Search Documents

This report summarizes the work performed and results achieved on the above contract from October 18, 1971 through July 14, 1972 under Phase II, Task 1: Detailed Design of Prototype and Task 3: Supporting Experimental Investigation. Operation and Service Manuals resulting from Task 3 are submitted under separate cover as are detailed design drawings and specifications, prepared under Task 1. Both items accompany this report. This report also includes (A) an estimate of the cost of construction, (B) a description covering the use of the equipment, and (C) a proposed test plan to demonstrate performance of the equipment in both the laboratory and a mine.

Jan 1, 1972

By M Zlatev, S Silge

Producers of primary resources such as iron ore face the challenge of processing crude materials with increasing levels of impurities, which may result in the requirement for wet processing. This results in a significant increase in water usage, power consumption and operating costs. Given the remote locations of most operations in Australia (Stewart et al, 2013; Prosser, Wolf and Littleboy, 2011), the required volumes of power and fresh water for wet processing can be very difficult to achieve.HAVER&TYLER is renowned across the world for their screening technology in wet and dry processes. Its innovative Hydro-Clean® system represents a cost-effective and eco-sensitive way to clean any crude materials and material blends with a grain size distribution of 0–150 mm that are contaminated with adhesive clay, slit and other impurities.CITATION:Silge, S and Zlatev, M, 2015. Iron ore washing – achieve more with fewer resources, in Proceedings Iron Ore 2015, pp 519–528 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J Harris, P Kirsch, D Cliff, M Spinks, S Goater, D Sprott

Fires are a common and recurrent unwanted event in the operation of open pit mines. In most cases, the causes of events such as fires are already æknownÆ but are either overlooked or not fully addressed in planning. Ongoing rapid growth of the global mining industry is creating a scarcity of skilled personnel, and high turnover within operations. This contributes to loss of corporate memory in risk management activities. RISKGATE« is an online risk management system designed to support and assist in the analysis of priority unwanted events in Australian coal mining operations. Funded by the Australian Coal Association Research Program (ACARP), RISKGATE« is a knowledge management program that delivers best-practice controls for unwanted events and assists operations in staying abreast of emergent risks and threats. RISKGATE« content has been primarily developed from an association of industry experts, and enriched with input from additional academic and technological resources. In mining operations, RISKGATE« provides a continuum of knowledge and best practice for risk identification, assessment and management. RISKGATE« will assist companies in improving safety performance, operational efficiency, operating practice and training. Here we present the RISKGATE« prototype as developed in 2011 for Fires, with a case study presented for the initiating event Fires on Mobile Plant.CITATION:Harris, J, Sprott, D, Spinks, M, Cliff, D, Goater, S and Kirsch, P, 2012. RISKGATE« - A case study in application to fires on mobile plant, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 49-54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By W. R. Ingalls

DUPING the last two years, and especially during the last six months, a number of important articles upon the new methods for the desulphurization of galena have been published in the technical periodicals, particularly in the Engineering and Mining Journal and in Metallurgie. I proposed for these methods the type-name of "lime-roasting" of galena as a convenient metallurgical classification,' and this term has found some acceptance. The articles referred to have shown the great practical importance of these new processes, and the general recognition of their metallurgical and commercial value which has already been accorded to them. It is my present purpose to review broadly the changes developed by them in the metallurgy of lead, in which connection it is necessary to refer briefly to the previous state of the art. The elimination of the sulphur-content of galena has been always the most troublesome part of the smelting-process, being both costly in the operation and wasteful of silver and lead. Previous to the introduction of the Huntington-Heberlein process at Pertusola, Italy, it was effected by a variety of methods. In the treatment of non-argentiferous galena concentrate, the smelting was done by the roast-reduction method (roasting in reverberatory furnace and smelting in blast-furnace); the roast-reaction method, applied in reverberatory furnaces; and the roast-reaction method, applied in Scotch hearths 2 Precipitation-smelting, simple, had practically gone out of use, although its reactions enter into the modern blast-furnace practice, as do also those of the roast-reaction method.

Sep 1, 1906

By D. J. Buchanan

British Coal's mining research programme is directed towards the strategic objectives of reducing production costs, improving product quality and resolving health, safety and environmental issues. The strategy for R&D is described and selected parts of the programme are reviewed. Two major initiatives are directed towards reducing production costs: geotechnics and automation. Integrated exploration techniques are used to delineate geological structures as an aid to mine planning. Rockbolting is being rapidly introduced and the in situ stress field has been found to be of significant influence. Automation is the subject of a major programme. A strategy for coal quality has been devised. The health, safety and environmental programme concentrates on the traditional hazards together with surface environmental problems.

Jan 12, 1992

By Andrew Case

The Port Nickel facility in Braithwaite, Louisiana, is known for pioneering hydrometallurgical processes for the 'separation and recovery of nickel, cobalt and copper. Ten years ago, in 1985, a new CRI-MET process for the recovery of molybdenum, vanadium, nickel, cobalt and alumina from spent catalysts was developed and implemented. Spent- catalysts from the petroleum industry consietute the majority of feed. These are not only a valuable-source of metals, but due to EPA regulations are frequently classified as hazardous under RCRA. Molybdenum and vanadium are selectively leached in an oxidative hydrothermal step. Alumina is then extracted in a caustic digestive leach. The unique technology produces four primary commercial products l molybdenum trioxide, vanadium oxide, aluminum trihydrate and nickel-cobalt concentrate. This paper discusses the process, modifications. during ten years of operation, and the relationship of these modifications to the future of the catalyst recycling business.

Jan 1, 1995

By J Mar·n, R Anderson, S Strohma, R Harvey

Xstrata is the operator of both Minera Alumbrera Ltd (50 per cent Xstrata, 50 per cent Wheaton River) and Ernest Henry Mining Pty Ltd, (99.99 per cent Xstrata), both copper-gold deposits, using conventional SAG/ball milling at current capacities of 36 Mt/yr and 10.3 Mt/yr respectively. Alumbrera is located in Catamarca Province, in the north west of Argentina. Ernest Henry is located in Cloncurry, north west Queensland, Australia. Both operations started in late 1997, with commercial production achieved in early 1998. Different designs and equipment are in use for both operations, however the evolution of SAG milling performance, although logically related to their specific features, reflect similar trends of consistent increases in throughput. This paper will discuss the main changes to the SAG mill liners in both operations and the results achieved to date. A summary of the operating strategies will be included.

Jan 1, 2003

By E. Morrice

High-purity neodymium, praseodymium, and didymium (a cerium-free mixture of light rare-earth elements) were prepared by electrolysis of the oxides in a medium consisting of the respective rare-earth fluorides and lithium fluoride. The metals were electrodeposited in the liquid state and collected as nodules on a skull of frozen electrolyte. Cells were operated from 1,000° to 1,100° C. The requisite temperature was maintained by passing alternating and direct currents through the bath. Graphite was used for the anodes and tungsten for the cathode. The metal products contained <0.02 percent each carbon and oxygen and <0.025 percent tungsten as major impurities. Analysis of typical didymium metal nodules showed an approximately twofold enrichment in neodymium and praseodymium over their respective concentrations in the cell feed. The lanthanum content of the metal was about one-half its content in the oxide.

Jan 1, 1967

By W. G. McBride

INTRODUCTION Preparation of this article, at the request of the Committee on papers, has been undertaken in the hope that it may stir up helpful discussion and constructive criticism. The Canadian mining industry is in the dumps and there is no use trying to deny the fact; nor does it help to say that other industries are in as bad or a worse condition. Let us face the situation honestly and see just how serious it is. The entire financial and industrial world is in a state of depression. The gravity of the case is no doubt exaggerated by contrast with the wave of optimism and false prosperity which pre-ceded it. The prevailing gloom and pessimism are just as irrational as was the former super-optimism. As far as we mining engineers are concerned, the causes are quite beyond our control, and it is the effect upon our own industry which interests us most. This effect is an accumulation of mineral products with consequent depression in price to a point where profits have almost, if not quite, disappeared. Whether this accumulation of stocks is the result of over-production or under-consumption is difficult to say, but it would seem likely that there is a combination of the two. The introduction of selective flotation has brought about a large increase in the production of zinc, a moderate increase in the production of lead, and a comparatively small increase in copper. It has turned relatively small mines into great producers, as in the case of the Sullivan, revived expiring mines like La Cananea, and brought-in new ones like Flin Flon

Jan 1, 1931

By David Crouthamel, Raymond Henn

"The need to fill the void space or annulus created between an excavated tunnel or shaft and the final lining system has long been a requirement in underground construction. Most of those types of voids are created as a result of employing the two pass tunneling lining method. Filling of this void is called backfilling. For many years the materials used as backfill were primarily reinforced and non-reinforced concrete, sanded grout, neat cement grout, or blown-in sand/pea gravel. However, in the past 20 years the use of cellular grouts/cellular concrete as the backfill material has greatly increased. Most cellular grout is made of a mixture of water, Portland cement (with or without the addition of fly ash), a foaming agent and admixtures such as a water-reducer or superplasticizer.It is the authors’ preference to use the term cellular grout as opposed to cellular concrete since by ACI Concrete Terminology an ACI Standard (ACI CT 13), concrete contains aggregates. Normally cellular grout does not contain sand (finite aggregate), but almost never contain course aggregates.The authors believe there are several reasons for this increased use of cellular grout as backfill, such as:• The increase utilization of the various trenchless tunneling methods. Tunnels constructed using trenchless method tend to be smaller in size, excavated diameter or cross sectional area. Making man-entry for placing backfill from inside the secondary liner, utilizing pre-installed grout posts, more difficult if not impossible. It is these workspace restrictions that are the drivers as to when to utilize grout ports installed during the pipe/liner fabrication versus grout delivery pipes installed within the void/annulus space.• The ability of cellular backfills to be pumped and flow longer distances.• The unit weight of cellular grouts can be controlled by mix design and generally can range from 560 Kg/m3 (35 lbs/CF) to 1040 Kg/m3 (65 lbs/CF)."

Jan 12, 2017

By Iván Ibañez

An essential aspect of energy efficiency is determining the opportunities to improve a system or machine's performance from the energetic point of view. For the mining industry, it's a classic problem that mainly all the equipment manufacturers face today to produce the same results with the minimum energy requirements. Existing research focuses on light-duty vehicle energy losses. However, heavy-duty off-road machinery is understudied. This article presents an energy balance assessment of a mining vehicle utilized in an open-pit mine in Colombia.

Sep 29, 2023

By Don K. Smith

The northern zone of the Indus Basin comprises a vast area of essentially level land in West Pakistan which is irrigated by means of a complex system of canals that distribute more water to more land than any other irrigation system in the world. In spite of the development of this extensive irrigation system, production of food and fiber has not met the requirements of the country. The major reasons that crop production has not reached anticipated levels are the lack of adequate irrigation supplies and effective subsurface drainage. As a result, yields per acre are among the lowest in the world for areas where irrigation is practiced, and many thousands of acres of valuable crop land have been removed from production or are seriously affected by salinity and waterlogging. To rectify the problems of irrigation supply and drainage the Government of Pakistan has undertaken a program of Salinity Control and Reclamation which is being administered by the Water and Power Development Authority. The Authority retained Tipton and Kalmbach, Inc. , of Denver,, Colorado as Engineers for the program in the northern zone of the Indus Basin. -This program consists of the construction of about 30, 000 irrigation wells to provide drainage for waterlogged lands and full irrigation supplies, including leaching requirements, for; all cultivated lands. The program will ultimately ensure the productivity of 20 million acres and will involve an annual pumpage from ground water storage of nearly 40 million acre-feet of water. The value of the crops produced when the program is in full operation will be 4 to 6 times the value of the crops that could be produced without the benefits of this program.

Jan 1, 1967

By G. M. Evans, S. Mitra, G. J. Jameson, M. M. Hoque, E. Doroodchi, R. Moreno-Atanasio

In this study, the detachment behaviour of 314 μm diameter silica particles from a single 3 mm diameter bubble rotating in a confined cavity connected to a cross-flowing water channel was investigated. The liquid cross-flow generated a rotating flow inside the confined cavity, which was quantified using 2D particle image velocimetry (PIV) measurements. The fluctuating (x-y) velocity components inside the cavity for each cross-flow velocity, U, were then used to estimate the corresponding time/volume average turbulence intensity values, Ti. Turbulence intensity ranged from 9.3-16.2%. In the absence of a bubble, the rotating vortex within the cavity created a pressure field which decreased towards the centre of the vortex; wherein the lowest pressure zone was located at the centre of the cavity. The vorticity into the cavity was found to increase with increasing the turbulence intensity. A bubble, both without and with particles attached, was introduced into the cavity under different flow conditions and its motion was tracked using the shadowgraphy technique. Experimentally, it was found that the bubble-particle aggregate was trapped at the centre of the cavity (low-pressure region) following a spiral trajectory. An interface resolved 3D computational fluid dynamics (CFD) model was developed to predict the particle detachment conditions within the confined cavity. CFDpredicted vorticity in the absence of a bubble agreed well with experimental observation. The CFD analysis indicated that the vorticity inside the cavity was not significantly changed when a single bubble was introduced. On this basis, the computed vorticity was utilised in describing the force balance applied to the attached particle. Computationally, it was found that the critical turbulence intensity, beyond which the particle was detached from the bubble, was 14%. This value was consistent with the experimental observation of detachment at Ti at 15.7%, and above, but not at lower values. Keywords: Bubble, particle, turbulence intensity, vorticity, particle detachment, CFD, PIV

Jan 1, 2020

By William W. Odell

In Europe and in certain other foreign countries studies have been made, extending over a period of years, relating to the winning of oil from oil shale. More work has been done in these countries than in the United States, for the reason that a supply of natural petroleum has not been so generally available there as here. Information has been obtained relating to present practices in these foreign lands in the development of a shale-oil industry. It is realized that in the past there has been very little inducement to invest capital in shale-oil enterprise in the United State&apos;s because the supply of petroleum has been plentiful; however, the time possibly is not far distant when the utilization of oil shale may be cons¬idered a desirable and financially sound venture, as it may be necessary before long to augment our supply of oil with that recovered by processing shale. The data presented herein portrays at least some of the thoughts of those engaged in obtaining oil from oil, shale in Europe, and they depict some of the results thus far obtained as well as certain plans for further efforts to win oil from shale; it is hoped that those who undertake the development of a shale-treating industry in this country will find useful information in this report.

Jan 1, 1946

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant, it was critical to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. Various compaction parameters were verified and established on a small laboratory-scale compaction machine to obtain a coal cake of acceptable stability. These parameters include cake density, cake surface moisture, transverse strength (force applied perpendicular to the original compacted coal cake layers), and applied force to the coal cake. This work determined the behavioural characteristics of the coal while being compacted either with a full-sized or a 1/3-sized compaction plate in a 9 kg capacity mould. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.The target wet cake density of 1 100 kg/m3 (79% of 1 400 kg/m3 relative density) was achieved for Waterberg sscc, with a particle size d50 varying between 0.6 mm and 1 mm, utilizing the 1/3-sized compaction plate in the laboratory-scale set-up, with 11.6% surface moisture and 92.2 t/m2 commercial equivalent applied force. For Oaky North hard coking coal, a wet cake density of 1 189 kg/m3 (85% of 1 400 kg/m3 relative density) was achieved at a surface moisture content of 12.3% and at a lower applied force than that for Waterberg sscc, i.e. 78.5 t/m2.Coal cakes of acceptable strength, and therefore sufficient stability for further processing, were obtained for all materials evaluated during this study.Further studies should be conducted to determine the effect of zeta potential during the compaction of coals.IntroductionExxaro Resources has successfully installed and commissioned a world-class stamp-charging horizontal 1 t electrically-heated pilot-scale coke oven at its Metallurgy Services facility. Prior to operating the coke non-recovery pilot plant, it is essential to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. The design of Exxaro’s pilot plant is such that the coal cake is pushed inside the oven by means of a pusher plate, rather than through a ‘spoon’ feed mechanism, such as is found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength during loading into the oven, owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability, various compaction parameters needed to be verified and established on a small laboratory-scale compaction machine."

Apr 1, 2019

By Tim Lundquist

Disa Technologies Inc. provides innovative, sustainable solutions for mineral processing and remediation through its patented High-Pressure Slurry Ablation (HPSA) technology. HPSA processes solid feed material in slurry form, propelled by high pressure pumps through opposing nozzles that generate impinging jets within a collision housing. This process induces particle-to-particle collisions in a high energy zone, creating intergranular fractures along grain boundaries. In our batch scale and continuous operating testing, we have found that controlling key processing variables such as nozzle velocity, slurry solids percentage, and the number of passes can allow for controlled size reduction and maximum mineral liberation. Since 2018, Disa Technologies has demonstrated the versatility of HPSA by testing it on diverse materials, including phosphate, copper, uranium, vanadium, zinc, rare earth elements, lithium, nickel, mineral sands, gold tailings, and more. The intent of this paper is to present an overview of our test results describing in detail impacts on size reduction, recovery, and grade with a focus on HPSA's adaptability across ore types. Looking forward, it explores the potential to process materials such as DR-grade iron, clay, PGMs, bauxite, and various tailings. Additionally, it examines planned advancements in HPSA technology, including optimized nozzle spacing, higher capacity models, improved tonnage-to-footprint ratios, enhanced maintenance features, and expanded nozzle configurations.

Jan 1, 2025

By H Askari-Nasab, E Torkamani, M M. Badiozamani, S P. Upadhyay, M Tabesh

"Decision-making in mining is a challenging task. Optimal decisions regarding shovel and truck allocations, aligned with the optimal short-term production schedules, are crucial in keeping the operations in line with the company’s long-term objectives. In this paper, we present two main modelling components as the means to achieve near-optimal operational plans: a mixed integer linear goal programming model to allocate trucks and shovels to mining faces over a shift-by-shift basis so that operating costs are minimised and resource utilisations are maximised through the planning horizon a discrete-event simulation model to investigate the behaviour of a truck-and-shovel haulage system in the presence of uncertainty within mining operations. The goals integrated into the mathematical model are to: maximise production minimise deviations from the target head grade minimise deviations in tonnage feed to the processing plants from the desired feed minimise operating cost.The mathematical model provides shovel assignments and the target productions as an input to the discrete event simulation model while meeting the desired goals and constraints of the mining operation. We illustrate the applications of the discrete event simulation model by presenting a large-scale oil sands case study. The main contribution of this work thus far is the development, implementation and verification of a simulation model with a link to optimal short-term mine schedule and extraction sequence of mining faces, which assists in achieving a high level of mine plan compliance across short-term planning and operational planning time horizons.CITATION:Askari-Nasab, H, Upadhyay, S P, Torkamani, E, Tabesh, M and Badiozamani, M M, 2014. Simulation optimisation of mine operational plans, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 299–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By J. R. Guard

Development of electrical power in coal mining has been an outstanding example of adaptability. It has accommodated itself to new inventions, changing mining methods, increasing demands, increasing safety requirements and many other new conditions. With the appearance of the continuous miner in the mining machinery picture, those engineers interested in the application of electricity to mining have been thinking about what new combination of electrical apparatus will best suit this newcomer. It is the purpose of this paper to discuss the relative costs of supplying d-c versus a-c power to mining equipment with particular reference to continuous miner setups. Assume that a-c power will be delivered to the mine at some high voltage suitable for transmission to the various substation locations. Typical voltage for this purpose is 4000 volts. The problem then is to change the power to some kind of power suitable for driving the motors of mining equipment. For safety and other reasons the voltage to be delivered to the motor terminals must be under 600 volts.

Jan 1, 1950

By J. E. Gebhardt, D. McBride, T. N. Croft, M. Cross

"Heap leaching is well-established as a relatively low-cost and low-energy method of extracting metals from low grade ores. However, the design methodology, attention to the engineering details during heap construction and the long time scale in metal recovery makes the process susceptible to significant variation in the success of a heap leach operation. Often the laboratory predicted recovery rates are not achieved on site due to poor understanding of the complex physics of flow and coupled solid-liquid-thermal reactions within the multi-dimensional heterogeneous ore body. Given the large scale of commercial operations, small changes in metal recovery can substantially change the operating profitability. While there are a variety of approaches to heap leach modeling, computational fluid dynamics (CFD) modeling coupled with leach kinetic models offers a methodology to describe and understand the complexities of heap leaching. The CFD model uses leach kinetics specific for the mineralogy of the ore, including gangue chemistry, and provides an energy balance to calculate and predict temperature. Coupled with the CFD model’s inherent capability for modeling complex fluid flow, the physics and the chemistry of the heap can be simulated. This provides a tool for engineering design, as well as forecasting heap production under different scenarios. The calibrated model is used to simulate a three-dimensional test heap under fluctuating meteorological data, such as precipitation events, periodic solution application, and notably temperature. These simulations provide support for a methodology to design and engineer heap leaching of low grade copper sulfide ore. INTRODUCTION Worldwide copper ore reserves are faced with decreasing head grades with copper sulfides, particularly chalcopyrite being the predominant mineralogy (Nesse, 2000). Heap leaching offers an economical way to recover copper from low grade ore. The ore is stacked and a leach solution is applied and allowed to trickle though the porous bed of ore to extract target metals. The heap can be built with run of mine material or crushed ore and is constructed in order to achieve percolation of the leach solution to all regions. Bartlett (1998) provides an authoritative overview of the solution mining process where the leach solution interacts with the solid, the lixiviant dissolves the target minerals from the solid into the solution, and the dissolved species are transported out of the heap for subsequent recovery. Petersen (2016) provides a recent review of heap leach technology and emerging and potential future applications, and Ghorbani et al. (2016) summarizes the current state and challenges of the technology. Early applications of heap leaching offered a low cost technique to achieve high recoveries from oxide ores, typically greater than 70% depending upon the kinetics of reaction. As world copper resources transition to mainly copper sulfide mineralogy, such as chalcopyrite based ores, achieving high recovery from these copper sulfide deposits is proving more difficult due to the complexity of the leach kinetics, which leads to low leaching efficiency."

Jan 1, 2018

By Donald O. Downing

"IntroductionThis paper provides an overview of the coal mining industry in Canada with a description of current circumstances. The Canadian industry is placed in a global context and the future prospects of the industry are described. The export market is very important to the future of Canadian coal production and the essential aspects of the market are explained. Future prospects are very much tied to metallurgical coal exports and some key characteristics of that market are discussed, including major technological changes in the industry. Stability in 1996The Canadian coal industry enjoyed another strong year in 1996 continuing a trend established over the last four years. The strength of the industry is based on a stable domestic industry and a relatively healthy inter- national market. The figures bear out these statements. In 1996 total production reached 75 million tonnes and consumption was 52 million tonnes. The major markets for coal in Canada are electricity generating stations (Alberta, Saskatchewan, Manitoba, Ontario, New Brunswick, Nova Scotia) and the steel industry in southern Ontario. Approximately 11 million tonnes of coal were imported and exports reached a new record of 34.5 million tonnes, mainly from western Canada. Canadian Coal FlowsCanada represents a unique case in the coal world because we both import and export coal (Fig. 1). The reason for this apparent dichotomy is Canada’s geography. Eastern Canadian coal markets are located closer to the eastern United States coal fields and are basically served by them. This is true for both thermal and metallurgical coal. Major imported coal users are the steel industry, electricity generators and other industry including the cement industry in southern Ontario, Quebec, New Brunswick, with a little coal imported into Manitoba. Only about 2.2 million tonnes of western Canadian coal move into the east, including both lignite and bituminous coal."

Jan 1, 1997