Search Documents

By F. P. Haver

A method to recover copper and elemental sulfur from chalcopyrite concen¬trate, using a ferric chloride leach, CuFeS2 + 3FeCl3 ? CuCl + 4FeCl2 + 2S, was reported by the Federal Bureau of Mines in 1971 (Report of Investigations 7474). Since that time, additional work has been done to improve certain steps in the procedure; that is, the recovery of sulfur from the leach residue, the recovery of copper and iron from the leach solution, and the regeneration of the leach solution. It was determined that over 99 pct of the elemental sulfur in the leach residue could be extracted at ambient temperature with an ammonium sulfide solution. Heating the pregnant solution precipitated crystals of rhombic sulfur (99.5 pct purity) and liberated ammonia and hydrogen sulfide for recycle. Copper with a purity in excess of 99 pct was obtained from the leach solution by electrolysis, using a diaphragm cell, with an energy requirement of less than 0.7 kW-hr/lb. Metal was deposited as a weakly adherent powder that could be easily dislodged from the cathode and withdrawn continuously from the cell in the form of a slurry. During electrolysis, part of the Fe(II) was oxidized to Fe (III) at the anode so there was no chlorine evolution. The leach solution was regenerated by direct oxidation of the spent electrolyte with air or oxygen in a turboaerator at 80° C. This precipitated the iron dissolved during leaching in an easily filterable form, Fe203.xH20, and converted the remaining Fe(II) to Fe(III).

Jan 1, 1975

By M. Maldonado, P. Olivares

"A submersible sensor for real-time gas holdup measurement in the collection zone of industrial flotation machines is introduced. The working principle is based on the generation and measurement of a pulp flow using a gas-exclusion cell immersed in the aerated slurry. The gas exclusion cell consists of a variable-area open vertical tube designed to be filled only with pulp by preventing gas bubbles entrance. The higher density of the fluid column within the cell generates a downward flow of pulp; the rate of this flow is proportional to the gas holdup outside the cell. The gas holdup measurement is achieved by tracking the velocity of the pulp flow leaving the gas-exclusion cell, using a magnetic flowmeter. Construction details of a prototype and its testing in two- and three-phases are discussed.INTRODUCTIONFlotation process optimization consists of finding and maintaining operating conditions that maximize flotation performance measured in terms of recovery and grade. The selective separation of mineral particles proceeds in two interactive zones where different and simultaneous phenomena take place: in the collection zone, the valuable particles are separated by collection on the surface of bubbles, while in the froth zone, the bubble-particle aggregates are gathered, drained to remove entrained particles, and taken into the concentrate stream. The cell overall performance, which can be determined from proper stream sampling, is a function of the recoveries in the individual zones. These zone recoveries cannot be independently measured nor calculated from operating variables. Progress in the assessment of these recoveries has been slow because on-line and reliable sensors to measure properties of the drastically different dispersions existing in both zones are not available.In the case of the collection zone, it has been demonstrated that the recovery of hydrophobic particles on the surface of bubbles, considered as a process with first-order kinetics, correlates with the bubble surface area flux (Finch et al., 2000; Hernandez, et al., 2003; Lopez-Saucedo et al., 2012). Bubble surface area flux (bubble area generated per unit time and cell cross-sectional area), is a variable affected by gas flow rate, bubble size distribution, and frother type and concentration. Gas holdup (volumetric fraction of gas dispersed in the slurry) is also affected by the same variables, and as such, carries information on the interacting variables that define the performance of the process. Therefore, a correlation between gas holdup and bubble surface area flux was expected and demonstrated (Finch et al, 2000), and since gas holdup is easier to measure as no bubble size is required, it has the potential to be the basis of a cell control and optimization strategy if a continuous sensor is available."

Jan 1, 2016

By Pratik Goel, Sumanta Haldar

High-speed rail is an emerging area of interest in India. The Government of India is implementing prestigious bullet train projects in various parts of the country. High-speed rail (HSR) will be operating in India at about 320 kmph at an elevated track on a viaduct for most of the ongoing and upcoming corridors. High-speed projects in India necessitate an indigenous solution for design applications for viaduct design. Pile groups are extensively used in viaducts for high-speed trains, as they can be a settlement reducer and increase the bearing capacity. Post-construction settlement of pile foundation for high-speed railway viaduct is a concern of engineers. Limited attention has been paid to estimating the post-construction settlement. This paper aims to propose a prediction of the cumulative settlement of pile groups due to cyclic train loading. A three-dimensional finite element model (3D-FEM) of the pile group is established in Abaqus CAE. A suitable plastic model is used to simulate the subsoil. The pile group is modelled as an isotropic-elastic element. The study examines the influence of cyclic loading time and train speed on the settlement of the pile group. The analysis is carried out considering various single pile and pile group parameters like S/D, Ep/Es, L/D, Pile cap thickness, etc. and finally, an optimum configuration is suggested.

Sep 1, 2022

By Cory Dippold, Michael Mett, Jérôme Steinkühler, Kristi Latimer

For decades, tunnels of all types have been a significant part of our infrastructure. In particular, water tunnels carry millions of gallons of fresh water every day to major metropolitan areas and surrounding communities. As a critical piece of public health infrastructure, it is important to inspect the condition of these tunnels regularly to ensure reliable and continuous operation. A specific challenge with water infrastructure is that it’s often difficult or impossible to shut down the system for long periods of time to perform the needed inspections. The latest method of tunnel condition assessment is the use of hybrid reality 3-D scan data. Photogrammetric and LiDAR based 3-D data ensure a reliable and objective view of tunnel conditions. The data can be used to support a detailed digital inspection including the compilation of databases that consist of a wide variety of deficiencies such as cracks and spalls within the structure. Mott MacDonald, a design engineer company worked closely with Dibit, used a 360-degree scanning system to collect high-resolution photogrammetric and LiDAR data on a recent project involving a water tunnel. The allows for full 360-degree coverage of the tunnel surface including a water covered invert. It operates at walking speed and ensures a fast and reliable data acquisition which can reduce the time of tunnel shutdowns. Several allocated inspection weeks can reduce to few days, with the final work product being a higher quality and more complete deliverable than traditional inspection methods would have provided. The true-color 3D-model has a photo resolution of 1 × 1 mm (0.039 × 0.039 inches) which makes cracks visible with a width of down to 0.3 mm (0.011 inches). The assessment of water tunnels, its technical challenges and the results of the 3D-tunnel inspection case study are illustrated and described in this publication.

Dec 1, 2022

By L. G. Bergh

The experience developing a supervisory control and information systems in a SX pilot plant is presented. The plant is located at the Process Control Laboratory, Santa Maria University, in Chile. In this work, the problem of controlling this process is discussed and related literature is briefly reviewed. Then, an innovative control scheme organized in three levels, local, hydrodynamic, and metallurgical supervisory controls is presented in an architecture including field controllers, PLC, and PC networks. Operating decisions in the metallurgical supervisory control are taken with incomplete information from on-stream analyzers. The control proposed is based on metal and acid concentration predictions of intermediate and exiting streams through the use of dynamic and static models and flow rates and input concentration measurements. Preliminary results are presented. The main objectives are to develop and test intelligent techniques in a hybrid system, and to study measurement and supervisory control problems. It is expected to produce reliable results that will contribute to improve the efficiency of this emerging and important process.

Jan 1, 2007

By M. England

Test equipment has been developed to record automatically both the displacement of the pile head and the load applied during a conventional maintained load pile test. Some systems also have, in addition, been fitted with the facility for maintaining the applied load, as set by the operator, at very constant levels. The advantages are both commercial and technical, but a well trained operator has to be in attendance to control the test. Since typical test specifications in the UK require more than 19 hours to complete, it became inevitable that at least one equipment operator remained on site to expedite the test for its duration. Although electronic measurement and data logging of load tests may be more safe than previous direct observation of dial gauges. A single person remaining on a construction site alone is not to be recommended, even if they are just supervising the test. Further development of the testing system produced equipment which will perform the entire test specification as required without operator intervention. To achieve this, full automation is employed. The patented method particularly addresses the safety requirements and by using additional sensors, detects any uncharacteristic behaviour of the pile under test or of the reaction system and the equipment takes appropriate action in a controlled and safe manner. The quality of test data returned from these automated systems is a key element when analysing pile behaviour with models such as CEMSOLVE? and TIMESETTM. These analysis methods often indicate ground disturbance resulting from installation technique and have allowed pile design to be optimised using actual field data rather than theoretical considerations alone. An additional feature is remote access, this allows the data recorded to be transferred and the progress of the test to be viewed from practically any location. This permits experts to view the data 'live' and allows rapid diagnosis of any problems with the expected pile behaviour.

Jan 1, 2002

Hazardous waste has often very complicated chemical compositions in a variety of physical forms and is normally processed in rotary kiln incinerators. Due to large variations in waste types and difficulties in feed characterization, the complex transport processes within the incinerator are not well understood, and the incineration process meets challenges in a smooth operation, and expects various uncertainties in the process chemistry and emission control. For better understanding of the incineration process, simulation was carried out by using Computational Fluid-dynamics (CFD) to characterize temperature and species distribution in the incinerator. In order to catch certain aspects of thermal and chemical behavior, a novel approach is proposed to represent approximately the waste streams and the subsequent combustion process. Hazardous waste in various forms from an industrial-rotary-kiln waste incinerator is firstly converted to a hydrocarbon-based virtual fuel mixture with approximately the same HIC molar ratio and calorific value. The simulation of the combustion process of the simplified hazardous waste was proceeded with a combustion model. The distribution of temperature and chemical species especially the remaining CO in the system is preliminarily investigated. Distribution of CO concentration, as a good indicator of emission level for the incineration process, could be used to evaluate the emission control. The predicted temperature distribution has been compared with available measurement data from an operating rotary kiln waste incinerator at AVR-Chieme, in the Netherlands. Reasonable agreement has been reached between the measured and predicted temperature data. In the next step, measurement of species distribution in the system is planned to further validate the combustion model.

Jan 1, 2003

By L A. Martinez Tipe, J McKibben, S Barry

"Metal prices are central to a mineral investment decision and have a profound impact on the financial performance of companies in the mining industry. At its most basic level, metal prices are influenced by the disequilibrium between international metal volume supply and demand. That is, the commodity price is a regulator that equates international metal supply and demand where inventories act as a buffer between the emergence of this disequilibrium and its dissolution through a price change.From this viewpoint, mining companies are required to forecast metal and bulk commodity prices when evaluating minerals projects through discounted cash flow (DCF) analysis. While supply-demand models are instructive, many companies use historical prices, spot prices, futures/forward pricing and consensus opinion (or a combination of all of these) to develop price forecasts.This paper discusses the definition, fundamentals and differences between futures/forward and consensus pricing and the appropriateness of each in a DCF model for mine project economic evaluation.Our results demonstrate that great care is required when using either futures/forward or consensus pricing and that the decision to use one rather than the other requires consideration of other important elements in the DCF model (ie the risk-adjusted discount rate).CITATION:Martinez Tipe, L A, McKibben, J and Barry, S, 2016. Metal prices and the differences between forward and consensus pricing – which one is better for use in a discounted cash flow model?, in Proceedings Project Evaluation 2016, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By T. McNulty

The author was privileged to find employment as a uranium mill chemist for The Anaconda Company while working his way through school in the mid-1950s. He then served Anaconda in various technical and management positions until 1980. This paper describes the prevalent technologies employed by uranium producers, briefly describes various mines and mills in the U. S., and memorializes a few of the thousands of men and women who contributed to the U. S. Uranium Boom. Following isolation of uranium as an element by M. H. Klaproth in 1789, uses of uranium were confined primarily to pigments, glass coloring agents, and ceramic glazes. In 1896, Antoine Becquerel found that uranium is radioactive, releasing particles and energy as it decays. In 1898, Pierre and Marie Curie isolated radium from uranium and learned that it can be an effective treatment for some types of cancer. In 1939, it was discovered that the isotope U235 is fissionable1 . Up to this point, nearly all uranium production was from pitchblende concentrates made in Bohemia, Canada, and the Belgian Congo. In 1938, only about 5 percent (23.85 short tons) of global output was produced from ores of the carnotite mineral that were being mined in the U.S. By the early-1950s, physicists in many countries had begun to recognize the potential for nuclear chain reactions. Ernest Rutherford (UK), Frederick Soddy (UK), and Leo Szilard (US) explained transmutation of elements and formulated the principle of “atom splitting”. In 1934, Marie Curie’s daughter, Irène, and her husband, Frédéric Joliot, identified uranium as the most viable source for this new form of energy. The basic fission process was unraveled by German scientists in December 1938. After Hitler’s army seized the uranium deposits in Czechoslovakia, many feared that Germany would build the first nuclear weapon.

Mar 2, 2022

When solid pillar is not left to separate different mining levels in underground mine with high dip angle deposit, waste rock in the backfilled stope could be a safety hazard to future mining activities on levels above or below the backfill. Different backfill methods can be used to eliminate this hazard according to the deposit shape and mining method. Building concrete pillar in ore drift of each mining level is one of them. Concrete pillar had been constructed in underground mines based on operational experience. Little design literature and pillar performance data can be found. At Great Basin Gold Hollister Mine, over two thousand feet of concrete pillar had been constructed. The project started with engineering design which combined civil engineering concrete design and the specialties of underground construction. Time Domain Reflectometry technique was installed to monitor the pillar movement and concrete cylinder samples were collected and tested for quality control. Engineering design, underground construction, quality control and concrete pillar monitoring, as well as precious concrete mixing data from years of experience are fully covered in this paper to give a general frame of concrete pillar method.

Jan 1, 2010

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By Frederick M. Becket

AFTER all the chronology that has been given, what is the present status of chromium steels? For the purpose of this discussion the different types of chromium steels can be divided into three classifications-those containing relatively low , percentages of chromium, say 5 per cent or less; the medium-chromium steels containing up to about 18 or 19 per cent chromium; and the steels containing still higher percentages of chromium, and some of the special alloys. Chromium has some unique effects in steel, so it is well to make a few generalizations. The affinity of chromium for carbon is great and the metal is unique in the manger in which it supplements and enhances the effects of carbon. Chromium retards -considerably the thermal transformations on cooling and exerts an opposing influence both on the absorption and precipitation of the carbides in steel. These statements make it easy to understand the fact that chromium .steels are capable of producing a hardened product at a much slower rate of cooling than is, true of plain carbon steel, and that chromium carbide or -the mixed carbides of iron and chromium do not contribute to brittleness to as great a degree as does iron carbide.

Jan 1, 1929

By B. K. Mishra, P. Patnaik, B. C. Tripathy, I. N. Bhattacharya

Cobalt is an essential metal considering its numerous industrial applications. The demand for the metal is increasing due to its wide range of use in, for example, rechargeable batteries and as an alloying element in super alloys. Cost effective production of Co is critical. Electrowinning from aqueous sulphate solutions is the preferred technology available for the production of Co. Attempts are being made to produce uniform, smooth and bright deposits of cobalt metal. Use of organic additives in the electrolytic bath improves current efficiency and deposit morphology of the metal. We investigated the effect of quaternary amines TEABr, TPABr and TBABr during cobalt electrowinning from aqueous sulphate solutions. Among the additives studied, TEABr yielded the best results. Smooth and bright deposits of cobalt were obtained at low concentration of TEABr (10 mg/L) maintaining a very high current efficiency of 99.6%. X-ray crystallography indicated that (100) is the most preferred plane of crystal growth.

Jan 1, 2014

By R. C. Kellner

Duval Sierrita Corporation, a wholly-owned subsidiary of Duval Corporation, operates an 86,000 STPD copper-molybdenum concentrator near Tucson, Arizona. Shortly after production commenced in February, 1970, it became apparent that the reduction crushing system represented a limitation to reaching the design capacity of 72,000 STPD. The development work performed on the reduction crushers in order to first meet design capacity, and to subsequently increase production to 86,000 STPD is described in this paper. The Sierrita plant is a conventional three stage crushing sys- tem. All crushers were supplied by the Allis-Chalmers Corporation and consist of two 58 x 89 Superior gyratories, four 138b EHD hydrocones, and ten 384 hydrocones. Screening is performed prior to and subsequent to secondary crushing and in closed circuit with the tertiary crushers. Typical throughput rates and equipment sizes are presented in Figure No. 1.

Jan 1, 1975

By M. E. Bilir

In this paper, we review cases in which dramatic and visual swelling problems are experienced in underground structures. Swelling rocks have caused many problems in underground engineering projects. They pose severe problems to the design, construction and maintenance of underground openings. If an appropriate integrated design procedure, which proceeds from exploration, tests, analyses and realistic assumptions of swelling behavior, is used during the design stage, the execution of the project can be completed without any serious delays or dramatic design changes. The case histories were subdivided into three classes that include tunnels, underground coal mines and others. For the evaluation of cases, the surrounding rocks, swelling minerals, water inflow, swelling test results and swelling problems were considered. The main purpose of this review is to inform the reader about potential problems with swelling phenomenon and to emphasize the rehabilitation and extensive cost which are encountered due to the lack of necessary integrated design approaches.

Aug 1, 2013

By S. A. Falconer

Much attention and publicity has been given, during recent years, to grinding, classification, flotation, and thickening. The various technical papers, and symposiums held to discuss these important phases of milling, have contributed to a better under- standing of the fundamental principles and operating variables involved. Another important part of milling- to the flotation operator-is a treatment step to which frequently too little attention is given-" conditioning," or the treatment the ground mineral pulp receives before it enters the flotation machines. Conditioning" is a hackneyed and frequently misused term, commonly employed to describe the pretreatment of surfaces of minerals in ore pulps or mill pr6ducts prior to froth flotation. In general, such pretreatment is for the purpose of changing the flotation characteristics of these mineral surfaces to enable them to respond in some desired predetermined manner when subjected to flotation. Taggartl states that the function of conditioning is "either to insure selective collector coating of one mineral species while another species is not; or to take such steps as will compensate for departure there from."

Jan 1, 1949

By S. C. Termes

The Bureau of Mines has used Fourier transform infrared spectroscopy (FT-1R) to study in situ reactions of aqueous solutions of potassium ethylxanthate with CU(II)-and Pb(II)-activated sphalerite plates, in which the plates were both the infrared-transparent windows and the reacting surfaces. A copper (I) ethylxanthate formed predominantly with Cu(II)-activated sphalerite, regardless of the activation time. The products formed on Pb(II)-activated sphalerite depended on the activation times; a short activation time (30 min) yielded a lead ethylxanthate-like product, but a long activation time (90 min) yielded a considerable amount of dixanthogen.

Jan 1, 1986

By C. O. Stee

Introduction The property of Siscoe Gold Mines, Limited, is located on an island of three hundred and forty acres in lake Kienawisik, about fifty-two miles east of Noranda and forty-three miles south of Amos, Quebec. Lake Kienawisik is a part of the Harricanaw drainage system and is crossed by the main line of the Canadian National railway at Amos. This waterway is navigable for boats with a draught of six to eight feet. Diesel engines have been the source of power at the property since milling operations were commenced in January, 1929. The power plant as first designed and built was for a milling capacity of 100 tons. Two Polar-Atlas units, each of 200 h. p., comprised the original installation. With the growth of the 'mine, more engines were added until, at the present time, there is installed at the Siscoe what is rated the largest Diesel plant at any mining property in Canada. Definition of a Diesel 'The Diesel engine is an internal combustion engine which works with liquid fuel introduced after, and independently of, the air charge at a time when communication between the cylinder and the outside atmosphere is cut off, and which ignites the fuel by compression-beat and stored combustion-heat unassisted by heat sources outside the cylinder itself while the engine is in stable operating condition"(1).

Jan 1, 1934

By T. Bartnitzki, N. Fietz

"INTRODUCTION For a long time now automation has been state of the art in production engineering and chemical engineering. The advantages of automation are, for instance, higher reliabilities of production processes, higher product qualities as well as capacities and improved safety conditions for the personnel. In contrast, many operations in mining are still conducted manually by machine operators instead of autonomous control units. One example for this is the excavation of underground hard coal which is still executed with aid of human perception. The Institute for Mining and Metallurgical Machinery (IMR) has been working on possibilities for sensor-based automation of mining machinery for many years now. Thereto the focus is set on the implementation of common material analysis techniques into ruggedized conditions as a basis for automation. Laser-induced breakdown spectroscopy (LIBS) for instance is an atom emission technique which enables the determination of the elemental composition of a sample. After introducing LIBS this paper will give an overview on dust formation during the cutting process. With the illustration of a few examples the challenges in determining dust concentrations specifically such of cutting processes are explained in further detail. The final chapter will outlay the possibilities and challenges in utilizing cutting-induced dust for the automation of shearer loaders. LASER-INDUCED BREAKDOWN SPECTROSCOPY LIBS Fundamentals LIBS (laser-induced breakdown spectroscopy) is a contact-free method for analyzing materials in any state of aggregate. It pertains the atom emission techniques and is based on the generation of plasma, inducing avalanche ionization on the surface of a solid material or any spot in a gas or aqueous solution. With sufficient background information on the expected elements and an additional calibration, this method can determine all present elements not only qualitatively but also quantitatively. However, this method cannot be utilized for determining the molecular composition of materials – if this feature is required a complementary method such as Raman analysis needs to be added. (1, 2)"

Jan 1, 2015

By S. H. Ash

Introduction Probably the newest thing in mining safety is the apparent dissatisfaction on the part of the mineral industry, as represented by both management and labour, and the general public of many nations in which mining is conducted, with the safety record of the mining industry. This is reflected by published comments in the technical press;' in labour periodicals, in popular Journals and periodicals, and in the daily press (5, 11). Despite what may be said to the contrary, mining in the United States is becoming safer, and this trend has been evident for several years (see Figures 1 to 4). Because the author's experience has been mostly in the United States this paper will discuss briefly some recent observations in the United States that have a bearing on mining safety. Because coal mining is of primary interest to the Mining Society of Nova Scotia, the paper treats mostly of coal-mining safety; however, many hazards in mining .are common to all mines, regardless of the minerals mined.

Jan 1, 1950