Search Documents

By Mingming Zhang, Marshall S. Coe, Marcelo W. Andrade

To supply iron units and flux burden in blast furnaces, sinter basicity is one of the vital parameters for sinter plants. The sinter basicity also plays an important role in sinter quality since it imparts the formation of different mineral phases in sinter. Pot-grate sintering tests were carried out with low and high basicity to investigate the effects of sinter basicity on sinter mineralogy, properties and productivity. It was found that with an increase in sinter basicity, both sinter productivity and reducibility (RI) increased. Tumbler index (TI) and low temperature degradation index (LTD) of high basicity sinter were comparable to low basicity sinter. Softening and melting tests showed that sinter with 3.5 C/S basicity had slightly higher softening temperature comparing to lower basicity sinter with C/S 2.6, acid and fluxed pellets. XRD analyses confirmed the formation of silico-ferrite of calcium and alumina (SFCA) and calcium ferrite (CF) in the tested sinter samples.

Jan 1, 2015

By James H. Aase

[This study provides data on the physical and hydrological makeup of the ,t hakes waterway system and forecasts quantities, traffic patterns, and ping cost of prospective bulk mineral commerce projected to be transported it. Factors affecting the shipping cost of iron ore, bituminous coal, imestone were quantified and integrated into a computer program that can d to estimate costs under varying sets of conditions. Combined ship of iron ore, bituminous coal, and limestone in 1995 were estimated at million tons. The cost of operating the U.S. vessel fleet for trans-ng an indicated 80 percent of this traffic tonnage was projected to be $163. 5 million.]

Jan 1, 1970

By J Jackson, M F. Young

"Ore is the economic portion of a mineral deposit that can be extracted economically. Hence an ore type is a classification of the ore based on one or more dominant characteristics in order to enable communication between unit operations and/or technical disciplines.In project evaluation, ore types are often defined early based on geological observations by geologists and initial metallurgical testing is based around this classification even though a number of processing options can be under evaluation. However, the geological drivers of performance for each of these processes can be very different and the ore type classification for one process may not be relevant for another. In operations an ore type, as either defined in the project evaluation phase or those that evolve with additional knowledge, is unlikely to provide the knowledge required across all the unit operations. The ore type has a meaning to someone but does not necessarily for all unit operations across the value chain.Geometallurgical or orebody knowledge has evolved through the consideration of multiple processes within the value chain, the improved understanding of variability of process performance within ore types and the effect on the complexity of the mineral extraction processes. Furthermore orebody knowledge has been moving from personal based knowledge and understanding to a more process oriented approach where measurement and spatial and process performance modelling is playing a greater role. Advances in mine planning and scheduling allow for both detailed analysis of the block model and the expected extraction processing attributes across various time scales. This capability of analysing and describing the complexity still requires to be communicated to the various unit operations, which may be beyond the traditional classification of an ore type.The limitations of an ore type and potential alternatives to enable the relevant information to be communicated to the relevant groups are outlined through a number of case examples across the value chain.CITATION:Jackson, J and Young, M F, 2016. Ore Type – Everything to Someone but Nothing to Anyone, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 267–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By T Sparks

The Collie River catchment, located approximately 200 km south of Perth, covers an area of around 2830 km2 and is the source of run-off to the Wellington Dam, an important irrigation water resource for the Collie Irrigation District. The salinity of the Wellington Dam has increased due to historical clearing and irrigators currently use water with salinity levels approximately twice that of the Murray River in South Australia (Water and Rivers Commission, 2001). The Collie River Salinity Situation Statement (2001), released by the Water and Rivers Commission (now the Department of Water), identified realistic actions that could achieve the salinity reduction target. Subsequent benefit-cost analyses and prefeasibility studies recommended the diversion of the most saline flows in the Collie River away from the dam as an immediate intervention (URS, 2003). The East Branch of the Collie River above the locality of Buckingham (20 km east of Collie) contributes around half of the salt that flows into the Wellington Dam and the diversion and storage of the saltiest flows from the East Branch at Buckingham was identified as a viable option for reducing salinity in Wellington Dam. The proposal had one problem û the water could not be disposed of as quickly as it was diverted. However, in the vicinity of the diversion site were a number of coal mine voids and after preliminary discussions, the Government/Griffin Coal alliance was formed and from this the opportunities have continued. Diverted water would be stored temporarily in an adjacent mine void (Chicken Creek 4 void) and then disposed of to the sea. The disposal options included Western Power CorporationÆs saline discharge pipeline from Collie Power Station, or a new pipeline. The diverted water was also identified as a potential raw source for treatment and use in industry. This has opened up opportunities including desalination, water efficiencies in the power stations, increased reliability of water supply for the power stations, water for new industries, wastewater disposal options and extra water for PerthÆs water supply. In the process of solving the water storage problems the project introduced a range of mine water quality problems û heavy metals and pH û and the Department of Water (DoW) is now working with the mining industry and the Centre for Sustainable Mine Lakes (CSML) to develop treatment and management technologies. The project has received support and funding through the National Action Plan for Salinity and Water Quality (NAP) and it has been possible to accelerate and enhance this project as a result of NAP. The DoW has developed the proposal to an advanced stage and gained approvals for the capital diversion program to go ahead. The partnerships have expanded to include the second mining company, Premier Coal, the Water Corporation, Western Power and the Harvey Irrigation Cooperative. The proposal could feasibly result in a $90 million integrated water management initiative for Collie using the latest technology, mining operations and providing water for value adding industries in the local area. The DoW is not a mining company; however, our experience in managing water in times of shortage, environmental water quality criteria, competition for water and managing community expectations will have the same success factors:consultation and knowing your community and stakeholders, sharing issues and working in partnership can provide results far greater than the initial issue, even brackish water has value, every sector is in competition with each other and has to have a share of the water, an integrated approach can provide opportunities for development in areas of water shortage, and never think of water as wastewater.

Jan 1, 2006

By T. H. Dubaniewicz

Many mines rely on toxic gas sensors to help maintain a safe and healthy work environment. This report describes a prototype monitoring system developed by the U.S. Bureau of Mines (USBM) that uses light to power and communicate with several remote toxic gas sensors. The design is based on state-of-the-art optical-to-electrical power converters, solid-state diode lasers, and fiber optics. This design overcomes several problems associated with conventional wire-based systems by providing complete electrical isolation between the remote sensors and the central monitor. The prototype performed well during a 2-week field trial in the USBM Pittsburgh Research Center Safety Research Coal Mine.

Jan 1, 1995

By R. Karl Zipf, Z. T. Bieniawski

"Fracture mechanics plays an important role in studies of geologic materials such as rock and coal. Yet fracture data are scarce for rock and most limited or unreliable for coal. A testing system was developed which can apply mixed mode loads to a crack tip in many rocks and geologic materials. It is possible to subject the test specimen to pure mode I, various mixed modes and a nearly pure mode II fracture load. The system is currently used to study the mechanics of fine fragment formation in various coals. Experimental measurements include KI and KII' fracture velocity and acoustic emission.INTRODUCTIONA major research program at The Pennsylvania State University is directed to understanding the fundamental mechanics of fine fragment formation in various coals. The program represents an effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners. The principal source of the respirable coal fragments is the cutting operation which forms and liberates the particles by a fracture process. Present understanding of the mechanics of the events which form and liberate these particles is meager (Cook, 1982).Current knowledge of the fundamental mechanisms of coal dust generation and entrainment in terms of the underlying fracture mechanics is critically needed to improve and possibly control the processes involved. Whether the cutting operation is done with a 'continuous miner' cutting machine, a plow or a longwall shearer, it is fundamentally a problem of mixed-mode crack propagation. When a cutting tool interacts with coal, it causes numerous cracks to propagate through the intact material. Numerous larger fragments are broken free, but another quantity of undesirable fine fragments is also created. The formation of these respirable fragments may be a direct result of the crack propagation process; hence, a thorough understanding of the fracture mechanics of coal is required to minimize production of the unwanted fine fragments.In most rock engineering applications, the rock material properties are of secondary importance to the rock mass properties; however, for rock fragmentation and rock cutting problems, it is rock material properties such as fracture toughness which are of prime interest (Bieniawski, 1980). Several rock cutting and rock failure theories have been proposed, but it is only very recently that fracture mechanics concepts have been successfully applied to the study of rock cutting mechanics. All cutting models seek to predict the cutting forces and the cutter geometry necessary to cause rock breakage and chip formation given some fundamental mechanical properties ~f the rock. Such models have wide applications in drilling, tunnel boring and mining problems. Nelson et al., (1985, 1986) has provided a very useful correlation between the laboratory measured fracture mechanics properties of rock and the performance of the disk cutters on tunnel boring machines."

Jan 1, 1989

By ?. S. Potokin

"In general the electric pulse treatment is composed from two processes – electric pulse grinding and electric explosive (electric discharging) activation. The electric pulse grinding with the effect of selective destruction refers to a major slag fraction, more that 2-5 mm, when a one can see a physical prerequisites for electrical breakdown of the slag particles. The electric pulse treatment of slag is considered as an additional operation in the technological scheme extraction of non-ferrous metals from copper smelting slags in addition with mechanical grinding, flotation enrichment and acid leaching. Studies of the reprocessability of pelletized slag have shown the possibility of higher extracting non-ferrous metals via flotation after electric pulse disintegration (EPD) treatment. By using EPD of slag pellets, it is possible to increase the non-ferrous metal yield to concentrate by 18-24%.INTRODUCTION The use of the explosive effect of the plasma discharge channel at electrical breakdown of a solid at a pulsed high voltage is the physical basis of the electric pulse method of destruction of geomaterials (Vorobiev et al., 1971; Andres, 1995; Semkin et al., 1995). The flowing of a pulsed current in the discharge channel is accompanied by a sharp increasing of plasma’s temperature and pressure, leading to a supersonic expanding of the discharge channel, the formation in the solid of intensive mechanical tension field, spreading of cracks, and eventually, to the destruction of the solid. Fragmentation and grinding of ore and mineral aggregates by electric pulse method due to a number of specific physical mechanisms of power load and crack formation, belonging only to this method, is different by high selectivity of destruction. This ensures better liberation of grains of individual minerals and their better preservation from destruction and less formation of a slurry output. These features creates the prerequisites for a more complete extraction of a useful mineral in the concentrate during ore dressing, to improve the quality of concentrate. In contradistinction to mechanical methods, electric pulse technology does not contaminate the product with instrumental metal, material of lining and grinding bodies. The possibility simply and in a wide range to change the dynamic load character allows to regulate the granulometric composition of the product of grinding, to obtain a narrower class of product size than is possible with mechanical grinding. The product of electric pulse grinding is characterized by less roundness and large specific surface area of grains due to the trait, that a new surface is formed in the process of splitting during the expanding of cracks. The degradation product has increased sorption and reactivity in chemical reactions. Liberation of the mineral inclusions particle better corresponds to their initial natural state in the rock and this is the great importance for the study of mineral raw materials."

Jan 1, 2018

By K. W. Cathrine Solem

Filtration of liquid aluminium is widely used in the industry for the removal of inclusions, and Ceramic Foam Filters (CFFs) are often the filtration media of choice. It is known that PH3 (phosphine) can be released from used phosphate bonded CFFs when in contact with water. Additionally, there is a need of an improved understanding of the thermal stability and the chemical reactivity of these types of filters, as there is limited information available in the public domain. In the present preliminary study, three CFFs, i.e. Substrate 1–3, with varying AlPO4 (aluminium phosphate) content were studied under controlled conditions. Samples of the substrates, as produced and in contact with 5N pure aluminium, were heat-treated in a vacuum induction furnace at 850 °C and 1300 °C, as well as thermally studied at 850 °C using a Differential Scanning Colorimeter connected to a Thermogravimetric Analyser (DSC-TG). All tests were performed under an inert atmosphere of argon (Ar). Mass changes of ∼0.001 % were registered for the pure substrates, and 0.003-0.10 % when in contact with aluminium. In the latter case, diffusion of P (phosphorous) from the bulk of the substrate to the interface was established to have taken place. A colour change, from white to orange/brown, was also observed at the interface, which is a clear sign that a chemical reaction has taken place. As a result, the thermal stability of the substrates can be questioned under present conditions.

By Ian Ewart, Trevor Bergfeldt, Gourab Satapathy, Ajay Patel

"Conventional electrowinning (EW) of nickel from sulfate electrolytes is complicated by several factors including the requirement for a diaphragm cell to separate the anolyte and catholyte and the need to minimize nickel mist emissions. Developed and commercialized by emewCorporation, this novel process electrowins high purity nickel cathode (99.5%) from copper refinery bleed streams using the proprietary emew vortex EW technology. The emew nickel process incorporates high flow rate in an enclosed cylindrical EW cell operating at high current densities that overcomes the challenges of conventional nickel EW and completely eliminates the risk of nickel mist emissions. The tubular cathodes are easily harvested and mitigate the effect of plating stresses inherent in nickel EW. The present paper describes the emew nickel process and its most recent application to copper refinery bleed streams at full-scale.INTRODUCTION To meet the stringent demand of customers, nickel producers are giving prime importance to production of high purity nickel cathodes. The major challenge for refineries is to improve cathode quality and appearance despite fluctuating electrolyte impurity levels. The basis of achieving good quality cathode includes the control of electrolyte impurities and consistency of specific process conditions. The commercial operation of emew nickel technology has been successfully implemented and has demonstrated the ability to produce high quality nickel cathode from refinery bleeds. This paper emphasizes the importance of upstream impurity removal to achieve the required nickel emew feed composition by evaluating the benefits of using selective precipitation as a purification scheme with the aim of improving the overall nickel recovery while ensuring suitable nickel concentration in the advanced electrolyte is achieved. Nickel electrowinning is similar to other electrowinning processes that employ insoluble metal anodes & cathodes. It requires the passage of direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. For the recovery of nickel from solution, the most common methods are electrowinning and hydrogen reduction. Electrowinning usually occurs from sulfate, chloride or mixed sulfate/chloride electrolytes. In sulfate electrolytes, nickel electrowinning cells are normally designed to achieve specific criteria as outlined below (Robinson & Tuppa, 2002):"

Jan 1, 2017

By K. Barani, F. Moradpouri, M. Godarzi

A sampling campaign carried out on the lead flotation circuit at Lakan lead-zinc processing plant demonstrated that the Pb recovery was only about 68-69%. Characterization of the Pb flotation tailing showed that 61.4% of the Pb is in the –37 μm size fraction, which is difficult to recover by flotation. Batch flotation experiments were carried out on a plant sample of the lead flotation feed and high-intensity conditioning (HIC) was used to improve flotation recovery. The results showed that increasing the collector conditioning time from 1 to 3 minutes significantly increases the Pb recovery from 42.5% to 57.3%. Further increases in conditioning time to 5 to 7 minutes decreased the Pb recovery. With a collector conditioning time of more than 3 minutes, due to the surface cleaning effect, increasing collector and frother dosage improved the flotation selectivity and recovery, even at higher collector dosages. The Pb recovery increased from 69.1% to 79.8% with increasing impeller speed from 600 to 1250 r/min. HIC increases the flotation kinetics and greatly improves the flotation recovery and concentrate grade.

Apr 2, 2022

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology for supporting the Industry 4.0 has become the target of academic research in many sectors. This study reviewed the trends of open-source technology, its forms, and some industrial applications. As a case study using open-source hardware and software for the mining industry, this study proposed a low-cost environmental monitoring system for non-metallic underground mines to support mine safety and occupational health issues. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device. An open-source software, MIT App Inventor, was used for developing an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a non-metallic underground mining site to assess the performance of the system in both mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors still exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors

By E. W. Felegy

Since 1920, the Bureau of Mines and, other agencies have conducted numerous investigations of methods of communication for use in mines in times of disaster or emergency. The results of these investigations have been reported in various publications (3, 4; 5, 6, 8, 9, 10, 11, 12, 13, 14, 15, 16). In November 1944, the Bureau of Mines resumed the study of emergency underground communications. Until March 1946, the program was directed toward reexamining methods of underground communication that indicated possibilities of success. Since April 1946, the principal interest of this investigation has been in methods of application of radio to communication in mines, low-frequency radio seeming to offer the most promise as a successful method of emergency mine communication. Results achieved in reexamining other methods and in the investigation or the application of low-frequency radio between November 1944 and September 1946 were reported previously in a publication entitled "Some Studies on Emergency Mine Communications".

Jan 1, 1948

By Louis A. Panek, John A. Stock

A flat slot is created in rock to cause stress relief effects in a pair of hydraulic borehole pressure cells (previously installed in drill holes above and below the slot ) , which act as sensing devices . This relief is annulled by repressuring the slot by means of a flat hydraulic cell . The slot pressure at annulment is taken to be the existing ground stress at right angles to the plane of the slot . A number of trial installations in the rib of a mine drift showed that for a valid determination of ground stress the sensing devices that respond to relief and repressuring must be within a specified zone close to the pressure transmitter ; otherwise the indicated ground stress may be excessive . By using an additional pair of borehole pressure cells , installed a few feet away , the existing rock stress can be redetermined at intervals , irrespective of a change of stress intensity subsequent to the initial installation . Based on these findings , equipment and procedures have been developed that make possible the installation and operation of a permanent rock stress monitoring station for observing mining - induced stress changes . The station consists of a 12 - in - wide hydraulic pressure cell cemented in a flat slot and four 2- by 8 - in flat hydraulic pressure cells in nearby drill holes . All drilling for the installation can be done with an air leg drill and conventional bits . Once the installation is completed , all required information is obtained by Bourdon pressure gage readings . The apparatus is simple , relatively inexpensive , and reliable under operating conditions in a wet mine . Unlike most methods of rock stress determination , this scheme permits periodic remeasurement of absolute rock pressure over several years , without additional drilling or instrumentation . Similar to other flat slot procedures , stress measurements are obtained without making auxiliary tests to determine elastic

Jan 1, 1964

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using an untreated rock dust and a rock dust treated with an anti-caking additive. Using PDM 3600s and 3700s, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine (BEM) using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device. INTRODUCTION Two factors have combined to renew concern regarding respirable dust measurements and compliance. This renewed recognition is due to two regulations that have modified operators’ rock dust schedules. First, the 80% incombustible requirement in intake entries has increased both on-section and outby-the-section rock dusting. Secondly, the recent respirable dust regulation change that has increased the number of respirable dust samples taken per sampling cycle. Previously, when only 5 samples were needed bi-monthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule. The significant number of samples now required under new regulations combined with the need to maintain 80% total incombustible content in active mining areas require the schedules for respirable dust sampling and rock dusting to intermix. This raises concerns about the amount of rock dust that potentially is included in the sampler weight gain. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 (effective August 1, 2016) increasing concern that rock dust contamination may be an issue. Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application or to schedule rock dusting during a maintenance shift when the number of miners present is lower. NIOSH’s research examining the quality of rock dust has led to the development of hydrophobic rock dusts."

Jan 1, 2017

By Carle R. Hayward

LEAD ore smelting plants have been operating in general at reduced capacities and secondary lead has assumed relatively more importance during the last year. Present smelting practice results in a large amount of dross, often over 25 per -cent, from blast-furnace lead. This is usually treated at a fairly high temperature in a reverberatory furnace to remove part of the lead and produce a matte-speiss product which is shipped to a copper plant. Few smelters are satisfied with this 'treatment. The fume losses are high and the matte-speiss contains considerable lead. It would seem that a fruitful field for research was open here.

Jan 1, 1934

By F. Julius Fohs

CENTRALLY located with relation to the largest iron- and steel-producing districts of the United States, the fluorspar-deposits of Kentucky possess increasing interest and importance. As typical of the numerous fluorspar-mines of Kentucky and Illinois, I have selected for description the Memphis., because it and others of its immediate group exhibit the conditions characteristic of all. I. THE MEMPHIS MINE. This mine lies 5 miles NW. of Marion, in Crittenden county, Kentucky, a station on the Chicago and Nashville division of the Illinois Central R. R. For the first mile and a half out of Marion we see only Birdsville or Middle Chester sandstones of Mississippian age. Then we cross a fault of some 350 ft. displacement, and the Ste. Genevieve oolite sets in. Beyond the fault, oolite is the predominant rock, except that the bills to the north have a capping of Cypress or lowest Chester sandstone, 80 ft. below which is an outcrop of from 6 to 10 ft. of Ste. Genevieve (Rosiclare) sandstone. Occasional sink-holes are noticed, and as the mines are approached evidence of faulting is again seen.. A line of crude head-frames and open-cut dumps, extending for more than a quarter of a mile, marks the Klondike vein. The open-cuts are from 15 to 20 ft. deep, and in most of them, from the surface down, was found the reddish gravel which is really fluorspar-some of it white or purple and crystal-clear (if the red clay is washed off), and some carrying iron and silica, and stained by waters from the decaying limestone walls. In one of these cuts, at a depth of 20 ft., white and purplish honey-combed fluorspar was found, in which the larger cavities are due to limestone and calcite leaching, and the minute ones to the leaching of zinc-blende.

Apr 1, 1909

By Joseph P. Nugent

The new combination gypsum plaster and gypsum wallboard plant of Compania Industrial Kaiser S.A., the first of its kind in Mexico went into production in April of 1969. This was approximately fourteen months from the signing of the formal order for the plant and equipment. Compania Industrial Kaiser S.A. is an affiliate of the Kaiser Gypsum Company in the United States and will market practically the same line of products and to the same standards as those produced in American plants. Located in the City of Puebla, the plant will readily service the major Mexican sales areas. It is approximately 85 miles away from Mexico City on a modern, four-lane, divided highway and distribution to other major consumer areas can be readily effected by the use of a good highway system, as well as, by rail. This, plant is the, sixteenth Gypsum Wallboard Mill supplied abroad by my company, United States Wallboard Machinery Company. Other installations are in Australia, New Zealand, Chile, England, Scotland, Ireland, Finland, South Africa, Latvia and Germany. Two new mills are on order; a small unit for Brazil and a comparatively large unit for New Zealand. All these mills have one thing in common with plants in the United States and Canada; they are equipped with standard, time-proven and tested equipment and they are designed in accor¬dance with the latest engineering thinking in order to produce efficiently, the highest quality product at lowest cost. They differ generally in the size of plant, the factors that brought them into being and in the market that they supply. I believe that these differences will be of interest to you.

Jan 1, 1969

By John D. Watson

The results of extensive field tests of a new and powerful method of hard rock excavation are presented in this report.* The method, known by the acronym REAM (Rapid Excavation and Mining), employs high velocity, smooth bore cannons to efficiently deliver energy to the rock and has been demonstrated for underground tunneling, drilling, surface benching, scaling, and secondary breakage in hard granitic rock at the Hope Valley Mine test site in California. Solid projectiles made from inexpensive materials such as concrete or steel, and weighing from 8 to 12 pounds, are launched by conventional high speed cannons and impact the rock at velocities of 5000 feet per second--an impact energy of about 4 million foot pounds (Figure 1). The energy applied at peak pressures of nearly 2 million psi over a period of tens of microseconds breaks down the rock by a complex mechanism of crushing, spalling, and initiation and propagation of fractures produced by the interaction of successive impacts and free surfaces. The main objective of the tests during 1973 was a demonstration of controllability of the underground operation of a silenced cannon. To accomplish this objective a 90-mm cannon

Jan 1, 1974

By Allen L. Frank

The uranium mine environment is characterized by airborne radon-222 and its daughter products to which miners are exposed through breathing and by gamma and X rays from the uranium-235 and uranium 238 chains to which the miners are exposed externally. The nature of the radon-daughter concentrations and the methods used to define and measure the exposures are explained through an extensive review of the literature. An improved passive track-etch dosimeter for personal use is proposed which has a measurement range of about 30-400 WLH with a 95% confidence interval to ~25% for individual detector measurements in relatively stable mine air. Some measurements of these dosimeters adapted to environmental use are also presented. A program of development for enhancement of dosimeter sensitivity and greater accuracy of measurement is outlined. Extensive gamma-ray survey measurements were made in two Colorado and three New Mexico mines. Follow-up personal miner dosimetry with LiF TLDs was done at the mine with the highest exposure rates, The average miner exposure rate measured was 4.27 mR per day, or 9.3 of the maximum permissible level averaged over 13 weeks. Comparisons are made with previous mine surveys and their value in estimating miner exposure is discussed. Some depth-dose measurements made using Lucite as the absorber are evaluated.

Jan 1, 1978

By William G. Ryan, David S. Graham, Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"The St. Croix River Crossing project on the Minnesota-Wisconsin border has been in the process of planning and public debate for two decades, with several changes in alignment. During the course of the earlier planning process in 1995, a drilled shaft load test was performed to obtain preliminary design information. There were some difficulties in maintaining stability within the weak sandstone bearing formation, and the measured axial resistance was relatively low. Subsequent experience by the Minnesota Department of Transportation with similar weak sandstones on the I-35W project suggests that improved construction techniques using modern drilling fluids may offer opportunities for improved performance. During final design in 2012 a second load test program was performed of a full scale test shaft constructed using polymer drilling fluids. The stability of the socket excavation in the weak sandstone appeared to be greatly improved and the measured axial resistance significantly higher.This case history illustrates the excellent performance that drilled shafts can provide in even relatively weak sandstone bedrock as well as the profound influence on axial resistance associated with the construction techniques used. The improved resistance values obtained by the new load test with more recent construction technology allowed the foundation scheme to be substantially optimized with respect to the number and size of required drilled shafts, reducing the size, cost, and risk of the coffercells and footings.IntroductionThe Minnesota Department of Transportation (MnDOT) has awarded the first phase of a bridge construction project that will cross the St. Croix River between Oak Park Heights, MN and St Joseph, WI. The first phase construction contract involves building the river pier substructures including groups of drilled shafts beneath each tower leg. A general location of the bridge project is provided in Figure 1.Prior to award of the construction contract, two separate design-phase axial load tests were performed on non-production drilled shafts with rock sockets. Both tests were static, bottom-up tests using the Osterberg Cell (O-cell). The first test was performed in 1995 when final design and construction was thought to be imminent. After years of public debate and literally, an act of Congress, design of the project was finally restarted and a second load test performed in 2012. The 1995 test was conducted on the Minnesota bank approximately 900 ft southwest of the St. Croix River bank. The 2012 test was conducted in the river about 2,100 ft northeast of the1995 test location. A plan-view of the project indicating the test program locations relative to the bridge alignment is provided in Figure 2."

Jan 1, 2015