Search Documents

By James F. Neill, O&apos

Brown iron ore resources in Barbour, Butler, Crenshaw, and Pike Counties were investigated in a drilling program and geological study by the Federal Bureau of Mines in cooperation with the Alabama Geological Survey and the University of Alabama. The aggregate footage drilled was 18,010 linear feet. When developed, reserves of 12,664,000 long tons of crude ore were indicated, containing from 26.9 to 29.0 percent iron and 0.2 to 1.6 percent manganese under a maximum overburden of 40 feet. Total inferred crude ore for the four counties was calculated to be 827,700,000 long tons. Beneficiation of samples by simulated log washing and use of a 118-inch screen yielded from 46.8 to 51.7 percent iron and 0.2 to 2.6 percent manganese. Screen-test studies indicated no appreciable interlocking between the iron and manganese minerals and the waste particles of materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size. While an indicated 2,198,000 dry long tons of usable iron ore can be recovered, sink-and-float tests show that it may be possible for 4,654,000 dry long tons to be recovered by other than log washing. However, applicable commercial processes have not been demonstrated.

Jan 1, 1965

By I. S. M. K. Ilankoon

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behavior is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. Previous modeling of this system has used equations from oil and ground water flow to model these systems, but the applicability of these models with the larger particles found in typical heaps is suspect as these systems are not necessarily capillary dominated. In particular, as the characteristic particle size goes from below to above a few centimeters, the flow changes from capillary to gravity dominated. This means that typical heap leaching heaps cover this interesting, but complex, transitional fluid flow regime. In this paper a set of experimental studies of this flow, including PEPT (positron emission particle tracking) based tracer experiments, highly accurate liquid holdup measurements and axial dispersion experiments using salt tracers will be presented. In this study, flow through mono-dispersed particle beds was carried out. In particular, the hysteresis in the liquid holdup as the liquid flow rate into the particle bed is varied is investigated, since this hysteresis means that the relationship between flow rate and holdup is history dependent, an effect not included in models currently used to describe fluid flow in heaps. A theoretical model that describes this hysteresis will also be presented. Keywords: heap leaching, hydrometallurgy, modeling

Sep 1, 2012

By Berger. P.

The accepted definition of the function of an edge protector fails to specify adequately the several tasks which it must perform to be functionally effective: detailed analysis of these tasks leads to the reasoned conclusion that they cannot satisfactorily be fulfilled by the conventional types of "edge-strips". The true cost of edge protector failure is cumulative: renewal costs are dwarfed by the increased operating expenses and production losses which result from but partial or incipient failure of the edge-strip; yet, the several supposedly improved types, for use with starter-blanks, generally were "built down to a price", prolonging the agony, as it were. Clearly, a fresh appraisal of the problem was overdue, and more especially so with the advent of "permanent" cathodes. As a result, new methods of edge .protection have been developed, including the so-called "EDGEWISE" system in which the present author as patentee *) has a vested interest-which he hereby declares. Due mention is made of recent progress in protecting the edges of aluminium "Jumbo" cathodes in zinc electrowinning operations, although the present Paper is more concerned with edge protection of starter-blanks and permanent cathodes in copper ER/EW processes, where most of the "old" problems now may justifiably be claimed to have been overcome, Mention is also made - albeit at this time necessarily only briefly, and confined to edge protection - of "rigidized" metal blanks and permanent cathodes: a most recent development**) which may prove to represent a "breakthrough": time will tell.

Jan 1, 1987

By AIME AIME

THE Iron and Steel and Institute of Metals Divisions will meet jointly at the Statler Hotel, Detroit, Oct. 4 and 5, during the Metal Congress, Oct. 2-6. The Wire Association, the American Welding Society and the American Society for Steel Treating, together with the two Divisions of the Institute, constitute the Congress this year, and each body offers an interesting technical program. The National Metal Exposition will, as usual, be held concurrently. Visiting metallurgists will find themselves engaged in a bit of research not listed in the program-a time study of how best to exploit in a few days both the Congress and all that the place of meeting has to offer. For Detroit, the beautiful "City of the Straits," is third in rank industrially in the United States, and its great manufacturing plants offer much of metallurgical interest. This is especially true of the automobile plants which will be open to members of the various societies during the week of the Congress.

Jan 1, 1933

By William O. Vanderburg

Tis paper describing the mining practices at the Cold Springs mine of the Wolf Tongue Lining Co. at Nederland, Colo., is one of a series of similar papers prepared by the Fureau of kines on mining practices, methods, and costs at various mines in the United States. The writer acknowledges the assistance of William Leach and William T. Todd, manager and mine superintendent of the Wolf Tongue Mining Co., respectively, in the preparation of this paper.

Dec 1, 1932

By A. E. Ketler

This report describes a variety of coal mine lighting projects which were funded by the Bureau of Mines in order to obtain underground lighting experience in support of new lighting requirements for underground coal mines. Low coal and high coal, narrow and wide entries, conventional and continuous mining, ac and dc power, bituminous and anthracite, and machine mounting and area lighting were some of the variables covered in this program. Also evaluated was the OCENCO fluorescent caplamp.

Jan 1, 1979

By E. H. Mohr

AT the McGill concentrator of the Nevada Consolidated Copper Co., all flotation operations have been carried out in Forrester cells since November, 1926. In respect to cost of operation, the new cell has proved to be superior to the Callow, which it supplanted, and its incorporation in the flow sheet has resulted in a marked improvement in the metallurgy. Before citing the advantages of the new machine over the old, it should be explained that the Forrester has not only replaced the Callow, but it has made possible the elimination of a number of tables as well. When Callow cells were in use, table concentration preceded flotation. The ball mill pulp was elevated, by means of air lifts, to roughing Wilfley tables situated two floors directly above the flotation floor. On an intermediate floor were additional tables which cleaned the concentrate from those above. The finished table concentrate constituted approximately 60 per cent. of the total mill production, and contained about 40 per cent. of the recovered copper. The table tailings were returned to the classifiers, the overflow from which went to the flotation cells and the oversize to the ball mills. As soon as the Forrester cells were installed, this tabling operation was discontinued. The ball mill pulp now discharges into the classifiers direct, without the intermediate tabling. It was impracticable to employ the present flow sheet when Callow cells were in use, for the reason that unless the greater part of the heavy mineral was first removed, it accumulated on the mats and adversely affected the flotation operation. By tabling ahead of flotation, it was practicable to maintain the concentrator at 10 to 20 per cent. greater capacity (depending upon the pyrite content of the ore) than was possible by flotation alone. This was due to the necessity for finer grinding in the latter case. Even though the table concentrates contained only 6 to 8 per cent. copper content, the low smelting costs made it advantageous to operate at high mill capacity, at the cost of low grade of product.

Jan 1, 1927

By Robert A. McColly

This Bureau of Mines report compares the availability of federally owned minerals in Arizona with lands considered favorable for discovery of mineral resources, to deter-mine the extent to which Federal mineral lands in such areas have been withdrawn by legal action or restricted by management practice. Of particular concern are restraints on Federal lands in areas identified as highly favorable for occurrences of valuable mineral deposits. Excluding Indian lands held in trust by the Federal Government, about 32 million acres, 44%, of Arizona's mineral estate is federally owned. This total includes lands with partial Federal mineral ownership. Approximately 16.5 million acres, or 52% of these lands, are available for location or lease. This includes 496,000 acres, 62%, of the lands highly favorable, and 2.6 million acres, 57%, of the lands moderately favorable for locatable minerals in Arizona. All other Federal mineral lands are either withdrawn or restricted, reflecting a wide range of purpose, authority, and impacts on mineral exploration and development.

Jan 1, 1987

By J. B. Dorsey, T. W. Brinkley

Performance of a high-pressure, vaporizing gas-drive project in a volatile oil reservoir is discussed. The project has been in operation for over 8 years. Present recovery from the over-all displaced portion of the reservoir is 40 percent, and an ultimate recovery of 60 percent is indicated. Calculations reflect an over-all displacement volume of 50 percent for the entire reservoir; therefore, ultimate oil recovery will be 30 percent of the entire reservoir oil originally in place. Laboratory vaporization tests conducted prior to project initiation also are presented and discussed, along with an analytical method of determining stock-tank oil production and gar injection requirements related to over-all volumetric displacement efficiency from these data. Introduction The Shoats Creek field is located in Beauregard Parish, La., in the extreme western part of the state (Fig. 1). Discovered in 1956, the field is productive in three Cockfield sand zones, ranging in depth from 8,000 to 9.000 ft. The upper two zones, 1st and 2nd Cockfield, are condensate-bearing gas reservoirs. The lowest zone, the 5th Cockfield, is a volatile-oil reservoir. Laboratory work conducted on crude oil from the 5th Cockfield zone shortly after field discovery demonstrated that, when contacted with dry gas, signidcant volumes of the oil could be vaporized at reservoir temperature and at an appropriately high reservoir pressure. Further study led to the conclusion that early initiation of a crude vaporization project in the 5th Cockfield zone would be superior economically to other methods of reservoir depletion. Consequently, the zone was unitized and gas injection operations started late in 1958. This paper discusses laboratory work performed in conjunction with the project, and project performance to the present. History of Development The 5th Cockfield zone in Shoats Creek is composed of a thin, very shaly, low-permeability sandstone. Oil accumulation is controlled by a structural trap bounded by faults along the north and west and by a water contact on the southern boundary (Fig. 2). The zone covers a productive area of 1,550 acres at an average depth of 9,000 ft. The net sand section is thin, having a maximum thickness of 10 ft and an average thickness of 5.5 ft (Fig. 3). Average reservoir rock properties, as determined from core analysis are presented in Table 1. Shaliness of the zone is illustrated by the typical electric log of the 5th Cockfield section in Fig. 4. Because of the thinness and poor quality of the sand, the 5th Cockfield was developed on a wide spacing. Eleven completions were made in the zone between 1956 and 1961 for an average density of 140 productive acres per completion, with the majority of wells being dually completed in the 2nd and 5th Cockfield. Average initial potential for producers in the 5th Cockfield was 130 BOPD. Oil from the 5th Cockfield has a stock-tank gravity of 50.5" API; with a bubble-point pressure of 3,515 psia, the oil was highly undersaturated at the original reservoir pressure of 4,675 psia. Pertinent properties of the oil as determined in the laboratory are presented in Table 2. Because of the volatile nature of the crude, laboratory studies of its susceptibility to vaporization, as well as a vapor-liquid phase study, were conducted in addition to a standard PVT analysis. The vaporization study was conducted in a visual cell; a stepwise illustration of this work and laboratory measurements are presented in Fig. 5. Field

Jan 1, 1969

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"The Copper Mountain Mine is located in Princeton British Columbia, Canada and produces 80 – 90 million pounds of copper annually, as well as gold and silver by-products. The ore processing plant has a conventional SAG/ball mill circuit with inline pebble crushing, followed by flotation. At most plants, much time is spent evaluating and optimizing the comminution and flotation circuits. The cyclones are a key contributor to the effective operation of the plant: They define the circulating load in the comminution circuit and provide the classification that ensures liberated material is passed through to flotation. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput in flotation. For such an impactful unit operation, cyclones have historically been under-instrumented. Consider as well that the cyclones are typically located at the highest elevation in a plant, and it becomes clear why they often underperform. Copper Mountain Mine recognized the critical role that cyclones filled in their plant and worked to optimize their operation through the implementation of a Portage Cyclone Detection (PCD) system to identify plugging and roping incidents, Portage Pumpbox Control (PPC) to manage the flow to the cyclones, and AwaRE to control the grinding circuit. As a result, cyclones overflow stability has increased, switching out a roped or plugged cyclone now happens within seconds rather than many minutes, and both the grinding and flotation circuits perform better. INTRODUCTION Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. The cyclones are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations. The cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance to have proper stability in cyclone operation while implementing any plant-wide optimisation strategy."

Jan 1, 2015

By Lina Chica, Arturo Barrientos, O. Bustamante

Hydrocyclone is a device commonly used in mineral processing industry. Underflow control plays a fundamental role in hydrocyclone operation. This affirmation supports the fact that hydrocyclone underflow has effect in some aspects of separation performance like capacity, split ratio, cut size and bypass. Hydrocyclone operation state is associated to underflow characteristics: air core formation and discharge shape. Many studies attempt to understand size separation phenomenon and the discharge influence but none of them has taken an energy point of view. This work presents the results of a mechanical energy dissipation for hydrocyclone operation from a mechanical energy balance. The experimental results related to Newtonian suspensions show that underflow energy dissipation does not control the operation because this magnitude is small compared to interior energy dissipation. However, discharge energy dissipation provides enough information to describe underflow conditions and its influence in separation conditions. In the modelling non dimensional parameters have been considered for hydrodynamic description and for geometrical and operation hydrocyclone characteristics. Energy dissipation from the continua media approximation results into a relevant concept to understand the hydrocyclone performance and improve industrial installations.

Jan 1, 2014

By Arthur E. Morris

The primary market driver for improving process technology is innovation, which requires a skilled and educated workforce. However, many Materials Science and Engineering departments have eliminated extractive metallurgy and chemical thermodynamics from their curricula, yet these topics contain the necessary fundamentals for process innovation. As a result, most MS&E students are ill-prepared for careers in processing. The dearth of processoriented MS&E curricula has prompted some Universities to develop a “shared” effort to offer distance education between multiple institutions [1]. A target audience for a shared process simulation course would not only benefit students, but also be a basis for an on-line course for practicing engineers faced with new or changing career choices. To fill the gap, the basics of a process simulation course was developed in an abbreviated form as series of eleven articles and Excel workbooks published in Industrial Heating magazine between July 2012 and July 2013.

Jan 1, 2014

By Stephen Benyo

The future of mining will not be defined by how deep operators dig, but by how intelligently they separate. As ore grades decline, environmental concerns intensify and water remains a global crisis, the industry is discovering that its greatest opportunities for progress lie not at the pit or face, but downstream — within the separation processes that govern water, tailings and byproduct streams. In this context, clarity has become a defining principle — both literally and metaphorically. Clear process water enables reuse and regulatory compliance. Clear separation of solids and liquids recovers valuable resources, supports safer operations, lowers energy demand and provides stable tailings management. Clear visibility into how these systems perform allows mine operators to make better decisions, reduce operational risk and unlock value that is often hidden in overlooked waste streams.

Apr 1, 2026

By Volovik A. V. Ivtan, Shelkov E. M. Ivtah

"One of the most power consumption Industrial process is production of Al from bauxites (about 45000KWt.hour electrical energy for production of 1 ton. of technical Al). This process is based at the low efficiency and productivity electrolysis technology.Last years IVTAN investigations give to .us information about possibility to use of high temperature shaft- furnaces for efficiency production of alumina (AL2O3 ) technical. aluminium and some all.oys on the base of the high temperature carbon- thermal reduction process. At this case power consumption for production of unit of last, product will be less at the 3-4 times.The carbon-thermal method is allow produce alumina (Al203 ), technical Al and its alloys not only from deficient bauxites, but practically inexhaustible reserve of other types of Al-contain row materials (cianite, sillimonite and so on/The thermal-chemical economical analises of fulfilled at the IVTAN, production of alumina. Base on facts of production and technical technology are especially for ones arguments at the high temperature shaft-furnace technical Al and its alloysIn the last decades of the 20-th century, the discharge into atmosphere of high temperature and. combustion gases places . problems before humanity more and more sharply and becomes of great importance task.But at the same time, as production of material values increases, intensity of pollution of environment increases all time. And the value of new processes and. technologies of material production, aimed at reducing the expenditure of power and pollution of· the environment, also increases."

Jan 1, 2000

By William J. Lang

In just over a generation, the United States bentonite industry has grown from almost a rake and shovel operation into one with a multimillion ton annual production rate and exports to all corners of the globe. Bentonite production, pressed to keep pace with the soaring demand, has increased more than 10 fold in the last 30 years. The worldwide demand for bentonite is expected to double during the next eight to ten years. It remains to be seen whether U.S. producers will be able to maintain the dominant position in the world market. It should be noted that accurate statistical information regarding production or market information is difficult or impossible to obtain abroad and also within the United States. Published information obtained in response to questionnaires of the Bureau of Mines tends to be on the conservative side. FOUNDRY It has only been in the last thirty or forty years that bentonite has become an indispensible part of the age old metal casting industry. The relationship has proven most beneficial to both industries and promises to be long lasting. The foundry market for bentonite was the least of the three major markets twenty years ago but now leads all others and consumes 1/3 or more of the

Jan 1, 1971

By E. T. Pecina

Bioleaching is a viable option for the processing of auriargentiferous refractory ores with high arsenic content. The application of mesophilic (A. ferrooxidans and ?L. ferrooxidans?) and thermophilic bacteria of the genus Sulfolobus (S. solfataricus and S. acidocaldarius) as oxidant treatment before the cyanidation of an industrial arsenical pyrite concentrate is presented. The results show that extraction of gold and silver increases due to bio-oxidation caused by mesophilic bacteria and results in a maximum gold recovery of 68%. In all strains studied, biooxidation resulted in an average silver recovery of 50%. The results showed that all evaluated strains were sensitive to solids content (5 to 20%) and average particle size (75 and 38 µm) of the concentrate.

Jan 1, 2010

By James F. O?Neil

Brown iron ore deposits in Quitman County, Ga., were investigated by the Federal Bureau of Mines in cooperation with the State of Georgia, Department of Commerce, and the University of Alabama. Ninety-one holes were drilled, having an aggregate footage of 2,188 feet; seventy-one holes penetrated 248 feet of iron mineralization. Average thickness of the ore zone was 3.5 feet under an average thickness of 14.7 feet of overburden. The drilling developed inferred reserves containing nearly 30 million long tons of crude ore with an average analysis of 28 percent iron plus minor quantities of manganese. Test work done by the Bureau on the crude ore samples indicated that they would upgrade by current lug washer practice, with the use of a 1i8-inch screen, and yield 4.4 million dry long tons of concentrate with an average analysis of 52.1 percent iron plus manganese. The weight recovery obtained was 14.7 percent. Research studies made by the Bureau showed that the weight recovery would be increased by changing the screen size without any appreciable sacrifice of grade. The average weight recovery was increased to 18 percent with a 10-mesh screen and 22.8 percent with a 20-mesh screen. Screen tests studies indicated that there was no appreciable interlocking of the iron and manganese minerals and the clay and silica waste particles of the materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size.

Jan 1, 1965

By P. Amelunxen

Over the past several years, the combination of higher energy and steel costs and the recent commercial deployment of high-pressure grinding rolls (HPGR) technology in hard rock mining have led many multinational mining companies to evaluate the suitability of HPGR technology for their particular comminution circuits. HPGR technology is perceived to require a higher capital investment while delivering lower long-term operating costs. This paper undertakes a critical evaluation of this perception. By evaluating the capital and life-of-mine operating costs of competing circuit designs for soft, medium and hard ores, the HPGR break-even point can be identified, at which the incremental capital cost of an HPGR circuit is equivalent to the net present value of the projected operating cost reductions. For ores with hardness parameters above the break-even point, HPGR circuits could offer economic benefits, while for softer ores, SAG mill/ball mill/pebble crushing (SABC) circuits are likely to be more economical and energy efficient. This evaluation considers both an SABC reference circuit and a traditional stage crushing configuration. Other influential factors are also discussed.

Jan 1, 2011

By Randy R. Williams, Roberto R. Olivera, Brian W. Wilson, Marina S. W. Li

"An extensive, deep mixing (DM) ground improvement program using the Cutter Soil Mixing (CSM) technique was designed and constructed in 2013 to support up to 20 m (66 ft) high Mechanically Stabilized Earth (MSE) walls and bulk earthworks for the development of the Kitimat Liquefied Natural Gas (LNG) facility at Bish Cove, British Columbia. The deep mixing program consisted of overlapping rectangular panels of in situ cement treated soils, constructed using the CSM technique, to form barrettes covering an area of approximately 12,900 m2 (15,428 yd2) and providing suitable static and seismic stability of foundation soils for support of the proposed MSE walls, which would in turn support LNG facilities. The deep mixing program comprised of 1645 CSM panels that were constructed through varying thicknesses and discontinuous layers of very soft fine-grained marine deposits and/or loose sandy silt to silty sand deposits, embedding typically 2 m ( 6.6 ft) into dense silty sand to sand and gravel. CSM panel depths ranged from 5 m (16 ft) to 30 m (98 ft) and were constructed by treating approximately 73,900 m3 (96,658 yd3) of soil yielding average unconfined compressive strengths exceeding 2.5MPa (363 psi).This paper outlines the approach adopted for the design of the CSM ground improvement program in the highly variable subsurface conditions present at the site. A phased sitespecific investigation consisting of boreholes, test pits, Cone Penetration Tests, piston tube sampling, advanced laboratory testing and groundwater monitoring was implemented. In addition, soil-cement bench scale testing was completed, followed by installation of 8 CSM panels for field trial purposes. Extensive geotechnical static and seismic analyses including Limit Equilibrium stability analyses, liquefaction assessments, and advanced numerical modeling were undertaken to optimize the design and meet the project-specific design performance criteria. The Design-Build team worked closely to develop and implement Quality Assurance and Quality Control plans and managed significant construction challenges while achieving suitable panel termination depths."

Jan 1, 2017

By M. Ploc

The grinding process in the mining industry has seen an increased throughput to accomplish greater production and lower overall production costs. Up to 8-9 MW, a single motor can be connected to drive the mill through a pinion and ring gear. Above the single-pinion drive limit, the dual pinion approach was developed to allow two drive motors to be used. This allowed the mill input power to be increased to 16-18 MW. Recent developments in clutch and ring gear materials and design are allowing greater input powers of up to 20 MW to be considered. To avoid damage to the ring gear by uneven load sharing between the two motors, it is critical that the two machines accurately share load. This is typically achieved by either drives capable of controlling load torque between motors or using a GE proprietary control system that accurately controls the load torque from each motor.

Jan 1, 2010