Search Documents

By T. E. Gray

This report describes the preparation characteristics of the more significant coalbeds in Monongalia County, W. Va. It is one of a Bureau of Mines series planned to determine coals suitable for producing metallurgical coke, either as mined or after beneficiation. Over 9.5 million tons of coal was produced in Monongalia County in 1957, of which more than 7 million tons was cleaned mechanically in 8 cleaning plants. On January I, 1954 the Bureau of Mines estimated that 1,576 million tons of recoverable coal remained in the county in beds 28 inches or more thick.

Jan 1, 1960

By P. Cheung, J. Gulyas, R. Clary

Over the past 50 years, the use of autoclaves in the metallurgical industry has evolved from final metal recovery (hydrogen reduction) and purification (sulphide precipitate oxidation) to treating whole ores and concentrates. Recent process developments, such as the use of autoclaves for laterite leaching, have necessitated higher temperature and pressure operations, which in turn have seen marked advancements in technology and manufacturing capabilities to keep in step with process demands. This paper will discuss the advances in technology in terms of design, materials and construction of autoclaves and liners, typical dip tube design and geometric layout. This paper will also address specific auxiliary equipment, such as acid and steam injection systems, and components, such as agitator seal systems.

Jan 1, 2004

By Jessica M. Wempen

"Differential Interferometric Synthetic Aperture Radar (DInSAR), a satellite-based remote sensing technique, has application for monitoring subsidence with high resolution over short periods. DInSAR uses radar images to measure centimeter-level surface displacements. In the images, ground resolution can be relatively high, with each data point (pixel) representing the average displacement over an area of several square meters. The image data are acquired regularly which allows subsidence to be monitored sequentially over short periods; imaging periods typically range from weeks to months.Monitoring subsidence over short periods with high spatial resolution has potential to provide insight into the dynamics of subsidence and into relationships between mine advance and subsidence. In this study, for three longwall mines in the western United States, initial subsidence occurring at the start of longwall advance is quantified over short periods (12 to 72 days). C-band interferometric wide swath Synthetic Aperture Radar (SAR) images from the Sentinel satellites are used to quantify the subsidence. Overall, the data show initial development of subsidence, expansion of the subsidence trough, and the advance of subsidence in the direction of mining.INTRODUCTIONApplied Differential Interferometric Synthetic Aperture Radar (DInSAR)Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique that can be used to quantify small displacements of the Earth’s surface. Using data from the Seasat satellite, which was launched in 1978 (Jet Propulsion Laboratory, 2018), studies by Goldstein, Zebker, and Werner (1988) and by Gabriel, Goldstein, and Zebker (1989) applied Synthetic Aperture Radar (SAR) interferometry to topographic mapping and displacement monitoring. These studies established the potential for broader applications of radar interferometry. Studies by Foxall, Sweeney, and Walter (1998), Wright and Stow (1999), and Carnec and Delacourt (2000) represent some of the earliest evaluations of DInSAR for mine subsidence monitoring. All three of the studies demonstrated the application of DInSAR for quantifying mine subsidence. They also demonstrated difficulty accurately measuring subsidence over long periods due to data decorrelation. DInSAR continues to be evaluated as a tool to quantify surface deformation related to active and historic mining. For example, see Vervoort and Declercq (2018), Wempen and McCarter (2017a), Chen et al. (2013), and Liu et al. (2013). Technologies associated with SAR interferometry continue to develop. Recently launched satellites have relatively high spatial and temporal resolutions, and data processing methods and data accessibility are improving."

Jan 1, 2019

By Changshou Sun

The geotechnical properties of mining zones at Leeville Underground mine (or simply called Leeville mine through this paper) are different from one zone to another. The typical ground condition is poor to very poor. Therefore, an appropriate ground control practice is the key for the successful and smooth ore production at Leeville mine. Based on the available geotechnical data, the empirical and numerical methods are used to design the right ground support systems. The main ground control practice at Leeville mine includes geotechnical data collection, evaluation of the stiffness of the support system, selection of rock bolt types, design bolt length and bolting patterns, development of the ground support standards, and performance of quality controls on bolt installation to ensure proper rock anchorage, and strength of shotcrete and backfill. Through all these activities, an appropriate ground support system has been established and applied at Leeville mine for the past four years. So far, a good result related to successful ground control and smooth ore production has been achieved, although the system is still being improved. The authors of this paper will summarize the ground control practice conducted in the last four years and will discuss the procedures and standards of establishing the appropriate ground support systems for Leeville mine.

Jan 1, 2013

By K. Perry, R. Eades

"Highwall miners continue to be implemented by operations to increase recovery, improve margins, and justify higher stripping ratios as high quality surface reserves become increasingly rare. Many times, operations facilitate projected underground operations by leaving an intact highwall for development purposes. These facts result in larger highwalls that are left standing for increased periods of time prior to reclamation. As a consequence, worker exposure and risk is also elevated, resulting in higher potential for accidents or fatalities relating to surface highwalls. Highwall stability is a complex issue, dependent on both geologic and mining factors. Dynamic numerical modeling offers the capability to assess possible stability issues related to blasting-induced ground vibrations. Research has been conducted to evaluate the effect of highwall stability due to ground vibrations from blasting events. Additionally, the relationship of amplitude and frequency, and their impact on highwall stability is investigated. The results of this modeling indicate that amplitude has little impact on stability. However, frequency has a significant impact on highwall stability. INTRODUCTION The number of mining fatalities has declined since 2010, and 2016 is currently on pace to continue this trend (MSHA 2016). This decline can be directly correlated to the decline in surface mining activity and the overall decline of the coal industry. However, since 2002 the percentage of surface coal mine fatalities associated with highwall activities remains relatively high, constituting approximately 15% of all surface mine fatalities. 2014 was the first year with a highwall failure fatality since 2011. Most recent surface coal mining fatalities are associated with machinery and haulage. Table 1 provides a summary of the total surface coal mining fatalities, and the number of highwall failure fatalities dating back to 2010.Highwall stability is a complex issue, dependent upon geology and geologic discontinuities within the rock mass, along with highwall geometry, standing time, and applied stresses. Another possible concern that has not been previously investigated is the effect of blasting-induced stresses on highwall stability and the stability of web/barrier pillar systems as a result of ground vibrations from blasting events. Many modern surface coal mines employ numerous extraction fronts that rely on blasting for primary rock breakage. This results in highwall and highwall pillar systems experiencing blasting-induced stresses of many different types and magnitudes."

Jan 1, 2017

By R. Robertson

Dense medium cyclones are the preferred means for cleaning 112 in. x 14 Mesh to 28 Mesh (12.7 mm x 1.0 mm to 0.6 mm) raw coal and are becoming a common choice for cleaning raw coal from a nominal top size of 2-1/2 in. to 3 in. (63.5 mm to 76.2 mm) down to 14 Mesh to 28 Mesh (1.0 mm to 0.6 mm). During the last ten years, dense medium cyclone circuitry design has undergone changes which have combined to improve process efficiency. This paper describes these improvements and compares present day design with the design used prior to the mid 1980's. Improvements in the following areas are described: Raw coal desliming, cyclone configuration, drain and rinse applications, dilute medium circuitry, and instrumentation and control.

Jan 1, 1997

By H. Hejny

Economy needs mineral raw materials in almost each sector of modern life. They can only be provided by mining activities. An increasing share of the total mining production will be by underground mining. The mineral deposits will be found at gradually greater depths, including all problems associated with them. It involves an increase in overburden pressure with subsequent rock stability problems and risks of structural collapse. There is a need for new and safe technologies for almost all parts of a modern mine. The mining industry faces a number of challenges which require technical solutions that encompass the entire network and include the economic, social and environmental issues. The industry needs a new image based on pioneering solutions and a modern structure that can exploit minerals at greater depths and promote both high productivity and safe working conditions. Funding has been secured from the European Commission for the I²Mine project. Work started in November, 2011. This initiative is designed to focus on the technological challenges that the mining industry is currently facing including the exploitation of ever deeper deposits and the aspiration for an invisible, safe, zero impact mine. The project comprises a consortium of 27 organisations from 10 European countries. I²Mine marks the start of a series of development activities aimed at realising the concept of an invisible, zero impact, deep mine. The extractive sector, still seen as being old fashioned and environmentally unfriendly, will show that mineral extraction and processing can be done in a highly innovative and sustainable manner with low impact underground and zero impact above ground. The concept of I²Mine is to develop innovative methods, technologies, machines and equipment necessary for the efficient exploitation of minerals and disposal of waste, all of which will be carried out underground. This will dramatically reduce the volume of surface transportation of both minerals and waste, minimising above ground installations and reducing the environmental impact. New eco-efficient technologies will be applied in order to make the entire mining process more efficient and environmentally sound. The concept is for an integrated mine, with the majority of the installations underground, and only the final product will be transported above ground to be shipped to the customer. Production waste will be treated and stored underground and gaseous emissions will be managed underground as far as practical. I²Mine will also focus on ideas and concepts that increase energy efficiency and decrease waste. The core of the project will be to develop breakthrough technologies for autonomous, highly selective, continuous mineral extraction processes and machinery based on new sensor technologies, face front separation as well as innovative concepts for mass flow management and transportation integrating state of the art technologies. The concept of an invisible, zero impact mine requires a refined process underground that selectively extracts the mineral thereby reducing waste. For this reason, improved extraction machines and near to face processing methods, including backfill procedures, need to be developed. These developments include rock mechanics and ground control solutions, incorporating health, safety and environmental issues.

Aug 1, 2013

By J. R. Thoenen

This circular is part 2 of the third subject (entitled "Excavation") of a series summarizing; the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes. This paper discusses the use of the power scraper, slackline cableway excavator, and hydraulic monitor, and part 3 will discuss the use of various types of dredges. Subsequent papers in the series will discuss the use of haulage equipment, the application of both excavating and haulage equipment to various types of deposits, and operating costs. THE POWER SCRAPER The power scraper is a younger member of the various forms of gravel excavators. It is a mechanized enlargement of the slip scraper and other scrapers which depend upon animals for power and has a greater range of operation from a single set-up than any other excavation unit except the slackline cableway excavator.

Jan 1, 1935

By A. L. Hinde

The steady-state and dynamic behaviour of semi-autogenous grinding (SAG) mills are arguably best described using a population model that caters for the breakage kinetics and the material trans-port of rock and pulp inside the mill. Breakage kinetics are usually expressed in terms of a specific breakage rate function and a separate primary breakage distribution function. Material transport usually invokes the concept of a specific discharge rate function. Unfortunately, the breakage rate and breakage distribution functions for SAG mills are very difficult to estimate uniquely from plant data alone. Simplifying assumptions must be made to over-come this problem, which leads to many unresolved dilemmas with regard to whether or not the de-rived functions are accurate, precise, and reflect reality. For example, it is sometimes assumed that the breakage distribution function for a SAG mill treating run-of-mine ore can be derived from laboratory dropweight and tumbling tests on small rocks in narrow size ranges. Such tests hardly reflect the environmental conditions likely to be encountered in a pilot or production SAG mill where there is a wide spectrum of particle sizes. It is shown that the dilemmas associated with standard population balance models (models that utilise separate breakage rate and breakage distribution functions) can be overcome by expressing breakage behaviour inside a SAG mill in terms of a single function. This function is an energy-based cumulative breakage rate function defined as the fractional rate at which particles and rocks coarser than a given size break to below that size per unit specific energy input. A model for SAG milling is formulated, which invokes the concept of a cumulative breakage rate function. Comparisons are made between the mathematical structure of this ?simple model? and standard population balance models. Perhaps the most attractive feature of the ?simple model? is that the cumulative breakage rate function can be uniquely estimated from measurements of size distributions and mass flows of the feed and discharge streams together with the size distribution and holdup mass of the mill charge. Such measurement can easily be made at pilot scale. It is concluded that this simplified approach to SAG milling may turn out to be the quickest way to fully describe and quantify the performance of these very complex mills.

Jan 1, 2014

By John L. Sundstrom

Complete systems were designed -and are in operation to recycle the effluent streams and to remove impurities from tankhouse. electrolyte, Heavy em¬phasis was placed on making usable products from as many streams as poss¬ible at minimum capital and operating costs. Almost complete recycling: and reuse of water and sulfuric acid were paramount. Techniques used in-clude solvent extraction - electrowinning, evaporation - crystallization and filtration.

Jan 1, 1992

By G. W. Barton

Process Systems Engineering (PSE) can be defined as the integrated usage of computer-based design and analysis tools. As such, PSE is becoming increasingly important in the chemical and petrochemical industries. This paper shows how a range of PSE techniques have been applied to the zinc electrowinning process. Topics discussed include model development, parameter estimation, steady-state and dynamic model applications, steady-state optimisation and neural network modelling.

Jan 1, 1994

The Boliden Aitik concentrator in Sweden processes 2,000 tph of low grade copper ore. The plant consists of five grinding lines feeding four bulk flotation banks with a scavenger concentrate regrind mill, and a column cleaner circuit with a regrind mill. The authors installed a model-based expert, optimizing control system to maximize copper recovery in the bulk flotation circuit while maintaining an appropriate copper grade in the cleaner feed. The optimizing control system uses on-line assays and calculates and implements set points for cell pulp levels, air rates and reagent addition rates. It combines the power of a dynamic population balance model which estimates mineral liberation in each stream, an optimizer which computes appropriate set points and a rule-based module which implements the strategy. The benefits have been evaluated over three months. The model-based expert, optimizing control system generates a measurable increase in copper recovery, around 0.5 per cent and an optimized bulk concentrate grade. The need to maintain the optimizing control system and other practical aspects are discussed.

Jan 1, 1998

By M Hawkins

The Clem Jones Tunnel (formally known as the North-South Bypass Tunnel), a A$2.88 billion road tunnel project in Brisbane, Queensland, was successfully completed almost seven months ahead of schedule. The project included two parallel 4.7 km long road tunnels, 740 m of intermediate roadway access ramps and two auxiliary ventilation tunnels. The tunnels incorporate intelligent tunnel systems, best practice fire and life safety standards and typical civil tunnel elements.Over the duration of the project the Parsons Brinckerhoff (PB) and AECOM (formally Maunsell) design joint venture (MPB) were Lead Designers to the Leighton Contractors and Baulderstone Bilfinger Berger Joint Venture (LBBJV). Construction of the toll road commenced in September 2006 and was completed in March 2010, with the tunnel opening then. Contributing to the success of this project was the continued support the lead designers gave throughout the construction period.This paper will focus on some of the structural elements that contributed to the success of the project – in particular the cable tunnel structure, a small precast, culvert shaped element under the pavement of the mainline tunnel, and the fit-out of the Gibbon Street shaft which were designed to be constructed in a combination of precast and in situ concrete.The cable tunnel was incorporated early in the design phase and runs the length of much of the tunnel. This paper will outline the challenges faced by the designers with implementing this system which provided significant construction advantages, among which were being able to install a separate ventilation duct during construction and to start fitting out the mechanical and electrical conduits and drainage system while tunnelling was still underway.The Gibbon Street shaft had a length and width of 20 m by 40 m and an overall depth of 38 m. A 20 m high structure of precast and in situ concrete was constructed in the base to accommodate mechanical and electrical equipment and provide a take-off access for the southern ventilation tunnel. The construction purpose for this structure was to provide a junction between the tunnel boring machine (TBM) and the roadheader-style tunnels, a staging platform for commencing the roadheader tunnelling, and a platform where the TBMs could be dismantled and removed.The design was assessed and reviewed many times throughout the construction process to address the needs of each of these stages. Innovative use of precast concrete was used to minimise construction time.Additionally, the designers provided support to the construction team from the time of design completion through to the tunnel opening. This meant that the changes to the design and adjustment of construction loadings could also be assessed. The fi nal outcome resulted in an efficient construction sequence and a project that has provided an excellent outcome for the client, stakeholders and community.

Mar 8, 2011

By D. K. Mynear, J. S. Gardner, S. Mittle, A. A. Campoli

West Virginia, although having adequate solar insolation, has witnessed very little actual solar development to date. The reasons for this lack of development are varied, but the primary obstacles to future development appear to be the absence of state-level policies and regulations promoting growth in the solar industry. West Virginia possesses large tracts of under-utilized land throughout the state created by previous mountaintop mining operations that could theoretically be re-purposed for solar farm development. Accomplishing this task will require not only revisions to the current legislation, but also acceptance by utility companies, landowners, and mining companies. Solar developers will need confidence that they can secure revenue from the electricity and Renewable Energy Certificates (RECs) generated by solar projects. Additionally, solar companies will need assurance they will be protected from any non-related environmental liabilities that could arise in the future. The primary avenue in bringing significant solar development to West Virginia will come through large corporate clients demanding or partnering with utility companies for incorporation of solar options into their energy portfolio to help meet established sustainability goals. This scenario has been witnessed in other states where a large client demands renewable options. Solar development could also represent a means through which mine operators might alleviate some of their reclamation and bonding obligations; where the landowner could supplement income from their underutilized land holdings; and where displaced miners could be repurposed in solar installation/maintenance jobs. Utilizing data from the West Virginia Permit Database, this report identifies several mine sites that hold potential for solar development in the future. INTRODUCTION The diversification of energy sources in the United States (US) has seen major shifts during the past decade resulting from: • A sudden abundance of low-cost natural gas becoming available through advanced horizontal drilling and hydraulic fracturing techniques. • Incentive-driven policies leading to new development in alternative energy. • The emergence of renewable energy sources, proliferated by state and federal level incentives and falling capital costs. Coal was once the primary low-cost fuel source for the generation of electricity in the US for most of the last century, providing approximately 50 percent of the total production capacity. However, within the past decade lower-cost natural gas has overtaken coal as the primary source of fuel used in electricity generation, and renewable sources have steadily grown to account for approximately 10 percent of the overall mix.

Jan 1, 2019

By G du Toit, P L. Gillot, M Swanepoel

Randgold Resources’ Loulo-Gounkoto Complex is one of the largest gold mining operations in Mali, West Africa. The mine, which is situated on the western border with Senegal, treats more than 4 Mt/a of ore through a conventional three-stage crushing and ball milling circuit followed by a carbon-in-leach plant. Ore supply is achieved by a combination of open pit and underground mining, with the majority of the ore supply sourced from the Gara and Yalea underground mines situated approximately 2 km and 6 km respectively from the gold plant.In 2011, Randgold Resources commissioned Golder Associates to perform an evaluation study for providing structural backfill to both the Gara and Yalea underground mines using the current gold plant tailings. The test work performed as part of the evaluation study concluded the need for a tailings cycloning and dewatering facility capable of producing slurry at a solids concentration of 65 per cent with a particle size distribution that had minimum 25 per cent passing 20 µm and less than 5 per cent of -5 µm material. Tailings desliming was required to ensure a consistent feed quality to the paste preparation plants and to ensure that the system would be capable of handling variation in the feed composition from the gold plant.WorleyParsons, previously TWP Projects, was contracted by Randgold Resources to complete the engineering design for the slurry preparation plant, whilst Golder Associates was retained to complete the engineering design of the two paste preparation plants.This paper discusses the test work, design considerations and engineering design of the slurry preparation plant, termed the ‘intermediate plant’, as well as all ancillary facilities required for the delivery of the deslimed slurry to the paste preparation plants located at the two underground mines.CITATION:Swanepoel, M, du Toit, G and Gillot, P L, 2014. Case study – engineering design for a slurry preparation plant for a paste application in West Africa, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 477–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By F Tang, Ö K. Büyükuslu, M Baben, S Petersen

GTT-Technologies’ ChemApp for Python was developed to provide a powerful, easy to use interface to ChemApp for a programming language highly popular with scientists and engineers. It is used, for instance, by GTT to develop program modules such as the CALPHAD Optimiser for the FactSage™ software, by customers to move from interactive FactSage calculations to perform versatile scripting with Python, and by GTT and its partners in research projects in the area of materials informatics. Computational thermochemistry is fundamental for advancing sustainable metallurgy and creating new alloy compositions for engineering applications. Materials informatics involves handling vast amounts of data and complex workflows. GTT’s approach uses ChemApp for Python and the FactSage thermodynamic databases to design recyclable alloys from the start, incorporating a higher percentage of scraps while aiming to simplify the workflows to simulate material design steps. Challenges arise due to recycling scraps, introducing more elements for consideration. CALPHAD-based databases accurately cover materials from primary metallurgy, but additional data for minority and critical elements is crucial for precise computational modelling. GTT combines machine learning-based ab-initio databases with traditional CALPHAD databases to cover the complete chemical space with appropriate accuracy. The design of a hardfacing alloy through a high-throughput materials informatics approach is used as a demonstrator of the current possibilities.

Jun 19, 2024

By John Richards

MY remarks will be confined to the experience of our company in mining the No. 8 seam of coal in Ohio, although I believe that the relationship existing here between the method of mining and the method of cleaning will hold true in many of the coal seams throughout the country. The increasing demand for a cleaner and better graded product is being felt throughout the entire coal industry, and the methods of mining are playing an important part in the control of various sizes and quality of coal produced. We have found a definite relation between the mechanical loading of coal and its preparation for the market. In the No. 8 coal seam the location of the non-combustible material is regular. The' marketable coal lies in three benches, separated by streaks or bands of impurities. These impurities must be removed from the coal to properly pre pare the product for the market. Where hand-loading methods are employed, the loader removes as much of this non-combustible material as possible at the working face. The impurities that are missed by the loaders are removed as the coal passes through the preparation plant, by means of picking tables. As this method of cleaning cannot improve the quality of the extremely fine sizes, a practice has been established in the company's hand-loading mines, of undercutting the coal about 2 in. above the bottom of the seam, thereby eliminating any possibility of impurities caused by the cutting machines cutting into the rock bottom below the coal seam.

Jan 1, 1934

By J. D. Swanepoel, S. Horn, C. J. Badenhorst

Diesel particulate matter (DPM) is the particulate component of diesel exhaust, which includes diesel soot and aerosols. When released into the atmosphere, DPM can take the form of individual particles or chain aggregates, with most in the invisible sub-micrometer range of 100 nanometres. The main particulate fraction of diesel exhaust consists of fine particles and because of their small size, inhaled particles may easily penetrate deep into the lungs. The rough surfaces of these particles make it easy for them to bind with other toxins in the environment, thus increasing the hazards of particle inhalation. DPM is a significant health hazard in underground mining operations, where the use of dieselpowered equipment in confined spaces can lead to high levels of exposure among people working in these environments. Classified as a carcinogen by the International Agency for Research on Cancer (IARC), DPM has been linked to severe health effects, including respiratory and cardiovascular diseases, as well as an increased risk of lung cancer. Effective management of DPM is essential not only for protecting people’s health but also for ensuring regulatory compliance, maintaining operational efficiency, and safeguarding the long-term viability of mining companies.

Mar 5, 2025

By C. Steve Albrecht

The primary objective of this study is to "evaluate the influences of different equipment systems on prime farmland subsoil compaction due to surface mining in the Midwest." The study is centered on four mine sites each utilizing a different combination of equipment for soil removal and replacement. Subsoil compaction is the primary focus of this research effort. Primarily owing to physical location, it is difficult to alleviate the increased compaction directly below the topsoil in reclaimed soils. Different equipment combinations cause varied effects when soils are replaced during surface mining activities. By collecting field data within a statistical framework, the effects of different equipment combinations on subsoil compaction can be evaluated and conclusions drawn. This research effort evaluates a comparison of natural and replaced soils by moist bulk density data. This comparison centers on changes in bulk density and texture to a depth of 48 inches. For each study site a complete case study is provided for use in data correlation and interpretation. Basis for this research effort centers on four (4) major experiment designs: o Comparison of soil bulk density values for three distinct equipment systems evaluated on the same general soil types (i.e. scrapers, bucket-wheel excavators and end-dump haulback); o Evaluation of the effects of soil replacement in repeated lifts using scrapers; o Presentation of bulk density values representing soil compaction for four (4) equipment systems (i.e. bucket-wheel excavators, draglines, scrapers and end-dump haul back) on four separate mine sites in the midwest; o A prediction analysis model is developed for subsoil bulk density following reclamation based on equipment characteristics and a statistical evaluation of texture. The soil data base of information includes data from the 1982 Bureau of Mines study entitled, "Impact of Surface Mining on Soil Compaction in the Midwest" as well as data from this research project. The final report is synthesized through an analysis of field data, statistical analysis and literature review. The final report focuses on the interpretation of results for practical application by government and industry.

Jan 1, 1984

The evident need to improve the reliability of fluid power systems in underground coal mining equipment prompted the U.S. Bureau of Mines, and later the Department of Energy, to contract with the Fluid Power Research Center at Oklahoma State University for a research project to develop methods for achieving this end. Since the work of the contract was completed at about the time DOE was relinquishing its underground coal mining projects to BOM it was decided to issue the final report under 80M cover. The contract revealed that the major causes of poor reliability were: (1) poor overall system design, (2) poor component contamination toleranace, (3) poor system filtration, and 4) poor maintenance practices stemming from a lack of defined maintenance procedures and enforcement of same. This report demonstrates the variability of the reliabilities of components of similar performance description when subjected to standard tests. Improved design procedures are recommended and the information needed to specify and select components whose reliability is predictable and optimum without sacrifice in performance or significant increase in envelope size.

Jan 1, 1983