Search Documents

By C. Zografidis, K. Karalis, E. Devlin, S. Tabouris

"The main parameters affecting energy and electrode consumption in smelting reduction of Greek nickeliferous laterites in submerged arc electric furnaces (E/F) were investigated. Within this framework, the operational data of E/Fs, such as energy consumption indicators, electrode consumption indicators and chemical characteristics of Fe-Ni and slag, were correlated with the physicochemical characteristics of the calcine, produced by roasting reduction of laterite in rotary kilns (R/Ks), such as reduction degree, temperature, chemical composition and granulometry. The results obtained provide a significant input for further research on the modelling of the roasting reduction – smelting reduction process, which is a critical tool for energy optimization.IntroductionThe two main steps of pyrometallurgical treatment of greek nickeliferous laterites for ferronickel production include: i) drying, pre-heating and controlled pre–reduction of laterite ores with solid fuel reducing agents and fuel oil in rotary kilns (R/Ks) for the production of a calcine, and ii) smelting reduction of the calcine in open-bath submerged-arc electric furnaces (E/Fs) for the production of Fe-Ni alloy with 12-16% Ni [1].The energy absorbed from the endothermic reductive reactions of iron, nickel and cobalt oxides (Fe2O3, FeO, NiO and CoO) of the calcine with the remaining carbon in the E/Fs, corresponds to about 16% of the total energy output in the smelting reduction step [1]. This is indicative of the significance of the calcine’s reduction degree for the electric energy requirements in the E/Fs. Moreover, the chemical characteristics and the granulometry of the calcine constitute critical parameters for the energy requirements as well as the smooth operation of the E/Fs."

Jan 1, 2012

By Wilbert J. Huff

For the past 9 years , the technical studies conducted by the Explosives Division of this Bureau have been summarized in a series of reports issued annually . The following account presents investigations undertaken from July 1 , 1943 , to June 30 , 1944. The work is detailed under a number of main headings corresponding to the organizational structure of the Division , the various activities being under the immediate direction of unit chiefs , who report directly to the author . Specific credit , however , is due to the individual unit leader and his assistants .

Jan 1, 1945

By Xianguo C, Baoqi S, Shaozhong Z, Huiling Z, Zhengbing C

Acidless and fluoless flotation is a new method for separating feldspar from quartz at the natural pH value of tap water in the absence of any acid and fluoride and other inorganic reagents. The paper introduces the production application of this method in plants and research results on the mechanism involved in the flotation method.

Jan 1, 1993

By R. R. Cellan

There have not been many opportunities to date for comparison between laboratory and commercial neutralization rinse data. Homestake Mining Company's Santa Fe project is one such comparison. This paper discusses laboratory procedures and results from a 100' leach pad height simulation column neutralization rinse test and compares principal data with that achieved in actual commercial leach pad neutralization rinsing procedures. Principal comparisons include the rate of WAD cyanide neutralization, decrease in effluent pH, stabilization of dissolved silver and copper, and the quantity of dissolved gold recovered during rinsing.

Jan 1, 1996

By Mark Jolly, Nasim Soleimanian

"During the last 20 years CFD (Computational Fluid Dynamics) has been used as a tool to aid furnace designers and manufacturers to improve energy efficiency and effectiveness of glass furnaces. However as the models are maturing the effect of feeding equipment used to push the raw material into the furnace has not been included in the process models. This paper investigates the effects of batch pattern in the melt space caused by charging equipment on the energy efficiency of the furnace focusing on the melting zone. A simple batch patterns sensitivity study has been performed using purpose built software (Glass Furnace Model-GFM). It is concluded that in order to further reduce the energy consumption of the furnace it is necessary to model the batch charging process in more detail to find more opportunities for improvement.Introduction Glass manufacturing is a conservative industry which applies to all the four major segments (float glass, container glass, fiberglass, and specialty glasses). Risks due to the high capital investment, very long service life of the furnaces, and the demand for high performance and quality from the outset translates into evolutionary progress rather than revolutionary. The main problem facing glass manufacturers are the financial cost of manufacture, its impact on the environment, and mounting pressure imposed by the authorities for greener manufacturing and reduction in emissions.The main energy intensive activities involved in continuous glass manufacturing are: the need for high temperature to create and maintain the viscous flow, homogenisation of glass melt (melt residence time), and maintaining the two to achieve continuous output of glass at the right quality. The high temperature and long duration of homogenisation has resulted in the design oflarge furnaces, which have high energy consumption, low specific performance, and high C02 emissions. As an example in the container glass sector the most efficient furnace has a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch. Even very small improvements in efficiency by optimising operation would have a high impact [1-14]. Given the conservative nature of the industry and the costs involved in experimental data gathering, CFD modeling of the process has been used extensively during last two decades to not only improve our understanding of the process but also as a tool in predicting possible optimisation windows, e.g. Glass Furnace Model ( GFM), a commercially available piece of software that has been developed to optimise furnace operation."

Jan 1, 2013

By Gamal Rashed

Coal bump is a sudden manifestation of the release of strain energy stored in a coal pillar (Peng, 2008). It is a very serious mining hazard that adversely affects the safety and productivity of the mines. Several case histories in mining have described coal pillars or faces of coal failing violently with an accompanying ejection of debris and broken material into the working areas of the mine (Campoli, 1987; Osterwald, 1962; Peperakis, 1958; Garvey and Ozbay, 2013). These failures resulted in large losses of life and total collapses of entire mine panels (Chase, Zipf, and Mark, 1994; Zingano, Koppe, and Costa, 2004). There are questions in the literature about whether or not the coal itself plays a significant role in bump. Rice (1935) mentioned that structurally strong coal is one of the key factors for bump; however, the strength of the Pocahontas #3 coal seam is low, and it bumped. Moreover, it is not obvious in the literature whether the strength of the tested coal samples is the inherent strength or if it is influenced by the shape or the size of the specimen. The main objective of this paper is to answer the following question: To what extent does the mechanical properties of the coal have an impact on the potential for violent failure? The best approach to answer this question is to compare the mechanical properties of two kinds of coals from bump-prone (Utah coal-Sunnyside seam) and non-bump-prone (WV coal-Sewickley seam). This comparison includes uniaxial compressive strength, modulus of elasticity, shear strength (cohesion and friction angle), and the burst index.

Jan 1, 2014

By Bror Nyrnan

Solvent extraction technology and equipment have been developed within Outokumpu since the early seventies. During this period altogether nine solvent extraction processes for molybdenium, zinc, rhenium, cobalt, nickel, calcium and magnesium have been commercially adopted in Outokumpu's metallurgical plants. During last years a new mixer-settler concept based on a "Vertical Smooth Flow" (VSF) principle has been developed. It has also been found to be a good method for copper solvent extraction, decreasing essentially the crud formation and the organic and aqueous entrainments.

Jan 1, 1994

By P J. Harris, C T. OÆConnor

Collectors are used to impart hydrophobicity on particles thus increasing their chances of reporting to the froth phase. Also, the extent to which naturally hydrophobic gangue particles, such as talcaceous minerals, report to the froth can be reduced by the use of depressants. Thus the use of collectors and depressants will directly influence the extent to which hydrophobic particles report to the froth. However these hydrophobic particles will also have a direct effect on the characteristics of the froth phase, more strongly hydrophobic particles causing a reduction in the stability of the froth with the expected concomitant effects on grade and recovery. This study included microflotation (ie frothless flotation) and batch flotation of various ores using a number of different collectors and depressants and a newly developed froth imaging device (SmartfrothTM). Flotation performance was characterised by mass and water recovery, and recoveries and grades of the valuables. This paper shows how the various reagents influenced the behaviour of the pulp and froth phases. The critical importance of managing the type and dosage of reagents used in flotation with a view to optimising their influence on the froth phase is discussed.

Jan 1, 2005

By C. B. Manula

This report is volume 9 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,' and ventilation. This volume of the final report describes the Water Generator subsystem of the Master Design Simulator. This subsystem simulates the flow of water through a typical watershed-reservoir combination to predict mine drainage quantities in underground workings. The model is a integrated one which handles both the unsaturated and the saturated flow domains as a unified system. The solution of the model is achieved by numerical tech¬niques of finite difference method coupled with finite elements analysis. The Water Generator can be operated either as a free standing model or in connection with the Geology and Reserves subsystem as a part of the Master Design Simulator. A case study is included illustrating the application of the model to actual data. The appendices of the report constitute a user's manual for the program, and include a program listing.

Jan 1, 1975

By E. J. Lintner

CLAY mining in the 'United States is by no means a small industry for approximately ten million tons of shale and clay are recovered yearly. The bulk of this tonnage enters into the manufacture of paving, building and refractory brick, draintile, pots, sewer pipe, stoneware, and wall and floor tile. This group of manufactures is commonly known as the heavy clay products industry. The winning of the raw materials for this industry constitutes merely a step in the manufacturing process because the manufacturer usually owns and operates his own source of supply. The mining of kaolin and the whiteware and chinaware claps, however, is usually a separate industry.

Jan 1, 1936

By Max Friedemann, Franziska Günther, Helmut Mischo

Ensuring adequate ventilation is a critical aspect of safety in underground mining operations. In small-scale mines in particular, key ventilation parameters such as temperature, humidity, and air velocity are often measured manually and only at infrequent intervals, typically using analog instruments. As a result, real-time monitoring of environmental changes, timely detection of hazardous situations, and demand-driven ventilation control are not feasible. This presentation discusses the selection and evaluation of modern digital ventilation measurement devices, including handheld instruments with digital data logging capabilities and continuously operating sensors with potential for real-time data transmission. The investigations focus on the challenges posed by underground environments with extremely high humidity levels, which can adversely affect sensor performance and electronic components. The results are based on testing conducted at the Research and Teaching Mine of TU Bergakademie Freiberg—an underground ore mine characterized by humidity levels exceeding 95%. Findings include assessments of measurement accuracy, reliability, and practical applicability under these demanding conditions.

Feb 22, 2026

By Carlos A. Jaramillo, Seng Hing Ngu

"The Murum Hydroelectric Project is a 944-MW development consisting of a 145 meter high RCC dam, two 2660 meter long, 9 meter excavated diameter upper pressure tunnels, surge shafts, two 950 meter long 7 even meter OD penstock tunnels and a surface powerhouse. The project is located in the eastern section of the State of Sarawak, Malaysia, about 200 kilometer from Bintulu, in the Rajang Fold-Thrust Belt, an Upper Cretaceous to Upper Eocene fold and thrust belt that extends under most of Sarawak. The Belaga Formation consists of a thick sequence of deep marine sediments currently appearing as steeply dipping strata of thin to thick bedded, fine to medium grained sandstone interbedded with argillaceous rocks, resulting on a “Flysch” type geologic environment. The project pressure tunnels were excavated perpendicularly to these strata resulting on frequent change on rock conditions and behavior, and required rock support. This paper describes the characterization of the rock mass, design of rock support, and incidents during construction. Particularly interesting were convergence issues in Tunnel 1 resulting from Tunnel 2 excavation. INTRODUCTION The Murum Hydroelectric Project is located in the eastern section of the State of Sarawak, Malaysia, about 200 kilometers from Bintulu, and upstream of the Bakun Hydroelectric Project. The project consists of a 145 meter high RCC dam, a 50 meter high intake tower, two nine meter OD and 2660 meter long upper pressure tunnels, two nine meter OD and 175 meter long vertical shafts, two 25 meter diameter and 80 meter deep surge tanks, two seven meter OD and 950 meter long penstock tunnels and four seven meter OD and 50 meter long branch tunnels, two 8 meter diameter to 3.4 meter diameter and 1400 meter long penstocks installed within the shafts, penstock tunnels and branch tunnels ending in a powerhouse with 944 MW installed capacity. LAYOUT OF THE WATERWAY TUNNELS The two waterways tunnels are basically parallel as shown in Figure 1, with each tunnel supplying water to two units in the powerhouse. The tunnels start separated 25 meters center to center, but 250 meter from the intake the separation increases to 35 meters. The tunnels are lined with reinforced concrete until they reach the surge shafts and steel lined from there to the powerhouse. The tunnel profile is shown in Figure 2."

Jan 1, 2016

By R. L., Fullman

During the past year there have been a number of significant investigations that have furnished evidence on the driving forces governing grain growth and on the role played by boundary impurities. Thus Burke has shown that in high purity alpha brass the rate of grain growth in the earliest stages is approximately inversely proportional to the existing grain size. This relation agrees with one derived by Zener assuming that surface energy was the driving force in grain growth. Also in confirmation of the surface energy hypothesis, Burke found that growth virtually stopped when the grain boundaries or even only the grain corners were melted.

Jan 1, 1949

By Greg J. Hasenfus, Allison M. Haines, Joshua M. Silvis

The floodable volume of longwall gob can be of great importance in developing accurate coal mine operation plans, particularly for mine water management and environmental control strategies. Given the inaccessibility and difficulty in direct measurement of gob characteristics following gob recompression, hydrologic, geomechanical, and spatial data and principles were used to solve for the porosity and height of the residual gob using a mathematical model framework and bulking-based techniques. Based on this approach, gob porosity of Appalachian longwalls appears to be tighter than previously reported, ranging between 4.99 and 14.31%. Residual gob height, as normalized with respect to mine extraction height, ranges between 1.90 and 2.45. A novel, bedding-based bulking approach is ampliative with respect to existing roof caving and bulking fundamentals, as it has greater explanatory value compared with the traditional, lithologic-based bulking application. The efficacy of using the residual gob characteristics determined by the mathematical model and bedding-based bulking is examined using a causal comparative method, whereby time series prediction of historical groundwater rebound is compared with observed mine pool elevation data. Prediction accuracy is significantly improved using a prototype model to calculate void volume of longwall gob, specifically, the dependence of porosity of the gob material upon the longwall width to overburden depth ratio for movement basins of subcritical and critical panel widths. The potential implication of these findings toward hydrologic, geomechanical, and ventilation studies of longwall gob could be significant.

Aug 13, 2021

By G. E. Maryniak

To date, human space exploration has been almost completely dependent on the use of resources carried with astronauts and cosmonauts from the surface of the Earth. The only exception to this has been the harvesting of solar energy to power space stations like Skylab, Salyut and Mir for long-duration missions. This dependence on materials which must be transported into orbit at costs in excess of $5000 per pound is the fundamental limiting factor in space exploration and operations. It is likely that launch costs can eventually be greatly reduced by means of such innovations as true single stage to orbit vehicles, aerospace planes, or serial electromagnetic or laser launch systems. However, the Earth will always remain an expensive source of materials for space construction and for basic commodities such as propellant and life support liquids and gasses. Fortunately, abundant sources of materials exist which are already in space, outside of the Earth's deep gravity well.

Jan 1, 1992

By Harold M. Wrigth

El siguiente estudio refiere al diseño y costo de construcción de las plantas concentradoras, así como el de plantas de beneficio realizadas en la provincia de British, Columbia. Para ello, el autor, quien diseñó aproximadamente 16 plantas para el tratamiento de minerales en el mencionado lugar, propone la dfusión y aplicación de este tipo de máquinas en nuestro país, considerando los tonelajes, las ubicaciones, resistencia del terreno, el flow sheet, para sentar las bases del diseño de los equipos.

Jun 20, 1954

By D. S. Salonine

Aluminum alloys are widely used in modern industry. Tubes and hollow shapes give great opportunities for structural purposes as well as fluid transport due to their stiffness and lightness, Extrusions on a mandrel or through a bridge die, that requires splitting of the billet with re-welding, produce hollow shapes with varied contours, fins and multiple cavities. Moving and stationary mandrels, mandrel lubrication, tooling for ribbed-tube heat exchangers, and for drilling pipes are considered. Bridge dies can be classified by the bridge position relative to the die face, by mandrel support structure, and by assembly type, The main parameters influencing the quality of the die-welded seams are considered, The difficulties of extruding various alloys through bridge dies are discussed in terms of metallurgical factors, Some approaches to the calculation of the stresses in a bridge are presented.

Jan 1, 2005

By M. Ye. Scheglov, G. I. Voiloshnikov, S. M. Ryakhovsky, V. E. Dementyev, V. N. Alekseev, N. S. Voiloshnikova

Irgiredmet has substantial experience on RIP and RIL technology for gold recovery, having started development of ion exchange technology in 1964. Irgiredmet specialists were involved in the majority of RIL and RIP projects in the former Soviet Union and Russia, and took part in commissioning of practically all plants using ion exchange technology. Laboratory and pilot plant tests were conducted to develop process design criteria for designing 15 RIP plants of the former USSR using bifunctional macroporous anionite AM-2B or its analogs. This paper is devoted to the laboratory, pilot plant testing and introduction of RIP technology conducted in cooperation with GC Pertopavlovsk. Medium base resin PuroLite S992 (PuroGold) was used as adsorbent. Some adsorption regularities and the affinity of resin to metal cyanide complexes were studied. Laboratory batch and continuous pilot tests on resin-in-pulp process were held for oxidised ores from Pioneer, Albyn and Malomyr mines (Amur region, Russia) owned by the Petropavlovsk company. A simplified flowsheet for gold elution and resin regeneration was developed. Alkaline cyanide solution was used as gold eluent and gold was recovered from eluates by electrowinning. Process design criteria were developed on the basis of the testwork results, and the plants were designed and constructed by GC Petropavlovsk. The RIP plant at Pioneer was commissioned in May 2008, at Malomyr in August 2010, and at Albyn deposit in December 2011. These plants are currently in operation at design performance at throughputs from 3 to 6.5 Mt/year. The primary gold ores of Pioneer and Malomyr deposits are refractory to cyanidation; Irgiredmet also completed continuous testwork on RIP technology using medium-base resin for pressure oxidation (POX) residues derived from their flotation concentrates. In 2019 a hydrometallurgical plant for the treatment of refractory gold concentrate after POX was commissioned at Pokrovsky mine (Amur region). Keywords: Gold ores, cyanidation, RIP, RIL –processes, ion exchange resin, medium base resin, adsorption, elution, electrowinning

Jan 1, 2020

Mechanical and electrical (M&E) systems in road tunnels are constrained by the traffic envelope and the construction profile. Whilst these spatial constraints are often ælocked inÆ early in the design process, the detailed M&E design continues for some considerable time after key civil engineering issues have been resolved. Ventilation design criteria for both normal and emergency operation often involves considerable negotiation with a wide range of stakeholders. Final system performance and spatial requirements are only finally resolved when suppliers are selected following the tender process. Lighting design is dependent upon a wide range of factors including tunnel lining materials and associated colours as well as agreed maintenance regimes. Cabling systems can only be developed when the general arrangement for power distribution is agreed and a system of substation, switchrooms and equipment rooms is in place. Many other systems such as fire protection and communications facilities fill the available space beyond the traffic envelope, where physical, structural and æsight lineÆ requirements must all be accommodated. The more co-ordinated civil engineering and M&E design is and the earlier the process starts the better the outcomes for all parties.

Jan 1, 1999

By H Parra, D Zenteno

Fragmentation modelling has been in use in the mining industry for a long time; however, there are still some aspects to tackle with regard to its use for strategic/planning and day-to-day purposes.On one hand, an important amount of resources are allocated to the task of calibrating and validating a good fragmentation model. Nonetheless, errors during the implementation stage introduce uncertainty into the prediction.On the other hand, it is common practice in the mining industry to use only discrete values to represent the fragmentation from blasting (k20, k50, k80), which provides a biased interpretation of the situation as, for instance, the best and worst possible cases are not taken into account. This is particularly critical when a continuous improvement philosophy has been adopted and modelling is used to either modify the drilling and blasting designs or plan ahead.It is well known that every site has particular conditions (rock mass, equipment, drilling and loading practices, among others) that often define unique trends in implementation. These trends can be captured using statistic and probabilistic techniques and then used as proxies for further analysis.This paper explores the potential of including implementation data in the form of probabilistic distributions into the Swebrec model to improve the performance of this engineering tool during the decision-making process.The fragmentation results of four designs were modelled using three different degrees of accuracy in the implementation for the burden, spacing and explosive column length.The data analysis showed that the probabilistic approach helps to achieve a broader perspective regarding the fragmentation that it is possible to obtain and the implications for the subsequent processes. The analysis also showed that the likelihood of producing similar fragmentation with different designs (involving different powder factors and costs associated) increases with the variability of the implementation.CITATION:Parra, H and Zenteno, D, 2015. Evaluating the inclusion of the implementation variability into fragmentation modelling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015