Search Documents

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By D. L. Martin, E. R. Parker

IN a previous paper, one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with, and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a strengthening, so that a longer life at a given stress and temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver .2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. EXPERIMENTAL PROCEDURE Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1943

Tailings embankments can develop a high phreatic surface if the original design for the embankment does not include drainage facilities or if existing drainage facilities become ineffective. Subsequent raises can develop a seepage surface due to a high phreatic surface that can lead to stability problems. The U. S. Bureau of Mines amended contract J0100013 to initiate this study of horizontal drains in tailings embankments. This study developed a technique for determining the length of and spacing between parallel drains through the use of the finite element model UNSAT2. The analysis is based on the combined output of a vertical planar mesh and a horizontal planar mesh. The slot opening in the drain pipe and the length of the perforated section are determined from an analogy to water well design. The pipe diameter and gradient can be determined from Manning's equation. To the authors' knowledge, this is the first attempt at horizontal drain design using a finite element model. Additional research is recommended in this area.

Jan 1, 1982

By P. Latostenmaa, T. Hailemariam, M. Lundström, P. Halli

Doré process is unique way to treat precious metals in the copper electrorefining plant, since it uses anode slime as a raw material. In this pyrometallurgical process, also slag is produced together with Doré metal. However, the process is never ideal, and a part of metal is always lost into the slag. By using Doré slag as raw material for simply mineral acid leaching, some of the lost elements can be extracted and recovered, thus, increasing the sustainability and keeping metals in the circular economy loop. The Doré process itself is developed to convert almost all precious metals and PGMs in the Doré metal, leaving other elements into the slag fraction. The Doré slag consist of slag formers, such as borax and silica based minerals, but contain also traces of sealing materials. In addition, the Doré slag is rich in metals present in the anode slime, such as Cu, Bi and Sb, which are not converted into the Doré metal. There are only few published applications at the precious metal plants, where conservative grinding and flotation circuits have been utilized for the enrichment of valuable metals present in the Doré slag fraction (Godbehere, P.W., 1983; Segawa, C. and Kusakabe, T., 1996). However, the present study shows an alternative approach for the recovery of metals present in the Doré slag by hydometallurgical approach. The study focus on direct mineral acid (aqua regia) leaching of metals present in the Doré slag. The initial dissolved concentrations of Cu, Bi and Sb from Doré slag in the temperature range of 30-50 °C under oxygen purging with addition of 1 vol-% of H2O2 are presented. Chemical and mineralogical analyses were performed for the raw material, leaching residue, and leaching solutions in order to ascertain the leaching behavior of the metals of Bi, Cu and Sb.

Jan 1, 2018

By J. M. Tourre

Recently, interest in rare earth based oxide powders for electronic applications has risen dramatically. Considerable research has been devoted to the chemical synthesis of these compounds to improve the control of physical and chemical characteristics of the powder. In most cases, a high degree of homogeneity, purity and reproducibility is necessary in order to obtain good application properties. The synthesis parameters can control particle size, surface area, and morphology as well as the degree of homogeneity and application properties. Rhone-Poulenc, a world leader in the production of separated Rare Earth chemicals has developed a flexible process to produce a wide variety of compounds. The different processes for the synthesis of YBa 2Cu 3 O 7 will be discussed and compared to the RP process in term of product quality, cost and flexibility.

Jan 1, 1992

By J. W. Leonard

One of the more obvious phenomena which relate to coke formation is that soft coals of low volatile matter content tend to yield hard or high strength cokes while hard coals of high volatile matter content tend to yield soft or low strength cokes. This observation led researchers of the Coal Research Bureau of West Virginia Univ. to study the possibility of using Hardgrove grindability as a supplemental rank indicator for coking properties. Grindability has been used for many years as a means to measure the resistance of coal to comminution but it has rarely if ever been considered for evaluating coals for carbonization. The coal proper- ties which are measured by grindability are complex, but recent work with the difficult-to-correlate high volatile coals has demonstrated that a 93% correlation exists between grindability and the total petrographic rnicrinites, exinites, and resinites. This work demonstrated that inherent ash had no apparent effect on the grindability of high volatile coals, suggesting that the coal substance is apparently harder than the associated ash. These observations, together with the patented Burstlein process," indicate that the distribution of hard and soft components in the individual high volatile coals and blends of coals may be quantitatively interrelated to coke stability through selected ranges of coal volatile matter. The objective of this progress report is 1) to demonstrate the statistical relationships which exist between coal grindability and the numerous coal petrographic entities and 2) to present the results of initial studies concerning the correlation of the coke physical strength index of stability with coal volatile matter and grindability.

Jan 3, 1964

By D. E. Walsh

The behaviour of gold particles on a spiral was studied using radioactive gold tracers. The method allowed the effect of particle size, particle shape, pulp density, feed rate, and splitter settings to be studied. Although the method has been successfully applied to other gravity concentrators, it was found that reliable results were more difficult to obtain on the spiral. However, these preliminary results show that provided suitable precautions are taken, the technique is capable of providing valuable information that cannot be obtained by conventional studies, and could be used to better optimize spiral performance.

Jan 1, 1992

By D. B. Gawthrop, A. Taylor, G. St. J. Ferrott

"This paper presents data obtained as part of an investigation of the explosive properties of ammonium nitrate. During the course of the work: it was found desirable to investigate the sensitizing action of nitrostarch in mixtures of ammonium nitrate containing low percentages of this material. Data were derived as to the sensitivity to decomposition by heat and the completeness of detonation and,of detonation of straight ammonium nitrate, as compared with ammonium nitrate-nitrostrarch mixtures containing 1 to 10 per cent of nitrostarch.The ammonium nitrate was a sample of coated material obtained from the salvage of amatol shells. Its analysis was as follows:"

Feb 1, 1930

By ERIIL SCHROEDTER

THE death, on May 6, 1908, of Dr. Hermann Wedding, Privy Mining Councilor of the Kingdom of Prussia, and Professor of the Metallurgy of Iron and Steel at the Royal Mining Academy of Berlin, was a loss keenly felt by the whole metallurgical world. Not alone in his native land, but also in foreign countries did he enjoy an esteem of which the title of honorary membership in the American Institute of Mining Engineers, the United States Association of Charcoal Iron-Workers, and the (British) Iron and Steel Institute bears eloquent testimony. Hermann Wedding was born March 9, 1834, in Berlin. At the suggestion of Dr. C. J. B. Karsten, the veteran father of Prussian metallurgy and author of the first German text-book of the metallurgy of iron, lie turned his attention, after gradu¬ating from the gymnasium, to mining and metallurgy. In 1853, he began a practical course at the Malapane iron-works, in Upper Silesia. Subsequently, he studied at the Berlin Mining Academy, and received from the University in 1859 the degree of Doctor of Philosophy. A journey which be made to England, somewhat later, led to his undertaking a German translation, with revision and additions, of John Percy's classic treatise on the metallurgy of iron and steel, the publication of which, in successive installments, stretched through many years. In 1863, lie published, as a thesis in connection with his "Assessor's examination," an essay, entitled The Results of the Bessemer Process for the Production of Steel, and Its Prospects for the Rhenish and Westphalian Iron and Steel Industry, which revealed such ability and knowledge as to secure for him a call to the chair of metallurgy in the Berlin Mining Academy.

Jun 1, 1909

By Osamu Taki

The development of new auger bits for soil cement column drilling equipment has made it possible to create a homogeneous mixture of soil and cement-reagent slurry. As a result, soil-cement columns are used for foundations of houses and buildings, with reliable results, as demonstrated by many field projects and laboratory tests. This paper presents and discusses construction techniques for soil-cement columns, characteristics of the soil-cement solid, quality control, bearing test results, and soil-cement foundation design procedures.

Jan 1, 1992

By David J. Puller

As part of the value engineering process on a major Design Build highway project, instrumented trial pile load tests were used to achieve savings in cost and time on the foundations for a major river crossing. Two trial piles were tested close to failure load at 25MN. Following the interpretation of the pile load test results which included the determination of the ultimate shaft and base capacity, the mobilisation of the shaft and base resistance with pile displacement, and correlations with vertical effective stress and SPT profile, a revised design methodology was proposed. A 25% enhancement on commonly assumed ultimate shaft friction in Chalk was adopted. In addition a significant reduction in the Factor of Safety on end-bearing capacity generally used was also implemented. The revised design resulted in a significant cost and time saving on the piling operation with the pile length reduced by up to 6m (approx. 20%) for the river piers.

Jan 1, 2002

By DONALD E. BARNETT

Since the days of early settlement ew Brunswick has produced a variety of industrial minerals but it is perhaps only the recent discoveries of significant reserves of potash that have elevated the meaning of industrial minerals in their contribution to the provincial economy. With potash production commencing in July 1983, the role of industrial minerals will increase significantly to the value of mineral production in the province.

Jan 1, 1984

By J. Drenda

The model for methane removal from the workings directly behind an advancing longwall as presented in this paper may be used for U-ventilated cross or length-wise systems of longwall advance, starting from the boundaries of the extraction field. In mines with high methane concentrations, Uventilated longwall extraction from the boundary of the extraction field produces a methane risk. The risk is manifested by a higher methane concentration at the end of the longwall, upper gate and incline. The methane in increasing concentrations, which is emitted mainly from the workings with caved areas, appears towards the end of the longwall and in the upper gate. The graphical model of the longwall provided includes both the workspace of the longwall and the caved area. Based upon a model of the rock distribution in the cave, a ventilation model comprising two standard air splits and large number of crosswise air splits has been constructed. Simulations indicate that if the shearer is not present in the longwall, the air distribution in the caved area is symmetrical. The presence of the shearer, both at the bottom and the top of the longwall, causes an asymmetrical air distribution in the cave, that is the asymmetrical flows in the goaf and longwall workspace and in the inflows and outflow between those regions. This phenomenon causes an increase in methane concentration at the end of the wall and at the upper gate. The methane removal method proposed for workings with a caved area directly behind the advancing U-ventilated longwall, starting from the boundary of the field, consists of the removal of methane-air mixtures from the caved area with the boom pipes. These booms may be of several meters long and may be extended if necessary. The insertion of the boom pipes into the cave towards the end of the longwall and connecting them with the general methane removal system creates negative pressure causing a change in the depression field, which is the aerodynamic potential field in the goaf area around the ends of the boom pipes. This will promote the extraction of the methane-air mixture from voids and the goaf cracks, and the area from which methane is being extracted may extend to the side of the cave. This is a positive phenomenon, which could result in the methane flow from the goaf into the airflow in the longwall workspace decreasing or even stopping. A reduction in the methane flow into the longwall workspace with extractions booms will be advantageous for the production continuity. Based on the floor load model for the rocks in the cave and the methane-removal boom load model, the value of the force required to move the boom behind the advancing wall has been calculated. Strength calculations for the pipe were performed using a finite elements method. The analysis results, as well as the comparison of the pipe material effort to the strength parameters of steel, which can serve as piping material (for the assumed load conditions), lead to a belief that the proposed boom construction satisfies the strength requirements.

Aug 1, 2013

By H. W. Kasaini, E. Bourricaudy, T. Larochelle

Rare Element Resources Inc., a U.S. based company, has developed a three-stage process for producing a +98% mixed REO powder from hard rock feedstock (-48 mesh, 2.9-4.8% REO) consisting of bastnaesite and ancylite minerals. Firstly, the whole ore is digested in chloride media at low temperature in counter-current flow mode. Secondly, the rare earths (REEs) are selectively precipitated as oxalates directly from an impure pregnant leach solution (PLS). Finally, significant amounts of free acid and water are recovered from the REE-depleted filtrate and subsequently recycled within the process. Excess heat from the oxalate calcination process is captured and reused in the plant. Due to the low leach temperature (45 ºC) and moderate acid dosage (240-297 kg/t, HCl), rare earth oxides (REOs) are preferentially leached out of fine solids leaving most of the base metals (Ba, Fe, and Al ) in the residue. Selective recovery of REEs from the PLS is achieved by mixing dilute oxalic acid (33% H2C2O4) and PLS at elevated temperature (85-95 ºC). The REEs plus thorium are precipitated as oxalates (REE2 (C2O4).xH2O) while the base metals are left behind in the barren filtrate. Multiple batch and pilot test results have confirmed that 50-80% of the oxalic acid can be recovered from the REE-depleted PLS through low-temperature crystallization (10-15 ºC). Typical leach efficiencies of critical rare earths at 45 ºC range from 85-99% (average 93%) while oxalate precipitation at high temperature increases the crystal size of RE oxalates (>450 microns, d80) thereby improving filtration. The economic benefits of this process include elimination of flotation and magnetic separation Capex and driving hydrometallurgical Opex down to $6- 7/kg, REO produced. As part of a comprehensive risk mitigation strategy, Rare Element Resources Inc has operated multiple pilot plants at SGS in Lakefield, Ontario, Canada to optimize counter-current leaching (CCL), REE oxalate precipitation (OXP), and thorium removal circuits. This paper presents pilot testing data from CCL and REE OXP circuits.

Jan 1, 2016

By I. Serepa, N. C. Steenkamp

Investigations were conducted to determine the condition and stability of the existing decline at amine in the Kalahari Manganese Field, Northern Cape Province, South Africa. During the inspection of the decline, voids were identified behind the concrete lining on the hangingwall and sidewalls over a total linear distance of 230 m. The voids did not provide confinement and, as a result, self-mining was occurring behind the lining. Water was flowing into the decline, over a total linear distance of 100 m, at areas where the decline intersected incompetent rock units, causing softening of the concrete lining and deterioration of the surrounding rock mass. Further damage to the concrete lining was caused by expansion and contraction of the wet red clay unit. Remedial work comprised void filling and water sealing to prevent further deterioration of the decline and ensure that it remained operable for the remainder of the life of mine. Void filling was accomplished by drilling rows of holes along the decline to access the voids and filling the voids with foam. This was followed by the sealing with polymer fluids. Telescopic pipes were also installed to allow water to drain off. A visual inspection was conducted and check-holes were drilled to assess the quality of the remedial work. The void filling material had penetrated cracks in the concrete lining, and areas where voids were intersected by check-holes were re-filled. Additional holes were drilled to re-seal areas that were still wet. The remedial work was completed successfully, as all voids were filled and stability achieved without compromising the concrete lining. The ingress of groundwater was also reduced to some residual dampness.

Mar 2, 2022

By Chao Li, Shuai Wang, Hongxu Li, Lifeng Zhang, Xie Yang

The method of chloride-hypochlorite leaching has the advantages of short process, low pollution and higher in reaction rate compared with the traditional leaching method. In this research, NaCl - NaClO solution is used to leaching gold from a refractory gold concentrate, and the influence of NaCl and NaClO concentration, reaction time to the leaching rate were investigated in this experiment. The raw materials and the leaching residue were characterized by a series of analysis methods such as XRD, XRF, SEM and EDS. Results indicate that the leaching rate and the desulfurization rate can be achieved at 96.26% and 98% with most optimum conditions as follows: NaCl concentration 50g/L, NaClO concentration 200g/L, Liquid-solid ratio 10:1, the best reaction time was 150 mins. And these conditions should be guaranteed pH<8.0, ORP>900mV.

Jan 1, 2015

By Suzie Poulin, N. Geoffroy, G. P. Demopoulos

Most metallurgical industries generate toxic waste that must be treated prior to being released to the environment. However, in a lot of cases, the waste materials are poorly characterized or the analytical results are not well interpreted. These shortcomings often result in the development of inefficient industrial procedures, thus causing economic waste and difficulty meeting environmental regulations. Fortunately, a wide range of analytical techniques are available to guide researchers and engineers into making sound process development decisions. In this work, an industrial selenium and mercury removal process is used as an example to illustrate the application of X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) coupled with Energy-dispersive X-ray spectroscopy (EDX) and powder X-ray diffraction (PXRD) on solid waste. Furthermore, samples of analytical results are presented and interpreted and the modifications to the industrial process that resulted are explained. Finally, a brief description of the advantages and limitations of the aforementioned analytical techniques is given with an emphasis on industrial solid waste material.

Jan 1, 2011

Ore textures in Australian BIF-derived ores are quite complex and have formed the basis for ore genesis models, which includes hypogene upgrading or supergene upgrading then regional metamorphism for the microplaty hematite ores and supergene upgrading for the martite-goethite ores. Despite a high level of ore texture knowledge, little is known about the spatial distribution of ore textures within deposits or their relationship to downstream processing. This paper describes a new iron ore texture classification system to better understand the vertical textural zonation characteristics of Australian BIF-derived deposits, the interpreted role of recent supergene upgrading processes on modifying primary ore textures and their implications for downstream mineral processing. The iron ore textural classification scheme presented uses textural groupings defined on the basis of similarities in mineralogy, ore texture, porosity, mineral associations and hardness. The scheme is non-genetic and has been successfully applied to deposits in the Pilbara, Yilgarn and Gawler cratons. The main ore texture groups include dense martite/hematite, microplaty hematite, microplaty hematite-goethite, martite-goethite, goethite-martite and goethite-rich. Each group can be further subdivided into physically hard to softer subcategories. The ore textural groups can be divided into those interpreted to be associated with primary replacement of BIF and secondary textures resulting from more recent modification by near-surface hydration or dehydration processes. A schematic vertical section through BIF-derived deposits consists (from surface) of detritals underlain by a carapace, both of which may have been eroded, followed by a hydrated zone with replacement of primary ore martite and microplaty hematite by vitreous goethite. The hydrated zone is underlain by 0.2 - 6 m thick zones of intense dehydration and textural infilling of porosity with hematite and hydrohematite. Immediately below the dehydration zone is a strong zone of leaching, where more porous and friable ore textures occur, followed underneath by a gradational contact with primary ore. Secondary supergene processes can impact on beneficiation with hydration and leaching resulting in more difficult density separations at the concentrator stage due to reductions in density differences between ore and gangue and loss of heavy media into pores. Supergene modification of primary BIF-derived ore textures can substantially change lump metallurgical properties, with hydration and dehydration favourably increasing lump yield but reducing resistance to thermal shock whilst leaching will give the opposing outcome. The lump properties of ore textural groups appear to be relatively consistent within and between the iron ore deposits examined.

Jan 1, 2002

PHILIP D. BLOCK, JR., vice president of Inland Steel Co., visualizes a fine future for the Menominee Range of the Upper Peninsula of Michigan. He sees a future unclouded by threat from foreign ore imports or the development of low grade ore processing in Minnesota. The statement was made during the opening of Inland&apos;s new Cayia mine near Crystal Falls. Inland, according to the vice president, is planning to use an increased amount of the high phosphorous ores found on the Menominee Range. He said that other steel companies will probably do the same, because the steel industry has learned how to use ores of high phosphorous content. He said: "I do not mean to imply that we can use an unlimited amount of high phosphorous ores or that we can burden our blast, furnaces with 100 pct high phosphorous ores, but we have reached the point where we can absorb a much larger percentage of these ores without any detrimental effects. Foreign ores and lowgrade Minnesota ores cost too much to offer real competition, Block said. Transportation costs from the Menominee range to steel producing centers in Chicago and on Lake Erie are less than for any other range in this country. In the meantime, the American operators of the Bomi Hills iron ore mine in Liberia, have reportedly signed a new agreement with the Government. Several months ago, President Tubman of Liberia expressed a definite dissatisfaction with the original contract. Informants state that the agreement only needs the approval of the Export-Import Bank, which loaned Liberian Mining Co. $4 million to develop the iron ore properties. Majority stockholder of the Liberian Mining is Republic steel, with 61.57 pct of the stock. Under the new contract, the Liberian Government will start to share in the profits when the indebtedness is liquidated and the return of invested capital accomplished, or April 1, 1957, whichever is earlier. Under the old agreement the Liberian Government received a 5 cent per ton royalty and an additional sum based on the price of pig iron. The royalty rate reached more than 17 cents per ton this year. After debt liquidation the Liberian Government will receive 25 pct of net profits for the first five years; 35 pct for the next ten years; and 50 pct thereafter. Until the Government starts to share in profits it will receive a royalty of $1.50 per ton in U. S. currency, in addition to royalties provided for in the old agreement.

Jan 1, 1952

By M. G. Beukes

"In South Africa most of the large gold mines operate between 1500m and 4500m below surface where reef is accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration. Due to the complexity of the ventilation networks used to ventilate these mines and the potential disastrous consequences associated with underground fires, it is of utmost importance that these mines are managed in such a way that underground fires are prevented. However, if they do occur the fires are managed to firstly prevent the loss of life and secondly protect the infrastructure and viability of the mine. The aim of this paper will be to: • Discuss current SA mining legislation regarding underground fire prevention and control. • Examine these fires from a risk management perspective by means of a bowtie assessment. • List and discuss the major Threats and Consequences as determined by the bowtie assessment. • Discuss the various prevention and consequence controls for deep level underground fires. • Examine how to effectively run an emergency control room. From this, a practical way of designing, implementing and managing an underground fire management system is explored. Lastly, the paper identifies new technology and ways of thinking and how these can be used to combat underground fires. INTRODUCTION The orebodies of South African gold mines are generally narrow tabular structures that vary in thickness between 0.8m and 1.2m with an inclination of between 200 and 700. This, coupled with depths of between 1500m and 4500m, as well as the unpredictable geology, creates unique challenges and significantly impacts on mine designs and mining methods. In general, gold bearing reefs are accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration (Figure 1). Mining is very labour intensive with very limited mechanisation opportunities and this increases the risk to human life if an underground fire occurs. On 16 September 1986, one of the worst mining disasters in SA mining history took place when 177 mineworkers were killed at Kinross Mine. An acetylene tank sparked flames that swept through the mining tunnel igniting plastic covering on the wiring and the flames also set fire to polyurethane foam. The burning plastic combined with polyurethane and the toxic fumes that filled the shafts caused the miners death. This incident was a stark reminder of the serious consequence that underground fires can have on human life as well as the crippling financial and asset impact for the mining companies. Over the past thirty years, the SA mining industry reduced the number of mine fires significantly by replacing normal timber support with fire retardant treated timber, alternative support systems such as backfill and elongate support and many other fire prevention initiatives. Although the number of fire incidents and number of fatalities due to fires does not show a direct correlation because of various factors, the controls put in place against fires has had an impact on the number of fire and explosion fatalities (Figure 2)."

Jan 1, 2019