Search Documents

By Frederick Prime

IN this supplementary list no titles to which an * is prefixed have been seen by the compiler; and he will be most thankful to have any omissions or inaccuracies in the list sent to him to be published as a second supplement in the next volume of the Transactions. The author is indebted to Messrs. Robert Clarke, of Cincinnati ; Thomas Macfarland, of Towanda; Professor F. W. Simouds, of Chapel Hill; and Professor J. J. Stevenson, of New York, for valuable assistance. CEDAR POINT IRON COMPANY, BALTIMORE, July 31st, 1880. ALABAMA. Geological Survey of Alabama. Report of Progress for 1877 and 1878 ; by Eugene A. Smith, State Geologist. Montgomery, 1879. 8vo., 139 pp., and 4 maps.

Jan 1, 1880

By Dairo E. Chaverra, Carlos Argumedo‑Jimenez, Oscar J. Restrepo‑Baena

This paper presents the results obtained by processing a gold and silver telluride mineral concentrate from a mine in Colombia. An acid wash, also known as acidification, was carried out, followed by oxidation with nitric acid as a pretreatment. Cyanidations of the pretreatment residues were carried out and the results were compared with results from cyanidations of base materials. The removal of carbonates in the acidification, a tellurium extraction close to 90% during the pretreatment, and a 30% improvement in the gold recovery compared to the conventional process were achieved.

Nov 8, 2023

By Robert G. Lundguist

REAM is a unique and promising method of rock breaking using high energy, inert projectiles to impart mechanical energy to the rock. This paper describes a demonstration of the application of this new technology to two specific problems in open pit mining: secondary breakage and the scaling of loose material from pit walls. Under previous government contracts, Physics International Company developed the projectile impact method for a large variety of commercial and military rock excavation tasks. A 4 meter (13 foot) diameter by 16.8 meters (55 foot) long tunnel was driven at the Hope Valley Mine in the Sierra Nevada mountains of California in 1972 and 1973. An average of 1100 kg (1 ¼ tons) of a 172 MN/m2 (25,000-psi) granodiorite formation was broken by each of 590 shots used to drive the tunnel.l Based on these results it is estimated that REAM can drive over 60 meters (200 feet) of tunnel per day at about 88 percent of the cost of drilling and blasting. In addition, repeated axial impact by high energy projectiles was used to drill a 0.4 meter (16 inch) diameter horizontal hole in the same granodiorite formation. Each shot advanced the hole an average of 0.2 meter (8 inches).

Jan 1, 1976

By Ernest D. Mast

Noranda's Altonorte custom smelter, located in the 2nd region of Chile, 20 kilometres southeast of the city of Antofagasta, started operations in 1993. Presently, 1150 tonnes per day of new feed are smelted with an 85% sulphur capture. An oxy-fuel reverberatory furnace produces a 48%-55% copper matte that is treated in 13 ft. x 36 ft. (3..96m x 10.97m) Peirce-Smith converters (two hot and one blowing). Up to thirty percent of the new concentrate is smelted via dry concentrate injection into the converters. This paper reviews the development of the concentrate drying and injection system, and oxygen enrichment at Altonorte from start-up in 1995 to the present time. The relationship between oxygen enrichment and concentrate injection is reviewed from a theoretical and practical standpoint. Concentrate injection has improved the smelter's productivity and added flexibility to the operations. Due to the relatively high matte grades and the subsequent short converting times, maintaining consistent operations was difficult at times and the smelter has gone through a learning curve. Plant operating results and experiences are presented on the impact of concentrate injection in relation to: feed treatment, blowing times, revert generation, slag quality and refractory wear.

Jan 1, 1999

By AIME AIME

FEW indeed are the sections of the country where trained or partly trained workers have not already been hired by a war industry plant or will be within the near future. Yet right in the midst of the heavily industrialized East lies the anthracite area, home of a million people, whose productive power has persistently been by-passed either by private industry or by the Government Plant Site Board. The chief reason given for not locating war plants in the area is that it is not within the strategic zone, but in numerous instances elsewhere this rule has been waived. Furthermore, the anthracite region is well protected on all sides by mountains and is at all points more than 100 miles inland. Continued depression in the anthracite industry and a crippling blow dealt by the war emergency to the production of silk and rayon goods, the chief manufacturing activity of the area, have resulted in a heavy migration, particularly of trained young workers, into near-by industrial areas. At least 50,000 people are currently unemployed, with the likelihood of an increase in coming months, and as many families are on relief.

Jan 1, 1942

By J. Dahner

Total milling cost is composed of energy, liner and grinding media costs. In primary high ball load milling, the grinding media play the biggest role in total milling cost. This cost can be drastically reduced by improving the impact condition inside the mill. The impact condition inside the mill is influenced by shell liner design (as well as feed end and discharge design) and the type of discharge. The improvement of the impact condition will result in a significant decrease in grinding media consumption. The softened impact condition allows for better alloy optimization, resulting in a further reduction in grinding media consumption. Optimized liner design can also improve energy consumption as less energy is wasted in the projection of the grinding media. Magotteaux utilizes tools to simulate and show the grinding media trajectories for shell and end liners. This paper will present some practical examples where the media and energy consumption can be or has been reduced by optimizing liner design. Keywords Comminution, grinding, liner design, grinding media wear.

Jan 1, 2011

By H. H. Bleakney

THIS paper presents evidence that in 3 1/2% nickel steel, the published temperature for the Ac1 transformation, l,275°F., represents the completion of that transformation, and that its inception occurs approximately 275°F. lower, at about l,000°F. The formation of austenite within this range, especially at the higher temperatures, and its subsequent decomposition to martensite, results in considerable impairment of the properties of the steel. That the solid solution found to occur below l,275°F. is austenite has been questioned, but the evidence herewith presented, while not decisive, appears to be reasonably convincing. INTRODUCTION The February, 1939, issue of Metals Technology contains a very interesting paper by I. N. Zavarine, Associate Professor of Metallurgical Engineering at the Massachusetts Institute of Technology. In that paper, Professor Zavarine presented photomicrographs illustrative of the microstructures produced by heating nickel steels to a temperature slightly below the carbon change point, and holding them at that temperature for various lengths of time. His illustrations show that the structures found after such treatment do not consist merely of ferrite and carbides, but are characterized by the presence of a third phase, which he describes as a' 'sub-critical solid solution'. The occurrence of this third phase in increasing amounts is accompanied by an increase in strength and a loss of ductility and impairment of elastic ratio of the steel. Some years ago, one of the authors encountered the above-mentioned phenomenon in treating large forgings of 3.5% nickel steel. After normalizing and then drawing at l,250°F., very poor mechanical properties were obtained. Investigation of the steel disclosed no inferiority in quality. Eventually, after considerable waste of time and money, a draw temperature of l,150°F. was tried. This treatment resulted in a very great increase in elastic ratio, over 5 per cent increase in percentage elongation, and proportionate improvement in reduction of area.

Jan 1, 1941

By Tom Ireland, Tony Rock

The proposed 1.83km long twin bore A3 Hindhead road tunnel planned for contruction in 2008 is being delivered under a Highways Agency Early Contractor Involvement (ECI) contract. The proposed construction methodology is progressive mechanical excavation of a horseshoe shaped tunnel with shotcrete installed close behind the face using robotic spraying equipment. The tunneling medium is a ‘soft rock’ sandstone for which there was little previous tunneling experience, requiring extensive geotechnical investigations and an innovative approach to lining design. A 240m long portal section though sandy material utilising a steel pipe umbrella is also required. This paper describes the development of the tunnel planning and design including the most recent developments in UK road tunnels, and the innovation included in the ‘permanent’ primary lining design.

Jan 1, 2007

By T. K. Kim

Iron, cobalt, and nickel in waste ferric chloride solutions were separated from each other by solvent extraction. The iron was extracted from the cobalt and nickel by the use of methyl isobutyl ketone, and then the cobalt was separated from the nickel by the use of a high-molecular-weight quaternary amine dissolved in a solvent of high aromatic content.

Jan 1, 1980

By PW Meisel

An hydraulic-powered reel system to minimize peak tension transients in shuttle car trailing cables has been theoretically designed and analyzed using a computer. A single spring-loaded take-up sheave stores or gives up cable to maintain tension within specified limits. Controls have been incorporated to shut down the vehicle before all cable is removed from the reel and to de-energize the cable in the event of a reel/cable jam. Full-scale hardware configuration drawings sufficient for manufacture of a test system have been completed.

Jan 1, 1983

By Russell G. Haworth

Three companies, United States Potash Company, Potash Company of America, and International Minerals and Chemical Corporation, are now operating potash mines and refineries in the Carlsbad, New Mexico, area. The three mines are located approximately twenty miles east of Carlsbad. The deposits have been found ideal for mechanized mining methods. This summary has been compiled from information made available by the three operating companies.

Jan 1, 1949

By L. R. Shoenberger

Boron has been used to produce nonaging low-carbon sheet steel. Retention of the necessary minimum amount of about 0.006 pet partially killed the steel. Amounts exceeding about 0.012 pet increased the degree of deoxidotion, piping tendencies, and possibility of hot tearing in primary rolling. Semikilled practice resulted in good ingot yields and satisfactory surface quality. Aluminum added with the boron provided a protective de-oxidizer. Good drawobility was indicated by performances of the steel in a limited number of deep-drawing trials. Some problems with hot-tearing and boron-analysis procedures were overcome. Metal lographically, the boron semikilled steels revealed some structures not usually found in plain low-carbon steels. IN 1943 Low and Gensamer1 reported that strain aging, which hardens and embrittles ordinary low-carbon rimmed steel, was due to nitrogen and carbon, and that oxygen played a relatively unimportant role. Since then, many investigators have substantiated their findings and indicated that nitrogen is particularly potent. Commercially, today's most widely produced non-aging sheet steels for deep drawing are either aluminum killed or vanadium rimmed types. The difference in deoxidation practice, alone, is evidence that oxygen is apparently not an important consideration in control of strain aging. The fact that nitrogen is important is apparent in the consideration that has been given, knowingly or unknowingly, to the amount combined with aluminum and vanadium. Patents were granted to Hayes and Griffis2 for the processing of aluminum-killed steel, and to Epstein" for the manufacture of vanadium rimmed material. Certain prescribed steps in producing these steels can be correlated with the formation of the respective nitrides within certain temperature ranges below the usual hot-finishing temperatures. The potential nonaging properties of either type can be reduced or suppressed by cooling too rapidly to permit the aluminum or vanadium to combine with nitrogen. Subsequent suberitical annealing of the cold-rolled strip, however, normally forms the nitrides and produces the resistance to strain aging. Titanium-killed nonaging steel, described by Comstock,1 forms a nitride in the molten state and is essentially nonaging throughout its processing. Zirconium-killed steel, which was investigated briefly by the author,* appeared to have similar nitride- forming characteristics. It is known" that chromium can produce nonaging rimmed steel, but relatively little is known of the potentialities of some of the other nitride-forming elements such as boron, silicon, columbium, and cerium. In attempting to develop a new nonaging cold-rolled sheet steel with good drawability, the following factors were considered pertinent. Such a steel would necessarily have a low carbon content and therefore have a relatively high degree of oxidation when made in a basic open-hearth furnace. If the denitriding element were also a deoxidizer, a part of the addition would be lost as oxide. The degree of deoxidation would determine whether the steel is rimmed, semikilled or killed, and also could be expected to have an important bearing on ingot yields and ultimate surface quality. Assuming that the pattern for the production of cold-rolled sheets would not be changed to any great extent, the nitride must form in the molten steel, in hot rolling, in subsequent cooling, or in annealing. The nitride, once formed, should resist dissociation and be stable in the final product. Usually an excess of the nitride-forming element is required to combine with sufficient nitrogen. If the element used is a strong ferrite strengthener, a small excess may markedly decrease drawability. With aluminum and vanadium, about 0.03 to 0.05 pct in the steel is preferred. Epstein has said" that about 0.30 pct chromium is required. Titanium nonaging steels are hard unless a sufficient amount (about 0.30 pct) is added also to combine with the carbon. The cost of the necessary amounts of these latter two elements discourages commercial acceptance. Silicon was considered as a possible nitride former, but since amounts up to 0.10 pct in rimmed and semikilled steels do not induce marked resistance to strain aging, larger amounts are apparently required, which would tend to harden and strengthen the ferrite. Of the other elements mentioned, all but boron are expensive heavy-metal elements. Stoichi-ometrically, almost an equal weight of boron would be required to combine with the nitrogen—-ordinarily about 0.003 to 0.006 pct in scrap-practice open-hearth steels. Boron is a slightly stronger deoxidizer than carbon but is less powerful than zirconium, aluminum, or titanium. Thus a rimmed-steel practice might be possible. There is much in the technical literature concerning the hardenability effects of minute amounts of boron in killed steels but very little about its behavior in low-carbon material—particularly as a ferrite strengthener. The available data indicated a need for better information concerning the effects of boron in low-carbon strip steels. Experimental Work Development of a Boron-Treated Nonaging Strip Steel—Initial attempts to produce a boron-rimmed strip steel employed 3-ton basic open-hearth heats which could be teemed into molds large enough to sustain a normal rimming action. Boron as ferro-boron was added to the ladle in small amounts because of the reported hot-short character of aluminum-killed heat-treating grades containing more than about 0.005 pct boron. Actually, the amounts used, i.e., 1/8 and 1/4 lb per ton, would be large for

Jan 1, 1959

By H. Beecher Charmbury

Water is a most remarkable substance. It is essential for life of all kinds. Not only can no one live without water, but man has always needed water for farming, raising animals, manufacturing, transportation, and recreation. When our country was young and inhabited by few people, the streams, rivers, and lakes were able to provide all the clean water needed by man and take away all the wastes created by man. However, with our growing population and our ever-increasing demand for goods and services, the public, industry, and government at all levels have become aware of the need to more efficiently manage the water resources of this nation. Coal has helped this nation to become the greatest industrial nation in the world. Coal has generated our electricity, run our railroads, and helped arm our nation during wartime. The result has been the highest standard of living in the world, a time of widespread prosperity, and a national defense potential that has delivered the hardware during four wars in this century. The use of water in coal mining is somewhat different than in most industries. With the exception of the small amount of water used in cleaning plants and for fire protection, most of the water encountered in coal mining operations is unwanted since it serves no useful purpose. In other words, it must be removed, otherwise it will interfere with mining operations by flooding. In the past, removing water from working areas of most mines was usually a fairly simple matter. Pumps with piping were installed at sumps or low spots in the mine and the water was pumped to the surface. Ditches were often used to drain the water by gravity to the outside or to main sumps for pump discharge. In either case, the water was allowed to flow into the nearest stream or river. The concept of "water is water" was generally accepted without too much concern over what

Jan 1, 1973

By Roney Eduardo Lino

Melhorar a qualidade dos aços e dos processos tem sido uma rotina dos engenheiros metalurgistas e das siderúrgicas em um mercado que exige produtos com qualidade e preço competitivos. No processo de refino dos aços são feitos os ajustes de composição química e temperatura, além das modificações inclusionárias necessárias às características de qualidade dos produtos e as exigências para uma perfeita lingotabilidade. O processo de solidificação mais comum é o lingotamento contínuo, onde a continuidade de fluxo de aço líquido através das válvulas é assegurada através da temperatura adequada e presença de inclusões no estado líquido nas temperaturas de lingotamento. Neste trabalho foram utilizados os softwares Thermocalc e CEQCSI com o objetivo de avaliar o efeito dos elementos químicos carbono, silício e enxofre na janela de lingotabilidade de diagramas de fases alumínio vs cálcio. Os softwares se mostraram bastante apropriados e eficazes neste estudo, e os resultados indicam que os elementos estudados afetam diretamente a posição da janela de lingotabilidade dos aços carbono. A análise de amostra de tarugo de um aço 0,2%C via MEV mostrou que há grande heterogenidade de inclusões no aço acalmado ao alumínio e tratado com cálcio.

Aug 8, 2018

By Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

The possibility to develop an efficient recovery and reuse of concrete materials from Demolition Waste (DW) represents one of the main targets applied to end-of-life constructions dismantling/recycling. The need to recycle end-of life concrete materials is strongly increasing in these last years for several reasons: i) the decrease of steady supplies of good quality natural aggregates, ii) the need to secure ample supplies of concrete aggregates to the construction industry and, finally, iii) the environmental constraints limiting the DW wastes disposal. The fulfilment of these goals produces several benefits, that is: i) a reduction of new resources consumption, ii) a strong reduction of the costs linked to transport and energy production, iii) the possibility to utilize materials, otherwise lost (e.g. land filled), iv) land preservation and, finally, v) the reduction of the environmental impact of new exploitation activities. A lot of efforts have been addressed to develop, set-up and apply innovative technologies to maximize DW conversion into useful secondary raw materials. The possibility to utilize efficient, reliable and low cost analytical tools to perform detection/control actions: i) to assess concrete characteristics, before demolition, and ii) to detect the presence of contaminants in coarse aggregates (e.g. bricks, gypsum, steel, glass, plastics, wood, etc.) represent the key issues to fulfil in order to develop innovative process/control actions/procedures inside the DW sector. In this paper a new technology, based on HyperSpectral Imaging (HSI) sensors is investigated to develop suitable and low cost strategies finalised to define and implement innovative smart detection engines for sorting and/or DW flow stream quality control, addressed to perform recovered materials and/or products certification. The proposed sensing architecture is fast, accurate, affordable and it can strongly contribute to bring down the economic threshold above which recycling is cost efficient.

Jan 1, 2014

By G. Ward Wilson

Waste rock and tailings may be combined through intimate blending to create new materials with superior physical and hydraulic properties. The new material, termed Co-Mix, has high shear strength characteristics, low compressibility, low hydraulic conductivity, and a high water retaining capacity. Co-Mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures and full depth waste repositories. Field scale test trials using Co-Mixed blends of waste rock, tailings and slag have been constructed at the Copper Cliff Mine in Sudbury, Canad. These lysimeters will be used to evaluate the performance of the new material for cover systems that may potentially be constructed on the tailings impoundment upon closure. In this sense, the paper point out the construction of the lysimeters with respect to expected field performance during the spring snow melt period and summer to produce cover systems for closure.

Sep 12, 2005

With the employment of a system of ore pillars to support the hanging wall during the mining operations at the North Mine, it was found that, when the stopes were worked out and the pillars remained intact, the main footwall drives developed an undulating longitudinal section due to the shrinkage of the filling in the worked out stopes.These depressions collected water, which made the footwall drives very wet under foot, and everitually worked its way into the pillar workings and the levels below.Water was also finding its way into the shafts because of the silting-up of the level drainage systems and, as both the shafts are down-cast, this tended to increase the humidity of the air entering the mine.To overcome these troubles it was decided to try a system of siphons as a method of subsidiary drainage.SYSTEM AT PRESENT IN USE.All drainage water is collected as near to its source as possible, run into a sump in an adjacent low lying part of the level, and continuously removed from these sumps by a siphon system.Each level has its own system. Water is collected from the sumps by a 1-in. pipe and delivered to a pipe running the length of the level along the back of the footwall drive. At the shaft the pipe is increased to...

Jan 1, 1938

By GEORGE A. KIERSCH

The awesome destructive power of known and projected weapons of war presages a new need for geologists and engineers, who may be called upon to locate vital industry underground, thereby protecting it from sky-borne destruction. The Corps of Engineers is now conducting special tests to establish design standards covering the general field of underground installations as well as surveys a of construction methods and the operational hazards connected with such plants. National planning must dictate a policy that is either tactical, where surface manufactured parts; are stored underground and during art emergency assembled, or operational with both the manufacturing and assemblage completed in subsurface plants. Both plans of operation require the use of subterranean plants. Relocation of vital plants underground will probably involve only a small percentage of the production capacity of this nation. The cost of rebuilding in new location will obviously limit its adoption

Jan 1, 1949

By S. Mathur

Oxide particles are commonly used as fillers in plastics, paper, rubber etc. (particulate composites). The successful fabrication of such composites is dependent upon the adhesive strength of the filler particles to the matrix. The compatibility of the matrix and the filler particles is generally enhanced by adsorption of surface modifiers such as surfactants and polymers at the particle-matrix interface. In order to develop a scientific basis for selection of appropriate modifiers it is necessary to understand their adsorption mechanism(s). Specifically, adsorption of polymeric additives is attributed to a combination of chemical and electrostatic interactions, hydrogen bonding and van der Waals forces. Hydrogen bonding has been suggested to be the primary adsorption mechanism for non-ionic polymers. However, a literature survey of Poly(ethylene oxide)(PEO)-oxide system suggested PEO, a non-ionic polymer, to be substrate specific. A systematic study was undertaken to investigate the adsorption mechanism(s) of a PEO on oxide particles. It was determined that strong Bronsted acid sites on the surface interact with the ether oxygen, a Lewis base, of PEO to induce adsorption. In this work characterization of PEO binding sites on oxides is reported and the mechanism(s) of PEO adsorption discussed.

Jan 1, 1997

By Wei Luo, Yuanbo Zhang, Zhixiong You, Zijian Su, Guanghui Li, Tao Jiang

"In this study, the appropriate sintering process parameters for low-grade ferromanganese ores were investigated. The results showed that, under the condition of natural basicity (R=0.03), the optimal parameters were obtained as follows: moisture of mixture 9 .1 %, coke powder 9 .9% and sintering negative pressure 7 KPa. And the corresponding yield, ISO tumbling index and utilization coefficient reached at 80.18%, 61.27% and 1.515t·m-2·h-1, respectively. Under the optimal parameters, the emission of harmful gases, such as S02 and NOx, were reduced evidently with 30% of coke powder replaced by biomass charcoal. Moreover, it was found that the basicity had obvious effects on the quality of the sinters when it changed between 0.03 and 2.4. The ISO tumbling index gradually decreased from 61.27% to 55.47% with the basicity increasing from 0.03 to 1.2, then, it began to increase after the basicity further increased to 2.4.IntroductionManganese is mainly consumed by steel and battery industries, particularly in the steel plants and ferroalloy units. The consumption of metal manganese in the ferroalloy industry accounts for 85%-90% of the total Mn [1-2]. Therefore, ensuring sufficient manganese alloys is essential to meet the rapid development of steel industry. Recently, rich-manganese slag containing high grade Mn (>40%), low Fe (1%) and P (<0.03%) is considered as superior raw materials for manganese alloys. While the sinters made from manganese ores are major raw materials for producing rich-manganese slag with the increasing exhaustion of natural rich manganese lump ores [3-5]."

Jan 1, 2013