Search Documents

By J. J. Bean

This paper, describing the milling practice at the oxide concentrator of the International Smelting Co., is one of a series on milling methods and costs being published by the United States Bureau of Mines. GENERAL DESCRIPTION The oxide concentrator is properly an integral part of the Tooele plant of the. International melting Co., located 5 miles from Tooele, Tooele County, Utah. It has a capacity of 300 tons of ore per day and uses an all-flotation process to treat custom siliceous oxidized lead ores obtained principally from the Tintic district in Utah. Ores found amenable to the process are purchased on a custom basis, the principal tonnages being obtained from the Tintic Standard and North Lily mines.

Jan 1, 1933

A parametric study was conducted to establish the optimum operating conditions for the column flotation of fine coal. The parameters examined in this investigation included collector and frother dosages, feed solids content, and the volumetric flow rates of feed slurry, air and wash water. Despite the wide range of conditions studied the experimental data were found to fall along single grade-recovery curves, just below the maximum separation predicted by the release analysis technique. The deviation of the parametric test data from the release curve was attributed to the nonselective entrainment of mineral matter associated with poor froth washing. The operating point on the characteristic recovery-grade curve was found to be primarily determined by feed rate and aeration rate.

Jan 1, 1992

By R. H. King

Recently, the North American mining industry experienced a severe recession, forcing managers to take dramatic steps to cut costs and compete in the difficult international market. Some of these steps were closing mines, reducing work forces, renegotiating wage agreements, and purchasing the most productive equipment. Managers are now looking beyond these traditional avenues and are focusing more on advanced technology. In the present environment, it is essential that mine operators obtain the maximum use of capital expended on equipment. However, mine workers do not obtain maximum efficiency or productivity from equipment because the adverse and hazardous mine environment impedes human performance. Also, the efficient use of large, complex machines calls for levels of precision that many times are beyond the capability of even highly trained miners. A possible solution to this problem is a machine that mines without operators - autonomous mining machines. However, numerous problems confront researchers who are attempting to develop such equipment. Some mining tasks are not always composed of a series of cyclic motions readily performed by factory floor robots. In addition, mining takes place in the geological environment where conditions are highly variable and unpredictable. As a result, these machines must be able to sense and adapt to variations in operating tasks and environment. Considerable autonomous vehicle research has been completed, especially for defense. However, autonomous vehicle (AV) technology has not advanced to practical application yet (King, 1988) and mining research is necessary in areas: representing mining specific knowledge; •analyzing and reasoning about sensor data in the mining environment; and •discovering completely new mining methods or new approaches to existing methods that become apparent when we remove the constraints imposed by the necessity of human operators. A specific machine, the LHD, can be used to show the problems for researchers who are attempting to develop autonomous machines for mining. This author chose the LHD because it can borrow concepts developed for autonomous navigation by military programs. But considerable mining research is also required. Furthermore, studies done at the Henderson mine, in Colorado, show autonomous LHD 's promise cost and safety benefits (King, 1988). At Henderson, LHDs load ore from draw points, tram to an ore pass, dump and return, or switch to another draw point. An autonomous LHD must sense vehicle position along the route, relate sensor data to stored-map information, to determine location, follow drift center lines, plan paths between dump position and initiate appropriate control commands, sense vehicle operating status and vehicle health, key on features or targets for special tasks like high speed turns, perform end of travel tasks (loading and dumping), and detect and avoid obstacles. These goals are similar to those for shuttle cars, trucks, and front-end loaders. Therefore, much of the technology is transferable. Each Henderson LHD extracts six to 40 dippers from each of a series of draw points. The LHD transports the ore to an ore pass within 55 m (180 ft) of the draw point, making the longest round trip 110 m (360 ft). The LHDs have very fast hydraulic dumping and loading systems that reduce the round trip cycle to less than one minute. Even though the LHD is capable of 500 trips per shift, the average production is 300 dippers. Man trip and lunch reduce available operating time to 6.5 hours per shift. Mucking difficulties (setting large boulders aside), operator breaks for activities like talking shop, and cleaning and smoothing roads further reduce operating time. Supervised autonomy can reduce the number of operating units by increasing operating time per shift since computer controlled machines can operate during lunch and between shifts and reduce operator errors. If dippers per shift increase from 300 to 350 (long-range goals are 500 dippers per shift), constant production requires only 10 operating LHDs and two spares. Manpower requirements drop from 24 to four by controlling five machines from one workstation. A review of technology available from the Autonomous Land Vehicle, the Advanced Ground Vehicle Technology, the Ground Surveillance Robot, and other programs, show the following differences between others work and mining industry needs: •If we focus initially on mobile haulage vehicles, we can navigate from a map. We do not need to explore. •We can modify the environment to reduce the navigation requirements. •We have a harsher environment than any of the research programs have encountered. •Our equipment must operate faster and more precisely than present AVs. •Our equipment must operate reliably over long periods of time. •We must have better onboard machine health monitoring and diagnostics. •The AV programs do not address geosensing. •The major AV programs are not cost-effective. For example, we cannot afford the computer power for robust image processing, yet. To computer control an LHD, we must replace the guidance and monitoring skills of experienced operators with sensors, computing hardware, interfaces, and several software mod¬ules. Experienced operators avoid collisions and load efficiently in piles that may contain oversize muck. Collision avoidance without an operator requires sensing all obstacles in the draw

Jan 1, 1991

By Ronald Althouse

During the past five years under contract with the U. S. Bureau of Mines (BOM Contract J0308002). West Virginia University's Mining Extension Service (WVU-MES) has designed, developed) and delivered to the mining industry a comprehensive training program for Mine Rescue (MR) teams and a management planning tool for Mine Emergency Preparedness. The Mine Rescue team program is systematically built on a set of training objectives, backed up by content, allowing mine operators to conduct team training activities. These materials are user-ready, provide the MR principles and practices for both initial and advanced training, and supply teams with exercises geared to problem-solving activities. In addition to an instructor's program guide, the eight (8) modules that comprise the initial (20 hour) MR training are: an Introduction to Mine Rescue, an Introduction to Self-Contained Breathing Apparatus (SCBA), a set of modules covering each approved minimum 2-hour SCBA (i.e.) the Draeger BO 174-A. the McCaa) the Aerolox. & the Scott Rescue-Pak), and a manual on Auxiliary Apparatus as well as the Chemox Auxiliary SCBA. Advanced, annual refresher training (40 hour) is covered by seven (7) modules that spell-out the principles and practices needed to establish surface organization, to handle mine gases as well as mine ventilation, to conduct exploration, for fires, firefighting, and explosions, to rescue survivors and recover bodies, and to accomplish a mine recovery. Approved by MSHA in 1984 to meet requirements for 30 CFO. Part 49, these materials provide a basis for trainers' instruction, for comparison of team capabilities, for modifying programs resources, and services, and for program planning. The Mine Emergency Preparedness Program (MEPP) is used by management as a tool in the preparation of company personnel for handling a mine emergency operation. As a wholly new program. MEPP depends upon development of a Mine Emergency Organization and Emergency Operations Procedures. It also requires regular scheduling of drills) periodic mock emergencies, and evaluation of organizational responses and program performance beyond required training of mine rescue teams. MEPP materials are arranged into three sets of guides: 1) the Preparedness Program System Guides include an Executive Summary, a Program Director's Guide Mine Emergency Organization, and Emergency Operations Procedures; 2) the Emergency Organization (MEO) User's Guides cover the Rescue and Advisory Division, the Technical/Safeguarding Division, and the Surface Support Division; and 3) the Emergency Procedures (EOPS) User's Guides detail Containment Level Procedures, Notification Level Procedures. Mobilization Level Procedures, and Deployment Level Procedures.

Jan 1, 1986

By Henning R. Norbom

Lime has been produced for many centuries. The simple pot kiln was one of the first devices used in this process. It was constructed of stone often on the side of a hill to reduce construction efforts and provide easy access to the top for feeding of limestone. It was fired from below with wood and coal. The pot kiln was very small and operated on the batch principle. The kiln being cooled between each batch, the fuel consumption was horrendous. The lime quality was poor with perhaps only one half of a batch being lime of suitable quality. Of the remaining half one part would be over burned and another part underburned. For centuries the lime burning technique was improved at a barely recognizable rate. One of the first major steps forward was the introduction of the continuous process vertical lime kiln. Although at first crudely constructed, the kiln had a refractory lining. It was charged with alternate layers of limestone and solid fuel usually in the form of coke. Continuous mode of operation, larger unit size and better heat distribution resulted in greatly improved fuel economy. However, quality of lime produced still left much to be desired. One problem was contamination by ashes from solid fuel.

Jan 1, 1978

By James J. Scott

Longwall mining has not received a great deal of attention in the United States; however, this system offers many advantages over the conventional room-and-pillar methods now being used. In order to conserve the coal resources of this country, the U. S. Bureau of Mines has investi¬gated the feasibility of adapting European longwall mining methods to American coal seams. Their studies showed longwall mining to be well suited to thinner seams and, greater depths; and, in addition, permitted almost 100 percent recovery of the coal. Most, experiments with this method resulted in higher overall production-costs than were commonly obtained with highly mechanized room-and-pillar techniques This high cost-was largely due to the excessive amount of labor required to maintain adequate roof support with conventional longwall mining techniques. With the substitution of hydraulic-powered, self-advancing roof support systems for conventional supports, this excessive labor cost has been decreased, and longwall mining costs are now competitive with those of modern room-and-pillar mining.

Jan 1, 1964

By K. K. Kershner

Nickel having a purity of more than 99.99 percent with reference to metallic impurities was electrodeposited at the Rolla Metallurgy Research Center of the Federal Bureau of Mines. The production of high-purity nickel is in keeping with the current trend in technologies for producing metals with lower and lower percentages of impurities. To understand more fully the role to be played by nickel by itself and as a component in many alloys, the element must be in a state of high purity. Procedures are outlined for purifying nickel solutions by precipitating and filtering off impurities. Details are given for using the purified solutions as electrolytes in depositing high-purity nickel. The elecneleposited nickel contained 0.0005 to 0.002 percent each of cobalt, copper, aid iron together with spectrographically detectable traces of aluminum, magnesium, and silicon. The deposits were smooth and dense; the crystalline structure was typical of an electrodeposited metal. Some preliminary experiments for purifying nickel solutions by liquid-liquid extraction are also described in this report. Tests of this type were limited since more encouraging results were obtained by other methods of purification.

Jan 1, 1961

By Mark Viduetsky, Dmitry Tropnikov, Victor Maltsev, Victor Sokolov, Alexander Purgin, Andrey Panshin, Alexander Bondarev, Pavel Kozlov, Igor Garifulin

"CFM pneumatic flotation machines were developed by the Institute of Materials Science and Metallurgy, UrFU, and designed to concentrate a wide range of ores and man-made materials. A key principle of work is pulp preparation for flotation owing to its saturation with finely dispersed air bubbles in ejectors. CFM plants, their advantages over domestic and foreign prototypes are described. CFM pneumatic machine commercialization resulted in: - machines demonstrated high floatation efficiency for concentration of rebellious pyrrhotite-bearing copper and zink by simultaneous floatation of copper and zinc minerals and depressing pyrrhotite. CFM- 1400M introduction allowed simplifying and optimizing the flow chart and increase extraction of copper - by 5.4%, zinc - by 9.5% and improve the quality of copper (3% Cu) and zinc (1.5% Zn) concentrates. - due to copper pyrite concentration by using CFM 1400M overall copper recovery was increased by 1.5 %, and the content of copper in concentrates - by1%. According to the results of pilot runs, the use of CFM flotation for zinc cakes concentration strongly intensifies the process of cleaning water-soluble metal compounds and, thereby, increases the efficiency of flotation concentration and subsequent milling. CFM machines showed higher specific capacity (three or four times higher) (both for feed material and froth product). Specifically, CFM froth product has higher content of useful elements (silver by 0.014 % abs. zinc by 0.31% abs.) and better extraction (silver by 6.08% abs., zinc by 0.31% abs., and sulfide sulfur by 13.7 %). Sulfide sulfur content of CFM product chamber as compared to mechanical flotation machines is two times lower (0.48 vs. 0.95 %)."

Jan 1, 2014

By P. H. Rodriguez

The aquatic hazard classification system of the OECD and EU requires that sparingly soluble metal substances (SSMS) be tested using the OECD Dissolution/Transformation protocol in order to quantify the release of the ecotoxicological relevant species (dissolved ions). The SSMS category contains massive forms of metals, which due to their low solubility and slow transformation characteristics are a special case. The main factors that produce the release of metal into solution are exposed surface loading, pH, and stirring rate. The classification system at present prefers the use of mass loading as opposed to surface loading, in which case the amount of metal released will primarily be a function of the pH, and mass loading. Within the framework of the European Copper Voluntary Risk Assessment, coordinated by the European Copper Institute, we have proposed and developed a methodological procedure in which we demonstrate that surface area is an intrinsic property of a SSMS and we link the exposed surface loading to the toxicity reference value in order to obtain an aquatic hazard classification for massive metals. As example, the aquatic hazard classification for copper massive will be discussed. This approach is recommended for metal massives and metal powders.

Jan 1, 2007

By R. G. Warncke

In the 1953 National First-Aid and Mine Rescue Contest, 58 teams from 9 States participated, 14 teams from 6 States in mine rescue and 47 teams from 9 States in first aid. Three of the teams were combination teams in that the same team participated in both the mine rescue and first-aid contests. The States represented and the number of teams from each State are shown in table 1. [ ] The contest was conducted in accordance with the general rules prepared by the Rules Committee and approved by the General Committee of the National First-Aid and Mine Rescue Committee.

Jan 1, 1955

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor, and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research that was conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

May 13, 2021

By D. S. Hines

The purchase of mechanical equipment for mines is not unlike the purchase of other materials or supplies in general principle, but on account of the major part such equipment plays in the operations, and of the fact that life and valuable property are at stake, the matter demands the most careful attention on the part of the purchaser. The problems and difficulties encountered are dealt with below in their sequence in the purchasing procedure. Requisiting Although it is quite a common practice to submit a tentative specification of requirements to recognized manufacturers of equipment- soliciting alternative propositions or recommendations for study in the selection of certain equipment-as a rule the first step in purchasing procedure is the requisition. Primarily, it is the form that carries to the purchasing department the record of equipment wanted. A full and complete description or specification, and accuracy of record, are the important points to be insisted on in a requisition. Too much attention cannot be given to this detail, as this is one of 'the most important phases of purchasing work. Incomplete information, either in specification or detail, leads to delay in handling the requisition, and, if not detected in the purchasing department, may mean receipt of material which cannot be used for the purpose intended. In addition to description of material or equipment to be ordered, the requisition should also show where or what the equipment is for, whether for operating or new work. If for capital account, the number of the authority for expenditure should be given for record and distribution purposes.

Jan 1, 1930

By Graham J. Morgan

The following material is excerpted from a presentation Mr. Morgan gave recently to representatives of the financial community. Introduction 1982 was a period of challenge for United States Gypsum Company because of reduced market opportunity. Housing starts for the first 10 months averaged a seasonally adjusted annual rate of 1 million units, 9% below the comparable 1981 period when housing starts were the lowest in 35 years. Industry gypsum board shipments declined 9% from the already low levels of the same period in 1981. US Gypsum met the challenge with stringent cost reduction programs and aggressive action in the marketplace. In late 1981, anticipating market deterioration, the company's management adopted strategies to focus on two shortterm objectives: • Adjust operations to perform profitably in view of limited opportunities through more efficient operations and asset management. • Continue to strengthen U.S.G.'s resources and ability to take advantage of important market opportunities as the economy improves through selective expansion of production capacity in key growth markets. Concentration on these two objectives resulted in a nine month performance in 1982 that, while certainly not satisfactory by company standards, compared very favorably with that of principal competitors in terms of net earnings, margin on sales, and return on average stockholders' equity. To counteract limited market opportunities, U.S.G. focused on productivity improvement, cost reduction, expense control, and maximization of market penetration. Energy Use Improving performance encompassed all segments of operations. For example, efficient use of energy was a significant factor despite lower operating rates at most plants. Overall, in the third quarter of 1982 versus 1972, the company used 27% less energy per unit of production, a savings of $15 million in that quarter alone. These continuing improvements helped to partially offset constantly rising energy costs. A number of operations achieved superior results in the first nine months of the year compared with the same period in 1981. For example, gypsum board plants in Jacksonville, FL, and Sweetwater, TX, recorded 8% and 7% reductions, respectively, in energy use per unit of production. Paper mills in Oakfield, NY, Galena Park, TX, and Kansas City, MO, each reduced energy use more than 12%, while the Greenville, MS, ceiling products facility achieved a 16%o reduction. Safety Safety is another important element that received increased attention. U.S.G.'s safety performance over the past five years has consistently improved. In 1981 it was five times better than that of the gypsum industry; nearly 10 times better than all industry as measured by the National Safety Council; and almost 20 times better than all US manufacturing as recorded by the Bureau of Labor Statistics. In addition to human concerns, this excellent record results in significant dollar savings that directly affect company results. In 1981, U.S.G.'s pre-tax savings in claims, premiums, and related expenses were about $20 million compared to the industries in which it competes. For the first half of 1982 performance improved further, with a cumulative lost workday incidence rate per 200,000 man-hours worked of only 0.27, an all-time record. Expense Control Careful control of inventories and receivables also received special attention. As of Sept. 30, 1982, inventories were 29%, or $44 million, below the level of Sept. 30,

Jan 2, 1983

By G. H. Blackwell

Open pit mine management must ensure that sufficient trucks are available and are being used effectively for production, and that operating costs are under continued control and review for improvements. This paper describes methods for estimating truck fleet requirements which have been used effectively at large- and medium-sized open pit mining operations. Applied to commonly available data, multiple regression analyses can indicate when mine plans should be revised toward optimizing the number of trucks required. Prediction of major cost items for budgetary purposes is addressed, along with an example of how readily available production data can be used to reduce costs systematically.

Jan 1, 1999

By William H. Lane

After a number of years of engineering and operating assignments and through many types of evaluations, the need for a simple analytical method of evaluating mine haulage alternatives became obvious. Haulage, like 50 many other facets of mining, is generally a sequence of interconnected events that change, often drastically from mine to mine. Often the operator or the mine engineer has neither the time, manpower, facilities, or information needed to prepare a detailed evaluation. For many studies or for routine variance analysis, that detail may not be necessary. The intent of this article is to present an approach for analyzing mobile mine haulage that is simple and straight-forward. These methods are not designed to replace more formal and detailed procedures that have been developed previously and are available in our technical libraries. They are offered as a tool to be applied to preliminary designs, feasibility studies, and variance analyses where more complete detail is not warranted. These methods will eliminate combinations that are not economical or appropriate before more intensive and complete evaluations are undertaken. These methods may also be used to evaluate ongoing operations and to plan changes in those operations. This presentation describes a series of steps that have evolved for the handling of haulage evaluations. It concentrates on the factors having major impact on the results. Because the approach is a sequence of distinct steps, a case study was chosen as the best method of presentation. This case is a composite of several actual situations that have been encountered within the last few years.

Jan 1, 1978

By John A. Richards

This paper is one of a series being published by the Bureau of Mines on mining methods and costs. It describes briefly the manner in which slusher hoists and scrapers are used in connection with clock-caving methods at the Emma Nevada mine of the Consolidated Coppermines Corporation, Kimberly, Nev. Kimberly is in the Robinson mining district, White Pine County, 7 miles west of Ely. The district is served by the Nevada Northern -Railroad, which branches from the main line of the Southern Pacific at Wells, Nev., 140 miles north, Paved U. S. Highway 50 from Salt Lake City, Utah, to Reno, Nev., passes through Ely. The altitude at the collar of the Emma Nevada shaft is 7117 feet. The surrounding hills are covered with a sparse growth of juniper, pinon, and mountain mahogany.

Jan 1, 1940

By R. J. Gunderman

Cable reel systems for shuttle cars were investigated to determine whether an improved system could be identified. Interviews and mine visits were conducted to better define limitations and problems with present systems. Although simple and relatively inexpensive, present cable reel systems are not fully satisfactory. Several concepts for a different technical configuration were formulated and evaluated. An all ectric system using electronic control and external sensors was recommended for further development.

Jan 1, 1980

By B. Hines

Grinding efficiency in a vertical stirred mill is affected by a wide range of process and mill configuration variables. Of these, the media fill, size, and intrinsic density have a significant effect on power draw and grinding performance. Media-related factors that influence grinding performance include, e.g.,a higher media filling providing additional particle breakage sites, or a lower bead density decreasing the running torque at a given media filling. It has been estimated that the grinding media can cause up to a 30% change in the specific energy required to grind. FLSmidth has generally recommended that the intrinsic density (specific gravity) of the grinding media be more than triple the slurry density. This density difference helps to ensure that sufficient stress intensity is generated in the mill to provide particle breakage. It also reduces the chance of media ?float? if there is a spike in either slurry density or slurry flow rate. The VXPmills have historically operated at slurry density values between 1.2 and 1.5 kg/L, which translates to nominal bead intrinsic density range between 3.6 and 4.5 kg/L. The current trend towards regrinding bulk flotation concentrates to even finer sizes, to improve recoveries of fine grained minerals, has provided motivation to consider closed-circuit operation of stirred media mills. The slurry density in this application is typically higher than in open-circuit operation due to the higher percent solids in cyclone underflows. An additional effect is that closed-circuit operation increases the potential for media float due to higher flow rates as slurry is recycled to the mill. The normal progression in extending the operating range of existing equipment is to carry out laboratory testing before pilot-scale and plant-scale trials. The results presented in this paper examine the media density to slurry density ratio and its effect on grinding performance.

Feb 23, 2014

By E J. Y Koh, G J. McLachlan, E Amini, N Beaton

Preconcentration greatly reduces the ore mass input to the processing plant while upgrading the grade. One of the commonly used methods of preconcentration is optical sorting. These methods rely on optical sensors which classify the material stream into “accept-reject” streams. Currently, it is common to use near infrared (NIR) or colour cameras to classify streams based on reflectance or colour thresholds set by experts. The imaging is done through line-scan sensors where the material is scanned on a belt or a chute. Then, a separation apparatus like a diverter gate or air jet is controlled to separate the streams according to the classification made by the algorithm. Separation efficiency is dependent on the classification algorithm. Existing classification algorithms rely on low-level feature discrimination like observing individual pixel values for reflectance or colour hues. This limits discrimination between minerals with low contrast in colour. Human experts perform mineral segmentation using texture, colour distribution and shape, but it is difficult to translate these visual rules to mathematical thresholds. Deep learning methods like Convolutional Neural Networks (CNNs) provide high-level feature discrimination similar to a human expert. Instead of relying on pre-defined features, the CNNs learn complex features from the dataset. CNNs can construct a hierarchy of features based on pixel clusters to learn texture, shapes, and colour spectrums of the mineral grain surface to provide better separation. In this study, a state-of-the-art deep learning instance segmentation method is used to outline boundaries and classify grains from the background (mineral segmentation). The algorithm is trained on images collected from a flotation feed of a gold deposit, where the gold is mechanically locked inside pyrite. This method can process on-line video inputs at 5 frames per second to provide a live grade. The proposed method is inexpensive as it only uses a camera and a desktop computer.

Nov 10, 2020

By Robert E. Wood

The compressibility factors, Z, of helium, nitrogen, and helium-nitrogen mixtures in the three-dimensional space of temperature, pressure, and gas composition have been related to the Leiden form of the virial equation of state. The dependency of virial coefficients through the fifth on temperature and gas composition has been established for the temperature range 133.15° to 748.15° K. Compressibility factors, Z, have been computed from the equation of state and tabulated as functions of gas composition, pressure, and temperature. Tabular values of Z are presented for 30.00 through 100.00 percent helium for temperatures from 240° through 700° R for pressures from 14.696 through 3,050 psia and for temperatures from 720° through 1,300° R for pressures from 14.696 through 1,500 psia. Tabular values of Z are presented at increments of 5.00 percent helium and 20° R, and, for pressures greater than 50 psia, at increments of 50 psi.

Jan 1, 1967