allow a proper practical education of mining engineering students. At the same time, new technologies and equipment to be deployed / brought to the mines have to be fully functional in a production operation from the very first moment. Time losses like break-down time or even repair and maintenance breaks are often costly and, even when expected up to a certain degree with newly developed machines, have a wider negative impact on the neighboring operations and operations within that mine, thus often being unacceptable within the ongoing production process and extremely costly."

Jan 1, 2015

By K. L. Gabby

Selective removal of mercury from cyanide leaching solutions while retaining silver has been a long-standing problem, due to the chemical similarity of mercury and silver. In order to be practical, a mercury removal process needs to be both highly selective and use inexpensive materials. This paper reports the use of zinc sulfide (ZnS) as a precipitant for mercury. The mercury cyanide complex (Hg(CN)4 2-) undergoes a replacement reaction with the zinc sulfide, forming insoluble HgS, while the silver cyanide complex (Ag(CN)2 -) remains in solution. Under appropriate conditions, the separation of mercury from silver is nearly quantitative, with close to 100% removal of mercury, while nearly none of the silver is precipitated.

By Joseph Harrington

It is sufficiently correct to say that domestic solid fuel is universally hand fired and it is almost as correct to state that a very large proportion of hand-fired domestic fires are extremely inefficient and smoky. This is particularly true with raw bituminous coal for the fuel. The smokeless and efficient firing of domestic coal affords one of the most difficult problems confronting the combustion engineer. This is due to the universally constricted combustion space in the domestic furnace, the complete ignorance regarding the laws of combustion on the part of the average person, and the fact that the laws of efficient combustion are almost completely nullified under these conditions. It is well to familiarize ones self with these laws. These are: 1. The gradual introduction of the fuel to the furnace. 2. The admission and mixing of the right quantity of air with the coal gases. 3. A temperature high enough to permit complete combustion, and 4. A furnace space of volume sufficient to permit of the combustion gases and the oxygen getting together within the confines of the furnace. Even a casual inspection of the domestic heater will show that none of these essential things are present in proper degree, and this is the reason why the problem of domestic firing presents such difficulties. I have analyzed these conditions in a paper published by the Black Diamond, and which has already had wide distribution, so that I will not repeat the rather lengthy discussion in this paper. A survey of the entire field indicates very clearly that a reversal of existing methods and equipment must be had before any real improvement can be expected. It is my firm belief that in this instance above all others it is necessary to build the efficiency and smokelessness into the equipment in such a manner that its performance will be entirely independent of both skill and interest on the part of the operative. To attempt to educate every man, woman and child who periodically throws coal into a domestic furnace would be literally impossible. Much can be done, however, if we could teach the householder the simple essentials of alternate firing, which I have explained at length in the above mentioned paper. This would go a long way toward making the domestic furnace problem more satisfactory, as well as efficient and smokeless. Many will argue, and with good reason, that the domestic fuel should be prepared coke and with this I agree up to the limit imposed by the practical considerations of quantity production, price and the possibility of marketing the by-products. It will be obvious that if enough raw coal should be processed to provide all of the required domestic fuel that the amount of by-products recovered during the coking process would be so great that there would be little or no market at any price which would justify the manufacture of coke. If the by-products were wasted they would not only be a tremendous economic loss, but the price charged for the coke would probably be so high that the market would be limited, and this would defeat the very idea of the whole thing. Much can be done, however, in advancing the use of coke, but I believe that much more extensive and careful experimentization should be had in order to determine the right size and quality of coke for the various domestic furnaces. If coke were to be developed for extensive domestic consumption it is more than probable that the coking process should and could be stopped at a point where the volatile content of the coke would be sufficiently high to permit of prompt ignition and combustion in low draft installations. If the volatile content were from five to ten per cent a very different kind of coke would be produced from that which is now produced with perhaps one per cent of volatile. A skillful manipulation of this feature would make coke adaptable and satis-

Jan 1, 1925

By P Wilson

The Mt. Wright Underground Mine is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. The establishment of the world’s first Sub Level Shrinkage (SLS) mine from a tradition Sub Level Open Stoping operation has proven to be a geotechnical challenge which has required tailored solutions to overcome unique issues. This paper will be broken into two distinct sections that will outline: a brief overview of the mining method and how the SLS method was chosen; and how the SLS is managed and key geotechnical learnings. The story of the world’s first SLS originated from the need of a bulk mining method to ensure the viability of Mt. Wright into the future. Traditional bulk mining methods such as; Block or Sublevel Caving were originally ruled out due to the low natural ‘cavability’ of the orebody and the proximity of the orebody to existing major infrastructure (Decline, Ventilation Rises and Egresses). The first section of the paper will outline the key geotechnical information that helped decide the SLS method in addition to how continuous backfill influenced the design. The second section is intended to address issues that the geotechnical engineers encountered since the inception of the SLS. The feature topic of this section is mining induced stress. Like most bulk mining methods, Mt. Wright had success when the production front was running parallel to the stress (production front being ‘shadowed’ from the stress). This was until a design change, forced by a splitting ore body resulted in this shadowing effect becoming harder to achieve. As a result, rehabilitation and production hole re-drilling become a regular occurrence, which teamed with a strict set of access controls made the production cycle longer and harder to complete. CITATION:Wilson, P, 2018. Mt Wright – geotechnical learnings from a sub level shrink, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By B. C. Williams

The Bureau of Mines monitored the water quality in and near a copper/gold tailings impoundment. Samples were taken from the unsaturated %one. and dissolved concentrations of over ZO constituents were measured with respect to depth and moisture content, factors which influence oxygen content and sulfide oxidation. Samples from the unsaturated %one were drawn through a hypodermic needle sampler into individually evacuated vials fitted with septa, thus preventing oxygen contamination. Water quality was also monitored in the saturated tailings, underlying colluvial aquifer, and weathered andesite bedrock.

Jan 1, 1989

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By A. E. Lewis, J. Du Plessis, J. Chivavava

Current metallurgical processes lack selective and efficient REE recovery from aqueous leach liquors. Antisolvent crystallisation is used to selectively recover pure inorganic salts from aqueous solutions without excessive chemical use in ambient conditions. Yttrium sulfate octahydrate (Y2(SO4)3.8H2O) was used as a representative rare earth salt to investigate the effect of antisolvent selection on the crystal morphology and size distribution of the final crystalline product produced through antisolvent crystallisation. The antisolvents of choice were short length alcohols that are water miscible i.e. methanol, ethanol, 2-propanol and t-butanol. All experimental parameters except the type of antisolvent were kept constant under isothermal conditions. The large reduction in solubility of the salt by the antisolvent creates high supersaturations. This leads to high product yields as observed in this study at > 91%. In general, a variety of morphologies were successfully formed in each individual alcohol including; rods, plates, prismatic cubes and starburst clusters. The powder X-ray diffraction (XRD) analysis indicated that Y2(SO4)3.8H2O was the only species present for all final products. There was a change observed from the starburst and rod structures for the shorter alcohols towards prismatic cubes for the longer alcohols due to different strengths in the solute-antisolvent interaction at the crystal growth faces. The crystal sizes increased with an increase in the alcohol chain length because of the lower supersaturation conditions due to a limit in the mass transfer induced by the bulkier alcohol structure. In conclusion, it has been shown that the particle morphology and size can be greatly affected by the selection of antisolvent even under high supersaturation conditions, contributing to understanding the effect of different antisolvents on the final particle characteristics. The engineering of favoured product characteristics can therefore be achieved by antisolvent crystallisation, presenting a viable alternative process for the recovery of REE. Keywords: Antisolvent crystallisation, rare earth elements, morphology, particle size

Jan 1, 2020

By C. Musingwini, M. Mohutsiwa

"SynopsisCapital cost estimates are important in decisions on whether a project will be approved, mothballed, or abandoned. In South Africa, junior coal miners do not have extensive databases of historical projects from which to estimate capital costs. The purpose of this paper is to establish formulae that can be used for estimating capital costs of developing coal mines in a coal-producing country, using South Africa as a case study. The costs are estimated to an error of magnitude level of -30% to +50%, which is suitable for a concept study level, using a parametric estimation technique. The study uses data from completed coal mining projects from selected coal-producing countries. Three formulae are developed and presented for estimating capital costs of underground bord and pillar, surface shovel and truck, and dragline operations.IntroductionCapital cost estimates play a critical role in deciding whether projects will proceed, be delayed, or abandoned. It is therefore important that capital cost estimates are carried out accurately as determined by the estimation guidelines based on the level of estimation conducted (Shafiee and Topal, 2012). The lack of literature on estimation of capital costs in many coal mining countries is adversely affecting junior coal miners, since they do not have an extensive database of historical projects on which to base estimations. In South Africa, the difficulty in estimating capital costs is attributable to lack of publicly available data on completed South African mining projects (Hall, 2013)."

Jan 1, 2015

By K. K. Kelley

Sodium-aluminum and potassium-aluminum silicates are among the more important rock-forming minerals of the earth's crust. They also appear as constituents of some metallurgical slags and of some refractory materials. Consequently, knowledge of their thermodynamic properties is interesting and valuable from several viewpoints. This paper reports experimental determinations of the low-temperature heat capacities and entropies at 298.16° K. of albite, jadeite, and nephelite it the sodium-aluminum silicate series and of adularia, ferriferous orthoclase, leucite and kaliophilite in the potassium-aluminum silicate series. Also high-temperature heat-content and entropy increments about 298.16° K. are reported for albite, jadeite, nephelite, and carnegieite in the sodium-aluminum silicate series. Except for a few high-temperature heat-content values for albite, all these data are available for the first time.

Jan 1, 1953

By Q. Zhang

The flotation behavior of jamesonite was investigated with ethyl xanthate as a collector. It has been shown that jamesonite has good floatability from pH 2 to pH 12, and relatively poor floata-bility at pH>12. The flotation of jamesonite was also dependent on pulp potential at certain pH val-ues. The potential-pH range for jamesonite flotation was established. The FTIR spectroscopy analy-sis and XPS measurement showed that the major adsorption product of ethyl xanthate on jamesonite was lead ethyl xanthate and antimony ethyl xanthate. The intensity of the FTIR signals of metal ethyl xanthate adsorbed on jamesonite and the flotation response of jamesonite were correlated with pulp potentials.

Jan 1, 2014

By S. Devereaux, P. Gover, S. Everett

Having real-time data of blast furnace burden profile with respect to burden height and temperature is critical to making informed decisions on blast furnace operation. Given the high temperature and gaseous environment within the blast furnace shaft, traditional instrumentation has been limited at providing the level of real-time feedback information needed to optimize blast furnace operations. Infrared thermal imagery technology provides non-contact temperature measurement across the entire burden profile, allowing for better understanding of the dynamic movement of the burden within the blast furnace shaft. This technology increases blast furnace performance by improving the decision-making process for hour by hour operations. This paper will discuss the development of incorporating infrared thermal imagery technology into the operating strategy of a lead blast furnace.

Jan 1, 2015