Search Documents

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and, (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke. This is the third of a series of reports giving results of studies by counties under part (1) of the investigation. This report covers Pike County, Ky., which comprises parts of the Harold, Williamson, Matewan, Gilbert, Pikeville, Regina, Hurley, Pound, and Clintwood quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By David A. Greenhut

The Kubota surface melting system has been under development since 1975. It has found commercial application on the melting of municipal sludge, and ash from solid waste. The melted product has physical properties allowing its use as a substitute for aggregate in cement and asphaltic construction. This paper describes the surface melting system, its current use and anticipated future use.

Jan 1, 1991

By J. S. Kennedy, M. M. Fine

"INTRODUCTION Barite is one of the major industrial minerals whose production has increased considerably in the last 10 years. In 1935 domestic production of barite was 218,075 tons and. had increased by 1944 to 515,136 tons. 3/ Most of the primary uses for barite and barite products were developed before 1935, so the increase in barite production reflects the growth of industry in general rather than any recent developments in barite technology.The principal uses for ground and crushed barrite are as a weighting agent in heavy drilling fluids, as a filler in rubber and other materials, as a pigment and extender in paints, and as a flux in glass melt. In addition, a considerable' quantity of barite serves as the raw material for the manufacture of lithopone and barium chemicals.Specifications for barrite vary widely and depend primarily on the use to which the material is put. The primary requisites for barite used in heavy drilling muds -are that it have a minimum specific gravity of 4.2 and be very,low in soluble salts. A minimun barium sulfate content of 92 percent may be specified; but this is less important than the gravity. 4/ In addition before consumption the material must be ground to '92 percent minus 325-mesh. 5/ Lithopone and chemical manufacturers require a minimum of 94 Percent barium sulfate, a maximum of 1.0 percent iron oxide, and not more than a trace of fluorine. 6/ Barite used as fillers in light-colored products should be of fairly high grade, but the filler used in dark products may be considerably lower grade.Glass barite should contain a minimum of 96 percent barium sulfate, not more than 3 percent moisture, a maxium of 0.2 to 0.4 percent iron oxide, and not more than a trace of titanium oxide. Particle size is a matter of some importance in glass barite, also. 7/"

May 1, 1948

By John G. Holmes

The generation of low cost power is but one phase of the TVA program for regional development. During the 36 years since TVA began, growth in its generation of electric power has necessitated a shift from a predominantly hydroelectric power system to a combination steam and hydroelectric system. The addition of steam-electric power plants to TVA's generating system was necessitated by the rapid increase in the traditional and defense demands for electric power in the 80,000-square-mile area served by TVA, the need to firm up the hydroelectric power, and the fact that all available sites for sizeable hydroelectric projects had been developed. At present TVA owns and operates 40 power plants--29 hydroelectric and 11 steam-electric plants. The total generating capacity of the hydroelectric plants is 3,105,430 kw, and the capacity of the steam plants is 13,951,135 kw. This provides a total generating capacity of 17,056,565 kw for the plants operated by TVA. Individual capacity of the 112 hydroelectric units ranges from 10,000 to 67,500 kw, and the individual capacity of the steam-electric units now in operation ranges from 60,000 to 950,000 kw. In addition to this generating capacity, TVA distributes the power from 6 U. S. Army Corps of Engineers hydroelectric plants on the Cumberland River. These plants contribute an additional 725,000 kw. Also, under an agreement with the Aluminum Company of America, TVA directs the stream flows and generation of their 423,715-kw system on Tennessee River tributaries and shares with Alcoa in the increased generation resulting from this coordinated operation.

Jan 1, 1969

By Brian J. Olson, Kevin Haiar

Originally constructed between 1939 and 1941 as part of Franklin D. Roosevelt’s New Deal programs, the Bonneville to Hood River 115 kV Transmission Line required an infrastructure upgrade to remain reliable and in-service. The line traverses the rugged landscape of the Columbia River Gorge on the Oregon- Washington border, featuring steep, talus slopes; uneven, rocky terrain; and a variety of environmental sensitivities. This paper details the design and construction of 27 micropile foundations for new, fire- hardening steel poles through a particularly challenging stretch of the alignment. The difficult access and environmental constraints at these sites designated them as helicopter-accessible and precluded the collection of detailed geotechnical information prior to construction. Micropiles provided a viable foundation alternative due to their portability and flexibility during construction. Detail will be provided on the extensive preliminary desktop study performed, as well as the process of developing engineering designs to successfully accommodate for variability and unknowns in complex geological conditions. With an increasing number of electric power projects traversing challenging terrain and facing similar obstacles, this project stands to provide valuable lessons learned to the industry.

Sep 8, 2021

By M. Fall

The progressive depletion of ore available at shallow depths in several underground mines around the world means that underground mining operations would increasingly be carried out at greater depths and therefore at higher temperatures. However, our understanding of the effect of hot temperatures on the response (mechanical, economical, environmental) of cemented paste backfill (CPB) is still limited. Hence, an extensive laboratory investigation was conducted to study the performance of young and aged CPB, in response to deep mine temperatures. Several CPB samples with different compositions, cured at different temperatures (20 to 50°C) and different times (7 to 160 days) were tested regarding their mechanical properties, economical performance (binder consumption) and microstructural properties. The results show that hot temperatures significantly affect the performance properties of CPB at young and advanced ages. An increase in the curing temperature leads to a considerable improvement of the rate of gain of CPB strength and also to a significant increase of the strength of CPBs studied. CBP samples cured at hot temperatures show lower binder consumption and finer pore structure. Results of this study could serve as background information for the development of optimal mine backfill design procedures.

May 1, 2007

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Temple Mountain mining district is unique among the uranium-producing areas on the plateau. This relatively isolated mining district is in Emery County, Utah, on the eastern flank of the San Rafael Swell, about 35 miles southwest of the town of Green River. The district lies just within the eastern escarpment of the San Rafel Reef - a rampart of rugged and tilted sandstone cliffs that encircles the highly eroded core known as the Sinbad Country. The presence of petroleum matter found associated with the ore deposits, the occurrence of uranium in various formations, and the structural deformation caused by collapsed features have aroused a great deal of geologic interest. Mine development on Calyx Flat is distinctive, in that the ore deposits are worked through 36-inch calyx-drill holes.

Jan 1, 1957

"INTRODUCTION Secondary mine ventilation has been hamstrung by the availability of fans that satisfy many competing operational factors. The sometimes legislated requirement of adequate volume to the working face, the minimisation of excavation required to fit the selected secondary fan and the power requirements of various operational phases has, in the past, not been satisfied with just one system. The new system being introduced overcomes all these competing requirements in one simple unit with an added bonus of being very durable without loss of performance when wear occurs on the impeller. Existing Operational Situation Several studies (e.g., CIPEC, 2005; LCG Energy Management Group, 2009) have found that between 42% and 49% of mining energy costs are associated with mine ventilation, depending on the type of mine and the equipment used. If we then look at the general breakdown of installed power of the secondary fan to primary vent fans, the ratio is around 2:1. Thus the total energy costs of the secondary ventilation represents about 25% of the overall mining energy costs. It is of interest to note that the cost of running a typical two stage axial vs the cost of purchasing and general maintenance cost of the same fan over a 10 year period, the breakdown will be conservatively in the order of 40:1.The currently available secondary ventilation axial fan have one duty curve at any given time. Generally this can be changed manually within the motor power parameters but requires a minor outage and removal of the fan to do the pitch adjustments. As the bag vent ducts grow longer, the supplied air reduces to a point where inadequate air is supplied to the working face. This is exacerbated by underground equipment putting additional resistance in the heading and further reducing the supplied air at the working face. This shortfall is normally corrected by the installation of an additional fan in the system to overcome losses in the bag system but comes at a cost of production as the heading needs to be shutdown to install the second fan. This also means that the heading is supplied with excessive air on the shorter runs with a wastage of fan power."

Jan 1, 2019

By E. V. Manlapig

"Some researchers postulate that the floatability of a particle in the streams of an industrial flotation circuit is a function of only its size and liberation properties. They do not discount the importance of reagent or surface contamination on particle floatability but assume that the reagent coverage or surface contamination of the particle surfaces is essentially uniform for particles of similar size and mineralogical properties when subjected to a particular chemical regime.In this paper, samples collected from batch tests performed on different streams of the Red Dog lead cleaning circuit have been characterised with respect to their size, mineral association and mineral surface exposure. An analysis of this data set indicates that particle recovery rate is significantly affected by mineralogical properties - in particular the degree of valuable mineral surface exposure.However, through the use of a nodal analysis technique developed by the authors, it can be concluded that particles with the same size and mineral composition do not all float with the same rate, but with a distribution of rates. The characteristics of this floatability distribution do not change during the flotation process. It is suspected that the particles within a size mineralogical class in this study have varying degrees of surface oxidation and that this results in varying particle flotation rates. Thus basing particle floatability on size and mineralogical effects, alone, in a flotation model is not always valid."

Jan 1, 2003

By W. R. Lindsay

Anyox, where the Hidden Creek mine of the Granby Consolidated Mining, Smelting and Power Company is located, is situated on an excellent deep-water harbour in Granby bay, at the head of Observatory inlet, about 600 miles from Vancouver and 90 miles north of Prince Rupert. Anyox is the Indian name for the little stream which empties into Granby bay, and means 'hidden creek'. The Ore-Bodies The ore is a replacement deposit and occurs at and near the contact between argillites and a later intrusive greenstone. This contact locally has a general north-and-south trend, an irregular westerly dip, and in the vicinity of the ore-bodies there has been intense folding, accompanied by faulting. The mineralizing solutions supposedly were derived from the Coast Range granite batholith, distant one to two miles to the east and north. The whole area is cut by many dykes of varying widths, which seem to have had but little part in the ore deposition.

Jan 1, 1929

By Kenneth E. Hay

Researchers from the U.S. Bureau of Mines conducted a field study to assess the safety of remotely controlled mobile roof supports (MRS) in a retreat pillar mining operation, Data were collected to provide the Mine Health and Safety Administration with criteria needed to develop guidelines for MRS use and to determine if precursors could be identified that would alert miners to imminent roof falls. Two test sites at which two different support methods-MRS's and posts were used and were monitored to obtain information on entry stability. Pressure transducers and string pots were installed on all four MRS's to obtain loading and displacement information. and roof bolt load cells. sonic probes, extensometers, and survey targets were installed in the surrounding entries to obtain information on ground behavior. Results showed a larger increase in roof bolt loading and roof movement when MRS's were used, especially in the intersection area. Roof bolt loads in the entries showed decreases in load when the MRS's were set and increases up to 11,1 kN (2,500 lbf) when the MRS's were unloaded. Unloading of one MRS in a pair did not significantly increase load on the other. MRS's I and 2 usually had the higher loads, with these loads increasing as the pillars on each side were being mined. MRS 3 normally had lower loads than I and 2: however, it also experienced some very high loads when in the last position near the pushout. MRS 4 usually had the lowest loads, primarily because it was located near the solid pillar that was not being mined.

Jan 1, 1995

By J Jones

A common problem in the mining industry is that company exploration groups operate in relative isolation to the rest of the company; resulting in poor knowledge transfer (Qureshi and Briggs, 2006) and often priority conflicts with mine geology, operations and project departments. In recognition of this problem, Newcrest created a Minerals Division responsible for stewardship and governance of mineral assets across the value chain from reconnaissance to rehabilitation. It was recognised at an early stage that effective collaboration both internally and externally would be required to improve decision making, deliver faster cycle times and improve governance.Collaboration in companies is generally associated with the introduction of new IT functions. However, modern IT-based collaboration systems and practices are relatively simplistic compared to the long-standing practices associated with collaboration and knowledge management in science and engineering disciplines such as geology and mining.The authors of this paper have started a trial of a 12-point plan for effective collaboration, which recognises that significant efficiencies can be gained and barriers to future success removed if more effective collaboration can be achieved between science and engineering divisions in a company along with external professionals and with the collective intelligence (Tapscott and Williams, 2006) of the outside world. To meet growth aspirations some companies, like Newcrest Mining Ltd, are adopting this comprehensive, step change approach by moving from a closed model the isolates mine geologists to an open and collaborative model that uses IT visualisation systems strategically. The paper describes how an open model provides people with the right work environment and the right information at the right time, which will help individuals and workgroups to work more collaboratively day-to-day. The aim is to achieve speed, focus and mitigate risk through an environment where everyone and anyone can contribute effectively (Cisco, 2008).

Aug 22, 2011

By J. L. Bowlby

Introduction In the following discussion, boiler-feed and mine waters will be considered from the point of view of the problems arising from the chemical nature of the mineral and gaseous impurities they contain. The theories underlying some of these problems will be reviewed for the purpose of getting a clearer concept of the problems themselves. Certain terms of a chemical nature, necessary to the discussion, will be explained on the assumption that they are not generally familiar to mining engineers. Finally, an attempt will be made to correlate theory and practice, with the abject of establishing certain limits to factors relevant to the problems, and to show that these limits are justified by practical experience. The general problems occasioned by the presence of mineral and gaseous impurities in boiler-feed and mine waters are: (1) Scale formation and corrosion in boiler systems. (2) Corrosion of mine pumps and pump fittings. These will be discussed separately. Boiler Scale Typical analyses of waters available for use in steam power-plants are given in the accompanying Table (Table I). All analytical data are expressed in grains per Imperial gallon. The bicarbonates of calcium and magnesium in the raw waters are shown as normal carbonates in the Table. Substances in the first five rows constitute the encrusting solids. All the waters listed in Table I would be classified as 'very good' in the schedule of classification for boiler waters adopted by the American Association of Railway Chemists in 1887. In spite of this classification, however, the waters contain sufficient encrusting solids to cause serious scale trouble after prolonged evaporation.

Jan 1, 1934

By Thomas M. Ware

"MR. Chairman, our Honourable Minister, Mayor Cole, it is a pleasure for me to come here, and join with you in one of the largest industrial shows ever held in Saskatchewan.It is an honour to be asked to keynote your meeting, to help mark an early chapter of this new industry for Saskatchewan. God has placed in our hands a new resource for His man on earth. This store of potash, 350 million years in the making, offers a vital resource to help man support his advanced intellect for thousands of years. It is a gift so large we must all wonder at its purpose and our responsibilities in serving our fellow man with it.We who are here to plan and implement the development of this essential mineral resource enjoy a great -privilege; and we share a great responsibility -to see that the billions of tons of potash which have waited beneath these prairies for millions of years are widely and wisely used to nourish the earth through future millenniums.To know the true value of potash, to be able to bring forth this re-source from over 3,000 feet deep in the earth, to establish markets and develop its potential worldwide is all part of our great heritage from generations past. So I think it is fitting on this occasion that we reflect for a moment on this heritage, to help us assess the responsibilities of its future development."

Jan 1, 1966

By David Yankovich, Geoff Hughes, David Haug, Jon Kaneshiro

"In March 2013, the Sanitation Districts of Los Angeles County began final design of the Joint Water Pollution Control Plant (JWPCP) Effluent Outfall Tunnel project. The new, approximately 7-mile, 18-ft internal diameter tunnel will provide additional capacity and redundancy for the existing 8- and 12-foot diameter tunnels, which were built in 1937 and 1958, respectively. Connections to an existing, active 14-foot arch force main and four existing ocean outfalls ranging from 5- to 10-foot diameter are required. This paper will present geological features for the project, and details of the proposed post-tensioned tunnel liner and associated structures. INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) are 23 independent special districts serving approximately 5.3 million residents in Los Angeles County. Seventeen of the districts that furnish sewerage services to the metropolitan Los Angeles area are signatory to a Joint Outfall Agreement that provides for a regional, interconnected system of facilities known as the Joint Outfall System (JOS). The JOS service area is shown in Figure 1. The JOS serves an area that encompasses 73 cities as well as unincorporated territory and parts of the City of Los Angeles. The JOS provides wastewater collection, treatment, reuse, and disposal for residential, commercial, and industrial users, and it includes seven treatment plants, the largest of which is the JWPCP, located in the City of Carson. Currently, secondary treated effluent is conveyed through two 6-mile long parallel tunnels, 8- and 12-feet in diameter, from the JWPCP to a manifold structure located at Royal Palms Beach, near White Point on the Palos Verdes (PV) Peninsula, from which four seafloor outfalls extend offshore. The two main outfalls, 90- and 120-inches in diameter, extend approximately 1.5 miles offshore and discharge at a depth of approximately 200 feet below sea level. The other two outfalls, 60- and 72-inches in diameter, are used for additional capacity during heavy rain events and extend a shorter distance offshore and discharge at shallower depths. A schematic of the existing system with the proposed tunnel and structures is shown in Figure 2, and the proposed 18-ft diameter tunnel alignment is shown in Figure 3. Both existing tunnels and main outfalls are required to be in service at all times."

Jan 1, 2016

By C. R. Nisewanger, F. W. Brown

"The velocity of detonation of an explosive is one of its most important properties, because its performance depends markedly on the rate at which it releases its energy. Fortunately, the velocity of detonation is one of the few properties of an explosive that can be measured precisely. However, the velocity of detonation of an explosive may depend on several factors other than its chemical composition, such as density, physical state, degree of confinement, nature of confinement, and magnitude of initiating impulse. Presumably for an explosive of fixed chemical and physical properties there are certain limiting conditions of confinement and initiation under which the explosive will detonate at a maximum constant and uniform velocity. This velocity is its ""ideal"" velocity of detonation. It is obvious, however, that in order to evaluate performance properties of an explosive in all of its applications it may be necessary to measure its velocity of detonation under a number of conditions in which the velocity of detonation is far from the maximum ""ideal"" velocity.. Under certain-conditions the velocity of detonation may even,be,different at different points in the explosive.It is .relatively simple to determine the velocity of detonation of an explosive under a. standard set of conditions if one is free to use large quantities of the explosive and to form it into a convenient shape. Under these circumstances; one can use a thin column of explosive a meter or more in length. The time required for an explosion to travel the length of the column will not be less,of the order a few ten-thousandths of a second and can be readily and accurately measured .by means of the standard spark chronograph or by photographing the explosion with a rotating-drum camera. However in many applications the explosive charge may be of relatively small dimensions arid may not be in a form convenient for making velocity measurements and often may be enclosed in a case or other confining medium. It may be necessary to determine the velocity of detonation over distances of the order of a few centimeters, in which case the time intervals to be measured will be extremely small. For example, the time required for an explosion to traverse 1 centimeter of tetryl is of the order of 1.5 microseconds.Since no satisfactory method of determining time intervals of the order of magnitude of a few microseconds within an explosive charge was available,, at least not for all conditions that might be encountered in practice, it was necessary to develop a special electronic chronoscope which is capable of measuring time intervals as small as a microsecond with a fair degree of accuracy. This report describes the chronoscope and its application to measurements of velocities of detonation in explosives."

Mar 1, 1946

By Oliver Bowles

A NORTH CAROLINA miner dreamed that he found high-grade mica by excavating a certain corner of his mine. The next day he sank a hole on the exact spot and found mica of excellent quality. The dream came true. May not this be as good a method as any yet known for forecasting the valuable mineral content of pegmatites? The Federal Geological Survey has found in its recent detailed studies in New England that good sheet mica occurs most abundantly in zoned pegmatites, particularly in zones lying along the wall or contact of the pegmatite mass. Although this conclusion may be a valuable guide, pegmatite mining operations must still be classed as most uncertain and hazardous enterprises. Finding of the second largest diamond ever discovered in the United States-a stone of good gem quality weighing more than 34 carats-during the course of a horseshoe pitching contest at Peterstown, W. Va., is another example of unorthodox mining methods. These should not be considered, however, as characteristic mining methods developed in 1944.

Jan 1, 1945

By C. A. Young, J. D. Miller

Adsorption isotherms previously determined by in-situ Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS) for oleate adsorption at calcite and fluorite surfaces near pH 9 and at various temperatures are compared. Results indicate that, at both mineral surfaces, chemisorption occurs at equilibrium concentrations below approximately l x l0-5 M oleate while calcium dioleate surface precipitation occurs at higher equilibrium oleate concentrations. The extent of chemisorption at the calcite surface is 3 to 5 times less than that at the fluorite surface while the extent of calcium dioleate surface precipitation on calcite is nearly a magnitude larger than that on fluorite. However, for both minerals, surface precipitation decreases with increasing chemisorption. Contact angle measurements and flotation recoveries show the hydrophobicity of fluorite to be greater than that of calcite at each of the temperatures and oleate concentrations studied. Significant differences are noted only in the chemisorption region. Unlike calcite, the hydrophobicity of fluorite was sensitive to the presence of oxygen in the system. Multichannel Laser Raman Spectroscopy (MLRS) showed this behavior was caused by the double-bond reactivity of adjacent chemisorbed oleate molecules and subsequent formation of an epoxide/polyether complex at the fluorite surface. Such a reaction product could not be detected at the calcite surface. These differences in adsorption density, hydrophobicity, and polymerization behavior are discussed in terms of the intrinsic surface properties of the minerals.

Jan 1, 1999

By T. M. Gurr

The United States is the world's leading producer of phosphate rock. In 1975 according to the US Bureau of Mines' statistics, 44.3 million tonnes (48.8 million st) of phosphate rock were produced in the United States, 1 which is 40.6% of the world's production.2 The major phosphate producing areas of the United States are located in Fig. 1 and the production for 1975 is listed as follows:

Jan 6, 1979

By Jeff Hopple

"Bluestone Dam in Hinton, W.Va., along the New River, is owned and operated by the U.S. Army Corps of Engineers (USACE). Completed in 1949, the dam is 165 ft (50 m) tall, 2,048 ft (624 m) wide, and encompasses a water shed that is 4,600 sq mi (11,914 sq km). The Bluestone Dam Safety Assurance (DSA) Program began in 2001, and is a multiple-phase construction project to upgrade the capacity and stability of the structure to meet the probable maximum flood event. Installing 216 high capacity rock anchors was a major feature of the work.The USACE selected Brayman Construction Corporation to perform Phase 2B of the construction modifications to the Bluestone Dam. Brayman was responsible for installing the high capacity rock anchors, which range in size from 3 to 61 strands and have a design load up to 2,145 kips (9,541 kN). Drill holes range in size from 6.5 to 15 in (16.5 to 38 cm), and required full length corrosion protection. Of the 216 anchors, 57 were installed on top of the dam to resist overturning and the remaining 159 were installed on the face of the dam at a 45-degree angle to resist sliding.To gain access to the face of the dam anchor locations, the project required dirt benches, excavations with temporary shoring, and steel platforms. To access anchors on the east and west abutment faces, the team excavated over 10,000 cu yds (7,645 cu m) of material. Support of these excavations included the design and installation of three soil nail walls with over 145 nails and 3,500 sq ft (325 sq m) of shotcrete. The project also called for a 780 ft (237 m) long steel platform to gain access to the spillway anchors. The Stratus Group designed the platform to support two 85 ton (80 tonne) crawler cranes and as many as five drill rigs that were the equivalent to a design load of 3.5 ton per sq ft (335 kN per sq m). Once the final platform design was approved, fabrication of roughly 3 million lbs (1,360 tonnes) of structural steel began. Brayman’s in-house fabrication shop, in conjunction with Dura-Bond Industries and Advantage Steel, collaborated to fabricate and install the platform in less than five months. Flexibility in the platform design allowed for sections of the platform to be lowered as much as 16 ft (4.9 m) to provide access to anchors at lower elevations along the spillway face. In addition to the main spillway platform, Stratus Group, Brayman, Dura-Bond and Advantage designed, fabricated and installed six other unique platforms to facilitate anchor construction on various areas of the dam."

Jan 1, 2014