Search Documents

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By S. Uddin

An integrated device has been developed to measure sedimentation potential, conductivity and pH simultaneously of particulate systems. Maxwell?s model was used to calculate volume fraction of solid from the conductivity data. In this approach, all system variables are known and zeta potential can be calculated from Smoluchowski?s equation. The technique is validated by comparing zeta potential vs. pH for alumina and silica suspensions with electrophoresis measurements. The technique was extended to mixed alumina/silica systems. Sufficient column height along with size difference between the two minerals allowed gravity fractionation during settling. Sedimentation potential measured over time identified the transition from one mineral to the next. Using XRD analysis the results supported the correlation between surface charge and sample composition. This is a step towards characterizing surface charge of mixed systems of interest in mineral processing.

Jan 1, 2010

By Vadim J. Jabotinski

This paper describes several areas of application for electron beam processing of materials. The technology and use of electron beam systems in gas phase synthesis reactions are described. Gas phase reactions may be used to generate ultra- fine metal or ceramic powder that are very pure and crystalline. Among the examples presented are: the generation of nanometer sized metal powders and the gas phase synthesis of silicon carbide for silica and methane. The experimental system is described and future theoretical and experimental objectives are identified.

Jan 1, 1998

By I Ritchie, G Lane, C Morley, D Yataco

Marcobre SAC (Marcobre) is developing the Mina Justa project in Peru. The project has a lower grade oxide orebody overlaying the higher grade sulfide orebody. The oxide ore is treated by acid leaching; consumption of acid is high and is managed by vat leaching rather than the more conventional heap leaching process.The leaching process uses ore crushed to 100% passing 8 mm to optimise copper recovery. Acid consumption generally increases with a higher proportion of fines. Marcobre is investigating a three-stage crushing circuit with high pressure grinding rolls (HPGR) in the third stage, instead of the more conventional four-stage cone crushing circuit. The use of HPGR can result in higher fines production due to the higher compression forces in the crushing zone. This paper reports on the outcomes of the test work completed by Marcobre in 2016 and 2017 to manage fines production and compare the use of HPGR with conventional crushing on a high acid consuming ore.At moderate pressing forces, a HPGR crushing circuit appeared to produce similar size distributions to cone crushing. On average, both the copper recovery and the acid consumption in subsequent vat leaching were higher with HPGR crushing than with cone crushing.CITATION:Lane, G, Morley, C, Yataco, D and Ritchie, I, 2017. Are there differences in size distribution when comparing conventional crushing and HPGR?, in Proceedings MetPlant 2017, pp 60–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By N. J. Grant, E. Gregory

The creep rupture properties of wrought aluminum powder products made from five grades of sintered aluminum powder were investigated at temperatures from 400° to 900°F for rupture times up to 1000 hr. The effect of stress concentrations on materials of this type was investigated by means of notched creep rupture tests. A tentative correlation was obtained between the creep rupture properties and the structure as revealed by electron micrographs. SEVERAL papers have been published recently concerning the production and properties of wrought aluminum powder products and their possible high temperature applications. Most of the published work in this field has come from abroad, notably Switzerland, and articles by Irmann and his colleagues were summarized in English recently.'.' Most of the papers published by Dr. Irmann are principally concerned with the retention of properties (by a product which is produced from extremely fine flake powder and is subsequently hot extruded) after heating to high temperature for prolonged times. The powder may be in atomized or flake form, and during hot working the applied pressure is reported to plastically deform the aluminum powder, thus breaking the oxide skin and welding the particles together. Irmann attributes the remarkable properties to the dispersion of oxide inclusions. Specifically, the product described by Irmann is one labeled SAP (Sintered Aluminum Powder) in which the initial flake powder is so fine that at least 50 pct of the flakes have one dimension of 2 microns or less. The composition of the starting aluminum shows in percent, Fe, 0.18; Si, 0.19; Zn, 0.06; Ti, 0.03; Cu, Mn, Mg, all nil; balance Al, approximately 99.5 pct. Aluminum is not the only material that has been found to have increased resistance to deformation at elevated temperatures when produced by powder metallurgy. It has been reported by Middleton, Pf eil, and Rhodes- hat platinum has a higher recrys-tallization temperature when produced by powder metallurgy and exhibits peculiar properties, many of which are similar to those of the aluminum powder products. Difficulties were encountered in explaining the reason for the strengthening in the case of platinum since the existence of the oxide is doubtful. The authors attributed the special properties to "a small amount of suitably dispersed porosity." This theory was supported by von -~eer-leder4 in the discussion to the paper, and the similarity between this method of hardening and that suggested by Rohner in his theory of age hardening was pointed out. R. de Fleury5 attempted to explain some of the properties in terms of the modulus of elasticity and elastic limit of alumina and aluminum while von Zeerleder examined the relationship between the yield strength and the reciprocal of the powder particle size. Boenisch and WiderholtQ dealt mainly with the corrosion resistance of the powder aluminum material and compared it with other aluminum alloys. The diffusion rates of other metals in SAP and pure aluminum have been compared by Seith and Lop-mann.' They showed that the alloying metals diffuse particularly quickly in SAP possibly due to the very fine grain size. The properties of the Alcoa products were given by Lyle.' The creep rupture properties of SAP and two of the Alcoa experimental powder products were compared by Gregory and Grant hnd it was shown that these products are vastly stronger at 900°F than are the best cast and wrought alloys at 600°F. Since the publication of these data, the authors have investigated two further aluminum powder products and it is the object of this paper to show how the high temperature creep rupture properties of the five materials vary with oxide content and with the structure as revealed by electron microscopy. Materials One of the five products, SAP, a sintered aluminum product, was supplied by the Societe Anonyme pourl Industrie de l,Aluminium, Neuhausen a/RHF, Switzerland, through Dr. R. Irmann, while the others, M276, M257, M293, and M255 were supplied by the Aluminum Company of America as experimental powder metallurgical products. M255- and M293 were made from coarse and fine atomized powders, respectively. The other materials were made from flake powders with significant differences in oxide content, the details of the type of powders used in the manufacture of these materials

Jan 1, 1955

By D. J. Charlton

"IntroductionMaintenance is a business, which to be successful, requires good management, systems and reporting. The prime objective of the maintenance management group, be they large or small, must be to anticipate and prevent interruptions in operations by keeping equipment in good mechanical condition. This objective should be carried out at minimum cost consistent with maximum productiveness.The objective of this chapter is to give an insight into the various aspects of maintenance management that must be considered to effectively and efficiently operate a mill complex. The degree to which the maintenance sub-systems are developed in an operating mill will be determined by the size of the mill and the needs of the operation.The criterion of the management system used is that the system serve the operation and not vice versa. The systems presented should be considered as tools and, as with all tools, they must be sharpened and replaced as the need arises or as more effective tools become available.To understand what is involved in maintenance management, it is worthwhile to consider a systems approach to analyzing management problems. This approach was developed by J.A.B. Rae while reviewing maintenance management systems for Cominco Ltd.A very simple system involving managing results and objectives is shown diagrammatically in Figure 1.The systems approach to organizational development involves four basic elements: an objective, a result, an activity and feedback. In the analysis, the activity element is broken down into individual actions that people could be held responsible for. If we introduce the action of operating into the diagram of Figure l, we arrive diagrammatically in Figure 2."

Jan 1, 1989

By E. O. Stensholt

The Hybinette electrorefining process for production of cathode nickel was in use at Falconbridge Nikkelverk A/S, Norway, until 1975 when conversion to the new chlorine leach process was started. In 1978 the conversion to electrowinning had been completed, but further major improvements to the process have been made up to 1987. After a major expansion program in 1985 - 87 the refinery has a nickel capacity of 54 000 mt Ni/year. The main feed materials to the process are converter matte from the Falconbridge smelter in Sudbury, Ontario, Canada, and from the BCL smelter in Selebi-Phikwe, Botswana. A typical composition of the mixed feed to the refinery is: 40 - 45% Ni, 25 - 30% Cu, 20 - 22% S, 2 - 3% Fe and 1.0 - 1.5% Co. The matte is chlorine-leached in the first process step, nickel being dissolved selectively in a train of leach-cementation tanks. Essentially all copper and sulphur that was present in matte appears in the leach residue as CuS. In 1986 an autoclave treatment stage was added to the process to improve nickel extraction from the leach residue. The resulting strong nickel chloride solution is purified by the process steps (1) precipitation of iron and arsenic, (2) solvent extraction of cobalt and other minor elements and (3) precipitation of lead and the remaining impurities. The nickel solution is then fed to the tankhouse, where various nickel products are produced by electrowinning. The chlorine gas that is produced during the electrolysis is returned directly to the chlorine leaching tanks to dissolve more matte. After stripping from the loaded organic phase and solution purification cobalt is also produced by electrowinning. The copper sulphide leach residue, which contains some nickel, is dead- roasted in fluidized-bed roasters. The sulphur is recovered and sold as sulphuric acid. The calcine is leached in spent copper electrolyte, from which cathode copper is produced by electrowinning. Precious metals and the remaining base metals are recovered from the copper leach residue. The Falconbridge chlorine process is very versatile. It can accept a wide range of impurities in the feed and still produce metals of exceptional purity.

Jan 1, 1988

By Victor V. Nazimko

Multiple mining generates gob-interaction displacements. They redistribute stress m strata and obey laws of irreversibility thermodynamics. An irreversible state causes inhomogeneity of the stress distribution on the mass. A destressed zone develops along a working panel, and worked out panels are deprived of the destressing. The inhomogeneity is smoothed out during elapsed time.

Jan 1, 1996

By E N. Sparg, O D. A Deuchar, F Needham

Decline shafts are an attractive option to both new and existing mining operations where there is a need to access an inclined orebody deposit via on-reef development so as to generate a return in the shortest possible time. There are many different technologies that are available to transport men, material and rock in incline shafts. This paper focuses on the applicability of two hoisting technologies for decline shafts, namely endless and direct rope systems. The pros and cons of each system are reviewed. A common concern with direct rope haulage systems is the possibility of generating slack rope during deceleration. This paper illustrates the issues involved in designing a system so as to avoid the possibility of slack rope. In conclusion, the key factors relevant to the selection of endless or direct rope haulages for a particular decline application are reviewed. The paper is a joint submission by FFE Minerals-Vecor and Qualter Hall UK.

Jan 1, 2005

By Jerry Dollinger, Levent Ozdemir

An extensive series of laboratory cutting tests using linear and rotary cutting machines were carried out with the objective of investigating the feasibility of achieving very high rates of penetration with TBMs in rocks of low to medium strength. These tests were performed with large diameter disc cuttrs at cutter path spacings and penetrations of up to 12 and 1.75 inches, respectively. A predictor model was also formulated to characterize rock cutting at large spacings and penetrations.

Jan 1, 1987

By Herbert Cremer

The United States,-the largest nickel consumer in the world, produces virtually no nickel from domestic ores. Dependence upon outside nickel - sources and increasing strategic, importance of nickel focused the attention of the United States on deposits within its boundries. The most likely domestic sources of nickel are low-grade oxide and silicate deposits, such as the Cle Clum deposit, Kittitas County, Wash., and the Riddle deposit, Douglas County, Oreg. The Federal Bureau of Mines, Northwest Electrodevelopment Laboratory, Albany, Oreg. has been investigating electric smelting of low-grade oxide and silicate nickel ores. These smelting studies have been on selective reduction to produce low-carbon ferronickel. Selective reduction is based upon the relative reducibility of: nickel, iron, and chromium, in the order named, when the charge contains insufficient carbon or other reductants to reduce the entire quantity of these metals present in the ore.

Jan 1, 1954

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 µm. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By Arno C. Fieldner

Forty years have elapsed since the Bureau of Mines was established on July 1, 1910, by Act of Congress. The convocation of this Sixth International Conference of Safety in Mines Research Directors, 24 days after our 40th birthday, seems to be an appropriate time for reviewing our contributions to mine safety research and the problems yet to be solved from the American point of view. Actually research on safety in coal mines was started by the United States Government in the Technologic Branch of the U. S. Geological Survey of the Department of the Interior in 1908, as a result of a succession of disastrous coal mine explosions in which many lives were lost. In 1910 this work was transferred to the newly created Bureau of Mines. 394 lives were lost annually per 100,000 men employed in the coal mines of the United States in the 5-year period ended in 1910, as compared to 203 lives lost annually in the 5-year period ended with 1949. In 1908 no safe, permissible types of explosives and no certified permissible equipment of any kind were used in American coal mines. Black powder was in universal use and open oil or acetylene lights were common in all but mines known to be gassy. Rock dusting was not practiced to limit propagation of explosions, nor was ventilation in many mines adequate, Our safety practice lagged behind that of foreign coal- mining countries and therefore one of the first steps in carrying out the Congressional Authorization of 1908 to investigate the causes of mine explosions was to obtain assistance from the leaders of mine safety research in foreign countries. At the request of Dr. Joseph H. Holmes, director of the Technologic Branch of the Geological Survey, James R. Garfield, Secretary of the Interior, obtained the cooperation of the Governments of England, Belgium and Germany in sending Captain Arthur Desborough, Inspector of Explosives in England, Mr. Victor Watteyne, Inspector-General of Mines in Belgium, and Mr. Carl Meissner, Counselor for Mines in Germany, to visit American mines and make recommendations for increasing safety and efficiency in mining coal in the United States.

Jun 1, 1950

By Arpana P. Sabu, Themis Vaxevanis, Sissy Nikolaou, Guillermo Diaz-Fanas

Geo-failures from extreme events (landslides, wild fires, earthquakes, floods, etc.) have increased exponentially in recent years around the world and within the USA. When catastrophic failures occur, they usually involve hundreds of fatalities especially in cases of unexpected triggering events, such as large intensity earthquakes or heavy flash floods. Protective actions against identified potential geohazards can mitigate the associated risks and the future occurrences and prevent these occurrences from becoming disasters, targeting the essence of resilience in geotechnical engineering. Imaging and other virtual design and construction tools can be used to identify weaknesses that trigger geohazards and can, in combination with numerical simulations, guide decision making. In spatially distributed problems, 3D visualization and LiDAR-type of technologies are essential in providing geotechnical engineers a deeper understanding of precarious soil zones and support finding appropriate solutions. This paper will present the value of using virtual design and construction technologies though the case study of the Iztapalapa suburb of Mexico, about 20 km southeast of Mexico City. Iztapalapa was developed within irregular topography and has a long history of severe soil subsidence. Following the 2017 Puebla-Morelos earthquake, the town experienced large settlements resulting in extensive damage to the already frail buildings and unregulated infrastructure. The soil subsidence was visualized by mapping available historic and geotechnical data. The visualization helped to identify areas where additional investigations were needed. Additionally, this paper presents a case study of a series of landslides from the 2016 Mw7.8 Muisne Ecuador Earthquake, which demonstrates the advantages of using novel technologies to collect data and create cloud datasets from drones and digital photos to understand and evaluate geo-vulnerabilities in anticipation of an extreme event and during rapid reconnaissance to plan for long-term instrumentation, which can enhance geo-disaster prevention and overall community resilience. INTRODUCTION Iztapalapa is a southeastern borough of Mexico City (CDMX) located within the Mexico Basin (Figure 1). This borough is a densely populated area of CDMX with a total of 1.8 million inhabitants, and has a third of its population living in poverty (Gonzalez-Hernandez et al., 2015) with limited to no access to clean drinking water. Iztapalapa also suffers from high rates of crime, drug trafficking, sex trade and illegal buildings. As the population continues to grow, the already non-regulated and fatigued infrastructure is unable to meet the community needs, especially during and after natural hazard occurrences. The region of CDMX is one of the world’s most seismically active regions that is also exposed to other geo-hazards such as floods, volcanic eruptions, and continuous settlement due to water pumping that has reached 11 meters over the past 100 years (Nikolaou et al, 2019). While the soil subsidence alone has caused significant infrastructure damage in Iztapalapa and throughout the rest of the city, recent earthquakes have also contributed to those damages.

Jan 1, 2019

By O. Mejia

"As study was undertaken to investigate the relationship between mill liner wear and grinding energy efficiency and to assess the opportunity to control mill speed to improve energy performance as mill liner wears. The study involved analysis of plant operating data and liner wear profiles over time. The operating work index was found to be an effective tool to identify the decrease of grinding efficiency along the liner service. The plant data show that the mill grinding efficiency as determined by monitoring the operating work index, and throughput decreases as liner wears. However, efficiency and throughput can be maintained by either changing the liner more frequently or by increasing the mill speed. Two scenarios for increasing mill throughput were analyzed. The first one involves changing the liner before the efficiency drops and the second one requires increasing the mill speed from 75% to 79%. Both scenarios show financial benefits that can be used in mill operations.INTRODUCTION The analysis of the mill power draw is used in this study as a key parameter for comparing mill liner profile and its effect on mill performance. Current technology and simulation software used in the mining industry do not factor in the impact of liner wear profiles in grinding efficiency and mill throughput (Toor, 2013). To address this gap, this study provides an analysis of key factors affecting mill throughput and grinding efficiency: mill speed, ball loading, and liner profiles. Several years of plant mill operating data, published research papers, and MillTraj® simulation results are used to demonstrate that face angles impact grinding efficiency and throughput and that mill speed can be used to overcome this problem. Moreover, the liner profile wear analyses clarify a mismatch between actual and estimated power draw calculations."

Jan 1, 2019

By Ronald F. Balazik

This Bureau of Mines study identifies and examines the costs of Federal, State, and local environmental protection controls on domestic phosphate rock mining, The costs include the expenditures needed to comply with government regulations and the effects that these expenditures and regulations have on supply. The study analyzes costs of environmental impact assessments, air and water quality standards, reclamation laws, potential solid waste controls, and local government restrictions. In addition, an industry survey and the Bureau&apos;s Minerals Availability System (MAS) are used to evaluate land management policies that restrict access to phosphate resources, Conclusions drawn from these analyses confirm that (1) domestic phosphate mining has incurred substantial control costs and may be subject to significant new regulatory costs in the next several years, (2) certain environmental controls can discourage mining investment, (3) environmental policies governing land-use controls affect the disposition of sizable phosphate resources, and are key determinants in the development of those resources on the Federal do- main, and (4) environmental costs could diminish the competitiveness of domestic producers.

Jan 1, 1983

By Yufeng Guo

Mineralogy and physico-chemical characteristics of a nickel hydrometallurgical residue and recovery of iron-bearing minerals by flocculation-magnetic separation were studied. The results show that the nickel residue is super-fine and fraction less than 0.045mm reaches 85.4%. Ferrous minerals are chiefly magnetite and ferruginous glass. Magnetite accounts for 31.7% and exists as free magnetite. Ferruginous glass is of multicomponent amorphous substances with low-iron grade but strong magnetism, and accounts for 39.9% of total iron minerals. Addition of flocculants increases granularity and magnetic force of fine iron-bearing particles and improves iron grade and recovery. The tests with flocculation separation show that a concentrate assaying 56.68% Fe with 81.72% recovery was obtained in a magnetic tube. A concentrate with 56.92% iron grade and 67.96% recovery was obtained by flocculation-magnetic separation with a magnetic cylinder.

Jan 1, 2006

By Sutherland R. A, Rawling K. R

The Nanisivik Mine is located 750 km north of the Arctic Circle at the north end of Baffin Island in the Canadian High Arctic, and has been in production since 1976. The paper describes the regional and local geology and the current mining and mineral processing operations, including recent innovations in each area. The Nanisivik zinc-lead deposits comprise Mississippi Valley type sulphides in a block-faulted sediment sequence of Proterozoic age. The deposits formed in two mineralizing stages by replacement of the carbonate host rock. Exploration techniques adapted to the permafrost environment include high frequency EM and ground probing radar. Core drilling is done with calcium chloride brine but trials with heated flushing water indicate potential for cost reduction. The predominant mining method at Nanisivik is room and pillar. Cut and fill is used in some satellites to the main zone. Due to the permafrost, dry drilling is employed in the underground mining. The permafrost enhances ground stability, permitting large underground openings and, as a result, the use of relatively large scale mining equipment. For power conservation, a remote control system for the ventilation fans has reduced mine power costs. The milling of the simple coarse-grained ore in an arctic environment requires special techniques in the design and operation of the plant for materials handling, utilisation of waste heat, reagent selection and tailings disposal. Regulated heavy metal contents in effluents discharged to the sensitive environment are achieved by natural processes. A recent change from sub-aqueous disposal of tailings to beach type deposition within a cell in the tailings area is reviewed. Planning closure of the property presents special problems and an opportunity for innovative techniques. Approximately 25 per cent of the employees at Nanisivik are drawn from the Inuit population of the Canadian Arctic. As the first permanent industrial activity in the High Arctic some innovative approaches to employee relations were required which have resulted in a very stable, culturally mixed community in a remote location.

Jan 1, 1993

By K H. Esbensen

The Theory of Sampling (TOS) has contributed significantly to chemometrics by allowing data analysts to become more aware of total measurement uncertainty as total sampling error + total analytical error. This has allowed a new view on, for example, validation of multivariate data models and their performance. This keynote focuses mostly on the reverse perspective: how can chemometric multivariate data modelling be of help in an augmented sampling context? The basic principles of multivariate data analysis are presented and application examples are outlined from several areas in the geosciences to facilitate answers to the question posed, including a geochemical multivariate anomaly concept defined by a multivariate background model. Applications from geochemical prospecting, geochemical mapping, environmental chemistry and anthropogenic outlier recognition are outlined, as are the interdependent relationships between geostatistical modelling (variographics) of singular variables versus linear combinations of a multitude of variables, in chemometrics called scores. The potential synergy between chemometrics and TOS is far from exhausted at this time; much work remains.CITATION:Esbensen, K H, 2014. Theory of sampling in a multivariate perspective – what can chemometrics contribute?, in Proceedings Sampling 2014 , pp 7–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By S Jayakumari, E Ringdalen, V Canaguier

Silicomanganese (SiMn), containing approximately 16–30 per cent Si, is produced in submerged arc furnaces using various Mn sources and quartz as the primary raw materials, along with fluxes and reductants. In the high-temperature zone known as the coke bed, a silica-rich slag is formed. SiMn is produced through the reduction of SiO2 from the slag. Dissolution of quartz into slags with different compositions, the primary slag formed from the Mn sources and flux before any MnO reduction occurred, representing conditions at the top of the coke bed, and dissolution of quartz into a partially reduced slag to simulate conditions inside the coke bed has been investigated. Experimental investigations were carried out to study the dissolution of quartz particles of varying sizes, 5 mm and 25 mm in synthetic slags with different compositions at temperatures between 1400°C and 1600°C, with varying holding times. Observed results are compared with liquidus compositions and equilibrium phases for original and formed slags. Particle size has been shown to be of little importance for the dissolution. Quartz dissolved more easily in slag at top of the coke bed than slag in the coke bed. Complete dissolution was observed after 30 mins at 1600°C in all cases, but not after 0 mins.

Jun 19, 2024