Search Documents

By K. B. Venkatesh

In view of the importance of size reduction operations from the energy consumption point of view, during the past one hundred and fifty years a number of attempts have been made to develop a general energy-size relationship. However, to date it has not been possible to clearly define the scope of application of various laws proposed, though Bond law has been widely used with a moderate degree of success. It was, therefore, decided to carry out a thorough analysis of the batch ball mill grinding data available in the literature on several minerals that were ground under normal range of operating conditions. In particular, relationships proposed by Bond, Kapur, Voller and Morrell were examined in detail. It was found that the relationship proposed by Kapur in terms of the mean particle size provided a more accurate basis for estimation of energy. The value of the exponent of mean particle size in this relationship, a, is same as the exponent of the particle size in the expression for the grinding rate parameter: ki = Axia, provided the particle size distribution range corresponds to the self-similar or self-preserving regime. In this regime, mean particle size is proportional to the 80 percent passing size and size modulus. From the practical application point of view, it was possible to describe the variation of µ1 over limited, but significantly broad size range, using a constant value of a. Thus, by carrying out a few batches, grinding experiments over the size distribution range corresponding to the contents of the production mill, the applicable value of a can be determined. Keywords: energy-size relationship, ball mill, mean particle size, self-similar size distribution regime

Sep 1, 2012

By Yasuhiro Konishi, Norizoh Saitoh

"We have developed new recycling technologies, based upon an eco-friendly biotechnology, in order to extract precious and rare metals sourced from post-consumer products. Recently we have been focusing on the metal ion-reducing bacteria, Shewanella algae and Shewanella oneidensis, which are able to reduce and deposit the precious metal ions (gold (III), platinum (IV), palladium (II), and rhodium (Ill)) into metal nanoparticles at room temperature within 120 min. When targeting the leachates from printed circuit boards, the Shewanella bacteria were able to allow selective reduction and deposition of gold (III) ions under acidic conditions in the presence of heavy metal ions, proposing a new bio-recovery system for gold. We also found that the Shewanella bacteria can separate and concentrate soluble rare metal ions (dysprosium (III), indium (Ill), and gallium (Ill)) from dilute solutions. Using this biomass adsorbent, the effectiveness of system for the novel recovery of indium from the leachate of used LCD (liquid crystal display) panels has been demonstrated.IntroductionMany high-tech manufacturing industries are highly dependent upon the use of critical raw materials that are the rare metals (e.g. rare earth elements/indium) and precious metals (e.g. gold/platinum group metals). There are now serious global concerns over the short term and long term availability of critical raw materials for high-tech manufacturing. This highlights the paramount importance of sustainable component reuse and material recycling technologies for recovery of critical raw materials. We believe that the most important domestic source of precious metals is through more recycling, and this will require more research and further development for the recycling of precious and rare metals. In general, chemical/thermal recycling is deemed to be the most appropriate means to extract the precious and rare metals from postconsumer products. However, there are issues related to the heavy use of toxic and hazardous chemicals, and the release of toxic emissions.Biological recovery methods provide an attractive alternative strategy and use microorganisms to separate and concentrate soluble precious and rare metals from dilute solutions into microbial cells via biosorption [1-3] and biomineralization [ 4, 5]. Biological systems generally operate at ambient temperature and near-neutral pH. Consequently, microbial recovery of metals would be an environmentally friendly method for recycling precious and rare metals from end-of-use products."

Jan 1, 2014

By G. O. Oniyide, H. Yilmaz.

"This paper presents the result of the research done on the effect of temperature on the dilatancy of rocks from the Bushveld Igneous Complex (BIC), where the South African Platinum mines are located. The BIC has higher virgin rock temperature (VRT) than the gold mines of the ‘Witwatersrand Basin Complex’. If the platinum mines advance to ultra-deep levels as the gold mines, since the Merensky Reef has been reported to extend beyond 5km, then the virgin rock temperature at 5 km below surface would be approximately 140oC. Hence, there is a need for the investigation of rock behaviour at high temperatures. Five different rock types (norite, leuconorite, mottled anorthosite, pyroxenite and chromitite) were tested in a 2600 kN servo-controlled multi-purpose triaxial testing machine. The tests were done at a constant strain rate of 5 x 10-1 S-1 and a confining pressure of 10 MPa within temperature range of 20 °C (ambient temperature) to 140 °C. The results show a general strength reduction and increasing dilation angles with increasing temperatures. The results also demonstrate that dilation angle is close to the internal friction angle at lower temperatures; however, they are greater at higher temperatures.INTRODUCTIONMany challenges are faced with increasing depth of mining in underground mines. The most obvious are heat, in-situ stresses and those associated with logistics. Issues related to underground heat have mainly focused on the side effect of heat on workers' health, increasing production costs as a result of higher cost of ventilation. The effect of increasing temperature with increasing depth on the behavior of rock has not been given much consideration. Generally, gold mines in South Africa are deeper than the platinum mines but the latter have higher temperature gradient, which makes the platinum mines to be warmer at similar mining depths. Although the study of the effect temperature on the behaviour of rock can be beneficial to both gold and platinum mines, the focus of the research is limited to the platinum mines because of their higher temperature gradient. Donoghue (2004) stated that the virgin rock temperatures (VRT) and air temperatures increase with depth, due to the geothermal gradient and auto-compression, that is, compression of air by its own weight."

Jan 1, 2015

By Dennis McLaughin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine?s Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested 2nd demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

Jan 1, 1981

By G. V. Kalabin

"The paper supports applicability of satellite imagery at regional and local level for rapid quantitative assessment of natural environment in zones of activity of mining complex enterprises. Exacerbation of environmental problems during mineral mining and processing associated with their scale and geography of field distribution through the vast territory of our country requires constant monitoring of natural environment status, which necessitates engagement of space surveillance nowadays. It is proposed to use the monitoring of land cover and land use at regional and local level for the environmental assessment of a particular production or complex productions. You must establish the dependence of NDVI change trend with the magnitude of anthropogenic impact on the source or multiple sources of environmental pollution a particular area.. We present the results of studies of vegetation remote sensing methods in a number of territories placing mining enterprises. INTRODUCTION Ensuring a healthy environment is necessary both in untouched areas and disturbed. The condition of the developed territories should be monitored with particular attention, since the restoration of the disturbed territories requires great efforts and financial costs. More narrowly, the health of the environment (Zakharov V.M. and etc.,2001) means its quality ensuring the health of man and other species of living organisms, which includes two aspects (Zakharov V.M. and etc, 2000): - ensuring an environment conducive to human health as a biological species: - maintaining the health of the natural environment, i.e. its constituent species of living organisms and plants. The consequence is the disturbance of natural ecosystems, which determines the quality of the environment, favorable for human habitation and the state of health of the population in total determine the status of the territories where enterprises for the development of georesources are located and allow them to be ranked according to the degree of environmental danger. Without knowledge of the trajectory of ecosystem successions, it is impossible to offer adequate requirements for the technologies used to ensure the implementation of the preserved natural potential after the removal or reduction of man-made stress."

Jan 1, 2018

By John W. Bell

A FEW years ago the writer had the privilege of examining a piece of apparatus in the Forest Products Laboratory of McGill University which engaged his attention. The Forest Products Laboratory has an excellent installation of wood-grinding machinery, and the officials in charge were naturally interested in acquiring means for estimating the fineness of various wood grinds. The problem was referred to Dr. O. Maass ( l ). Dr. Maass designed a piece of equipment to measure the surface of a wood grind and derived an equation applicable in calculating its value, as follows : After inspecting this apparatus, the writer was disposed to believe that, with some modifications, Dr. Maass' ingenious idea might be utilized to measure the surface of mineral powders. Obviously, some difficulty would be found in maintaining an even suspension of mineral particles of high specific gravity compared to that of wood pulp. The writer will not bore the reader with a description of the various machines built and tried out. Some of these were satisfactory enough to obtain some valuable information, and to bring to light a difficulty which threatened to bring the investigation to an abrupt ending. For the mineral quartz, it was found that Kin the formula above stated was not a constant.

Jan 1, 1944

By D Prior

The Australian mining industry is a significant contributor to the nation’s greenhouse gas (GHG) emissions, and like any industry, it must make efforts to reduce these. Medium- and long-term strategies will include the replacement of diesel engines with alternative energy sources, but what can be done in the short-term to reduce diesel consumption and hence CO2 emissions? Haul trucks are identified as the major contributors of CO2 emissions in the mining fleet and this paper focuses on firstly identifying what drives haul truck emissions and secondly, discussing what is the role of the Fleet Management System (FMS) in reducing these. A key enabler of this is having a robust fuel consumption model within the FMS, and I describe how this may be done. Besides novel approaches to incorporating fuel consumption (CO2) management into truck assignment algorithms, this paper also describes how the FMS can be used to implement and manage procedures and policies to reduce haul truck emissions.

Jun 22, 2022

By Gregory Harbort, Sarah K. DeBono, Alan J. Monaghan, Emmanual V. Manlapig

"The Jameson Cell is a type of flotation machine in which air and pulp are brought together in a vertical tube called a downcomer. Within the downcomer the air and pulp are dispersed into a dense foam of fine bubbles, which creates a favourable environment for bubble-particle collision and subsequent collection of hydrophobic particles. The intense collection zone within the downcomer can be considered similar to the zone between the rotor and stator in mechanical flotation cells.Research into the bubble-particle collision and fluid dynamics of mechanical cells rotor-stator zone has been limited by the difficulty of achieving accurate measurements in production sized machines. With the Jameson Cell the downcomer is largely external and separated from the flotation tank, allowing ready access to the primary contacting zone for measurement and analysis.An investigation has been undertaken into the operating characteristics of the downcomer relating to bubble-particle collision. An effective mapping of the downcomer has been made through measurements of void fraction and bubble size taken across cross sections of the downcomer. Analysis of these measurements has provided an interpretation of the variations in the air and fluid dynamics, bubble size and distribution throughout the downcomer chamber.Existing models of bubble-particle collision efficiency are reviewed in respect to the collected information and refinements conducted. The area of maximum bubble-particle collision efficiency is defined. Findings are related to operation within the rotor-stator zone of mechanical flotation cells."

Jan 1, 2003

By Paulo Chaves, Márcia Gonçalves, João R. S. Carvalho, Fernando J. A. S. Barriga, Edgar Carrolo, Tiago Luna, Ricardo Rato, Anabela Bento

INTRODUCTION For the last decades, deep-sea marine resources such as seabed massive sulfides (SMS), polymetallic nodules and ferromanganese crusts (Fe-Mn crusts) have received an ever- increasing amount of attention worldwide for their abundance in critical metals and potential commercial value. This interest has mostly been driven by the growing world demand for raw materials, in particular for high- and green-technology applications (e.g., hybrid and electric cars, batteries, photovoltaic solar cells, cell phones, super magnets), as well as by industrialized countries governments other than BRICS states need to secure a more diversified supply of metals, resulting in a new deep ocean exploration boom. Since the oceans and its resources are increasingly seen as indispensable for humans needs and their challenges in the decades to come, this boom increments pressure on marine areas, either in international or within countries economic exclusive zone (EEZ). Since 2002, the International Seabed Authority (ISA) has signed up 29 contracts with several entities and national governments from multiple countries (e.g., Japan, China, Germany, France, Russia, India, Rep. of Korea, UK, Canada, Brazil) for exploration for deep-sea mineral resources in international waters, either for scientific or commercial proposes, which together cover over 1.3 million km2 [1]. In turn, over 300 exploration licenses, covering more than 650,000 km2, have been granted within the EEZ of Pacific countries such as Papua New Guinea, Tonga, Fiji, Solomon Islands and Vanuatu [2, 3]. This number is expected to increase very rapidly, as 77 countries have proposed to the United Nations the extension of their continental shelf in order to extend their EEZ and jurisdiction over potential deep-sea mineral resources [4]. Its estimated that 42% of the potential areas for SMS occurrences, 54% for cobalt-rich Fe-Mn crusts, and 19% for polymetallic nodules lie within the EEZ of coastal countries [5]. In addition, a huge amount of seafloor is yet to be explored and evaluated. Combined, the size of the granted exploration areas represents less than 10% of the overall area thought as most favorable for the occurrence of the 3 types of deep-sea mineral resources above mentioned. This means that today’s assessments on deep-sea mineral resources are only a rough approximation.

Jan 1, 2018

By Vittorio Manassero, Antonello de Risi, Filippo Cavuoto

"This paper deals with an innovative mechanized method to bore and simultaneously line circular shafts, adopted in the Naples Metro project for the installation of 10 vertical shafts for ventilation purposes. With this method, excavation of shafts is carried out under a positive head of stabilizing fluid by a milling machine, temporarily set at the bottom of a permanent lining made of precast reinforced concrete segment rings. The debris is evacuated by inverse fluid circulation. The shafts in Naples are 4.5 m I.D., from 34 to 44 m deep and they are all located downtown in a highly urbanized area. They were bored and installed into volcanic soils under a hydrostatic head of up to 30 m. Displacements and groundwater level were constantly monitored to keep control of the effects on the surrounding buildings and utilities. INTRODUCTIONThe extension of Metro Line 1 in Naples (Italy) from the previous terminal of Piazza Dante to Piazza Garibaldi is also called the “low stretch”. Most of it runs along the coastline, encompassing the historical city center, the Greek-Roman Neapolis. The Metro Line crosses under densely urbanized areas for the whole way (Figure 1). It runs beneath Via Toledo, which follows the layout of the ancient Aragonese walls. The first station (Toledo) is located halfway along this street. Then, after a wide bend, the line reaches Piazza Municipio, where the second station is located. From there, the line moves along the axis of Via Depretis and Corso Umberto I, where the stations Università and Duomo are situated. The fifth station is in Piazza Garibaldi and the end of the stretch is located at the Naples Business Center. The twin single track tunnels were bored into volcanic tuff by TBM. This design choice simplified by far the construction of the tunnels and reduced to practically zero the interactions between tunnelling and surface buildings and utilities. Nevertheless, this choice entailed that the line had to be located at depths to the order of 35-45m below ground level and 30-35m below the water table. At each tunnel segment between stations, a pair of ventilation chambers were constructed (10 in total). Each ventilation chamber is connected to one TBM tunnel by a vertical shaft and a horizontal drift at the base of the shaft. The shafts, in addition to tunnel ventilation, provide a safety access/escape."

Jan 1, 2016

By Thomas Fraser

WHEN the Bureau of Mines initiated the program of large-scale research and development in the field of synthetic liquid fuels authorized in the Synthetic Liquid Fuels Act of April 5, 1044, the Coal Preparation Section was assigned the task of obtaining data on the preparation characteristics of the coal in large reserves that might be adaptable to use in this new industry. It is natural that, as the rapidly developing general research program brought about new concepts of raw-material quality, preferred geographical location, and the like, the orientation of coal-preparation investigations should have undergone some change. The first major assignment was the sampling and testing of a series of typical American coals deemed to he suitable for hydrogenation based on early research work conducted by the Bureau of Mines. This first series of tests has been completed and is reported in this paper.

Jan 1, 1950

The intent of this manual is to provide guidelines for inspectors of drilled shaft construction otherwise referred to as drilled piers, caissons or bored piles. It should also be helpful to train beginning geotechnical engineers with limited first hand experience or for geotechnical engineers who are training inspectors. It is expected that the general guidelines and procedures described here will be supplemented by local geotechnical engineers working in a particular region based on local practice and experience. Since drilled shaft construction procedures vary widely based on local geology and size of project, an all-inclusive manual is not considered practical. This manual focuses on traditional topside inspection for routine drilled shaft construction. Other inspection and evaluation methods that rely on electronic equipment are available, but these methods require extensive training and experience in the interpretation of results. These more sophisticated methods of drilled shaft inspection and evaluation are common in construction, but they are usually provided by specialty subconsultants. The subconsultant will typically submit a report for each shaft, which will be reviewed by the geotechnical engineer. Other manuals are available to describe the electronic methods of drilled shaft inspection.

Jan 1, 2004

By Jan M. Mutmansky

"When, in 1973, a limit was placed on the amount of dust in the coal mine atmosphere, restricting the average exposure of a coal miner to 2 milligrams of dust per cubic meter of air (mg/m'), skeptics in the United States and abroad Said the standard could never be achieved. They cited much more lenient standards already established in other countries and refused to believe that the United States could meet the world's most stringent requirements in mines where dust had never before been regulated. Yet 10 years later the goal had largely been achieved and miners were working underground in a cleaner atmosphere than ever before. It was a major achievement and a big stride in what had become a war on coal workers' pneumoconiosis (CWP), the black lung disease prevalent among miners in underground coal mines.Although the health hazards caused by working in a dust-filled mine atmosphere have long been recognized, the problem became particularly acute in this century with the mechanization and increased productivity of underground coal mining. The United States was much slower than some other countries to address the problem of respirable diseases among miners. While dust levels in South African gold mines were first regulated in 1912, in the United States it was only when 476 workers died of silicosis while blasting a tunnel through a mountain near Gauley Bridge, West Virginia in the 1930s that widespread public attention became focused on the plight of workers in dust-filled environments. Another 30 years passed before regulation of dust finally became law in the Coal Mine Health and Safety Act of 1969.With a stringent new standard imposed in all underground coal mines, the industry was faced With the daunting problem of reducing levels of airborne dust from perhaps 6.5 mg/m' to 2 mg/m', in an inherently dusty operation carried out in the close confines of underground passageways. Most of the coal dust is made by the cutting operation in which the continuous miner or longwall machine can produce several thousand milligrams of respirable dust for each ton of coal mined. Other dusty operations such as drilling holes for roofbolts, loading and unloading coal on shuttle cars, and the operation of conveyor belts contribute to the overall problem.Since the institution of the new dust control standards, a number of strategies have been adopted for reducing the coal dust in the mine atmosphere. These strategies involve engineering and design improvements that help lo prevent the generation of particles, keep particles of dust from becoming airborne, carry dust away from the working area, and isolate the dust from the workers in the mining operation. These procedures have been pursued vigorously by the Bureau of Mines, and many successful methods have been developed to reduce the mass concentration to which the workers are subjected. The mining companies were reluctant at first to confront the problems but after a period of trials and gradual improvement, they joined with others in the fight to reduce the dust concentrations in the working place."

Jan 1, 1990

By J. G. LECKIE

During the first ten months of 1943 copper was produced at a higher rate than in 1947. However, on Oct. 24 one of the large mines was shut down due to a strike. As of Dec. 31 the strike was still in effect and had already resulted in a loss of production of 50,000 tons of copper. The demand for copper was considerably greater throughout the year than the supply. The price of electrolytic copper delivered at the Atlantic Seaboard refineries advanced from 21.20 to 23.20 cents per lb during the year. This sustained demand for copper, together with the increase in price, has had the natural effect of spurring interest in uncovering new deposits, and in re-examination of known low-grade deposits and old tailing clumps. This is in addition to the usual reevaluation activities which normally result from the constant improvements in efficiency of ore concentration.

Jan 1, 1949

By V. Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Apr 1, 2004

By Steven Keim, Steven Stansfield, Kevin Andrews

Geotechnical, geological, and hydrogeological fieldwork and data collection for the mining industry is often conducted by younger, less-experienced staff members. In many cases, fieldwork personnel are recent college graduates or are otherwise relatively new to the mining industry. Due to busy schedules, staffing shortages, project budgets, and in some cases, poor management, new fieldwork hires often do not receive thorough training. In the past and the present, many workers in the mining industry learn(ed) by “doing.” While this is still considered to be the most practical approach and the easiest way for a company to determine the skill set of an employee, there is always some risk involved in the “feet to the fire” method. The reality is that field personnel are often collecting data on which major operational decisions will be made or on which regulators will base enforcement decisions. Inadequately trained or inexperienced field personnel may collect inaccurate data or fail to recognize key conditions that may influence decisions made by regulators, design engineers, mine managers, and corporate leaders. Even the best engineers may come to incorrect conclusions if they are starting with poor input data. Decisions based on inaccurate data often result in delays, budget issues, unsafe conditions, or even worse consequences. This paper provides numerous mining industry examples of incidences where inaccurately collected field information did, or could have, resulted in major adverse consequences. The paper also offers some simple approaches to minimizing the potential for such problems.

Jul 1, 2023

By David M. Cregger

The performance of the nation's first geologic repository for Commercial High Level Waste will be evaluated in a variety of ways which will involve the use of the state-of-the-art thermomechanical computer codes. Elastic properties of the host rock and the materials surrounding the repository are required for this numerical modeling effort to assess both near- and far-field effects. Only limited laboratory testing is possible, however, making it extremely beneficial to expand the data base by calculating dynamic elastic properties from available geophysical well logs. Elastic theory dictates that for an isotropic solid there are only two independent variables in addition to mass density, namely the compressional velocity, the shear velocity, and Poisson's Ratio. Compressional velocity and density are readily measured by geophysical well logs or in the lab; the crux of the solution requires measuring or determining either the shear velocity or Poisson's Ratio. Examination of acoustic propagated shear waves measured during confined compression testing demonstrates that Poisson's Ratio is a fundamental lithology-dependent parameter. Once a rock mass is appropriately classified, application of the laboratory derived dynamic Poisson's Ratio will yield a continuous and reasonable in situ modulus from acoustic and density logs. For preliminary characterization and assessment of the mechanical properties of rocks within the subsurface, and for studies of rock quality, this method is sufficiently accurate. The general availability of acoustic and density logs from wells logged for other purposes has made the application of this method desirable.

Jan 1, 1984

By Pia-Maria Haselberger, Marc Schiemann, Christian Frühling, Nicolas Richter, Hendrik Wehner, Andreas Kaschube

"The paper provides the principle considerations for a novel vehicle class within the scope of the project Large Modifiable Underwater Mothership (MUM). The main idea for these ships is to create a highly modular building block system for the global layout. This building block system allows for a mission-dependent module assembly. For the purpose of deep sea mining for example, the range of tasks reaches from multipurpose transportation and exploration missions to supporting tasks in up to 5000 m depth, e.g. energy supply. Topics covered in this paper are related to potential missions for these vehicles, the modular layout and the structural layout of a separate block module. The paper closes with a conceptual design example for this class.Index Terms—MUM, UUV, underwater mother ship, autonomous underwater vehicle, modular, deep sea, conceptual designI. INTRODUCTIONAs one of the leading economic nations, Germany is in need of energy and raw materials. In the 21st century, marine resources are a prominent and promising alternative to land based resources. However, there are challenges that need to be considered. Rough and often poorly plannable weather conditions prevail distant to the marginal seas. Ice coverage makes offshore services inefficient and costly in Polar Regions. The average ocean depth of 3500m and the associated environment conditions cause difficulties in fulfilling tasks in the deep sea. The project Large Modifiable Underwater Mothership (MUM) [1] will enable more efficient solutions in order to accomplish undersea duties and services in harsh conditions.This joint project comprises workshares from Atlas Elektronik, EvoLogics, thyssenkrupp Marine Systems, the University of Rostock and the Technische Universität Berlin. The principle idea of the project is the conception of a novel vehicle class. With highly modular autonomous underwater vehicles, this class will be capable of undertaking a variety of different tasks. Classically engineered vehicle structures will be split into single basis modules which can be flexibly assembled with specialized mission modules to form potent systems for individual assignments. The group of basis modules consists of units for navigation, vehicle control, propulsion and energy generation via fuel cell technology. The potential reusability of system relevant modules leads to a significant cost reduction and to shortened development periods compared with conventional vehicle concepts. The integration of newly designed additional mission modules is possible with little effort and a separate commercialization of single modules is feasible."

Jan 1, 2017

By E. T. Tuzcu

In this manuscript, a new approach for modeling the rate of grinding process is explained. A review about grinding rate definitions so far is given and the possible ultimate way for grinding modeling is given as modeling the rate based on energy spectra. The traditional/phenomenological approaches for modeling size distribution of grinding mills give their place to a new generation modeling technique. Developments in the computational methods and necessity to model product size distribution of large mills, larger than ball mill size, paved the way for this novel technique. The traditional grinding rate models are mostly based on the back calculated breakage parameters from the experimental data. However, direct modeling of breakage parameters and hence the prediction of size distribution of the grinding mills may become possible with this approach. The material breakage data and discrete element method (DEM) energy spectra are the main components of this approach. Albeit the focus in this study is on modeling of breakage rate under impact mode of breakage, the abrasion mode of breakage was also tested by carrying out abrasion tests. Impact mode of breakage was analyzed using ultra-fast load cell device (UFLC) and drop weight tester. Dry tumbling test was carried out for abrasion experiments. Obtained material breakage versus energy data are combined with the collision energy spectra to obtain the breakage rate function. In addition, the material breakage versus energy information from the tests is converted into breakage distribution function. The model was verified in a lab scale mill (90 cm diameter-15 cm length). 10 to 15 kg of limestone was ground using 50 mm steel ball at varying conditions, i.e., rpm, volume loading. It is shown that the proposed model predicts all (1, 2, 4 min.) grinding intervals for all experiments highly accurate.

Sep 1, 2012

By Jianjun Tian, Changjiu Zhang, Chunmin Wang

Two lines of single stage autogenous milling circuits have been installed and commissioned as the primary grinding process for the Sino Iron project where magnetite ore is treated to produce iron concentrate via magnetic separation. Various challenges were encountered during the commissioning and ramp up stages which are discussed in the paper and include treating a highly competent ore in a closed circuit AG mill, operating the largest mills in the world and dealing with a number of engineering issues related to plant operability. Details of how these challenges were overcome are described as well as the observed operating characteristics of the mills and their optimisation through rigorous study, simulation and successful solution implementation. Further potential improvement opportunities are also discussed as part of the ongoing technical program at site.

Jan 1, 2014