Search Documents

By F. L. Bosqui, A. D. Wilkinson

EVEN though the world has not been crying for more copper for the last three or four years there has been some important mill and smelter construction. Discovery and development of large new high-grade copper deposits in Africa has led to the construction of extensive reduction facilities there, prominent among which is the concentrator and smelter of the Rhokana Corporation at N'Kana. Northern Rhodesia. The 3000-ton concentrator adjoins the central shaft. A little over half a mile to the southeast, at an altitude of 40,010 ft., is the smelter, designed on the site by 1. H. Wynne. It is arranged primarily to treat N'Kana copper concentrates, but can also handle concentrates and direct-smelting ore from outside sources. Excavations were started late in 1930; concrete was first poured on Jan. 6. 1931; and the first blister cop¬per was cast on March 1.9, 1932, less than fifteen months later. During this period, which included several months of heavy tropical rains, some 10,000 cu. yd. of concrete was poured and 41000 tons of structural steel erected under the supervision of construction engineer, A. Ek, with a labor force of 60 to 30 Europeans and about 300 natives. The steelwork was fabricated by Head Wrightson & Co. in England, and the boiler plant equipment furnished and erected by the International Combustion Co. Ltd.

Jan 1, 1934

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By Meisam Ghiasi, Mohammadreza Khalesi, Mahmoud Abdollahy

In the current research, isothermal experiments of kinetic analysis were performed at different temperatures (800–1050 °C) and particle sizes (885 to 10,763 μm) to investigate the calcination kinetics of high-purity limestone. Thermal analyses were carried out in a zirconia crucible, 1 cm in height, for different temperatures and particle sizes. The reaction rate coefficients were varied in the 2.2 × 10−5-1.62 × 10−3-m0.6.s−1 range. Moreover, various isothermal kinetic analysis methods were applied to assess the decomposition mechanism and the calcination function governing the process. The modified shrinking core model was found as the best representation of the high-purity limestone kinetic data. The activation energy was evaluated using the Arrhenius curve, and an average value of 86 kJ.mol−1 was obtained.

Sep 15, 2020

By J L. Stacey

The diverse priorities, drivers and concerns of multiple stakeholders in the minerals industry complicate the integration of sustainable development considerations into mine design, as well as operational and strategic decisions. The ability of the industry to address all role-playersÆ needs, or indeed, to achieve consensus among all role players on the plethora of sustainable development issues seems a noble yet unattainable goal. One of the difficulties in assessing the relative importance of sustainable development issues across many stakeholders is the inevitable lack of impartiality in valuing these issues. Starting from a premise that transparency and fairness of the process are absolute prerequisites for progress, but that consensus is not, an approach has been developed in which all stakeholders are asked to assess the importance of all other stakeholdersÆ priorities, excluding their own. The approach recognises that stakeholders have different levels of contribution, understanding, vested interests, and perceptions of legitimacy and entitlement, across the diversity of sustainable development issues and decision criteria. Using Triangular Value Analysis, the relative weightings of each of the stakeholderÆs priorities are determined through a regression-like technique. The uniqueness of this approach is the manner in which self-assessment bias and overemphasis of stakeholdersÆ own priorities are avoided. The methodology can be used for both internal and external stakeholders, and in conjunction with other group decision making techniques, such as the nominal group or Delphi techniques. This paper will illustrate how Triangular Value Analysis may be applied in the minerals industry to determine priorities in various decisions relating to potentially conflicting sustainable development priorities within the industry.

Jan 1, 2009

In classical drill and blast underground mining methods, especially narrow vein operations economic quantities of broken ore can be left behind following normal mucking operations on the stope floors. The ore left behind can have significant economic value and if not collected can be lost forever. This paper reviews techniques for cleaning this material from stopes that have been used in the past and reviews possible modern techniques that can be applied to ensure this valuable material is removed from the stopes.

Aug 1, 2010

By F. Calizaya

This study summarizes the results of various numerical and laboratory experiments per-formed to study the effect of airflow recirculation on gas concentration. The numerical exercises were carried out on a simulated mine ventilation net-work. The laboratory experiments were conducted at the Mackay School of Mines' airflow monitoring system in Reno, Nevada. In both cases, the airflow was recirculated through the system by means of a main fan and a set of booster fans. The booster fans were positioned to produce two types of recirculation: In line and Cross-cut. For each type, various recirculation conditions were generated by changing the booster fan pressure. During each test, the gas emission rate at the simulated working face was kept constant. The study illustrates the conditions under which controlled airflow recirculation may be used to solve a district ventilation problem.

Jan 1, 1991

By Guo Chen, Xuefeng Liao, Tu Hu, Shengzhou Zhang, Hongying Xia, Jinhui Peng, Libo Zhang

Pine nut shell is as raw material for preparation of high surface area activated carbon (HSAAC) by microwave induced KOH activation. The effects of microwave power, activation duration and KOH/C mass rate (R) on the iodine adsorption capability and activated carbon yield were investigated. Additionally the surface characteristics of HSAAC were characterized by nitrogen adsorption isotherms and SEM. The operating variables were optimized utilizing the response surface methodology and were identified microwave power 738W, activation duration 17 min, and R 4, corresponding to a yield of 46.28 % and an iodine number of 2154 mg/g. The key pore structure parameters of HSAAC such as the Brunauer–Emmett–Teller (BET) surface area and total pore volume were estimated to be 3819 m2/g and 2.09 mL/g, respectively. The findings strongly support the feasibility of microwave heating for preparation of HSAAC from spent pine nut shell by microwave induced KOH activation.

Jan 1, 2016

By J. Kretschmann, H. Mischo, O. Drusche, S. Krause

Mining is and will be inevitable in spite of the increasing implementation of circular strategies. The energy transition and population growth will boost the demand for critical raw materials. It is the opportunity for miners to reinvent their business models. Generating attractive new business cases with sustainability-oriented innovations meets investor and stakeholder expectations from the beginning. This contribution guides managers on their pathway towards sustainable success. Contextual sustainable business model patterns will be presented that can be adjusted individually, regardless of actor’s size. It will also point out, how sustainable value creation can be measured on business model level.

Feb 1, 2023

By S. Gaulocher

Gearless mill drives (GMDs) are the workhorse in the mineral processing industries, more specifically when it comes to grinding crushed ore and cement (in various production stages) in semiautogenous (SAG) mills and large ball mills. They are renowned for their excellent reliability and robustness, long lifespan, and little need for maintenance, and thus yield a low total cost of ownership (TCO). A GMD represents a major investment for a mineral processing plant, and its availability is pivotal for the grinding process. As a basic rule, shut-down periods are to be minimized, but even much more important is that unscheduled shut-downs be avoided. In this contribution, we will present a portfolio of innovative remote diagnostic that consist of the following three key components: 1. Trouble shooting is a form of corrective maintenance and is based on state-of-the art remote access technology, thus enabling highly skilled engineers to access the current sensor readings anytime and from anywhere in order to resolve urgent problems together with the GMD user. 2. Periodic maintenance reports are a form of preventive and predictive maintenance and aim at continuous improvement based on long-term historical records and analyses of multiple measured signals. These detailed reports highlight the health and operational status of the GMD and are periodically (e.g. 3 months) submitted to the customer. 3. Remote condition monitoring spans across preventive and predictive maintenance and is based on continuous recording and automatic analyses of relevant signals using advanced algorithms. The main issue is how to handle the enormous flood of data in an intelligent manner. The results of these analyses are made available to both the GMD user and supplier in real time in order to increase the availability and reliability of the GMD. In this paper, we consider various parts of the GMD, e.g. the cycloconverter, the ring motor, the auxiliary devices (e.g. cooling and lubrication systems), and also phenomena related to the mill itself (e.g. state and quantity of charge). The signal analysis techniques range from simple threshold-based analyses to complex time and frequency domain analyses. We will illustrate the benefits of the proposed approaches with some selected examples.

Jan 1, 2012

The past decade has seen remarkable progress by the railroads both in equipment and concepts in the handling of dry bulk. materials. While such shipments have always been an important part of the traffic handled by the railroads I little was done to improve the efficiency of handling or toward attempted optimization of equipment design before 1960. Several developments at about that time turned attention to this important segment of railroad traffic. One was the construction of a successful coal slurry pipe-line. Another was the promise of substantial economy in electric power transmission by ultrahigh voltage systems and finally, came the growing technological and economic feasibility of nuclear fuel electric generating plants. Each of these developments was a threat to the coal traffic of the railroads --the most important single commodity they handled in terms of revenue and tonnage. By the mid-1950's I Southern Railway management had become most concerned with its growing investment in freight car equipment and the declining revenue productivity of the capital employed. Additionally I there was substantial concern with the loss of business and potential losses in the area of the railroad's greatest economic advantage --bulk commodity movements. In 1958 a small team was established to study this problem. They arrived at two conclusions. The first conclusion was that within limits of maximum gross allowable weight on rail the lowest unit net capacity cost of investment came at maximum allowable gross weight per car unit. The second conclusion was that with a high degree of utilization costs per weight unit transported could be reduced to the pOint where

Jan 1, 1971

By W. J. McKenna

The International Smelting Co. concentrator at Tooele, Utah, first operated on a custom basis for the treatment of lead-zinc-iron ores on Nov. 1, 1924, with a capacity of 500 tons per day. On May 1, 1925, the capacity was increased to 1000 tons per day by the addition of another 500-ton section. The concentrator has since operated on the two-section basis, each treating 500 tons per day entirely by flotation. Laboratory and Test Mill In connection with the concentrator, a well-equipped laboratory and small continuous testing plant are maintained. The flotation equipment in the test plant is of both the Callow and Mineral Separations Sub-"A" types, so that actual concentrator conditions may be duplicated as closely as possible. Purchasing of Ore A new shipper usually sends to the plant a 25 to 50-lb. samplc, representative of the ore to be shipped. Batch flotation tests are made on this sample to determine its amenability to the concentrator treatment flowsheet and reagent combinations. The results of these tests, which are accurately correlated with those obtained at the concentrator, both as to grades of products and recoveries, determine the actual value of the ore as submitted in the ore purchasing department's treatment schedule. Hearty cooperation has existed at all times between the ore purchasing and operating departments in the selection of ores as conccntrator feed. Ores Treated The basic tonnages for mixtures on the two sections come from the Park City and Bingham mining districts. The Park City tonnages arc received by rail and consist of crude ores and gravity mill products. Those from the Bingham district arc received by rail and aerial tramway,

Jan 1, 1928

By S. P. Sandoval

The U.S. Bureau of Mines investigated the separation of aluminum from copper dump leaching liquors using a supported liquid membrane. Aluminum was selectively transported through porous polypropylene impregnated with di (2-ethylhexyl) phosphoric acid in an aliphatic diluent. The effects of variables, such as solution composition, temperature, and extractant concentration, were measured with a three-level fractional factorial experimental design. Experimental results were used to derive equations for predicting transport rates for aluminum, iron, and copper. The major variables influencing aluminum transport were solution temperature, feed solution pH, aluminum concentration in the feed solution, and extractant concentration. Copper and iron transport rates were almost zero when aluminum transport rates were high. Measured aluminum transport rates under the best conditions of 55° C, pH 3.0, 16 g/L A13+, and 65 pct extractant solution confIrmed the predicted value of 210 f.'g/(cm2.h). Transport rates for iron and copper were less than 5 ug/(cm2.h) under these conditions. Aluminum was recovered from the stripping solutions by sparging with gaseous hydrogen chloride to crystallize aluminum chloride hexahydrate, which was calcined to alumina. Sparging crystallization regenerated the stripping acid for recycle.

Jan 1, 1989

By R. B. King

This document was prepared by the DFI International Grouting Committee with the intent to provide a summary of main Standards and Guidelines available for the North America and Europe grouting industry. This document highlights the different approaches, methods and tools used internationally. The DFI International Grouting Committee comprises all parties involved on a grouting project: Owners, regulators, engineers, contractors, and manufacturers (equipment and materials). This document is not intended to cover every conceivable application or requirement of grouting. However, it does provide standard practice requirements for qualifications, materials, equipment, testing, and production procedures for the professional engineer to incorporate into their project specific requirements.

Jan 1, 2021

By Edward L. McHugh

The appraisal of mineral resources of the Challis National Forest, Idaho, by the U.S. Bureau of Mines, was made so that the mineral resources of the forest could be appropriately considered in land use planning. Information from this study is intended to help the U.S. Forest Service to incorporate mineral resource data into forest plans. The study was done in conjunction with the U.S. Geological Survey, which released a companion report on the geology and mineral potential of the Challis National Forest in 1989. Mineral development activity in and under the Challis National Forest has been of great economic significance to Idaho and the United States. Since the 1960's, mines within the forest have produced mineral commodities worth more than $590 million A current (1989) commodity prices. Identified mineral resources have a gross value of about $2 billion at current prices, including 8 strategic or critical minerals. The U.S. Bureau of Mines study identified and described 723 active and inactive mineral properties within the forest. Mineral properties with identified resources were evaluated to determine their economic significance, and an assessment was made of the feasibility of mineral development. Of the 2,516,191 acres in the Challis National Forest, about 390,000 acres were classified as having mining development interest commercially important mineral production, mainly of molybdenum, gold, and silver from the Challis National Forest is likely for the foreseeable future.

Jan 1, 1991

By Bonifacio Degay, Mike Lovitt

PT Freeport Indonesia is a block cave mine that now utilizes an advanced undercut method to set up the min in the Deep Ore Zone (DOZ). In this method a slice of rock (undercut) is broken such that it sits on top of the drawbell level. The drawbells are developed to channel the broken ore into the extraction level and to enable the caving orebody to be drawn out in an even and controlled manner. These drawbells are difficult to form due to the small amount of void that can be developed in the low strength rock before firing. Starting with two rises of 2m square, the void ratio for the entire drawbell around 6%, which would normally result in a frozen and unproductive blast. Orica -Mining Services have worked with PT Freeport in a collaborative effort to find a solution to the mining problem. With excellent control of timing of the blasting it is possible to get fluid flow of blasted rock out of the draw points such that more void can be made available for blasting the remaining parts of the drawbell. The i-konTM electronic blasting system gives the exacting control of timing within the blast to achieve this Dynamic Void Generation (DVG). The solution stops the need to charge close to brows in the drawbells and reduces the cost and time related to developing initial blast voidage. This paper identifies the results of the trials including design, photographic evidence and vibration analysis. The flexibility and accurate timing of this electronic blasting system has enabled single hole initiation rather than 4 or more holes being initiated together, thereby reducing the damaging vibrations to the extraction level.

Jan 1, 2004

By D. G. Kesterkel

Low-melting thoriurnrbase binary alloys or metal solutions were prepared by two different techniques involving the electrolysis of ThO2 dissolved in fluoride melts. Experiments were performed at 950° to 1,250° C using electrolytes containing ThF4 and various alkali and alkaline earth fluorides. In the first method, electroreduction of ThO2 and deposition of thorium on a nickel or iron cathode formed a molten alloy that dripped off and collected on the bottom of the cell, or in a tungsten cup. An electrocodeposition technique was used to prepare thorium-base alloys or solutions containing nickel, iron, chromium, or manganese. Electrolytic reduction of the component metal oxides and simultaneous deposition of the two metals on a tungsten cathode yielded a liquid alloy product. Complementary experiments were performed on the fused fluoride electrowinning of dendritic thorium from Th02 at 1,075° to 1,200° C in which thorium crystals were recovered and arc-melted into buttons. Major contaminants were aluminum, carbon, copper, iron, oxygen, and silicon, totaling 0.2 percent.

Jan 1, 1966

By Jiachen Wang

China is the largest coal producing country in the world. Coal is widely distributed in China and thus the mining conditions are complex and diverse. This paper summarizes the important achievements in the last 20 years in various mining methods including the extra thick seam with large mining height top coal caving, the thick seam with large mining height and top coal caving mining, the steep seam with top coal caving and fully-mechanized mining, the thin seam automated mining, and the backfill mining. At the same time, the rapid advance in the development of mining machinery and manufacturing has also contributed to the advancement of coal mining technology and the great improvement of coal mine safety. The future direction of China?s coal mining is to further improve mine safety as to improve the coal recovery rate, promote the pillar less mining technology, develop high-efficiency backfilling technology, develop steep seam high-efficiency mining technology for seams less than 10m thick, and high recovery mining techniques for extra thick seams, improve the reliability of mining equipment, and strengthen the protection and restoration of surface environments and water resources.

Jan 1, 2014

By A. Vilinska

The adhesion of Leptospirillum ferrooxidans bacterial cells onto the sulfide minerals pyrite and chalcopyrite was evaluated using two different physical-chemical approaches; thermodynamic and extended DLVO theory. For the parameters incorporated into calculations, the zeta potentials and contact angles of powdered solids and bacterial cells were acquired experimentally. The Hamaker constants essential for Lifshitz-van der Waals inter-action calculations were calculated following two different methods: macroscopic and microscopic. Adsorption tests were carried out at physiologic conditions to estimate the amount of cells adsorbed onto a mineral surface and the extent of alteration of that mineral surface in biobeneficiation. The free energy of adhesion was found to be negative for both minerals, indicating that the adhesion is energetically favored and preferred. The interaction energy diagrams of the total interacting force was also negative for the cases where the particles were charged oppositely; in the remaining cases, the total force was attractive after overcoming an energetic barrier caused by the repulsive electrostatic forces. Under the conditions of the adsorption test, the experimental results are in agreement with the theoretical; this suggests that the physical-chemical forces are crucial for bacterial adhesion.

Jan 1, 2011

By T. J. White

Each year, thousands of tons of toxic concentrates are produced as the unwanted byproducts of industrial operations and smelting activities. The fate of these materials remains open, as in general their consumption is limited and potential markets contracting. Xtaltite (pronounced crystal-tight) is a Synthetic Mineral Immobilization Technology (SMITE) optimized for the concentration, detoxification and consolidation of toxic metal wastes. In this approach, we seek to mimic nature to produce durable synthetic minerals that survive for aeons in well characterized geological settings. This approach has high public acceptability because the concept is easily understood by the layperson and the long term stability of the waste form may be predicted with confidence. In addition, where Xtaltite is used for mine backfill, a system of ecologically sustainable mining development is established. This paper details the design and fabrication of Xtaltite under oxidizing and reducing conditions. To illustrate and contrast these stabilization regimes, specific reference will be made to the treatment of thallium, chrom~um and arsenic wastes. Waste form performance under TCLP, dynamic boiling water tests and in other leaching media will be compared and discussed with respect to their relevance to different disposal options.

Jan 1, 1995

By P. R. Bradley

This paper is one of a series , dealing with mining methods and costs , sponsored and published by the U. S. Bureau of Mines . Papers of this series are written by engineers and executives of mining companies , at the solicitation of the Bureau , and in accordance with an outline prepared by Bureau engineers , for the purpose of securing uniform presentation and conformable data . The property of the Alaska Juneau Gold Mining Co. is situated near the city of Juneau , Alaska , in what is known as the Harris mining district . Wholesale mining operations have been adopted on a large scale and 10,000 to 11,000 tons per day of gold- bearing ore are mined and sent to concentrators near Juneau . In addition to gold , the ore yields 0.6 ounce of silver and 13.0 pounds of lead to each ounce of gold recovered .

Oct 1, 1929