Search Documents

By D. R. Kreuzer

The sulfide smelting industry is striving for up-scaling their operations by increasing the throughput and efficiencies of the furnaces. The physical phenomena related to refractory materials prevailing in smelters and furnaces are highly complex. The refractory materials are exposed to fairly high temperatures, thermo-mechanical stresses, penetration of pores, erosion and chemical corrosion. The application of numerical simulation tools is needed for the refractory engineering task to consider those phenomena and to evaluate the impact of operational regimes on the refractory design and finally on the integrity of the furnaces. The work discusses case studies of simulations addressing problems and questions related to the refractory design process. Practical simulation approaches which employ simplified models are introduced as the engineering process demands results in a reasonable time.

By Lyall Workman

New mines are frequently located at altitudes above 3,000 meters (10,000 ft.). Drill selection must take the altitude effects into account, to insure high productivity and good bit life. In particular, compressors must be sized differently than for low altitude operation. A larger compressor is required to deliver adequate air to the bottom of the blasthole. Many drills in remote locations use diesel engines as the prime mover. Altitude effects on engine performance should also be considered.

Jan 1, 2007

By A. V. Kuznetsov, R. I. Kamkin, V. M. Paretskiy, A. Y. Mamaev, V. P. Bystrov, A. S. Vernigora

"Vanukov furnace technology is an efficient, proven pyrometallurgical injection technology, used extensively in Russia and Kazakhstan for a number of different applications. The technology was most widely adopted for processing copper sulfide concentrates for matte in smelters in Norilsk, Revda (Russia) and Balkhash (Kazakhstan). The following applications also were developed and tested at industrial scale: treatment of sulfide lead and lead-zinc concentrates, laterite nickel ore, production of cast iron, treatment of antimony gold-containing ores, and municipal solid waste. In this paper, current experience of Vanukov furnace application to these technologies is described with a number of general development trends and new areas of application.IntroductionAt the present time, the Vanukov process, developed at the Moscow State Institute of Steel and Alloys at the Department of metallurgy of non-ferrous, rare and noble metals with collaboration with other research organizations, is a highly efficient technological solution for processing different kinds of raw materials. The process was invented by Professor Andrey Vladimirovich Vanukov, whose research work began in 1949. From 1956 to 1975 test runs of the technology were carried out at the smelters in Norilsk and Balkhash. In 1976 a pilot Vanukov furnace was built in Ryazan. Furnace designs was modified to suit the various test programs. A major objective of each experiment was the determination of optimal working conditions for processing different types of raw materials such as copper, copper-nickel, copper-zinc, lead or pyrite concentrates, and materials containing secondary lead and zinc. After the death of Andrey Vladimirovich Vanukov in 1986, this technology and furnaces based on the technology were named after him: “Vanukov process” and “Vanukov furnace”. Today, the following furnaces based on Vanukov technology are either working or were tested at semi-industrial scale: three in Norilsk, two in Revda (Russia) and two in Balkhash (Kazakhstan) for treatment of copper sulfide concentrates for matte, one in Orsk (Russia) for processing laterite nickel ore, one in the Buruktal plant (Russia) for antimony gold-containing ores for antimony oxide sublimates and gold-containing metallic antimony, and one in China for processing sulfide lead and lead-zinc concentrates for production of black lead and zinc-containing sublimates."

Jan 1, 2011

By K. G. Philo, R. C. W. Webber-Youngman

mining, where data-driven decision making optimizes resource extraction, enhances safety, and ensures sustainability. The adoption of digital technologies like artificial intelligence (AI) and the Internet of Things has amplified the importance of digital information. However, the integrity and security of this information are paramount, leading to the exploration of blockchain technology as a potential solution for secure digital value exchange in mining. This research examines blockchain's capabilities, drawing insights from its applications in sectors like banking, government, healthcare, and entertainment, and evaluates their relevance to mining's core value chain processes. The study identifies blockchain's distributed ledger technology, cryptographic security, and decentralization as unique advantages that can revolutionize mining by enhancing transaction speed, reducing costs, and improving supply chain transparency and compliance with sustainability standards. Blockchain's transparent and auditable records can enhance business transparency, fostering trust among stakeholders, including investors and regulatory bodies. The technology's consensus mechanisms and smart contracts further promote trust in collaborative ventures. This research provides a foundational understanding for decision-makers in the mining industry to evaluate blockchain's feasibility and potential return on investment, guiding strategic planning and resource allocation for blockchain applications. By leveraging blockchain, mining companies can optimize operations, improve sustainability practices, and establish a robust foundation for future growth, positioning blockchain as a transformative technology in the sector

Jul 10, 2024

By W. R. Ingalls

WHAT proportion of the national wealth is represented by' the producing mines of the country?' Or by the- mining and metallurgical industry-as a whole, for it is impossible to make-an economic distinction between the mines that produce the ore and the plant that is used to get the metals from it. The total national wealth in fixed property is about $270,000,000,000. How much for the mines? I do not know that any one 'else has ever tried to furnish answers to these questions. In making such an attempt I am conscious that the result can be nothing more than a rough approximation. Yet even that will give an idea of relative values. No separate valuation for the mines of the country has appeared in any inventory of the national wealth previous to that which I compiled and published for 1916. -In earlier census estimates mines were supposed to be included under the head of real estate. However, an examination of the laws and practices of the several states with respect to mine taxation will make it evident that no good idea of the value of the mines of the coun¬try is obtainable from the assessment rolls. In my previous estimate for 1916, I computed the value of the mines at $8,000,000,000, which was approxi¬mately 10 times their net income as reported to the Bureau of Internal Revenue. In making that estimate I fell grossly into error, for several reasons that it is unnecessary to explain, but chiefly because the net income of the mines of the country in that year was exceptionally large. The whole subject of valuing the mines of the country en bloc is extraordinarily difficult At the best, no one can hope to arrive at, anything more than a rough idea about it. However, elements of reason may be introduced and may be made to serve as chief bases.

Jan 1, 1921

By M. Maldonado, J. A. Finch

"A flotation bank consists of a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three strategies for optimizing bank performance: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data is analyzed in respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.INTRODUCTION Flotation is used to separate valuable minerals from each other and from gangue. To reach a target metallurgical performance, usually assessed in terms of concentrate grade and recovery, feed is passed through stages such as roughing, cleaning and scavenging. All these stages comprise serial arrangements of flotation cells known as banks, lines or rows. Although a bank is the simplest interconnection of cells in a circuit, i.e. the tails of one cell is the feed to the next cell down the bank, how to operate each flotation cell in a way that the whole bank performance is optimized remains a challenge. Significant efforts have been made towards understanding the effect of operating variables on the flotation performance of an isolated cell (Lynch et al., 1981; Finch and Dobby, 1990; Gorain et al., 1998). However in the case of banks the variables that can be manipulated increase with the number of cells in the bank and the problem of how to manipulate them to achieve optimum performance is difficult even disregarding variation in ore characteristics (Lynch et al., 1981, p. 16). In general, the more manipulated variables available the better for optimization purposes, however without clear guidance how to effectively use them it becomes an “embarrassment of riches”."

Jan 1, 2012

By R. H. Walpole, J. M. Kane

IN all probability the mining and metallurgical industry as a whole can demonstrate a larger ecorlomic return from installation of dust-control equipment than any other major industrial group. This fact has partially accounted for the marked increase of dust-control installations made during the past decade. While the primary objectives for installation of dust-collecting systems are improved working and operating conditions for men and equipment, the fact that an economic return can be anticipated on salvageable materials is an added advantage which shows in partial or complete equipment write-off. The conditions apply to most phases of the mining, milling, and smelting industry, both non-metallic and metallic. As with any mechanical devices, selection of suitable dust collector equipment involves evaluation of available products with characteristics most nearly meeting conditions of the application at hand. When there is valuable product to be collected, and/or when there are possibilities of air pollution or public nuisance, collector selection is often guided by the maxim of "highest available collection efficiency at reasonable cost and reasonable maintenance." A brief review of dust collector designs will permit outlining of major characteristics of each group. Final selection will involve detailed data against a background of the problem under consideration. The dry centrifugal collectors, see Fig. 1, represent a group of low cost units with minimum maintenance. They are subject to abrasion under heavy abrasive dust loads and to plugging with moist materials. Efficiency drops off rapidly on particle sizes below the 10 to 20 micron group. Because of the large amounts of —10 micron particles in most mining dust problems, they will normally be used as primary collectors and will be followed by high efficiency units. This combination is cspecially popular where the bulk of material is desired in a dry state with wet collection indicated for the final cleanup portion. In remote plant locations, dry centrifugal~ can be used alone if product in dust form has no value or if dust loading is light enough to eliminate a nuisance in the plant area. Where high efficiency dust colleotion equipment must be selected, choice will normally involve fabric arresters, wet collectors, or high voltage Electro-Static precip-itators. Fabric arresters, see Fig. 2, rely on the passing of dust-laden air at low velocity through filter fabric. Velocity ranges from 1 to 3 fpm for the usual installation and may be as high as 10 to 20 fpm in arrangements where automatic frequent vibration or continuous cleaning of the filter media is employed. Fabric is normally suspended in either stocking type or in an enlvelope shape. Collection efficiency is excellent even on sub-micron particle sizes. Equipment is bulky, must be vibrated to remove the collected dust load, and is restricted in applications from temperature and moisture standpoints. Condensation of moisture on the fabric filter mcdia causes plugging of the passages with great reduction in air flow. Temperatures for the usual medias of cotton or wool are 180" and 200°F maximum, although the introduction of synthetic materials such as nylon, orlon, and glass cloth have increased the possibilities of this type of collector for higher temperature applications. The wet-type collector may employ a number of different principles so that entering dust particles in the gas stream are wetted and removed. Principles usually include impingement on collector surface or water droplets, often in combination with centrifugal forces. Variety of wet collector designs is indicated by typical collectors illustrated in Figs. 3 and 4. Collection efficiency is a function of the particular design, although the better collectors will have high collection efficiency on particles in the 1-micron range. Wet collectors have the advantage of handling hot or moist gases, take up small space, and eliminate secondary dust problems during the disposal of the material. At times collection of the material wet is a disadvantage. Wet collectors may also be subject to corrosion and freezing factors. The high voltage Electro-Static precipitator, see Fig. 5, is probably the most expensive type of high efficiency collector. It finds its applications generally in problems in which collectors previously discussed cannot be employed. Its collection efficiency is based on its design features and can be excellent on the finest of fume particles. Material is normally collected dry. Gas temperatures are of no great concern as long as condensation does not occur within the dry type of precipitator and the temperatures do not exceed the limits for materials used in its construction. As with the fabric arrester, provisions

Jan 1, 1954

By N. W. Xu, M. D. Wei, F. Dai, B. Li

"Chevron notched samples achieve general acceptance for measuring the Mode-I (opening mode) fracture toughness of rocks. The cracked chevron notched semi-circular bending (CCNSCB) sample, which is developed from the International Society of Rock Mechanics suggested the cracked chevron notched Brazilian disc method, has recently received much attention. However, these chevron notched methods have not been fully mastered, some ideal assumptions based by their theories and formulas, such as the straight-through crack assumption (STCA), have not been verified detailedly. Fractures of CCNSCB specimens were numerically simulated considering different heterogeneities, geometrical and mechanical parameters. The results show that, the real fractures of CCNSCB specimens are never satisfied with the STCA. In fact, micro fractures not only occur in the notch tip but also the two chevron edges. Consequently, the crack front features prominently in a shape of parabolic curve, far from being straightthrough. Moreover, curvature of the crack front is only affected by shape of the chevron ligament. Cracks usually start from two sides of the notch tips rather than center of the notch width, and propagate deviating from the postulated fracture routes. These fracture mechanisms induce errors with the measurements, and thus more attentions should be paid to the real fractures of the chevron notched samples for measuring fracture toughness more accurately. INTRODUCTIONWith the increasing requirement of people for resources and energies, frequent rock engineering activities have been conducting, such as underground excavation, oil exploration and deep burial of nuclear waste. Many problems appear in rock fracture. Consequently, there are more and more attentions paid in rock fracture mechanics due to its broad application prospects for solving these engineering problems. Since Mode-I (opening mode) fracture is the most common failure mode in rocks, Mode-I fracture toughness is a primary parameter to predict rock mechanical properties in actual engineering, and thus its accurate values are necessary to the researches of rockburst, rock mass slope stability, rock cutting, hydraulic fracturing, tunneling, et al. Therefore, it is thus significant to evaluate and study relevant methods to obtain the reliable value."

Jan 1, 2015

By David H. Browne

(Pittsburg Meeting, March, 1910.) NICKEL has always been a fruitful mother of problems. Previous to the year 1906 nickel was regarded as an element replacing iron in copper-mattes, and it was believed that the same laws which governed the elimination of iron could be applied-to nickel. This conception has lately undergone a complete change, and nickel in all its stages is now regarded as an element replacing copper; in other words, copper-nickel is considered now as two elements, but as one metal. When we commenced our investigations on Monel metal we made a great many experiments on the conversion of mattes, both high copper and high nickel. We studied closely the composition of the mattes and the changes produced by the blow. We found in all cases certain agreements which we believe are due to some law. Briefly stated, our conclusions are as follows 1. Nickel is not an element replacing iron in matte. 2. Nickel-copper alloys act in the matte-blow like one metal. 3. Nickel-copper alloys follow, during the matte-blow, exactly the same laws as govern. the behavior of copper alone. This brings up the question : What are the laws governing the production of metallic copper, and what are the relations copper to sulphur and iron during the Bessemer blow ?

Apr 1, 1910

By William F. Lawrence

Due to the immense volumes of municipal wastes that are generated in this nation every year, it has become imperative that effective measures be developed to utilize all or portions of these materials in a productive and efficient manner. Nany larger municipalities employ incineration to reduce the bulk of material to be removed to disposal sites: but, even after incineration, approximately one-fourth of the original waste material in the form of non-combustible residue and flyash remain. It has been found that the flyash fraction of the incinerator residue contains varying amounts of copper, silver, gold, aluminum, iron and titanium along with many other important metals. The serious loss of these natural resources contained within the flyash and the monetary expense of current disposal methods present a serious and rapidly increasing problem to the public and to the Federal Government. The growing emphasis upon environmental control, rapidly increasing urban population and "convenience packaging" 'with its attendant increased waste production has led to the initiation of a broad range of studies concerning municipal waste. For example, the U. S. Bureau of I-lines is investigating all aspects of the incineration of municipal waste under its solid waste disposal program.l "In-house" studies range from improved incinerator design to potential recovery and recycling of the various components within the incinerator residue. A major portion of the latter research is being performed at the U. S. Bureau of ;-lines, College Park, Maryland facility while grants for specific areas of study have been issued to several universities and research institutes. In addition, the Department of Health, Education and Welfare has supported programs examining the potential recovery of paper; glass, metals and other components of unincinerated refuse followed by disposal in sanitary landfills.

Jan 1, 1971

By Todd Smith, Brigitte Lacouture, Greg Anderson, David Lin

"The lead and zinc flotation circuits at Red Dog Mine are preceded by a preflotation circuit which recovers naturally-floating organic carbon contained in the ore. Organic carbon is a potential contaminant in the lead concentrate and is detrimental to lead-zinc selectivity. Prior to 2007, the Red Dog preflotation circuit consisted of a single stage bank of tank cells which floated the organic carbon. The preflotation concentrate was discarded directly to tailings, however, this stream contained significant amounts of lead and zinc. Zinc loss to preflotation ranged from 2% to 6%, relative to the zinc in the mill feed and was proportional to the amount of organic carbon in the ore. The main mechanism of the zinc loss was entrainment.Pilot plant and modeling testwork were conducted to examine the use of a Jameson Cell to clean the preflotation concentrate. Results indicated that up to 90% of the zinc deporting to preflotation concentrate could be returned to the flotation circuit for recovery. The installation of a 5.4 m Ø Jameson Cell with 18 downcomers was initiated in June 2006. The new preflotation cleaning circuit was commissioned in March 2007. Conservatively, preflotation cleaning has resulted in zinc and lead absolute recovery gains of 1.0% and 1.5%, respectively. The $9.1M project has a payback period of approximately 1 year at current metal prices.INTRODUCTIONRed Dog Preflotation CircuitRed Dog Mine is located above the Arctic Circle in northwest Alaska. It is the world’s largest zinc concentrate producer with a production rate of more than 1.0M t/yr. Red Dog is operated by Teck Cominco Alaska Incorporated under an operating agreement with the Northwest Alaska Native Association (NANA). Due to the remote location of the mine, it is accessible only by air, or seasonally, by ocean-going barges.The Red Dog deposit is a rich sedimentary exhalative (sedex) zinc-lead-silver deposit. The major sulphides, in decreasing order of abundance, are sphalerite, pyrite, galena and marcasite. Due to the complex nature of the ore body, run-of-mine ore is blended in stockpiles before being crushed and processed through the concentrator. The average mill feed grade for 2006 was 6.1% lead, 20.6% zinc, 8.0% iron and 0.67 % organic carbon."

Jan 1, 2008

By K. Biswas, P. Tsang, S. S. Peng

A survey was undertaken in late 1993 and early 1994 to gain insight into the current status of pillar-design practice in underground coal mines in the United States. A total of 552 room-and-pillar mines and 75 longwall mines were surveyed to collect general, geological and mine-plan information. The collected information was critically analyzed with special emphasis on the pillar-design criteria adopted in these mines. A safety factor analysis was also carried out for the pillars in the room-and-pillar mines.

Jan 1, 1997

This publication summarizes, for potential contractors and other interested parties, the proposed research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1977 (October 1, 1976-September 30, 1977) under its Advancing Coal Mining Technology program. The objective of these projects is to provide an ordered and sequenced series of advances toward the overall goal of providing the system technology required to increase the productivity of the coal mining process.

Jan 1, 1977

By R. J. Gajan

As part of its research program on secondary metal refining, the Federal Bureau of Mines has developed a fast method for determining aluminum, iron, copper, cadmium, and lead in zinc-base alloys. The new method is intended for use by trained technicians in laboratories with inexpensive equipment. It can be used either in the analytical laboratories of the many small plants that are characteristic of the secondary metals industry or in laboratories engaged in basic research to improve refining processes. A complete analysis for the foregoing elements can be made in less than 3 hours from a single sample in solution. The method is especially helpful when a small amount of sample is available. Aluminum and iron are determined spectrophotometrically and the other elements polarographically. The new method is now being used for control analysis in metallurgical research, and the results compare favorably with previously used spectrographic methods. Luke and Braun4/ described a photometric method for the determination of aluminum in zinc diecasting alloys in which the aluminum was complexed with Aluminon reagent (ammonium salt of aurintricarboxylic acid), forming a red lake. An adaptation of this method was used for determining aluminum. Beers law is obeyed between 0.01 and 0.06 milligram of aluminum.

Jan 1, 1961

By Clarence Karr

AN EXTENSIVE characterization was conducted on the neutral oil components in a low-temperature bituminous coal tar. A total of tai individual compounds identified with respect to individual isomers, and at least 55 other compounds were indicated to be present. The amounts were determined in all instances. A comparison of isomeric distribution in the tar with thermo-dynamic equilibrium distribution, and kinetic distributions indicated that the composition of the tar largely reflected the structure of the coal from which it was formed. Detailed descriptions are presented for the separatory and qualitative and quantitative procedures for the characterization of the neutral oil component. These include micro fractional vacuum distillation, displacement liquid chromatography, gas-liquid chromatography, countercurrent distribution, and infrared and ultraviolet spectrophotometry. Descriptions are given for the synthesis of authentic specimens of alkylindenes, The ultraviolet and infrared spectra of 134 polycyclic compounds, ranging from alkylindenes to alkylphenanthrenes, either found in the distillable neutral oil, or thought likely to be present, are also given.

Jan 1, 1967

By R. Bishop, J. Baggett, J. Monsalve, N. Ripepi, A. Soni

Technology plays an ever-increasing role in improving the safety and efficiency of mining operations. Laser scanning and photogrammetry are two useful methods for capturing 3D digital representations of real world objects. While both technologies have been applied to the mining industry in numerous ways, the practical applications in an operating underground limestone mine has been tested for this paper, including for visualization and site characterization. Each technology is capable of creating highly detailed geospatial point clouds, but are all point clouds created equal? This paper presents a comparison of a laser scan and photogrammetry of a limestone pillar and addresses the strengths and limitations of each method for creating digital models of operating underground limestone mines. INTRODUCTION The United States crushed stone business is a ~$14 billion per year industry representing 1,430 companies which operate 3,782 mining operations across the 50 states. In 2017 alone, 1.33 billion tons of crushed stone was produced with 76% used predominately for road construction and repairs, but also for the production of cement, lime, chemical and agricultural uses. Over 70% of domestic crushed stone producers source their material from limestone and dolomite deposits, with currently only 82 mines (2%) operating underground (USGS, 2018). Underground mining requires a different technical skillset, and poses great challenges for production that must be both safe and economical. Therefore, there are many risks that an operation must mitigate in order to produce underground limestone. Some of the challenges in underground limestone mining involve geological hazards that are unique to the rest of the industry. The geologic features such as faults and weaknesses can be difficult to assess in a production environment (NIOSH, 1998). The consequences of failure due to improperly designed underground mining ground support systems, such as from a roof failure, are not only life threatening for the miners themselves, but can easily shut down an entire mining operation.

Jan 1, 2019

By P Ramsaywok

The use of saline water for mineral beneficiation in arid regions is general practice and also the case with Exxaro Namakwa Sands, situated on the west coast of South Africa. Although it is ‘cost effective’ to use sea water for mineral beneficiation, downstream process separation efficiencies may be negatively affected. This is more specific to surface dependent separation techniques such as electrostatic and high tension (HT) separation. If minimal fresh water is available then, proper washing is often neglected. Salt crystals can form on particle surfaces during the drying process before electrostatic separation.This paper describes a study that has been conducted to determine the effect of upfront salt water processing on downstream electrostatic/HT separation. The study indicated that minor quantities of salt can cause the separation efficiency to decrease substantially.

Oct 5, 2011

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Edward Medina

El presente trabajo señala el método de minado "sublevel stoping" aplicado a través de la perforación de taladros largos ubicados cada 50 cm. en el yacimiento minero de San Rafael, Puno. Esta perforación acorta el tiempo de ejecución y el costo se reduce considerablemente en la preparación de la labor. Asimismo, la perforación radial minimiza la perturbación al macizo rocoso debido a que se realizan menos voladura en los alrededores, como también se tiene menos área expuesta a deformaciones. Finalmente, el uso de los equipos de última generación, permiten controlar mejor la desviación del taladro a mayor longitud, que en años anteriores fue uno de los principales limitantes.

Sep 13, 2001

By A McGann, P J. Coghill, D Miljak

"It is widely accepted that bulk ore sorting could provide a step change in processing of low-grade ores. For this to be achieved a rapid, accurate bulk sensor of grade is required as well as sufficient natural variation of grade in the ore stream. CSIRO trialled a magnetic resonance (MR) sensor capable of measuring chalcopyrite, and by inference total copper grade, on the 1300 t/h Ridgeway portal conveyor. The gauge produced an unprecedented set of data down to a 1 t scale for months at a time. This paper analyses the measured variation and compares it to a simple model derived from the bore core data and mixing within the block cave mine.The model of the small-scale (<1000 t) variation is developed using fractal methods which have successfully been used in the past for copper porphyry deposits showing a power law or near power law distribution of copper grade and vein sizes. These fractal distributions have two features highly favourable for segregating ore, a large proportion of low-grade pods and the large-scale spatial clustering of grade. We show the presence of fractal ordering in bore core data at short range in the Cadia Ridgeway porphyry deposit and measure its persistence in the crushed rock produced by the Ridgeway block cave mine over one month. The model is then extended to demonstrate the effect of varying head grade, mixing and pod (or diversion) weight on bulk sorting efficiency.CITATION:Coghill, P J, Miljak, D, McGann, A, 2016. Modelling Grade Variation in Crushed Ore at Cadia Ridgeway and Its Potential Consequences for Bulk Ore Sorting, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016