Search Documents

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By Richard E. Ray

Conventional concrete block plastered with a cemantitious coating is the most common material used in the construction of perma¬nent stoppings to direct airflow in underground mines in the U.S.A. All mines experience various degrees of strata convergence depending upon depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting in significant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating "Max-Seal" polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased several-fold in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1984

By L. F. Heising

The Bureau of Mines evaluated 42 composite samples from selected Michigan-Wisconsin iron formations by reductive roasting-magnetic separation and flotation at minus 325 mesh. Samples having poor to marginal response on initial examination by conventional methods were reevaluated by finer grinding, by reagent suite modifications, and by selective flocculation-desliming techniques. Results ranged from excellent on Menominee Range samples to relatively on Gogebic Range ores. Marquette Range samples ranged from responsive to nonresponsive, depending upon grain size and mineral association.

Jan 1, 1967

By D. Randall Crooke, Ron R. Jorgenson

Many coal combustion products (CCPs) have historically been unsuitable for placement as mine backfill because of their physical and geochemical properties and/or regulatory status. However, innovations in paste production and transport of CCPs utilizing the high, fine particle contents of these fine-grained waste materials and their water retention colloidal properties produce a non-segregating, self-cementing material that may be environmentally suitable for placement as mine backfill. Both industry and the regulatory agencies are enthused by the possible cost reductions, both in design and construction of disposal sites, and the reduced environmental impacts of CCP realized by implementation of this new use/disposal technology.

Jan 1, 2001

By R Chandramohan

Comminution is the science of size reduction of brittle materials. It is integral to mineral extraction and is one of the most energy intensive processes in the mining industry. There are a number of tests used to quantify the strength of ore, which are then used to size the AG / SAG mill in circuit design. The calculated energy utilized for breakage in these devices is based on the assumptions that the materials treated are of average shape and that the processing equipment is designed to break the ore as efficiently as possible under the given operating conditions. In drop weight tests, it was found that shape significantly influences the measured rock strength. Controlled experiments with variations in blends of rock shape show that mill throughput increases with the addition of weaker shaped rocks.

Jan 1, 2012

By Donald P. Schlick

This report presents a representative cross section of methods success- fully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

By Edgar T. Gregory

A quiet revolution has taken place in the conveyor belt industry, Man-made materials, improved production facilities, better splicing techniques and emphasis on repair and maintenance have all contributed substantially to lowering material handling costs for the mining industry, It wasn't too many years ago that the rubber industry had only cotton for a belt carcass and tree grown rubber for the protective cover. Then came the development of monofilament rayon. This material had desirable elongation and elastic properties and was the first synthetic fiber to be used in place of cotton. But wet strength and other limitations restricted its use, and the conveyor belt industry turned to nylon. Initially, nylon was considered suitable only for the cross threads or filler threads of a belt carcass. Then technical advancements in heat setting and fabric weave created a major change in belt construction. As a result of these advances the industry was able to take advantage of the full tension strength of nylon cord. Another breakthrough in the use of synthetics was the tremendous increase in adhesion resulting from a chemical bond, rather than the limited physical bond available with cotton. But the advantages of nylon had a more Car-reaching effect, We were able to design a two-ply nylon belt that did the work of a four- or five-ply cotton or rayon belt. A six-ply nylon belt now replaces a twelve-ply cotton elevator belt. Arid nylon resists moisture, acid and mildew, It also has excellent resistance to impact and can be produced with controlled elongation and elastic properties that work to great advantage in reduced-ply belt constructions.

Jan 1, 1971

By N Gruber

In the continuous casting of ultralow carbon (ULC) steels, free carbon is used to control the melting behaviour of mould powders. If the carbon is not completely removed during melting, it is enriched at the top of the slag pool. Liquid steel may come into contact with this layer because of the turbulence of the molten metal, resulting in its recarburisation, which negatively affects the desired product quality. Thus, a reduction in carbon input is desirable. For this purpose, SiC and/or Si3N4 with and without antioxidants were selected as melt-control additives to replace carbon in the mould powders. Thermodynamic calculations were performed to quantify their effect on the melting behaviour based on the chemical composition of a flux already applied to ULC steels. To experimentally assess the liquefaction behaviour, laboratory mould powders were prepared and annealed in steel crucibles closed with a lid. Crucibles were inserted into a furnace that was already preheated to selected temperatures between 900–1200°C for 10 mins and quenched to room temperature. Subsequently, the samples were mineralogically investigated. The results confirmed those obtained from the thermodynamic calculations. Si3N4, and SiC in particular, are suitable raw materials for delaying the solid-solid reactions of raw material components during melting. Owing to their stability at high temperatures, the necessary SiO2 content to form a liquid phase is not available, resulting in lower amounts of the liquid phase. The addition of antioxidants to delay the oxidation of SiC further reduces this positive effect. Attempts to decrease the SiC content without negatively affecting the melting behaviour resulted in a reduction in the CO2 emission by at least 27 g CO2/kg of mould powder when compared to the carbon-containing standard mould powder. These investigations revealed differences in the melting behaviours of granules and loose powders, which are related to their respective production processes.

Jun 19, 2024

By Manuel Gomez

Coking time was investigated as a function of coal properties, carbonization parameters, and the interactions between these variables. The results indicate that coal properties and carbonization conditions interact to influence the coking time, and these interactions may be determined quantitatively. Prediction equations were developed and used to simulate the effects of bulk density, flue temperature, and oven width on coking times for coals having a wide range of properties. The data presented provide additional information on the carbonization process to permit the coke oven operator to maintain closer control of coke production and coke uniformity.

Jan 1, 1968

By R Hargreaves, T Elkington, W J. Shaw, G W. Booth

Every day, around the world, thousands of tons of ore are loaded onto ships completing the miningproduction process and starting a multimillion-dollar economic transactions process. These transactions are based on the supply of tons of a commodity with certain specifications of assays of the main element (or physical properties) and concentration of contaminants, which are finally verified and evaluated by buyers, and also are considered ‘as true’ during Reconciliation process. On Sample Stations, this ‘true’ is based on a few kilograms of sample, often representing thousands of tons, that are sent to laboratories for further sample preparation and chemical analysis, where finally assay information is obtained from a few grams of pulverised sample, and are used for further production, planning, operational and financial-marketing decisions. Different International Standards (depending on the commodity) are used to establish the methodology to be followed, to set-up and obtain samples from the Sample Stations, and the specifications are visually inspected to give an estimation on the performance of the sampling point. This paper seeks to highlight with examples, the importance of the implementation of a continuously monitored Quality Program (QAQC and QM) on Sample Stations, focused on the parameters that directly affect the quality and representativeness of the samples. By this implementation, a proactive approach and better-informed decisions can be taken for mining companies to: a) quantify/improve production and reconciliation results, and b) to supply the right specifications of shipped ore, increasing the value of the Resources. Finally, laboratory results are normally used as an indication of the quality of the information applied for the economic transaction, but it should be considered, clarified and highlighted that the laboratory will only process and analyse a sample obtained from a Sample Station, and potential problems on bias or precision may occur in stages prior to the laboratory reception. Hence the importance of the implementation of a quality assurance program that protects multi-million dollar decisions.

Mar 22, 2022

In this paper, the recovery of copper minerals and molybdenite in the rougher/scavenger banks of two separate mineral processing plants is compared with recovery in laboratory (batch) cells. A number of metallurgical surveys were conducted in two plants treating porphyry copper and molyb-denum ore. Batch flotation tests were performed on plant conditioned flotation feed slurry, in parallel with the plant metallurgical surveys. The effect of flotation feed density on recovery of copper minerals and molybdenite in the plant and batch laboratory cells was investigated. Changes in flotation pulp density had little effect on copper mineral recovery, in both plant and laboratory cells. The ultimate recovery for molybdenite, on the contrary, increased considerably when the pulp density was reduced, both at plant and laboratory scale. Recovery of copper minerals in the plant and laboratory cells was comparable, while molybdenite recovery in laboratory flotation cells was 3%~13% higher than in plant. It is hypothesised that the flotation rate of molybdenite is sensitive to cell hydrodynamic conditions (i.e. local turbulent energy dissipation) more than the flotation rate of copper. The flotation behaviour of molybdenite particles is likely to be predominantly controlled by bubble-particle collision frequency, which is enhanced in high local turbulent energy dissipation environment. For chalcopyrite, the flotation recovery is mostly determined by attachment and stability efficiencies. An increase in local turbulent energy dissipation, while increasing collision efficiency, may negatively impact on attachment and stability efficiencies. The outcomes may have a considerable impact on increasing molybdenite recovery from porphyry ores.

Jan 1, 2014

By Uwe König

Traditionally quality control of iron ore sinter, its raw materials and raw mixtures has relied on time-consuming wet chemistry. The mineralogical composition that defines the properties is often not monitored. XRD analysis in combination with Rietveld quantification and statistical data evaluation using Partial Least-Square Regression (PLSR) has been successfully established to determine the mineralogical composition and process parameters such as the FeO (Fe2+) content and basicity of iron sinter within an analysis time of less than 8 minutes per sample. Both methods take the full XRD pattern into account and can be simultaneously applied on the same measurement. In addition the Rietveld method was used to quantify the phase content of raw mixtures to monitor the composition of blending beds.

Aug 16, 2017

By Shillabeer J

Paste backfill has been adopted by many underground mines in North America and a growing number elsewhere. Paste offers a number of advantages. This paper suggests wider applications of paste technology to surface tailings disposal and water management. Advantages include improved overall stability, potentially easier permitting, smaller water inventory and earlier reclamation. It may be feasible to use the same plant to prepare backfill and to dispose of surplus tailings. Example cost models are given to illustrate potential applications.

Jan 1, 1998

By A. J. Keast

This circular is one of a series dealing with the exploration, equipping, and development of mining properties, prepared and published by the United States Bureau of Mines in cooperation with various mining and exploration companies in the United States and Canada. This series of papers will supplement an earlier one which covered the methods and costs of mining and milling at a large number of producing mines. The present paper describes the exploration, equipping, and developing of a group of 18 claims remote from rail transportation, and the transport of equipment and heavy supplies for a distance of 120 miles by tractor over ice and winter roads, and of men and lighter supplies by airplane.

Jan 1, 1933

By GEORGE T. Harley, Walter R. Storms

This paper, which describes mining mothods at International Minerals & Chemical Corp, 'e. potash mine. in. Eddy. County, N. Mex., is one of a sories being prepared by the Mining Branch of the Bureau of Minos. on mining method a and practicos in, various mining districts of the United States. The mine shafts and. surface plant or International Minerals & Chemical Corp. are situated. in. sec.. 12, T. 22 S., R. 29 E., N. M. P. M., about 26-1/2 miles by paved highway east of the city of Carlsbad (figs. 1, 2, and 3). A spur line of the Atchison, Topeka & Santa Fe Railroad connects the mine with the Clovia-Pecos branch of the same road near Loving, a few miles south of Carlsbad. This spur also serves the refinery of United Staics Potash Co. This report gives. the history and describes the geology of the district. Methods of prospecting, exploration, sampling, and estimation of tonnage and values are explained; development and mining methods are discussed in con- siderable detail; transportation, ventilation and drainage are outlined; safety measures are noted; and the wage scale and organization are mentioned.

Jun 1, 1949

By H. E. Lake

VERY EARLY in the initial stages of underground development work at Eldorado's Beaverlodge operation, the decision was made to use mill tailings as a backfill product. Mining and milling commenced in June, 1953, using locally available sand as backfill, while test work and installation of a plant was carried out to prepare ?and deliver the tailings to the mining areas. The first use of tailings was made in February, 1954, a sandslime separation being carried out with hydraulic cyclones. To date (January. 1956), approximately l 40,000 tons of fill have been used in the stoping areas, providing very effective support in a 50 deg. Vein system of cut-and-fill mining. The recoverable portion of the mill tailings amounts to 40 to 45 per cent, which has resulted in a product giving a percolation rate of 6 to 10 inches per hour. Owing to the fact that Eldorado has milled from 15 to 2 5 per cent more ore than it has mined, through the purchase of custom ore, the degree of control on the sand-slime separation has not been as critical as it might normally be when the filling operation must depend only on the tailings from ore mined. A description of the conditions involved and of the plant as finally installed is given below. It might be mentioned here that, with the impending increase in milling capacity from 700 tons to 2,000 tons p.er day, the present plant will be considerably altered within the ensuing year to handle the increased tonnage and distribution.

Jan 1, 1956

By F. L. Wideman

This paper lists resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizons, an area comprising approximately 522,600 square miles, Sources of sulfur occuring within the region are sulfur are, pyrite and pyritic ores, and natural gases and petroleum. Data concerning these sources are presented on a statewide basis. Some of the known deposits of sulfur ore are surficial and of fumerole origin; other deposits have resulted from oxidation of pyrite or sulfide ores of copper, lead, and zinc. The deposits are small and the sulfur is distributed erratically in them. There is a small production from some of the deposits, and the material produced is used as soil conditioner.

Jan 1, 1957

By Floyd R. Anderson

Noise control of existing pneumatic drills is difficult and runs into cost, performance and weight penalties. A need exists for a start-from-scratch approach for quiet pneumatic rock drills. The designs based on Leavell Principles which has been successfully used in demonstrating a quiet and vibration free paving breaker, is the concept chosen here. This report shows the feasibility of a quiet stoper for drilling roof bolt holes in coal mines. The work is directly applicable to pneumatic percussive rock drills. The report shows an oscillator based on patented Leavell concepts which results in a vibration free tool and noiseless exhaust. Dynamics of the oscilator is analyzed. Independant rotation of drill rod is provided by an air motor (screw expander) and flushing of cuttings is accomplished by an air ejector in a compact lower housing. The feasibility of no exhaust noise, low drill machine noise, and vibration free casing is discussed.

Jan 1, 1977

By Robert H. Richards

(Pittsburg Meeting, March, 1910.) THIS is in part a review paper, indicating the various steps that have been taken in developing hindered-settling apparatus, some of the standard data that have been obtained, and some of the conclusions one is led to as to the effect of it in improving concentrating-methods and machinery, and in part it brings in some unpublished work. CAUSES OF LOSS IN ORE-CONCENTRATION. In making a study of the separation of valuable minerals from the waste gangue, particularly by water concentrators, it is necessary to define, first of all, what are the causes of-loss that are likely to interfere with the concentration. Having made this definition; we can then study to see in what way the machines make their losses, and plan remedies for them in an intelligent way. Losses may be stated to occur as included grains, as flat or long grains, as fine free mineral, and as absolute slime. We will take, these up one by one, as follows: Included Grains.-Fig. 1 shows by a set of diagrams how included grains may occur: first, where the heavy mineral grains attached to the quartz are of large size; secondly, where they are of small size ; and thirdly, where very fine particles of heavy mineral are included in the quartz. We have to decide in regard to included grains whether they are rich enough to go direct to, the furnace, or poor enough to throw away, or whether they lie between these two points and require recrushing as the only means of severing the values from the waste. This last case is the only one requiring special treatment at our hands. We will therefore consider that next. * By mutual consent, this paper has been presented also before the Colorado Scientific Society, and the Canadian Mining Institute, Montreal.

Feb 1, 1911

By Edward P. Larsen

At our annual meeting in St, Louis, Mo. in February 1961, we presented a comprehensive paper (No. 61-B-22) on the subject of "Blending and Handling of Materials for Agglomeration". In that paper you will find a discussion on the difference between "blending" and "mixing". With regard to "blending" we brought out the facts of its usefulness for the preparation o materials in an agglomerated mass to attain controlled chemical and physical uniformity. "Mixing" was discredited as not being useful for the attainment of uniformity of any kind.

Jan 1, 1962