Search Documents

By S. Bastola, Y. P. Chugh

"This research determines shear strength and stiffness properties of bedding planes and joints in the roof strata rocks within 7.5 to 9 m (25-30 ft.) overlying the Illinois #6 coal seam (within the pressure arch zone). A shear test loading device was designed into a 1.334 kN (150 t) Forney Compression Loading Machine to perform direct shear tests in accordance with ASTM D5607-08 “Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens under Constant Normal Force”. The data were used to determine peak and residual friction angles and the dilation angle. A total of 49 bedding plane samples were tested, out of which 46 (36 intact and 10 relatively weak and loose) samples passed QA/QC procedures in accordance to ASTM D5607. Samples from eight (8) different bedding planes- shale/limestone (SL), shale/sandstone (SSs), shale/bone (SB), laminated sandstone (LS), shale/shale (SS), bone/bone (BB), bone/limestone (BL), and limestone/limestone (LL) were tested. The number of samples tested for each bedding plane were: SL- 11, SSs- 8, SB- 5, BB- 4, LS- 6, SS- 9, BL- 1, and LL- 2. Peak and residual shear strength values at 2.75 MPa normal stress range 1.06 – 6.26 MPa and 0.82 MPa to 0.82 – 4.14 MPa, respectively. The average normal and shear stiffness values are about 11.98 GPa/m and 3.11 GPa/m. Dilation angles are low (<10?) and negative in some cases. Angle of sliding friction values range from 9? to 42?. Joint Roughness Coefficient (JRC) values were less than 10.INTRODUCTIONRock mass may be defined as the total in situ rock medium containing bedding planes, faults, joints, folds and other structural features. Therefore, it is discontinuous and may have heterogeneous and anisotropic engineering properties. Upon creation of an excavation in a rock mass, bedding planes and joints are the most likely points of failure initiation. The failure typically occurs either in tensile or shear mode. Upon failure initiation stresses are transferred to the neighboring rock mass and the failure progresses until stability is achieved through equilibrium of stresses and strength. An example of this mechanism is development of the pressure arch. This study determined the shear strength and stiffness properties in shear and compression of bedding planes and joints in the immediate roof strata rocks within 7.5-9 m ( 25-30 ft.) overlying the Illinois No. 6 coal seam (within the pressure arch zone). Since such data are currently not available for Illinois Coal Basin mines, researchers and engineers have been using estimated values for design purposes. The immediate roof lithology in the proposed mining area consists of shale 0.62 m; Bone 0.09 m (0.3 ft.); Limestone, 0.10 m (0.33 ft.); Shale 2.37 m (7.9 ft.); and sandstone 0.55 m (1.83 ft.). The bedding plane samples were provided by a mine in south-eastern Illinois operating at a depth of about 180 m (600 ft.)."

Jan 1, 2015

By E. Arghavani, S. H. Amiri, S. Zare, F. Sepehri, M. Ramezanizadeh

Mineral processing plants include different stages like crushing, grinding, classification and concentration, all of which have partially affect the final product. To identify and solve the related problems of each stage, process audition should be carried out continuously to find the major solutions of improving product and decreasing the maintenance and operating costs. The Iranian Gohar-Zamin iron ore beneficiation plant consists of equipment such as gyratory and cone crushers, high pressure grinding rolls (HPGR), ball mill, dry and wet double-deck vibrating screens, hydrocyclones cluster, magnetic drum separators, thickener and horizontal vacuum belt filters. The defects of initial design as well as current non-standard operating conditions of equipment were monitored and detected and the opportunities for process optimisation were presented as follows: establishing the control loop of power draw for cone crushers, the modification of feeding chute in cone crushers to minimise the non-uniform wear of parts, removing segregation in the fresh feed bin and screen’s circulating load chute in order to provide the proper feed to HPGR, reducing wear rate on HPGR rolls surfaces, decreasing the amount of rejected materials in screen, equalising the solid content and particle size distribution (PSD) of feed in all magnetic drum separators and equalising the PSD of hydrocyclones overflow. This paper provides a guideline for the mineral processing industry to focus its efforts on process design to deliver the efficiency with minimum capital costs. Keywords: Process audition, gyratory crusher, cone crusher, HPGR, screening, hydrocyclones, magnetic drum separators

Jan 1, 2020

By Mark S. Sanders

The present study was designed to explore the contribution of organizational climate and management practices to the injury experience in underground coal mines. A cross-lagged panel design was used in which miners from 22 mines completed questionnaires assessing 27 organizational climate, structure, and function dimensions on two occasions, The results strongly support the hypothesis that climate and management practice have casual effect on the incidence of disabling injuries.

Jan 1, 1976

By Alexander Ciccone, John H. Gill

Jet grouting is a highly versatile ground modification technique that can offer significant commercial and technical advantages over traditional concrete pit underpinning applications. Despite these advantages, jet grouting remains an underutilized technique in the construction industry due to its perceived complexity, cost, and risk. When performed thoughtfully, underpinning by jet grouting offers significant safety and schedule advantages over traditional underpinning approaches. The New England construction market has seen a recent acceptance in the use of jet grout underpinning on congested project sites across a variety of subsurface conditions. The reduction of the cement batch plant footprint due to equipment advances has allowed the use of this technique in urban sites where its use would be previously infeasible. Furthermore, jet grout underpinning has been utilized for support of historic and sensitive structures with generally lower tolerance to settlement than is typically feasible with conventional pit underpinning. Robust, real-time geotechnical instrumentation monitoring systems have helped reduce the uncertainty and further expand the feasibility of jet grout underpinning applications. When properly designed and constructed by qualified and experienced jet grouting contractors, the flexibility of soilcrete for design and construction may be utilized to overcome the many inherent challenges which complicate underpinning and earth retention systems. INTRODUCTION The construction of buildings and infrastructure in our increasingly dense urban spaces often requires excavations below the elevation of existing structures immediately adjacent to the proposed work. Where a proposed excavation system encroaches into an existing structure’s zone of influence, additional measures, such as the construction of an underpinning or excavation support system, are required to safely excavate and minimize the impacts on the adjacent structures. Jet grouting is one method of underpinning that offers significant commercial and technical advantages over many other techniques. Though it was first used to the United States in the 1980s and has grown in popularity elsewhere, jet grout underpinning remains underutilized domestically due to its perceived cost and risk premium. Jet grouting has significant technical advantages over other underpinning methods due to its applicability in a wide range of soil types and its flexibility of design and installation. The jet grouting process is capable of limiting the movement of foundations during construction and excavation to lower thresholds than most traditional underpinning methods (Droof, Furth, & Scarborough, 1995). Its use for underpinning historic and sensitive structures with lower settlement criteria provides additional evidence to its technical utility. Through thoughtful design, adequate planning, and experienced installation, jet grouting can be an appropriate underpinning solution that can provide significant cost and schedule savings.

Jan 1, 2019

By Mowat D. M., Louis H., Smith W. Mackey W. M., Dron R. W., Ellison C. C., Winmill T. F., Kerr G. L., Haldane J. S., Ashworth J., Garforth W., O'Shea L. T.

Discussion of Winmill's paper, including various anecdotal examples, is presented together with the author's response; topics included: the need to distinguish cubic pyrites from the rapidly decomposing rhombic form known as marcasite; the effects of moisture content in the coal and air; the possible effect of pressure; the heat insulation resulting from heap/stack size; and the means of determining pyrite and moisture contents

Dec 1, 1916

By David K. Ingram

Research performed by the U.S. insurance industry has determined that mine subsidence is uninsurable. Consequently, the insurance industry has decided not to voluntarily offer mine subsidence insurance. The U.S. Department of the Interior has long been investigating the effects of mine subsidence. These investigations have resulted in Federal regulations and controls of mine subsidence. This U.S. Bureau of Mines report generally describes mine subsidence, the development of mine subsidence insurance programs, and the eight current mine subsidence insurance programs in the United States. The States that have these subsidence programs include Colorado, Illinois, Indiana, Kentucky, Ohio, Pennsylvania, West Virginia, and Wyoming. Major aspects of the programs include history, administrative and operational procedures, insurable structures, recognition of mine subsidence, major exclusions, claims, insurance premiums, and the economic health of each program. Addresses of agencies involved with mine subsidence insurance are also given. Information within this report can be useful for residential and commercial property owners and mine operators. States that are considering starting or have an existing mine subsidence insurance program can also use this report as a model for initiating or modifying their programs.

Jan 1, 1993

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jason Navoyski, Jennica L. Bellanca

The paper describes the process of collecting detailed accounts of near-miss incidents and turning them into impactful visual stories using graphic simulation. The aim is to create high-quality training materials to reduce haul-truck-related accidents and fatalities in mining.

Sep 1, 2023

By Carl R. Christiansen

Underground sites have great potential for industrial plants, for warehouses, and for other purposes where above-surface locations are now employed. Subsurface locations have generally been over- looked by industrial planners even though they may offer many features of superiority over the conventional sites. There are many opportunities for industries or warehouses to go underground. New space can be excavated expressly for this purpose or openings in existing mines may be converted to useful space. Another possibility is the pre-planned mine-industrial site, in which a mineral product is mined and marketed as a commercial venture while utilizing a mining plan which will permit rapid conversion of the openings created into active industrial areas while mining continues in the adjacent ground. An underground plant located in chambers created by excavating space in solid rock has many advantages, including low construction costs, low heating-cooling costs, freedom from storm damage or other surface weather conditions, absence of traffic noise and vibration, fireproof construction, low insurance costs, excellent working conditions, easily controlled temperature and humidity, almost unlimited bearing capacity of floors, low maintenance costs, no effect upon surface.

Jan 1, 1973

By L. Gonzalez-Sardi, W. McCombe, M. Pearson

Pressure oxidation is increasingly being used for processing refractory sulphide ores and concentrates because it offers highly effective base metal and precious metal extraction while minimizing elemental sulphur, arsenic & mercury emissions. Yet pressure oxidation processes introduce new safety concerns and process risks as demonstrated by a number of safety incidents over the last 20 years, including overfilling, oxygen-metal fires, nozzle/sparger failures, and uncontrolled pressure relief events. Chemical Process Safety regulations in the United States and Canada mandate that companies constructing or operating chemical process facilities perform a rigorous hazard and risk analysis based on either ANSI/ISA-84.00.01 or IEC 61511 safety standards to determine the level of protection required for each hazard in the plant. This paper describes the application and implementation of three (3) unique safety instrumented systems developed by Hatch for ensuring the safe operation of three different pressure oxidation processes.

Jan 1, 2014

By A. Bakalarz, M. Duchnowska

"The copper sulfide ore from the Legnica-Glogow Copper Basin in Poland, which is processed by KGHM Polska Miedz S.A., consists of three lithological fractions: dolomitic, sandstone and shale. The copper ore, depending on the mining area, contains all fractions in different ratios. The lithological fractions differ in the particle-size distributions of their useful minerals. In the dolomitic part of the ore, most of the metal sulfide particles are 50-200 microns in size, while those in the sandstone and carbonaceous shale are 30-200 and 5-40 microns in size, respectively. This complex composition results in different mineralization, physicochemical properties and, in particular, upgrading selectivity. Due to the specific nature of the examined copper ore, two of the crucial parameters determining the beneficiation efficiency are size and liberation of sulfide particles. We analyzed the influence of grain size of feed on scavenging selectivity in one of the KGHM flotation plants and performed evaluation and analysis of the upgrading results of industrial beneficiation of the ore, containing mostly dolomite and shale. The upgrading efficiency was estimated using a selectivity indicator obtained by means of the Fuerstenau upgrading curve, which was then correlated with the particle-size distribution of the flotation feed.IntroductionFroth flotation is used extensively in commercial ore treatment flotation plants to separate minerals from gangue and to separate minerals from each other. The floatability of ores and their benefication selectivity are determined by many factors. One of them is particle size. The effect of particle size on flotation performance has been widely studied by many authors (Gaudin et al., 1931; Trahar, 1976; Trahar and Warren, 1976; Lynch et al., 1981; Pease et al., 2004). Particle size also plays a critical role in the probability of particle collision and attachment to bubbles (Solari and Gochin, 1992; Schulze, 1993), kinetic flotation (Taggart, 1956; Ahmed and Jameson, 1985; Debacher, 2002; Brozek and Mlynarczykowska, 2007; Potulska 2008), collector consumption (Sutherland and Wark, 1955; Vianna et al., 2003) and mechanical entrainment (Lynch et al., 1981; George et al., 2004; Konopacka, 2005). Most of the results have shown that there is an optimum particle size range for a given flotation system and that the simultaneous optimization of the recovery and concentrate grade of these particles in conventional flotation equipment is extremely difficult."

Jan 1, 2015

By George H. Anderson

A CHAPTER of appealing interest was added to the industrial history of the Southwest early in June, when the War Production Board gave final approval to the erection of a blast furnace, a battery of coke ovens, an ore-beneficiation plant, and other facilities for the production of pig iron in northeastern Texas, just north of the East Texas oil field. For many years the people of Texas and adjoining states have cherished the ambition and desire that eventually an iron and steel industry drawing upon local mineral resources would be established to serve Southwestern markets. The existence in this vicinity of valuable deposits of iron ore, limestone, and coking coal has been known in a general way for many years, and efforts have been made from time to time to use them in the production of iron. The present development promises to bring to realization the dreams of the men who have visualized what the establishment of this basic industry would mean to the region.

Jan 1, 1942

By Klaus-Markus Peters, Robert M. Cravens, James G. Hemrick

"Degradation of refractories in molten aluminum applications leads to energy inefficiencies, both in terms of increased energy consumption during use as well as due to frequent and premature production shutdowns. Therefore, the ability to enhance and extend the performance of refractory systems will improve the energy efficiency through out the service life. TCON_ ceramic composite materials are being produced via a collaboration between Fireline TCON, Inc. and Rex Materials Group. These materials were found to be extremely resistant to erosion and corrosion by molten aluminum alloys during an evaluation funded by the U.S. Department of Energy and it was concluded that they positively impact the performance of refractory systems. These findings were subsequently verified by field tests. Data will be presented on how TCON shapes are used to significantly improve the thermal management of molten aluminum contact applications and extend the performance of such refractory systems.IntroductionThe production of molten aluminum creates aggressive environments for processing equipment, thereby requiring refractory materials to contain the aluminum during melting, transfer, treatment, and casting operations. Degradation of these refractories not only causes issues with reduced product quality and production yields, but also increases heat losses as the insulative properties of the refractories are compromised. Furthermore, in addition to disrupting production output, refractory failures lead to further impacts upon energy efficiency as large amounts of energy are lost during the cooling and subsequent reheating of the equipment as the refractory linings are repaired or replaced.The need for improved refractory materials is recognized throughout the industry. A joint U.S. Department of Energy and industrial workshop held in 2000 on applications for advanced ceramics in aluminum production [1] noted that refractory materials used in melt processing equipment have many limitations. The workshop report noted that these issues may be addressed by using advanced ceramics, but new materials must be cost effective when compared to current refractory materials. Also, in 2005 the Canadian aluminum industry produced a technology roadmap [2] having the goal of identifying and bridging gaps between current technological resources in the industry and future requirements. One of the areas identified as being crucial to the future of the industry was the need for improved molten aluminum-resistant materials."

Jan 1, 2009

By Merle L. Bowser

The Bureau of Mines has constructed a miniature oxygen deficiency alarm system using an electrochemical cell as the sensor. Distinct audible signals are produced at either of two preselectable oxygen levels which can be varied from approximately 10 to 20.9 percent oxygen. The high or cautionary range produces a 500-cycle-per-second tone pulsed at about a 1-cycle-per-second rate, whereas the lower or more dangerous oxygen level produces a continuous 500-cycle-per-second tone.

Jan 1, 1968

By G. W. Weems

The Bureau of Mines used the Burnett method and apparatus to determine the compressibility factors for helium and carbon dioxide mixtures at 0°, 10°, 20°, 23°, and 35° C and to pressures of 900 psia. Tables of compressibility factors and approximations of the virial coefficients are presented for seven binary mixtures as well as for helium and carbon dioxide. The results compare favorably with existing data.

Jan 1, 1969

By B. J. Scheiner

The presence of organic materials in gold ores cyanidation. The presence of organic materials interferes with gold extraction by The carbon contained in the ore has been shown to adsorb gold cyanide complex from solution. Removal of the carbon content by roasting or chemical oxidation prior to cyanidation results in gold extractions of 85 to 95 pct. This paper by the Bureau of Mines, U.S. Department of the Interior, discusses how the mineralogy of the carbonaceous gold ores affects gold recovery by cyanidation. It also discusses the advantages and disadvantages of roasting and chemical treatment to render the ore amenable to cyanidation.

Jan 1, 1987

By J. B. Mitchell

Using digital image correlation the evolution of strain and strain at the onset of localisation resulting in a hot tear has been determined for alloys AA6111 and Al¬0.5wt% Cu during solidification. High resolution images of hot tear formation and growth were captured during a constrained bar test that incorporated a glass window above a central hot spot region. The images were analysed using digital image correlation software to measure the evolution of displacement and strain based on tracking the motion of discrete features on the as-cast surface of the sample. Temperature data was also acquired with a thermocouple cast into the sample in close proximity to the hot tear. The interval starting from the point immediately after solidification shrinkage ends (the metal pulls away from the glass) and finishing when the first sign of a crack or hot tear is visible to the eye was used to determine strain data. The minimum strain at which strain localisation occurs was found to be 0.0069 in AA6111 and 0.0021 for A1-0.5%Cu.

Jan 1, 2007

By Pragna N. H. Bhakta

The minerals industry is under political and economic pressure to reduce its processing wastes and minimize their impact on the environment: Recycling is one of the means by which the minerals Industry can reduce the quantities of effluents and residues that are discharged to the environment. The wise use of available resources is not only an environmental necessity but also an economic benefit as natural mineral resources are depleted and/or become more complex. The purpose of this paper is to review the technical and regulatory issues that will help shape the future of minerals recycling over the next ten years. Research and development to address technical issues will be discussed with emphasis on the Bureau of Mines recycling research program.

Jan 1, 1992

By J. L. SILSBEE

THE existence of large saline deposits in that flat arid basin, known as the Great Salt Lake Desert, has long been recognized, but the extent and great commercial value of these deposits has not been generally appreciated. That a very considerable interest has recently developed is indicated by the fact that about 263 prospecting permits-each covering about 2560 acres of land in this Desert-have been issued under the Potash Leasing Act (Act of 0ct. 2, 1917-40 Stat. 297), and patents granted on approximately 40,000 acres. It is reported that patents and leases have, or will be applied for on an additional 80,000 acres in the basin. , Tests have been made on probably less than 10 per cent. of the total area of the basin, but these have proved a practically unlimited supply of brine available -sufficient, probably, to. furnish the potassium and magnesium chloride requirements of this country for at least a hundred years.

Jan 1, 1925

By Sashnee Raja, Mehdi Nemati, Ashley Sissing, Susan T. L. Harrison

"Extreme thermophiles, operating at 65 - 90°C, are finding increasing application in biohydrometallurgy. These micro-organisms have the advantage of exhibiting better oxidation kinetics in terms of reaction rate and extent of mineral solubilisation (Duarte et al., 1993; Norris and Barr, 1988; Konishi et al., 1995). These extreme thermophilic Archae, characterised by a different cell envelope structure (König and Stetter 1986, König 1988, Michel et al. 1980) perceived to provide reduced structural strength in comparison to bacterial envelopes, and customised metabolic pathwaysThe active tank bioleaching process, used for high rate leaching, is conducted in a slurry bioreactor. Here sufficient energy dissipation is required to ensure suspension of the mineral phase as well as to sustain high rates of gas liquid mass transfer. It is well known that subjection to hydrodynamic stress of sufficient magnitude may alter the physiological state of a range of micro-organisms through changed viability (ability of the microbes to grow), metabolic activity and integrity. While limited study on the influence of the solids phase on thermophilic leaching performance is reported, initial reports suggest that the thermophiles used for bio-oxidation appear to be sensitive to hydrodynamic conditions (Jordan et al 1993, Clark and Norris, 1996) and the presence of solids (Norris and Bar 1988, Le Roux and Wakerley, 1988, Escobar et al. 1993, Torres et al. 1995, Nemati and Harrison, 2000)."

Jan 1, 2003

By J. Craig Green

Companies mining for coal, oil shale, and minerals in the western US must often complete extensive geotechnical studies to satisfy federal and state regulations. The modern mining process is further complicated by the legal problems and liabilities associated with mineral rights and land leasing. Yet the study of water rights-unique to the West is often incomplete or ignored until the latter stages of mine planning. Water rights in the West are not adequately understood by many mining companies and their geotechnical consultants. Some firms, headquartered outside the western US, have not had to contend with the water supply problems of a semi-arid region. Water problems encountered by eastern mining companies, for example, are primarily water quality, drainage, and flood control. Even when water quantity is a problem in these areas, ownership and/or use of it is governed by entirely different legal and administrative concepts than in the West. Both legal and engineering issues have to be considered when studying western water rights. Legal issues, such as existence and title, must be addressed to insure that a particular water right is properly established and maintained. The exercise of a water right, however, often requires engineering analyses that focus on preventing injury to the properly established water rights of others.

Jan 8, 1981