Search Documents

By A. G. Galaitsis

The two volumes of this report summarize the noise control work performed by BBN on a rail personnel carrier operated in coal mines. Volume I of the report - submitted November 1977 - describes the aboveground work performed to identify the noise sources, design, fabricate, and install the treatments, and evaluate the treatments through noise and vibration tests. The current volume (II)-describes the underground work conducted by BBN to determine the deterioration, if any, of the treatments when the vehicle is operated normally in a mine. There were no significant changes in the acoustical performance or mechanical integrity of the treatments at the end of a three-month period.

Jan 1, 1980

By F. Dai

Granitic rocks usually exhibit strongly anisotropy due to pre-existing microcracks induced by geologic loadings. The understanding of the rock anisotropy in mechanical properties such as tensile strength is critical to quarrying and stabilization of underground structures. In this paper, Brazilian tests are conducted in combination with MTS material testing machine and split Hopkinson pressure bar (SHPB) system to measure both static and dynamic tensile strength of anisotropic Barre granite. Samples are cored and labeled using the three principle anisotropic directions of Barre granite (BG). These directions are also chosen as the loading directions for the Brazilian discs. For dynamic tests, pulse shaping technique is used to achieve dynamic equilibrium in the samples during the test. Finite Element Method is implemented to formulate equations that relate the failure load to the material tensile strength employing a orthotropic model for Barre granite. For samples in the same orientation group, the tensile strength shows clear loading rate sensitivity. The tensile strengths exhibit clear anisotropy under static loading; while less anisotropy under dynamic loading. The tensile strength anisotropy of Barre granite is interpreted as interactions of the pre-existing microcracks.

May 1, 2009

By C. D. Atkinson

The past few years have seen a much greater concern about air pollution in this country. This concern has led to increased legislation restricting the discharge of many substances such as sulfur dioxide and particulate matter to the atmosphere. In the future, it is anticipated the present permissible emission levels will be lowered. Current and impending restrictions on the emission of sulfur dioxide have brought out the fact that there is a shortage of available low-sulfur fuel for power plants and industrial use which promises to have an economic impact on the nation's energy picture (1) The Pittsburg & Midway Coal Mining Co., under the sponsorship of the Office of Coal Research, has developed a process to produce a fuel capable of meeting the energy requirements of this nation (2) The process is called "The Pittsburg & Midway Solvent Refined Coal Process". The principle product from the process is Solvent Refined Coal which is an ashless, low-sulfur fuel with 16,000 BTU per pound regardless of the rank coal from which it is produced. The product can be burned as either a solid or a liquid fuel. The process appears to be economically more attractive than other methods of alleviating the pollution problems of this nation. In addition to reducing the air pollution caused by stack gases, the product produced is potentially useful as a source of electrode coke and electrode binder pitch, as a gas turbine fuel, in the production of metallurigical coke and pavement asphalt, and as the first step in the overall process to produce distillate fuels and pipeline gas (3).

Jan 1, 1973

By E. R. Parker, R. H. Thielemann

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By R. H. Thielemann, E. R. Parker

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By E. H. Myrhaug, K. Aasly, T. Malvik

Quartz is one of the main raw materials for the carbothermic production of ferrosilicon and silicon metal. The ideal process is written: SiO2 + 2C = Si + 2CO The real process is much more complicated, depending on the quality of the raw materials. Several research projects have been carried out on quartz for the (Fe)Si process during the last 50-60 years. One of the important properties that have been discussed in this review is the volume expansion that takes place between 850 °C to 1000 ºC and explosive disintegration for some quartz types. No final and definite conclusions have been made but several reasons have been mentioned: The influence of the phase transformation to tridymite, which takes place within the same temperature interval, has been discussed in several papers. Alkali impurities have been mentioned as a critical factor for this transformation to take place. Other researchers have mentioned mica impurities as a critical factor for the behavior of the quartz at these temperatures. Studies of fluid inclusions in quartz was reported in some papers focusing on the volume expansion of these during heating as a source of explosive disintegration, especially along planes of healed micro fractures that often contain vast numbers of such inclusions. Several methods for investigations of the important properties of quartz have been presented and these provide a good basis for the further research on quartz raw materials.

Jan 1, 2007

By J. L. Goodier

The paper points up the hesitance of private capital to pursue development of offshore mineral mining endeavors due to the deterrent effect of the clouded legal status of such endeavors. Some states have no laws or regulations to protect the potential exploiter. Others have regulations which give no proprietary rights of exploration to mineral discoveries. The above factors and others are discussed and analyzed in some detail, covering, in turn, summations of the federal regulations and of each of the coastal states. Some comparative analyses are provided, and some recommendations for encouragement to capital investors are made.

Jan 1, 1968

By Ed Labelle, Terry Overton, Gary Bell

"LocationThe Miller Minerals lime and limestone production facility is located in the Temiskaming district of Ontario at Hailey bury on the west shore of Lake Temiskaming. Located less than 300 km from Sudbury, Timmins, Rouyn-Noranda and Val d'Or, the plant is very well situated to market products to the mining, pulp and paper, and environmental industries. Being located a few kilometres from the Trans-Canada Highway and the Ontario Northland Railway adds to transportation efficiencies.ProductsAt Miller Minerals, two principal products in various sizes are produced, which are limestone (CaC03) and quicklime (CaO).HistoryProduction of limestone products began in 1979 at this quarry site. During the 1980s, limestone products were marketed to a variety of applications for mining, forestry, environmental and agriculture applications. In 1990, the production of quicklime products began, following the commissioning of an Italian-designed vertical shaft calcining plant. During the 1990s, both quicklime and limestone products were produced to meet the customers' demands.From the quarry's conception until 1992, the operation was owned and operated by Dymond Clay Products. In 1992, it was purchased by Miller Paving Ltd. of Markham, Ontario, and became a key part of the company's industrial minerals sector of business. Other Miller interests include dolomite, cement, paving materials and waste management."

Jan 1, 2000

"With up to 2,300 m (7,545 ft) of rock on top of it, the Gotthard Base Tunnel, which is scheduled to go into regular operation in December 2016 in the Swiss Alps, is not only the world’s longest, but also the deepest railway tunnel ever built. Accordingly, the temperatures in the tunnel are very high, with the surrounding rock expected to reach 45° C (113° F) once the tunnel is fully operational. Since unrestricted rail operations are only permitted in temperatures of 40° C (104° F) or less, the heat has to be controlled with suitable equipment. Large fans developed and built especially for this application by TLT-Turbo GmbH provide fresh air for regular operations as well as during maintenance and repair work. Separate fans ensure that the emergency exits are properly ventilated in case of fire. In addition to coming up with a technical solution that could handle the special challenges of this project, the engineers and planners had to develop detailed preliminary plans as well as a sophisticated logistics and installation concept.The Gotthard Base Tunnel consists of two 57-km (35-mile) long tubes, one in each direction. Including all connecting and access tunnels, the entire underground system measures 152 km (95 miles). At Faido and Sedrun, at approximately 16 and 36 km (9 and 23 miles) respectively, two multifunction stations were built that cut each of the two tubes into three sections of roughly equal length. Here, trains can make emergency stops and change tracks, if necessary. This is also where eight large axial fans made by TLT were installed that exchange the air, i.e. they extract a certain amount of heated air and inject the same amount of cool fresh air a few hundred meters further down the train tracks. In addition to the four exhaust and four supply fans, 24 so-called jet fans were installed along with associated components like silencers, shut-off dampers, drives and lubrication systems from TLT.In addition to exchanging the air, these fans are used to enable maintenance and repair operations in the tunnel. Current plans call for blocking each tunnel tube for one night per week in order to perform preventive maintenance work, thus enhancing the tunnel’s overall functionality and availability. During these hours, many people will be in the tunnel who require fresh air. “One of the major criteria for winning this bid was the fans’ ability to quickly switch between a wide-range of modes. TLT fans are among the best in the world in this regard,” said Andreas Kuhn, TLT’s project manager for the Gotthard Base Tunnel, about the selection of his company’s fans for this project."

Dec 1, 2016

By Oliver Bowles

The following discussion of waste rock utilization constitutes the fifth paper of the current series of reports on lime- plant quarry problems . As here tofore lime manufacturers are invited to cooperate to the fullest extent by supplementing the Bureau's information with the results of their own experiences and observations . Waste utilization is the key to success in many enterprises , and with a broader knowledge of this branch of the lime industry more economical operation is made possible . Your assistance in compiling additional data on this subject is solicited , and such assistance may be rendered by writing answers to the questions on the final page of this report .

Apr 1, 1923

By H. Eklund, R. T. Hukki

This article presents a simple arithmetic derivation for the relationship between sharpness of classification and circulating load, as well as world-wide industrial data which are compatible with the derived equation. It is shown that the sharpness of classification decreases with increasing circulating load. Based on the evidence available a comparison is presented between the performance of the present-day hydraulic classifiers. In a continuously operated closed circuit grinding system the tonnage and the fineness of the components may be indicated as follows: Eq. 8 expresses the relationship between sharpness of classification and circulating load in closed grinding circuits. If CL = 0, E = 100% according to the definition used. This, however, is a purely theoretical case because any apparatus to be called a classifier must produce the conventional two products. Furthermore, if CL = m, E =0%. In order to visualize the meaning of Eq. 8, the effect of factors d (fineness or percentage of under-size of classifier overflow at size x) and b (fineness or percentage of undersize of classifier sands at size x) should be studied. By the most rigid standard, factor d should be given the value of 100%. By so doing the size of classification is defined as that screen size x through which 100% of the classifier

Jan 1, 1965

By Misra V. N, Cheng C. Y

Two types of Mt Tom Price hematite iron ore from Hamersley Iron P/L were tested using a Humboldt Wedag Jones P40 wet high intensity magnetic separator (WHIMS). The parameters tested were magnetic intensity (7000, 9000 and 11 000 Gauss), groove plate type (8R and 12R) and gap width (2.5 and 1.8 mm). It was found that at 9000 gauss magnetic intensity, reasonably high-grade and recovery in the concentrate were obtained. At 2.5 mm plate gap width, the 12R groove plate performed slightly better than the 8R groove plate. Further testwork is recommended to optimise the magnetic intensity, feed flowrate and pulp density, wash water pressure and flowrate with 12R and 8R groove plates at 2.5 mm gap width.

Jan 1, 1999

By Pedro E. Rengifo

Splicing methods have undergone considerable developments over the last 2Oyears. Continuous conveyor belt service is dependent entirely on the strength and life of the splice to hold the two ends together. Ultimately, belting performance is dependent on the quality, efficiency, and technique of the splicer. As customers demand better belting performance and running tensions increase, the need for splices that perform as efficiently as the belting has increased also. Higher dynamic belt constructions have also dictated the need for "new"sp1icing techniques. Regardless of the belt type used or spliced, one item that is most necessary with all belt types is the quality of the workmanship and standardized splicing methods that employ all of the necessary elements required to ensure reliable field service. This paper will explore the use of Goodyear-issued internal standards for field splicing following the constraints of quality and efficiency for fabric and steel cord reinforced belting. Also included are the 10 most common mistakes made by splicers, Goodyear-issued Field Quality Assurance Standards, and check lists for end users to adhere to the manufacturers' requirements for splicing including materials and specifications for conveyor belt splicing and repairs.

Jan 1, 2004

By P Luo, J E. Danoczi, P Nakutnyy

Sensor-based sorting methods to remove waste or for upgrading ore prior to downstream metallurgical processing is becoming more prevalent for mining operations. X-ray transmission (XRT) sorters are a popular choice for mineral processing plants since they can sort a wide variety of minerals. XRT sorters pass high intensity X-rays through particles to generate images of varying greyscale, based on their effective atomic density. The ore sorter then mechanically separates the particles using algorithms based on the images. A popular test currently used to evaluate the amenability of the ore to XRT sorting is to pass the particles through the sorter and obtain the greyscale images showing mineralogical differences. This test provides information on the mineralogical heterogeneity between ore particles for their separation. However, it does not provide an understanding of the actual mineralogical composition of the ore or information pertaining to which other minerals may respond in a similar manner, nor does it provide liberation information. This paper describes a test that combines high resolution X-ray micro Computer Tomography (CT) combined with QEMScan to obtain information about amenability of ore to XRT sorting and to obtain valuable information that can streamline metallurgical testwork programs. This test also provides information relating to particle thickness and associated X-ray attenuation coefficients, desired mineral presence and mineralogical information relating to associated minerals and clays to assist with developing sorting algorithms. Combining the CT and QEMScan can address many limitations of the current method to determine whether XRT sorting technology is appropriate for particular ores. Mineralogy information from QEMScan can identify incidences of; mineral encapsulation, problematic clays, detrimental minerals as well as calibrate the greyscale values of CT data. Additional 3D CT imaging carried out on cores provides spatial information of the minerals within the ore and mineral grades.

Nov 10, 2020

By A Karrech, C Schrank, O Gaede, I Canbulat

Strain-based failure criteria have several advantages over stress-based failure criteria: they can account for elastic and inelastic strains; they utilise direct, observable effects instead of inferred effects (strain gauges versus stress estimates) and they model complete stress-strain curves, including prepeak, non-linear elasticity and post-peak strain weakening. In this study, a strain-based failure criterion derived from thermodynamic first principles utilising the concepts of continuum damage mechanics is presented. Furthermore, implementation of this failure criterion into a finite element simulation is demonstrated and applied to the stability of underground mining coal pillars.In numerical studies, pillar strength is usually expressed in terms of critical stresses or stress-based failure criteria where scaling with pillar width and height is common. Previous publications have employed the finite element method for pillar stability analysis using stress-based failure criterion, such as Mohr-Coulomb and Hoek-Brown, or stress-based scalar damage models.A novel constitutive material model, which takes into consideration anisotropy as well as elastic strain and damage as state variables, has been developed and is presented in this paper. The damage threshold and its evolution are strain-controlled, and coupling of the state variables is achieved through the damage-induced degradation of the elasticity tensor. This material model is implemented into the finite element software Abaqus and can be applied to 3D problems.Initial results show that this new material model is capable of describing the non-linear behaviour of geomaterials commonly observed before peak strength is reached as well as post-peak strain softening. Furthermore, it is demonstrated that the model can account for directional dependency of failure behaviour (ie anisotropy) and has the potential to be expanded to environmental controls such as temperature or moisture.CITATION:Gaede, O, Schrank, C, Canbulat, I and Karrech, A, 2014. A strain-based failure criterion for pillar stability analysis, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 393–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Lori Bassman, Cassandra George, Cullen McMahon, Md. Zakaria Quadir, Michael Ferry

"Complete and accurate analysis of subgrain microstructural features must include three-dimensional information. Three-dimensional electron backscatter diffraction (EBSD) data can be used to characterize these features; however their boundaries first must be determined. This cannot be accomplished simply with pixel-to-pixel misorientation thresholding because many of the boundaries are gradual transitions in crystallographic orientation. Fast Multiscale Clustering (FMC) is an established image processing technique that we have combined with quaternion representation of orientation to segment this kind of data. Segmentation algorithms often have issues handling images with both distinct and subtle boundaries. Our implementation of FMC addresses this by using a novel distance function and statistical analysis to take into account the variance in orientation of each feature. Although FMC was originally a twodimensional image processing algorithm it can be generalized to analyze threedimensional data sets. As an example, a segmentation of microbands in cold-rolled aluminum is presented.IntroductionThree-dimensional electron backscatter diffraction (3D-EBSD) is a method for mapping the local crystallographic orientations of points in a volume. The technique uses a dual beam platform consisting of a focused ion beam (FIB) and SEM with EBSD, where FIB is used for serial sectioning and EBSD for orientation mapping of 2D slices. These 2D slices may then be stacked to create a 3D volumetric data set.Typical uses of such a data set include characterizing the geometries and crystallographic orientations of surfaces between structures in 3D [1-5]. This involves identifying boundaries accurately, either in 2D slices with subsequent 3D reconstruction (as illustrated in Figure 1) or in the 3D data set. All such data sets present the challenges of i) aligning data slices to correct for instrument drift, ii) identifying relevant boundaries, and iii) implementing appropriate smoothing or interpolation algorithms. The focus of this paper is boundary identification."

Jan 1, 2011

By D. R. Tesarik

Researchers from the National Institute for Occupational Safety and Health (NIOSH)1 and engineers from Placer Dome, Inc.2, conducted an underground rockfill span test at the Turquoise Ridge Mine near Golconda, Nevada, USA with the purpose of improving safety and increasing productivity by using a bulk mining method instead of drift and fill. A rockfill sill was constructed by mining and backfilling six adjacent, parallel drifts and then undercutting the sill with a 13.7 m (45 ft) wide and 30.5 m (100 ft) long room. Displacement measurements from vertical borehole extensometers installed in the mine roof and rockfill indicated that the sill remained stable with a maximum vertical deformation of less than 5 mm (0.2 in). These results were confirmed by visual observations and calculations from a validated three-dimensional numeric model of the sill. The numeric model was also used to simulate load on the sill produced by dislodged roof material in the shape of a 11.0 m- (36 ft-) high triangular prism with base measurements equal to those of the sill. Failure in the bottom third of the sill occurred with this additional load.

May 1, 2007

By W. J. D. Stone

Many of the common valuable minerals have a magnetic susceptibility which is sufficiently high to render them amenable to magnetic separation. In addition,, many minerals which form the unwanted constituents of an ore can be removed by magnetic means. Magnetic separation in general has suffered seriously from, the lack of a high intensity wet separator. It is only recently that such a separator has become available to the industry. Prior to this, high intensity magnetic separation has been limited to the use of the dry techniques. Since the introduction of the Jones Wet High Intensity Magnetic Separator, extensive test work has been conducted to investigate possible applications. From the investigations conducted and the discussions that have taken place in the industry, it is apparent that the important mineral characteristic of magnetic susceptibility is not receiving the attention that it deserves. Applications for high intensity wet separation are being found in areas hitherto not considered.

Jan 1, 1963

By Anil Bhandari

Using subsurface data collected at each drilled shaft location is an ideal approach for conducting drilled shaft design. However, conducting subsurface tests at each drilled shaft location and subsequently performing the drilled shaft design can be a daunting task for a noise barrier wall that is divided into six (6) sections and stretches for approximately four (4) miles. In addition, having individual drilled shaft designs complicates the construction process. Grouping the subsurface conditions into broad categories and performing the design for each of those categories is an attractive alternative to the design per boring approach. Currently there are no existing guidelines to aid a designer on grouping the subsurface conditions for the drilled shaft design for the noise barrier walls. Therefore, a method was developed based on the Standard Penetration Test (SPT) N values of the near surface soils to categorize the soil profiles into distinct categories. Since the soil engineering properties of the near surface soils are known to be critical for drilled shaft lateral capacity, these soils were emphasized in the methodology. This method was successfully implemented for the design of drilled shafts supporting the noise barrier walls along the I-20 in Columbia, SC. For this project, two distinct soil profiles, labeled as ?strong? and ?weak?, were used. An overview of the soil profile grouping methodology is presented as well as the vertical and lateral drilled shaft capacity analyses for this project for the two general soil profiles. The analyses indicated that the axial capacity governed the design in the ?weak? soil profile and the lateral capacity controlled the design in the ?strong? soil profile. However, this is not a generalization and whether the axial or the lateral capacity governs the design of drilled shaft depends on the soil profile and design loads. Nonetheless, our findings emphasize that both lateral and axial capacity should be checked for drilled shaft design even when the vertical load are minor.

Jan 1, 2011

By J. R. Koehler

Although two-entry yield pillar-based gate roads supported by wooden cribs have been commonly used throughout longwalling in the Wasatch PlateadRoan Cliffs coalfield of central Utah, a three-entry yield-abutment gate road configuration was recently trialed in the Hiawatha Seam at the Genwal Resources (GRI) Crandall Canyon No. 1 Mine, near Huntington, UT. Pillar, entry, and cable bolt performance were monitored through second panel mining using a fairly extensive array of geomechanical instruments installed over a span of four crosscuts. Ground pressure and entry closure measurements confirmed that the 9.1-m-wide (30-ft) yield pillar was partially shielded from first panel longwall loads by the 36.6-m-wide (120-ft) abutment pillar, and consequently, experienced only minor yielding until the approach of the second panel face. Complete yielding of the 9. I-m-wide (30-ft) pillar occurred when the second panel was approximately 6.1 m (20 ft) inby the instrumentation site. Average cable bolt loads and differential roof sag remained low through second panel mining and tailgate entry ground conditions were excellent; however, very high ground pressures in the abutment and yield pillars, and second panel rib strongly suggest a high potential for coal bumps utilizing this gate road configuration at mining cover depths in excess of 396 to 457 m (1300 to 1500 ft). This conclusion is supported by the suspected occurrence of small coal bumps along the abutment pillar ribs, observed indirectly as fresh debris in the middle entry just behind the second face. This paper presents a case history developed from the geotechnical measurements and on-site observations of this unique application of a yield-abutment gate road configuration and cable support system in the Hiawatha Seam.

Jan 1, 1996