Search Documents

By H. C. George

This bulletin deals with prime movers, power-transmitting machinery, and the surface equipment and methods used to pump oil wells. It does not discuss geological problems nor the methods and equipment used in drilling or at flowing oil wells. Much of the presentation is by photographs and drawings which are described in the text. Underground equipment and methods for pumping oil wells will be discussed in a later publication of the Bureau of Mines.

Jan 1, 1925

By Leonello Sciacca

Deepening of harbours has become a priority, necessary to the ongoing operation of the wharves in the face of deeper draft merchant vessels and cruise ships. It is now standard practice in many areas to provide for harbours to be dredged to significant depths below mean sea level, in the order of 12.00 m (39 ft) for existing berths and 15.00 m (49 ft) for new wharf construction. The Ravenna Port Authority initiated a project to deepen the harbour bottom at selected wharves to a depth of 12.00 m (39 ft). In preference to reconstruction of the wharves with longer and heavier sheet piling or other equally disruptive reconstruction, they identified the structural reinforcement of the existing wharves by means of deep underwater tie rods as a possible alternative cost-effective solution. Having defined the design concept, effort was concentrated on developing the required technology. A technique, already in use for the installation of tie rods by means of robotics, was identified as potentially suitable for underwater use. It was decided to carry out the fine tuning and the evolution of the technology for a marine environment of the robot unit and of the related remote control software that controls the installation of the tie rods. An experimental test site was set up to refine the drilling, installation, grouting, monitoring and testing of underwater tie rods. The purpose was to confirm the feasibility of the proposed solution and the reliability of these tie rods for use in the reinforcement and construction of wharves. The paper also discusses the theoretical and experimental study of underwater tie rods dealing with the theoretical analysis of the interaction between tie rod and soil, aimed at identifying the correlation between the forces of applied traction and the corresponding measured elongations. A series of tests were carried out with positive results, both at the operating load of 300 kN (67 kips) and at the nominal maximum load of 630 kN (142 kips). The tests were carried out on seven tie rods, of which three were installed at a depth of 5.00 m (16 ft), principally to test the reliability of the operating and remote control systems in the presence of a significant hydrostatic pressure, and four were placed at a depth of 8.00 m (26 ft) to check the load bearing capability of the tie rods positioned at the depth called for by the current project.

Jan 1, 2011

One of the most important parameters in mine ventilation planning is the friction factor (K). Accurate values of friction factors are critical especially when carrying out mine ventilation simulations. No computer simulation of a mine ventilation network is meaningful if the airway resistances are not accurately estimated (when planning a new mine) or measured (for an existing mine). However, in the first case not many reliable values of friction factors exist in the international literature. This paper presents the results of a research project carried out in the province of Quebec where ventilation friction factors were measured in all underground metal mines. These friction factors are statistically analyzed and tabulated. A friction factor database was created that also includes the friction factors measured in the past by other people. This database can help the mine engineer to accurately estimate ventilation friction factors according to the specific conditions. This database offers several values of friction factors typical for hard rock mine conditions typical of modern underground metal mines.

Jan 1, 2009

By F. N. Kissell, C. D. Litton

This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

Jan 1, 1993

By J. S. Stachulak

The Diesel Emissions Evaluation Program (DEEP), a research consortium formed in 1997 by Canadian mining companies, labour unions, and provincial and federal government departments, completed its work by mid-2006. This program, in which Vale Inco participated with both direct funding and in-kind contributions, investigated the ability of currently available technology to significantly reduce underground concentrations of diesel particulate matter (DPM) with high efficiency and low maintenance over a long-term period (years of life).While DEEP?s testing showed that engine maintenance is a critical component for lowering DPM, it was clear that reduction of DPM to the very low target levels of ~0.05 mg/m3 was not possible with maintenance alone. The best candidate technology for achieving low DPM levels was particulate filter systems. Furthermore, successful deployment of such systems was highly dependent on removing them from having to rely on human intervention for their regeneration. The search continues within Vale Inco to identify a reliable and rugged system.

Jan 1, 2009

By S. H. Ash

THE ANTHRACITE region of Pennsylvania contains over nine-tenths of the total anthracite deposits of North America and produces all but an insignificant proportion of the total output of anthracite in the Nation. The whole economy of the northeastern section of the United States depends, to a large extent, on the mining of Pennsylvania anthracite, which is shipped to New Jersey, New York, and New England and is a principal source of energy and heat for that entire region. The responsibility of the Federal Government for developing an engineering method that will prevent inundation of the Pennsylvania anthracite mines and keep them in operation has long been recognized. To obtain a reliable picture of the anthracite-mine-water problem and to solve that problem, it is necessary to have factual data on the volume and the quality and character of the mine water handled by the pumping plants in the anthracite region, as well as the kinds of pumps utilized and problems concerning their operation.

Jan 1, 1953

By F. N. Kissell, C. D. Litton

Abstract-This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

By Ke Yang

In Chinese coal mines, extraction of deep, highly gassy soft coal seams sandwiched between soft floor and soft roof in complicated geology is commonly encountered. How to safely and efficiently excavate such seams is a very significant and important problem. It has been a focused research area in recent years. By combining the characteristics of fully mechanized longwall mining methods such as large cutting height and mining along the dip, an integrated method and technologies for the Zhangji Coal Mine were developed. This technology includes the design of a complicated geological exploration system, optimization of mining method and working face parameters, control of rock pressure and high levels of gas, reliability model of the production system, and selection and compatibility of equipment. Engineering practice shows that the integrated technology was successful in mining these complicated seams. This study not only enriches the mining method, but also improves the coal mining practice, especially ensuring both safety and productivity under complicated geological conditions.

Jan 1, 2009

By G. Broadbent

It is an honour to be invited as a speaker to this ICCR conference and a pleasure to be with you here in South Africa. I have been asked to talk about the competitiveness of coal versus other energy alternatives. Coal supplies nearly one-quarter of the global primary energy. Its most direct competitors are gas, nuclear and renewables. Oil is predominantly for transport fuels. Fuel oil is competitive with coal when crude is below its long-run average price and has some niche opportunities. But I will confine my comments to nuclear, renewables and particularly natural gas as the most potent current competitive threat to coal. Competitiveness is more than just cost and price; there is environmental acceptability, security or reliability and increasingly image. These factors are more of a spectrum than discrete issues. Dollars and cents remain the key issue for competitiveness but one must recognize the impact of politics in sustainable development and energy security.

Jan 1, 2001

By L. Tercero Espinoza, F. Marscheider-Weidemann, C. Gandenberger

"A reliable supply of non-energy raw materials is a precondition for the functioning of the European economy. In line with its importance, the issue of raw materials supply has become more prominent in the past years, especially owing to turbulent raw material markets. However, these turbulences are not due to depletion of the geological resources but to a missmatch of (expected) supply and (expected) demand, with several interacting factors influencing the markets both from the supply as well as from the demand side. A recent evaluation, published in June 2010 within the framework of the EU Raw Materials Initiative, sought to bring together these two sides of raw material markets and asked the question "which raw materials are critical for the EU?" Herein we present the methodology used by the Ad-hoc Working Group on Defining Critical Raw Materials and the results obtained, complemented by results from the study "Raw Materials for Emerging Technologies"."

Jan 1, 2011

By F. Dahl, P. Raleigh, J. Holzhauser, B. Nilsen

Tunnel excavation using tunnel boring machines (TBMs), has become increasingly common in recent years, despite the fact that precise evaluation of certain risks have not kept pace with the use of these machines. One of the risks easily overlooked by Engineer and Contractor alike are the effects of abrasive ground on the costs and schedule of a given project. The impacts of worn and damaged TBM cutter heads have been observed on hundreds of tunnel projects around the world. It would appear that a reliable prognosis of the abrasiveness of soils on a project would be of great importance for designers, clients and contractors alike. Several well acknowledged test and prognosis methods already exist for rock, however there is only very limited knowledge available to describe the abrasiveness of soil and its impact on soft ground TBMs. This paper will examine approaches to this problem and suggest a new approach based on a current project undergoing design.

Jan 1, 2007

LARGE-SCALE production of zirconium by the Northwest Electrodevelopment Laboratory of the Bureau of Mines at Albany, Oreg., is an anomaly that justifies some explanation. The reduction of titanium tetrachloride with magnesium in an inert atmosphere, as perfected by Dr. W. J. Kroll before 1940, aroused renewed interest in zirconium, and in 1945 development work on this metal was initiated at Albany under Dr. Kroll's technical direction. Preliminary results were promising, and in February 1947 a pilot plant with a weekly capacity of 60 pounds of zirconium-metal sponge was put in operation. Shortly thereafter the Oak Ridge National Laboratory of the Atomic Energy Commission requested production of 1 ton of zirconium-metal sheet, with the provision that it have a low hafnium content. The Bureau of Mines was furnished with a. supply of Brazilian baddeleyite ore, containing less than 1 percent hafnium with respect to zirconium, from which was made about. 2,700 pounds of relatively low hafnium zirconium sheet of 0.080-inch thickness for test purposes. This was accomplished by melting zirconium sponge in a graphite crucible, hot-rolling the ingot in an iron sheath, and finishing by cold rolling. Concomitantly the Oak Ridge Laboratory developed a method for separating hafnium from zirconium; and, in cooperation with the Atomic Energy Commission and the Bureau of Ships of the Department of the Navy, a, larger pilot plant was erected to produce zirconium from very low hafnium zirconium tetrachloride furnished by the Commission. Pilot-plant work on producing zirconium tetrachloride from zircon sand and baddeleyite was discontinued. Production of zirconium sponge in the larger pilot plant of 500 pounds per week capacity was begun in June 1949.

Jan 1, 1956

The value of processed materials of mineral origin was estimated to have exceeded $310 billion in 1990. U.S. raw nonfuel minerals mine production in 1990 was estimated at $33 billion, a 3.1 % increase over that of 1989. The value of minerals production increased in all but 3 of the last 30 years. The metals component of production value has fluctuated much more than the industrial minerals component. This reflects the greater volatility of metal prices. In 1990, total employment in metal mining continued the increase that began in 1987. This growth was partially offset by a slight decline in employment in industrial mineral mining, resulting in an overall in-crease of 1.1 % to 179,100 in 1990. Continuing high (by historical standards) metal prices led to expansions at some mines, as well as opening or reopening of additional mines, resulting in increased employment.

Jan 1, 1991

By Ronald W. Stingelin

This study undertook the development and implementation of a methodology for estimating the impact of coal seam interaction on the eastern bituminous underground reserve base as published in USBM Information Circular 8655. The effects of previous mining in multiple coal seam areas on currently mined and reserve seams are predicted as a percentage coal loss by an engineering assessment model called the Coal Loss Calculation Model. The model utilizes twelve input variables easily derivable from mine maps or other existing data sources and calculates the effects of subsidence and high-stress due to remnant pillars in the previously mined seam. Extensive literature review resulted in the identification, definition, and quantification of the critical variables of seam interaction. Export opinion surveys were made of mining experts, MESA mine inspectors, and coal mine operators. Statistical analysis was used to establish the redundancy of the critical variables and to develop a total coal loss prediction algorithm. A regional analysis resulted in the production of a series of thematic maps on coal characteristics and distribution. A derivative map showing the areas of commonality within the eastern bituminous coal region served as the basis for implementation of the coal loss calculation model. The model was developed and tested using data from four coal mines in western Pennsylvania and southern West Virginia.

Jan 1, 1976

By Scott W. Hazen

METHODS of determining the grade and tonnage in a mineral deposit have not kept pace with scientific developments in certain other fields. The most commonly used methods of computing ore reserves and grade based on diamond-core-drill sampling are the cross section, the polygon, and the triangle. Tonnage and grade may be determined by these methods with acceptable accuracy, providing a sufficient number of samples is obtained; however, there is no means of determining when an adequate number has been taken or conversely if the deposit has been sampled excessively. It is demonstrated that, by using the techniques of statistical analysis, a mining engineer will be able to determine when a sufficient number of samples has been taken to determine the grade of a mineral deposit within a specified degree of confidence. Using statistical analysis to compute the estimated average grade of the ore makes it possible to compute a fiducial interval, when a distribution of the sample means is normally distributed, so that there is 95-percent confidence in the statement that the true average grade of the deposit is covered by the interval. This report utilizes data obtained from the Maggie Canyon manganese deposit, Artillery Mountains region, Mohave County, Ariz. Four separate exploration projects were conducted at Maggie Canyon between 1936 and 1950. Present economic conditions have made it desirable to determine the amount of 5-percent manganese ore developed by these projects.

Jan 1, 1957

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

By C. Scheffer

This paper describes a model that can simulate the behaviour of a pneumatic intensifier that is generally referred to as an ?air pump? (AP). The AP is used in many South African underground mines, and utilizes compressed air with pressures between 0.3?0.6 MPa to pump water up to pressures of 12?18 MPa. The high pressure water is used in numerous underground mines to pressurize props and roof bolts that act as safety and roof support devices. The simulation model reproduces the intensifier's operation under various conditions and therefore can be used to investigate the AP's sensitivity towards environmental conditions, design parameters (such as spring stiffness, plunger diameter, nozzle diameter etc.) and operating conditions. Model validation by comparison with laboratory experiments showed good correlation. The model can subsequently be used to investigate design changes aimed at improving the AP's performance and reliability over a wider range of operating conditions.

Jan 1, 2005

To provide a means for accurately and reliably warning of impending roof falls or rock bursts and for evaluating support systems. The Approach: Development of a device for measuring rockbolt loads which is not affected by harsh environments nor by eccentric loading conditions and is easily adapted to various size rock bolts. How It Works: The Rock-Bolt Tension Load Cell, developed by the Bureau's Spokane (Wash.) Mining Research Center, is installed on a bolt and sandwiched between a conventional doughnut washer bearing plate and a torqueing nut (Fig. 1). As the bolt takes load, the bearing plate transmits the load axially to the cell through a ball and socket arrangement, compensating for uneven bearing surfaces. The cell body strains in proportion to the applied load: the strain is sensed by welded strain gages as change in electrical resistance. The resistance change is read through a Wheatstone Bridge and, through calibration, the applied load is determined.

Jan 1, 1974

By D. K. Denton, M. J. Friedel, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep ( > 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Feb 24, 1997

By Kenji Koga

In order to derive the population distribution of gold nanoparticle morphologies as a function of size, highresolution electron microscopic (HREM) observations and structural analyses were done for over 4000 particles (3-18 nm) grown by an inert gas aggregation (IGA) source using helium. To obtain structural features threedimensionally and not to skip high-contrast images, twenty photos were taken for each particle by changing tilting angle of a specimen holder in combination with the through-focus procedure. For the reliable structural determinations, HREM images and their tilting sequences were directly compared with multislice-simulation results for icosahedral, decahedral and face-centered cubic morphologies, and finally the population distribution of each morphology was obtained as a function of size. In the present sample, icosahedral particles were dominantly populated over the whole observed size range and decahedral particles with non-spherical truncated bi-pyramid shape were secondly dominant. Even though a large number of sampling has been done, few crystalline particles were observed.

Oct 1, 2003